| 3M™ Ceramic Microspheres W-210 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M c...view more 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-210 are typically chosen over other 3M ceramic microspheres for higher gloss formulations. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. view less | |
| 3M™ Ceramic Microspheres W-410 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler load...view more 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-410 are typically chosen over other 3M ceramic microspheres for their overall balance in properties. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. view less | |
| 3M™ Ceramic Microspheres W-610 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic m...view more 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-610 are typically chosen over other 3M ceramic microspheres for increased durability. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. view less | |
| 3M™ Fluorosurfactant FC-4430 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...view more 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4430 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product can provide stain and dirt pick up resistance. view less | |
| 3M™ Fluorosurfactant FC-4432 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...view more 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4432 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. view less | |
| 3M™ Fluorosurfactant FC-4434 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...view more 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4434 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. view less | |
| 3M™ Glass Bubbles iM16K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...view more 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles iM30K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...view more 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K1 | 3M Advanced Materials Division | 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...view more 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K15 | 3M Advanced Materials Division | 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....view more 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K20 | 3M Advanced Materials Division | 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....view more 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K25 | 3M Advanced Materials Division | 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....view more 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K37 | 3M Advanced Materials Division | 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...view more 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K42HS | 3M Advanced Materials Division | 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...view more 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles K46 | 3M Advanced Materials Division | 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...view more 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S15 | 3M Advanced Materials Division | 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....view more 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S22 | 3M Advanced Materials Division | 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...view more 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S28HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...view more 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S32 | 3M Advanced Materials Division | 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...view more 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S35 | 3M Advanced Materials Division | 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...view more 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S38 | 3M Advanced Materials Division | 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...view more 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S38HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush streng...view more 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S42XHS | 3M Advanced Materials Division | 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...view more 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S60 | 3M Advanced Materials Division | 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...view more 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles S60HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...view more 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Glass Bubbles XLD3000 | 3M Advanced Materials Division | 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush str...view more 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. view less | |
| 3M™ Stain Resistant Additive and Sealer SRA-250 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product pe...view more 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-250 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-250 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. view less | |
| 3M™ Stain Resistant Additive and Sealer SRA-270 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The ...view more 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-270 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-270 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. view less | |
| 3M™ Stain Resistant Additive and Sealer SRA-450 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the...view more 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-450 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-450 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. view less | |
| 3M™ Stain Resistant Additive and Sealer SRA-451 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates th...view more 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-451 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-451 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. view less | |
| 3M™ Stain Resistant Additive SRC-220 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product...view more 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRC-220 offers durability, long-lasting performance and UV resistance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRC-220 is easy to incorporate into existing water and some solvent-based products and can be added to existing formulations or diluted with water or water miscible solvents and used as a stand-alone sealer. view less | |
| Easy Clean Coatings 1000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time...view more 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. view less | |
| Easy Clean Coatings 4000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-4000 is a fluoropolymer used for coating ceramic and glass surfaces. Once it air-dries, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. | |
| Easy Clean Coatings 6000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, he...view more 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. view less | |
| LC-L1V3 (UV-LED Source) | Hamamatsu Corporation | The LC-L1V3 UV-LED Spot Light Source features a compact body which fits into narrow confined spaces. Choose between two high output intensity models: 10500 mW/cm2 at 365 nm and 15000 mW/cm2 at 385 nm. It is extremely stable and has a high output at a lowe...view more The LC-L1V3 UV-LED Spot Light Source features a compact body which fits into narrow confined spaces. Choose between two high output intensity models: 10500 mW/cm2 at 365 nm and 15000 mW/cm2 at 385 nm. It is extremely stable and has a high output at a lower power consumption (25W) and cost than other models. view less |  |
| LC-L2 (Modularized UV-LED Light Source) | Hamamatsu Corporation | The LC-L2 modular spot light source is comprised of a small LED driver (part #: C10559-01) and an LED head unit (part #: L10561 and L10906 series). This UV-LED modular spot light source is very compact with high output intensity light, long life and low p...view more The LC-L2 modular spot light source is comprised of a small LED driver (part #: C10559-01) and an LED head unit (part #: L10561 and L10906 series). This UV-LED modular spot light source is very compact with high output intensity light, long life and low power consumption. An unusual feature of this unit is that it does not have a fan and does not require one for cooling, making this an easy addition to a clean room. Various LED head units with different irradiation patterns and sizes are available. view less |  |
| LC-L5 G (UV-LED Light Source) | Hamamatsu Corporation | A linear irradiation type UV-LED unit, the LC-L5 G has high output (10,000 mW/cm^2), air cooling by fan, and a compact and light weight. It is recommended for UV ink drying, UV coating agent drying, and for fluorescence excitation/scratch & flaw inspectio...view more A linear irradiation type UV-LED unit, the LC-L5 G has high output (10,000 mW/cm^2), air cooling by fan, and a compact and light weight. It is recommended for UV ink drying, UV coating agent drying, and for fluorescence excitation/scratch & flaw inspection lighting. view less | |
| LC-L5 (UV-LED Light Source) | Hamamatsu Corporation | A linear irradiation type UV-LED unit, the LC-L5 comes in a new smaller package and will work in new production processes and devices which can not accomodate conventional lamps. The UV-LED spot lights are 90% smaller, use 1/30th power as ordinary UV lamp...view more A linear irradiation type UV-LED unit, the LC-L5 comes in a new smaller package and will work in new production processes and devices which can not accomodate conventional lamps. The UV-LED spot lights are 90% smaller, use 1/30th power as ordinary UV lamps, and cut CO2 emissions by 20,000 kg per year. These units produce stable and accurate outputs with a long service life and require no duct installation or chillers. view less |  |
| LC8 | Hamamatsu Corporation | The LC8 UV Spot Light Source is available in different configurations, a front light guide port (part #: L9588 series) or a rear light guide port (part #: L9566 series). Each configuration is available in three wavelength ranges. Features include long lif...view more The LC8 UV Spot Light Source is available in different configurations, a front light guide port (part #: L9588 series) or a rear light guide port (part #: L9566 series). Each configuration is available in three wavelength ranges. Features include long life time (4000 hours), and easily changeable lamps for low down time. view less |  |
