| EXOCOAT™ AM | Axcentive Sarl | EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down v...view more EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down viruses and bacteria. It eradicates viruses such as influenza, SARS-COV-2, dengue & hepatitis and bacteria such as E. coli, MSRA, streptococcus, listeria, pneumonia, and salmonella. It is activated by light and displays quick drying at room temperature. Spray application is recommended to reach thin monolayers. It exhibits curing at room temperature up to 300°C and super hard particles (1GPa Vickers). It is easy to apply & durable, allowing longer disinfection intervals while preserving hygiene level. It shows non-silver leaching, efficacious even under low light conditions, lower service frequency, and no need for frequent disinfection routine. It is used in the state-of-the-art continuous antimicrobial coating for high-traffic areas. EXOCOAT® AM is suitable for topcoats for any surface inside buildings, stores, hospitals, and vehicles. The shelf life of this product is 9 months. view less | |
| Ketjenflex® 12 | Axcentive Sarl | Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl com...view more Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl compounds, and PVC based plastisols. It can also be used in PVC based polymers, nitrocellulose resins, and cyanoacrylate adhesives. view less | |
| Ketjenflex® 6 | Axcentive Sarl | Ketjenflex® 6 is a toluene sulfonamide in the form of a white crystalline powder. It is used as a plasticizer in inks, adhesives, and coatings. Ketjenflex® 6 can be used with resins such as nitrocellulose, polyamide, PVAC, rosin, epoxy, and more. | |
| Ketjenflex® 8 | Axcentive Sarl | Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coa...view more Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coatings, synthetic polyamides, epoxy coatings and adhesives, and more. view less | |
| Ketjenflex® 9S | Axcentive Sarl | Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wo...view more Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wood adhesives, epoxy and polyurethane coatings and adhesives, and other applications. view less | |
| Ketjenflex® CP | Axcentive Sarl | Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings. | |
| Ketjenflex® MH | Axcentive Sarl | Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printi...view more Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printing inks. view less | |
| Ketjenflex® MS 80 | Axcentive Sarl | Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured in...view more Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured into desired formulations. It has applications in nitrocellulose coatings, cellulose acetate formulations, and printing inks. view less | |
| nolax A21.2007 | nolax AG (Vanora) | nolax A21.2007 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film based on modified polyolefines and can be processed with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2007 h...view more nolax A21.2007 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film based on modified polyolefines and can be processed with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2007 has a melting point of 80 to 90°C, relative density of 0.94 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2007-S | nolax AG (Vanora) | nolax A21.2007-S is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film based on modified polyolefines and can be processed with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2007...view more nolax A21.2007-S is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film based on modified polyolefines and can be processed with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2007-S has a melting point of 80 to 90°C, relative density of 0.94 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2008 | nolax AG (Vanora) | nolax A21.2008 is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2008 has a meltin...view more nolax A21.2008 is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2008 has a melting point of 115 to 130°C, relative density of 0.9 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2008 S | nolax AG (Vanora) | nolax A21.2008-S is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2008-S has a me...view more nolax A21.2008-S is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2008-S has a melting point of 115 to 130°C, relative density of 0.9 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2010 | nolax AG (Vanora) | nolax A21.2010 is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2010 has a meltin...view more nolax A21.2010 is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2010 has a melting point of 135 to 145°C, relative density of 0.9 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2010 S | nolax AG (Vanora) | nolax A21.2010-S is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2010-S has a me...view more nolax A21.2010-S is a slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines and can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. A21.2010-S has a melting point of 135 to 145°C, relative density of 0.9 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2014 PE40 | nolax AG (Vanora) | nolax A21.2014 PE40 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on copolyamides. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2014 P...view more nolax A21.2014 PE40 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on copolyamides. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2014 PE40 has a melting point of 170 to 190°C, relative density of 1.1 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2015 | nolax AG (Vanora) | nolax A21.2015 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on copolyamides. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2015 has a ...view more nolax A21.2015 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on copolyamides. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2015 has a melting point of 105 to 115°C, relative density of 1.2 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2015 S | nolax AG (Vanora) | nolax A21.2015-S is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on copolyamides. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2015-S ha...view more nolax A21.2015-S is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on copolyamides. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2015-S has a melting point of 105 to 115°C, relative density of 1.2 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2026 | nolax AG (Vanora) | nolax A21.2026 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on polyethylenevinyl acetate. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A2...view more nolax A21.2026 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on polyethylenevinyl acetate. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2026 has a melting point of 60 to 75°C, relative density of 1.0 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2294 | nolax AG (Vanora) | nolax A21.2294 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.22...view more nolax A21.2294 is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2294 has a melting point of 125 to 135°C, relative density of 0.92 to 0.95 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A21.2294 S | nolax AG (Vanora) | nolax A21.2294-S is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21....view more nolax A21.2294-S is a sheet of slightly opaque colored thermoplastic hotmelt adhesive film built on modified polyolefines. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A21.2294-S has a melting point of 125 to 135°C, relative density of 0.92 to 0.95 g/cm³, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A22.2235 | nolax AG (Vanora) | nolax A22.2235 is a sheet of slightly opaque colored thermoplastic adhesive multilayer film built on modified polypropylene and copolyamides that are suitable for bonding textiles. It can be handled with all established lamination, calendaring, and bondin...view more nolax A22.2235 is a sheet of slightly opaque colored thermoplastic adhesive multilayer film built on modified polypropylene and copolyamides that are suitable for bonding textiles. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A22.2235 has a melting point of 120 to 145°C, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax A22.2235 S | nolax AG (Vanora) | nolax A22.2235-S is a sheet of slightly opaque colored thermoplastic adhesive multilayer film built on modified polypropylene and copolyamides that are suitable for bonding textiles. It can be handled with all established lamination, calendaring, and bond...view more nolax A22.2235-S is a sheet of slightly opaque colored thermoplastic adhesive multilayer film built on modified polypropylene and copolyamides that are suitable for bonding textiles. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A22.2235-S has a melting point of 120 to 145°C, is insoluble in water, is dry cleaning resistant, and not readily biodegradable. view less | |
| nolax C35.3030 | nolax AG (Vanora) | nolax C35.3030 is a water-born dispersion for water vapor barrier and heat seal coatings on different substrates, and emulates a white transparent and practically odor-free film. With a base of ethylene-copolymer, its suggested use is in metals, carton, p...view more nolax C35.3030 is a water-born dispersion for water vapor barrier and heat seal coatings on different substrates, and emulates a white transparent and practically odor-free film. With a base of ethylene-copolymer, its suggested use is in metals, carton, polyethylene, paper, and coating to coating. nolax C35.3030 can be applied by roll coating or air knife methods, has a density of approximately 1.0 g/cm³, a viscosity of 200 to 1000 mPa•s at 20°C, a pH value of 7.5 ± 1, and a particle size of approximately 250 nm. view less | |
| nolax M11.185 | nolax AG (Vanora) | nolax M11.185 is a solid, cloudy yellow colored, non-skin irritating, pressure sensitive hot melt adhesive that can be applied by slot-die and nozzle, screen printing systems and roll coating for self-adhesive coating of products that are in direct skin c...view more nolax M11.185 is a solid, cloudy yellow colored, non-skin irritating, pressure sensitive hot melt adhesive that can be applied by slot-die and nozzle, screen printing systems and roll coating for self-adhesive coating of products that are in direct skin contact. Tests for dermatological harmless approval must be checked, for each application. view less | |
| nolax M11.230 | nolax AG (Vanora) | nolax M11.230 is a solid, cloudy and somewhat yellowish in color, non-skin irritating, pressure sensitive hot melt adhesive. It can be applied by slot-die and nozzle, screen printing systems and roll coating for self-adhesive coating of products that are ...view more nolax M11.230 is a solid, cloudy and somewhat yellowish in color, non-skin irritating, pressure sensitive hot melt adhesive. It can be applied by slot-die and nozzle, screen printing systems and roll coating for self-adhesive coating of products that are in direct skin contact. Tests for dermatological harmless approval must be checked, for each application. nolax M11.230 has a flash point greater than 250 °C, a viscosity of 12700 mPa•s at 160°C, and a melting point of ~108 °C. view less | |
| nolax M11.342 | nolax AG (Vanora) | nolax M11.342 is a solid yellow colored, non-skin irritating, pressure sensitive hot melt adhesive. It can be applied by slot-die and nozzle, screen printing systems and roll coating for self-adhesive coating of products that are in direct skin contact. T...view more nolax M11.342 is a solid yellow colored, non-skin irritating, pressure sensitive hot melt adhesive. It can be applied by slot-die and nozzle, screen printing systems and roll coating for self-adhesive coating of products that are in direct skin contact. Tests for dermatological harmless approval must be checked, for each application. nolax M11.342 has a flash point greater than 250 °C, a viscosity of 13500 mPa•s at 160°C, and a softening point of 100 °C. view less | |
| nolax M14.1070 | nolax AG (Vanora) | nolax M14.1070 is a solid viscous liquid, slightly yellowish in color, UV-curable pressure sensitive hot melt adhesive, with high cohesion and high peel strength. The suggested uses are in UV curable hot melt, for direct skin contact, having a low odor an...view more nolax M14.1070 is a solid viscous liquid, slightly yellowish in color, UV-curable pressure sensitive hot melt adhesive, with high cohesion and high peel strength. The suggested uses are in UV curable hot melt, for direct skin contact, having a low odor and high MVTR. Depending on the viscosity, the adhesive can be processed on slot die, screen printing, and roller coating equipment. Tests for dermatological harmless approval must be checked, for each application. nolax M14.1070 has a flash point greater than 150 °C and a viscosity of 63000 mPa•s at 130°C. view less | |
| nolax S21.2018 PE40 | nolax AG (Vanora) | nolax S21.2018 PE40 is a sheet of slightly opaque colored thermoplastic adhesive film based on polyurethanes and can be processed with all established lamination, calendaring, and bonding techniques, except for high frequency welding. S21.2018 PE40 has a ...view more nolax S21.2018 PE40 is a sheet of slightly opaque colored thermoplastic adhesive film based on polyurethanes and can be processed with all established lamination, calendaring, and bonding techniques, except for high frequency welding. S21.2018 PE40 has a melting point of 65 to 85°C, relative density of 1.16 g/cm³, is insoluble in water, and is not readily biodegradable. view less | |
| nolax S22.2202 | nolax AG (Vanora) | nolax S22.2202 is soft, slightly rubber elastic, thermoplastic polyurethane adhesive multilayer film with decent transparency, that provides worthy attachment between incompatible, dissimilar substrates in light weight structures (sandwich boards) as well...view more nolax S22.2202 is soft, slightly rubber elastic, thermoplastic polyurethane adhesive multilayer film with decent transparency, that provides worthy attachment between incompatible, dissimilar substrates in light weight structures (sandwich boards) as well as technical textiles. Adheres on one side to metals and polyolefinic substrates (PE, EVA, EPDM), and on the other side to painted sheet material, glass, PC, PVC, PU, ABS, PA, and more. It can be handled with all established lamination, calendaring, and bonding techniques except for high frequency welding. nolax A22.2202 has a melting point of 100 to 130°C, relative density of ~1.0 g/cm³, is insoluble in water, and not readily biodegradable. view less | |
| nolax S22.2272 | nolax AG (Vanora) | nolax S22.2272 is a sheet of black colored thermoplastic adhesive film based on modified polyolefines that is used for the lamination of ballistic fabrics. It has a melting point of 120 to 130°C, relative density of 0.93 g/cm³, and not readily biodegradab...view more nolax S22.2272 is a sheet of black colored thermoplastic adhesive film based on modified polyolefines that is used for the lamination of ballistic fabrics. It has a melting point of 120 to 130°C, relative density of 0.93 g/cm³, and not readily biodegradable. view less |
