| MAXGARD® 1000 | Lycus Ltd. | MAXGARD® 1000 is a light yellow powder UV light stabilizer used for protecting polyurethane coatings, oil paints and acrylic adhesives. This product has a melting point of 195-197°C and a mass density of 1.21 g/cm3 at 25°C. It exhibits a broad absorption ...voir plus MAXGARD® 1000 is a light yellow powder UV light stabilizer used for protecting polyurethane coatings, oil paints and acrylic adhesives. This product has a melting point of 195-197°C and a mass density of 1.21 g/cm3 at 25°C. It exhibits a broad absorption band which extends into the UV-A range. voir moins | |
| MAXGARD® 1030 | Lycus Ltd. | MAXGARD® 1030 is a light yellow powder that is a special blend of benzophenone-2 and benzophenone-6, making it an effective light stabilizer for protecting coatings against UV radiation. This product has a mass density of 1.26 g/cm3 at 25°C and an absorpt...voir plus MAXGARD® 1030 is a light yellow powder that is a special blend of benzophenone-2 and benzophenone-6, making it an effective light stabilizer for protecting coatings against UV radiation. This product has a mass density of 1.26 g/cm3 at 25°C and an absorptivity of 52 at 339nm. It is suitable for use in polyurethane coatings, furniture stains and varnishes, nitrocellulose lacquers, fluorescent pigments and acrylic adhesives. voir moins | |
| MAXGARD® 2700 | Lycus Ltd. | MAXGARD® 2700 is a light yellow powder that can be used as an UV stabilizer for protecting coatings from the damaging UV radiation which is a component of natural sunlight. This product has a melting point of 175°C and a mass density of 1.19 g/cm3 at 25°C...voir plus MAXGARD® 2700 is a light yellow powder that can be used as an UV stabilizer for protecting coatings from the damaging UV radiation which is a component of natural sunlight. This product has a melting point of 175°C and a mass density of 1.19 g/cm3 at 25°C. It is suitable for use in polyurethane coatings, epoxy coatings, vinyl and acrylic adhesives. voir moins | |
| MAXGARD® 300 | Lycus Ltd. | MAXGARD® 300 is a light yellow powder that is a light stabilizer used for broad-spectrum protection of acrylic adhesives, polyurethane coatings, furniture stains and varnishes, nitrocellulose lacquers, pigments and emulsions from damage caused by UV radia...voir plus MAXGARD® 300 is a light yellow powder that is a light stabilizer used for broad-spectrum protection of acrylic adhesives, polyurethane coatings, furniture stains and varnishes, nitrocellulose lacquers, pigments and emulsions from damage caused by UV radiation. This product has a melting point of 130-132°C and a mass density of 1.34 g/cm3 at 25°C. voir moins | |
| MAXGARD® 400 | Lycus Ltd. | MAXGARD® 400 is an off white powder that is used as an UV stabilizer to protect nitrocellulose lacquers, varnishes, and pressure sensitive acrylic adhesives from UV damage. This product has a melting range of 140-143°C and a mass density of 1.27 g/cm3 at ...voir plus MAXGARD® 400 is an off white powder that is used as an UV stabilizer to protect nitrocellulose lacquers, varnishes, and pressure sensitive acrylic adhesives from UV damage. This product has a melting range of 140-143°C and a mass density of 1.27 g/cm3 at 25°C. voir moins | |
| MAXGARD® 500 | Lycus Ltd. | MAXGARD® 500 is a free flowing light yellow powder that is used as an UV absorber and stabilizer to protect oil-based paints, nitrocellulose lacquers, and varnishes. This product has a melting range of 63-65°C and a mass density of 1.33 g/cm3 at 25°C. | |
| MAXGARD® 600 | Lycus Ltd. | MAXGARD® 600 is a 100% active, pale yellow liquid that is used as an UV stabilizer in industrial coatings, such as polyurethanes, as well as vinyl and acrylic adhesives. This product has a melting range of ~5°C and a mass density of 1.27 g/cm3 at 25°C. | |
| MAXGARD® 700 | Lycus Ltd. | MAXGARD® 700 is a free flowing, light yellow powder that is used primarily in polyurethanes, acrylic coatings, alkyd varnishes and vinyl and acrylic adhesives. It can be used as an UV stabilizer to protect the end product from degradation due to natural s...voir plus MAXGARD® 700 is a free flowing, light yellow powder that is used primarily in polyurethanes, acrylic coatings, alkyd varnishes and vinyl and acrylic adhesives. It can be used as an UV stabilizer to protect the end product from degradation due to natural sunlight. This product has a melting range of 47-49°C and a mass density of 1.16 g/cm3 at 25°C. voir moins | |
| MAXGARD® 900 | Lycus Ltd. | MAXGARD® 900 is a free flowing light yellow powder which can be used as an UV stabilizer. It is very effective for UV protection of oil-based paints, urethane coatings, pressure sensitive acrylic and vinyl adhesives. This product has a melting range of 68...voir plus MAXGARD® 900 is a free flowing light yellow powder which can be used as an UV stabilizer. It is very effective for UV protection of oil-based paints, urethane coatings, pressure sensitive acrylic and vinyl adhesives. This product has a melting range of 68-74°C and a mass density of 1.37 g/cm3 at 25°C. voir moins | |
| MAXGARD® DPA-2 | Lycus Ltd. | MAXGARD® DPA-2 is a white powder designed to provide good heat stability and UV protection with little to no color contribution to the substrate. It can be used as an UV stabilizer in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacq...voir plus MAXGARD® DPA-2 is a white powder designed to provide good heat stability and UV protection with little to no color contribution to the substrate. It can be used as an UV stabilizer in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacquers, and acrylic and vinyl adhesives. This product has a melting point of 93°C and a mass density of 1.16 g/cm3 at 25°C. voir moins | |
| MAXGARD® DPA-8 | Lycus Ltd. | MAXGARD® DPA-8 is a 100% active, clear light amber, viscous liquid stabilizer that has low color and low volatility. It is often used in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacquers, and acrylic and vinyl adhesives. This pro...voir plus MAXGARD® DPA-8 is a 100% active, clear light amber, viscous liquid stabilizer that has low color and low volatility. It is often used in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacquers, and acrylic and vinyl adhesives. This product has a solidification point of 10°C and a mass density of 1.05 g/cm3 at 25°C. voir moins | |
| CAMSIZER® - Dynamic Image Analysis System Particle Size | HORIBA Instruments, Inc. | CAMSIZER® features dynamic image analysis to provide rapid and precise particle size and particle shape distributions for dry powders and bulk material in the size range from 30µm to 30mm. 100% higher resolution. It has a new LED-stroboscope light source ...voir plus CAMSIZER® features dynamic image analysis to provide rapid and precise particle size and particle shape distributions for dry powders and bulk material in the size range from 30µm to 30mm. 100% higher resolution. It has a new LED-stroboscope light source with 20 times higher intensity. It provides extreme depth of sharpness and improved shape and size analysis across the entire measuring range. CAMSIZER® has an optimized, process oriented software, excellent compatibility to sieve analysis it is easy to reproduce and there are several language versions.Typical examples of applications for CAMSIZER® are: Salt/sugar, Sand, Polystyrene, Plastics, Carbon black/coal, Glass/ceramics, Catalysts, Coffee, Fertilisers, Abrasives, Refractory products, Drugs, Carbon products, Foodstuffs and Metal powder. voir moins |  |
| CAMSIZER XT - Dynamic Image Analysis System Particle Size | HORIBA Instruments, Inc. | CAMSIZER XT features dynamic image analysis to provide rapid and precise particle size and particle shape distributions for dry powders and wet dispersions in the size range from 1µm to 3mm. It performs high resolution for narrow, mono-modal distributions...voir plus CAMSIZER XT features dynamic image analysis to provide rapid and precise particle size and particle shape distributions for dry powders and wet dispersions in the size range from 1µm to 3mm. It performs high resolution for narrow, mono-modal distributions, excellent dynamic measurement range for broad distributions or multi-modal samples and reliable detection of smallest amounts (< 0.1 %) of “oversize” particles. It also performs particle shape analysis (e. g. aspect ratio, symmetry or roundness for detection of agglomerates, broken particles or contaminations). CAMSIZER XT is ideal for granules and fine pellets, pulverized and granulated food, detergent powder and raw materials, plastic powders (also with electrostatic charge) metal and ore powders, abrasives (medium-sized and small grit), fine sands and cement, fine wood fibers and fine plastic fibers voir moins |  |
| DT-1201 - Acoustic & Electroacoustic Spectrometer For Particle Size Analysis And Zeta Potential | HORIBA Instruments, Inc. | DT-1201 - Acoustic & Electroacoustic Spectrometer uses acoustic and electroacoustic spectrometry to measure both particle size and zeta potential in very concentrated suspensions (up to 50 vol%) over a size range of 5nm-100µm. Acoustic measurements provid...voir plus DT-1201 - Acoustic & Electroacoustic Spectrometer uses acoustic and electroacoustic spectrometry to measure both particle size and zeta potential in very concentrated suspensions (up to 50 vol%) over a size range of 5nm-100µm. Acoustic measurements provide a wealth of information beyond particle size and zeta potential. For well developed applications, acoustic parameters can be correlated to other product variables. It's advantages over light based techniques include: no dilution needed the sample is measured in native state, it is much less sensitive to contamination, there is no calibration needed, higher precision and wide size range from 5nm to 100 microns. DT-1201 measures sound attenuation and velocity of any fluid like material, gels and milk, for example. voir moins |  |
| LA-300 - Portable Routine Laser Diffraction Analyzer | HORIBA Instruments, Inc. | The LA-300 - Portable Routine Laser Diffraction Analyzer uses Mie Scattering (laser diffraction) to measure particle size of suspensions or dry powders. The speed and ease-of-use of this technique makes it the most popular for many applications. The LA-30...voir plus The LA-300 - Portable Routine Laser Diffraction Analyzer uses Mie Scattering (laser diffraction) to measure particle size of suspensions or dry powders. The speed and ease-of-use of this technique makes it the most popular for many applications. The LA-300's revolutionary size makes it a welcome change to the other large and cumbersome designs. It's real-time displays of particle size distribution and sample concentration let the user check sample at all times. Using a diode laser, the LA-300 measures particles ranging anywhere between 0.1 and 600 μm in diameter with unprecedented precision, and processes high-resolution data for display within 20 seconds. The wide measurable range makes it ideal for application in fundamental studies and quality control of production lines in such diverse fields as pharmaceuticals, fine ceramics, metal powders, polymers, pigments, paints/coatings, adhesives, catalysts, minerals and clays, just to name a few. voir moins |  |
| LA-950 - High Performance Laser Diffraction Analyzer | HORIBA Instruments, Inc. | LA-950 - High Performance Laser Diffraction Analyzer uses an innovative optical system to obtain the world's widest dynamic range of 10 nm – 3000 mm. This makes it possible to perform precise particle size measurements on a wide scale in many different in...voir plus LA-950 - High Performance Laser Diffraction Analyzer uses an innovative optical system to obtain the world's widest dynamic range of 10 nm – 3000 mm. This makes it possible to perform precise particle size measurements on a wide scale in many different industries. From ultra-fine nano-order particles to individually visible particles, all can be measured with this single instrument. Designed to handle the entire range of applications extending from the complex needs of research to routine quality control procedures, the LA-950 offers practicality as a"standard instrument" that is easy to use and enables precise measurement. LA-950 has a wide range of applications including: nano-level research and development, ceramics, pigments, battery materials, catalysts, cosmetics, pharmaceuticals and food products. voir moins |  |
| PSA300 - Static Image Analysis System Particle Size | HORIBA Instruments, Inc. | PSA300 - Static Image Analysis System Particle Size is a state of the art turn-key image analysis solution. Seamless integration of Clemex's powerful particle characterization software and an automated microscope with high resolution camera creates an int...voir plus PSA300 - Static Image Analysis System Particle Size is a state of the art turn-key image analysis solution. Seamless integration of Clemex's powerful particle characterization software and an automated microscope with high resolution camera creates an intuitive, easy-to-use imaging workstation. Analysis of numerous samples from the same batch guarantees significant statistical measurements. Clemex/Horiba PSA300 is the only image analysis system that offers this advantage. Using the microscopy solution allows to: measure different-sized particles in the same run; measure and isolate particles on the basis of shape, color, size and texture; automatically validate the accuracy and precision of measurements; scan large or small areas of one or many samples; customize reports and meet compliance. PSA300 can measure fine and ultra-fine micronized particles of many types of powdered materials. voir moins |  |
| SA-9600 Series Surface Area Analyzers | HORIBA Instruments, Inc. | SA-9600 Series Surface Area Analyzer brings exceptional convenience and confidence to surface area and pore volume analysis. Now you can perform single-point surface area, multi-point surface area and total pore volume measurements with push-button ease. ...voir plus SA-9600 Series Surface Area Analyzer brings exceptional convenience and confidence to surface area and pore volume analysis. Now you can perform single-point surface area, multi-point surface area and total pore volume measurements with push-button ease. It's use of the flowing-gas method allows routine total surface area measurements to be made as quickly as every six minutes, depending on magnitude of surface area. The three-station SA-9603 analyzer measures three samples simultaneously. Because it is fully automated, the SA-9600 series eliminates variables that are sometimes introduced by operator involvement, such as the measurement of nitrogen or movement of the dewer flasks. The SA-9600 provides quick, user friendly specific surface area analysis for a wide variety of powders ranging from catalysts to active pharmaceutical ingredients (API’s). Low surface area API’s and excipients are particularly well suited for analysis by the SA-9600, which provides a quicker measurement time at a lower cost than competitive options. voir moins |  |
| SZ-100 - Nanopartica Series Instruments | HORIBA Instruments, Inc. | SZ-100 - Nanopartica Series Instruments is a highly advanced analyzer solves the mysteries of the nano-world. A single device analyzes the three parameters that characterize nanoparticles: particle diameter, zeta potential, and molecular weight. Advan...voir plus SZ-100 - Nanopartica Series Instruments is a highly advanced analyzer solves the mysteries of the nano-world. A single device analyzes the three parameters that characterize nanoparticles: particle diameter, zeta potential, and molecular weight. Advantages of SZ-100 include sampling measurement using the industry’s lowest sample volume of 100 μL is possible and arithmetic processing from an auto-correlation function by a Fourier transformation to electrical mobility. SZ-100 provides a mean to highly accurate, highly reproducible measurement: electro-osmotic flow countermeasure. Some applications for SZ-100 include biomaterials such as vitamins, enzymes and metals. voir moins |  |
