| 3M™ Ceramic Microspheres W-210 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M c...もっと表示する 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-210 are typically chosen over other 3M ceramic microspheres for higher gloss formulations. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. 表示を減らす | |
| 3M™ Ceramic Microspheres W-410 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler load...もっと表示する 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-410 are typically chosen over other 3M ceramic microspheres for their overall balance in properties. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. 表示を減らす | |
| 3M™ Ceramic Microspheres W-610 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic m...もっと表示する 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-610 are typically chosen over other 3M ceramic microspheres for increased durability. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. 表示を減らす | |
| 3M™ Fluorosurfactant FC-4430 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...もっと表示する 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4430 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product can provide stain and dirt pick up resistance. 表示を減らす | |
| 3M™ Fluorosurfactant FC-4432 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...もっと表示する 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4432 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. 表示を減らす | |
| 3M™ Fluorosurfactant FC-4434 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...もっと表示する 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4434 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. 表示を減らす | |
| 3M™ Glass Bubbles iM16K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...もっと表示する 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles iM30K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...もっと表示する 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K1 | 3M Advanced Materials Division | 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...もっと表示する 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K15 | 3M Advanced Materials Division | 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K20 | 3M Advanced Materials Division | 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K25 | 3M Advanced Materials Division | 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K37 | 3M Advanced Materials Division | 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...もっと表示する 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K42HS | 3M Advanced Materials Division | 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...もっと表示する 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K46 | 3M Advanced Materials Division | 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S15 | 3M Advanced Materials Division | 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S22 | 3M Advanced Materials Division | 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...もっと表示する 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S28HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...もっと表示する 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S32 | 3M Advanced Materials Division | 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S35 | 3M Advanced Materials Division | 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S38 | 3M Advanced Materials Division | 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S38HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush streng...もっと表示する 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S42XHS | 3M Advanced Materials Division | 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...もっと表示する 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S60 | 3M Advanced Materials Division | 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...もっと表示する 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S60HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...もっと表示する 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles XLD3000 | 3M Advanced Materials Division | 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush str...もっと表示する 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Stain Resistant Additive and Sealer SRA-250 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product pe...もっと表示する 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-250 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-250 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. 表示を減らす | |
| 3M™ Stain Resistant Additive and Sealer SRA-270 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The ...もっと表示する 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-270 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-270 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. 表示を減らす | |
| 3M™ Stain Resistant Additive and Sealer SRA-450 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the...もっと表示する 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-450 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-450 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. 表示を減らす | |
| 3M™ Stain Resistant Additive and Sealer SRA-451 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates th...もっと表示する 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-451 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-451 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. 表示を減らす | |
| 3M™ Stain Resistant Additive SRC-220 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product...もっと表示する 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRC-220 offers durability, long-lasting performance and UV resistance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRC-220 is easy to incorporate into existing water and some solvent-based products and can be added to existing formulations or diluted with water or water miscible solvents and used as a stand-alone sealer. 表示を減らす | |
| A-6 Polyamine | Epoxy Chemicals, Inc. | A-6 Polyamine is a straw colored amine curing agent compatible with most aliphatic and cycloaliphatic amine curing agents.This product is intended for use with liquid epoxy resins at room temperature, has virtually no odor, high strength, and has damp adh...もっと表示する A-6 Polyamine is a straw colored amine curing agent compatible with most aliphatic and cycloaliphatic amine curing agents.This product is intended for use with liquid epoxy resins at room temperature, has virtually no odor, high strength, and has damp adhesion properties. It finds application in construction adhesives, hardened concrete adhesives, injection resin, and ASTM 881 resin systems. 表示を減らす | |
| APR Polyamine | Epoxy Chemicals, Inc. | APR Polyamine is a clear liquid that functions as a fast setting amine curing agent with very low viscosity. This product has high strength and can be used as an AEP replacement. It is often used as an accelerator for other curing agents and in adhesives. | |
| Easy Clean Coatings 1000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time...もっと表示する 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. 表示を減らす | |
| Easy Clean Coatings 4000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-4000 is a fluoropolymer used for coating ceramic and glass surfaces. Once it air-dries, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. | |
| Easy Clean Coatings 6000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, he...もっと表示する 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. 表示を減らす | |
| EFB Polyamine | Epoxy Chemicals, Inc. | EFB Polyamine is a light colored cycloaliphatic polyamine with low viscosity, virtually no odor, low benzyl alcohol content, water spot resistance, and blush resistance. This product is designed for use with non-diluted liquid epoxy resin and finds applic...もっと表示する EFB Polyamine is a light colored cycloaliphatic polyamine with low viscosity, virtually no odor, low benzyl alcohol content, water spot resistance, and blush resistance. This product is designed for use with non-diluted liquid epoxy resin and finds application in seamless epoxy flooring, coatings, and chemical resistant coatings. 表示を減らす | |
| FB Polyamine | Epoxy Chemicals, Inc. | FB Polyamine is a light colored cycloaliphatic curing agent with low viscosity, color stability, and water spot, blush, and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use...もっと表示する FB Polyamine is a light colored cycloaliphatic curing agent with low viscosity, color stability, and water spot, blush, and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with bisphenol A epoxy resins, and acrylated/epoxy resins at room temperature. It finds application in color fast tile grouts, chemical resistant coatings, and seamless flooring. 表示を減らす | |
| FB-25 Polyamine | Epoxy Chemicals, Inc. | FB-25 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, color stability, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with...もっと表示する FB-25 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, color stability, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with liquid and solid A epoxy resins. It finds application in high solids coatings, chemical resistant coatings, and seamless flooring. 表示を減らす | |
| FB-30 Polyamine | Epoxy Chemicals, Inc. | FB-30 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, virtually no odor, good color stability, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and ...もっと表示する FB-30 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, virtually no odor, good color stability, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with liquid and solid A epoxy resins. It finds application in chemical resistant coatings and seamless flooring. 表示を減らす | |
| FB-31 Polyamine | Epoxy Chemicals, Inc. | FB-31 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, virtually no odor, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use wi...もっと表示する FB-31 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, virtually no odor, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with liquid and solid A epoxy resins. It finds application in high solids coatings, chemical resistant coatings, and seamless flooring. 表示を減らす | |
| FB-618 Polyamine | Epoxy Chemicals, Inc. | FB-618 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, virtually no odor, good color stability, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and...もっと表示する FB-618 Polyamine is a light colored cycloaliphatic curing agent with low viscosity, virtually no odor, good color stability, and water spot and chemical resistance. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with liquid and solid epoxy resins. It finds application in color fast tile grouts, chemical resistant coatings, and seamless flooring. 表示を減らす | |
| FB-84 Polyamine | Epoxy Chemicals, Inc. | FB-84 Polyamine is a light colored aliphatic curing agent with low viscosity, virtually no odor, high gloss finish, and a long pot life. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with li...もっと表示する FB-84 Polyamine is a light colored aliphatic curing agent with low viscosity, virtually no odor, high gloss finish, and a long pot life. This product is compatible with most aliphatic and cycloaliphatic amine curing agents, and is intended for use with liquid and solid epoxy resins. It finds application in high solids coatings, flooring, and decoupage. 表示を減らす | |
| FS-10 Polyamine | Epoxy Chemicals, Inc. | FS-10 Polyamine is an amine curing agent that does not contain benzyl alcohol, has low viscosity, ultra high strength, and virtually no odor. This product cures at low temperatures and is intended for use with liquid epoxy resins as the primary curative o...もっと表示する FS-10 Polyamine is an amine curing agent that does not contain benzyl alcohol, has low viscosity, ultra high strength, and virtually no odor. This product cures at low temperatures and is intended for use with liquid epoxy resins as the primary curative or a reactive accelerator for existing resin systems. It is suitable for use in epoxy construction adhesives and flooring applications such as construction adhesives, injection resins, seamless trowel flooring, and hardened concrete adhesives. 表示を減らす | |
| FS-1608 Polyamine | Epoxy Chemicals, Inc. | FS-1608 Polyamine is an aliphatic amine adduct with mechanical properties, solvent and alcohol resistance, a fast cure rate, low viscosity, and ultra high strength. This product does not contain nonyl phenol or benzyl alcohol, and can be used as a reactiv...もっと表示する FS-1608 Polyamine is an aliphatic amine adduct with mechanical properties, solvent and alcohol resistance, a fast cure rate, low viscosity, and ultra high strength. This product does not contain nonyl phenol or benzyl alcohol, and can be used as a reactive accelerator with most amine curing agents for thermoset applications. It is used in construction adhesives, flooring, mortars, laminates, and low VOC coatings. 表示を減らす | |
| FS-289 Polyamine | Epoxy Chemicals, Inc. | FS-289 Polyamine is an aliphatic polyamine that does not contain benzyl alcohol, has virtually no odor, low viscosity, high strength, and excellent damp adhesion. This product demonstrates thin film development, cures at low temperatures, and can be used ...もっと表示する FS-289 Polyamine is an aliphatic polyamine that does not contain benzyl alcohol, has virtually no odor, low viscosity, high strength, and excellent damp adhesion. This product demonstrates thin film development, cures at low temperatures, and can be used to accelerate other hardener systems to improve thin film cure. It is suitable for use in construction adhesives, injection resins, accelerated flooring systems, and hardened concrete adhesives. 表示を減らす | |
| FS-290 Polyamine | Epoxy Chemicals, Inc. | FS-290 Polyamine is a modified polyamine that does not contain benzyl alcohol, nonyl phenol, or TMD, and has high strength and damp adhesion. This product demonstrates thin film development at low temperatures, and can be used to accelerate other hardener...もっと表示する FS-290 Polyamine is a modified polyamine that does not contain benzyl alcohol, nonyl phenol, or TMD, and has high strength and damp adhesion. This product demonstrates thin film development at low temperatures, and can be used to accelerate other hardener systems to improve thin film cure. It functions as a curing agent for liquid epoxy resins, and finds application in construction adhesives, solvent free high solids coatings, crack injection resins, accelerate flooring systems, and hardened concrete adhesives. 表示を減らす | |
| FS-43 Polyamine | Epoxy Chemicals, Inc. | FS-43 Polyamine is a fast setting amine curing agent that does not contain benzyl alcohol, has virtually no odor, and damp adhesion. This product consists of 100% solids, exhibits rapid cure with low yellowing characteristics, and can be used as a reactiv...もっと表示する FS-43 Polyamine is a fast setting amine curing agent that does not contain benzyl alcohol, has virtually no odor, and damp adhesion. This product consists of 100% solids, exhibits rapid cure with low yellowing characteristics, and can be used as a reactive accelerator for polyamide, amidoamine, and cycloaliphatic amine curing agents. It is suitable for use in construction adhesives, injection resins, and hardened concrete adhesives. 表示を減らす | |
| FS-56 Polyamine | Epoxy Chemicals, Inc. | FS-56 Polyamine is an accelerated hardener that does not contain benzyl alcohol, has no mercaptans, low viscosity, and ultra high strength. This product cures at low temperatures and is intended for use with liquid epoxy resins as the primary curative or ...もっと表示する FS-56 Polyamine is an accelerated hardener that does not contain benzyl alcohol, has no mercaptans, low viscosity, and ultra high strength. This product cures at low temperatures and is intended for use with liquid epoxy resins as the primary curative or a reactive accelerator for existing resin systems. It is suitable for use in construction adhesives, injection resins, seamless flooring, and hardened concrete adhesives. 表示を減らす | |
| FS-943 Polyamine | Epoxy Chemicals, Inc. | FS-943 Polyamine is an aliphatic amine adduct with mechanical properties, solvent and alcohol resistance, a fast cure rate, low viscosity, and ultra high strength. This product does not contain nonyl phenol or benzyl alcohol, and can be used as a reactive...もっと表示する FS-943 Polyamine is an aliphatic amine adduct with mechanical properties, solvent and alcohol resistance, a fast cure rate, low viscosity, and ultra high strength. This product does not contain nonyl phenol or benzyl alcohol, and can be used as a reactive accelerator with most amine curing agents for thermoset applications. It is used in construction adhesives, flooring, mortars, laminates, and low VOC coatings. 表示を減らす | |
| HCR 280 Polyamine | Epoxy Chemicals, Inc. | HCR 280 Polyamine is a high performance PACM based cycloaliphatic curing agent for use with liquid epoxy resins. This product cures at low temperatures and has chemical, water spot, and amine blush resistance. It is phenol free and DOT non-corrosive, and ...もっと表示する HCR 280 Polyamine is a high performance PACM based cycloaliphatic curing agent for use with liquid epoxy resins. This product cures at low temperatures and has chemical, water spot, and amine blush resistance. It is phenol free and DOT non-corrosive, and can find application in industrial flooring, high-solids coatings, chemical resistant linings and mortars, and secondary containment linings. 表示を減らす | |
| HCR Polyamine | Epoxy Chemicals, Inc. | HCR Polyamine is a low viscosity cycloaliphatic polyamine blend designed for high chemical resistance. This product can be combined with liquid epoxy resins or epoxy novolac resin, it has low odor and long working life. | |
| LM Polyamine | Epoxy Chemicals, Inc. | LM Polyamine is an amine curing agent suited for use in epoxy construction adhesives for low modulus properties. This product is intended for use with liquid epoxy resins at room temperature, and has strong adhesion to concrete. It finds application in ep...もっと表示する LM Polyamine is an amine curing agent suited for use in epoxy construction adhesives for low modulus properties. This product is intended for use with liquid epoxy resins at room temperature, and has strong adhesion to concrete. It finds application in epoxy overlays for non-skid surfaces, ASTM 881, type III resin systems, and DOT epoxies. 表示を減らす | |
| UW Polyamine | Epoxy Chemicals, Inc. | UW Polyamine is an amine curing agent suited for use in under water applications. This product has hydrophobic molecules which react into the backbone to impart damp and underwater adhesion. It finds application in splash zone compounds and coatings, pile...もっと表示する UW Polyamine is an amine curing agent suited for use in under water applications. This product has hydrophobic molecules which react into the backbone to impart damp and underwater adhesion. It finds application in splash zone compounds and coatings, pile grout, underwater injection mortars, and DOT epoxies. 表示を減らす | |
| UWL Polyamine | Epoxy Chemicals, Inc. | UWL Polyamine is an amine curing agent suited for use in underwater or damp applications. This product combines hydrophobic nature of the hardener with long working life. It can be used to improve damp adhesion for existing coating or flooring systems, it...もっと表示する UWL Polyamine is an amine curing agent suited for use in underwater or damp applications. This product combines hydrophobic nature of the hardener with long working life. It can be used to improve damp adhesion for existing coating or flooring systems, it can also find application in splash zone compounds, pile grout resins, underwater injection resins, underwater coatings, and grouts and mortars. 表示を減らす |
