| BLUESIL ADD 10086 | Elkem Silicones | BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints ...Vea Mas BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints and silicone binders. Vea Menos | |
| BLUESIL ADD 11013 | Elkem Silicones | BLUESIL ADD 11013 is a polyether-modified polydimethylsiloxane for use in solventless paints and varnishes, and in water-based paints and inks. | |
| BLUESIL BP 9200 | Elkem Silicones | BLUESIL BP 9200 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9300 | Elkem Silicones | BLUESIL BP 9300 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9705 | Elkem Silicones | BLUESIL BP 9705 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL BP 9710 | Elkem Silicones | BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and...Vea Mas BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and it does not contain ecotoxic surfactant. After it has dried on the surface, BLUESIL BP 9710 repels water and allows walls to breathe. Experience acquired over more than 40 years shows that silicone water repellents are a good answer to humidity problems in construction materials, particularly when for esthetical reasons the natural aspect of the material should be preserved. BLUESIL BP 9710 has been awarded a test certificate by CSTC (Centre Scientifique et Technique de - ): ref HD-340/133-151 on the 2006.02.20. Vea Menos | |
| BLUESIL BP 9800 | Elkem Silicones | BLUESIL BP 9800 is an aqueous APE-free polymethylsiloxane resin emulsion. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9821 | Elkem Silicones | BLUESIL BP 9821 is an aqueous APE-free polymethylsiloxane resin emulsion with low VOC content. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9878 | Elkem Silicones | BLUESIL BP 9878 is an aqueous polymethylsiloxane resin emulsion.This emulsion provides two fundamental properties of the silicone technology to the paint film: water repellency and permeability to water vapour. | |
| BLUESIL BP 9900 | Elkem Silicones | BLUESIL BP 9900 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive for building materials. | |
| BLUESIL BP 9920 | Elkem Silicones | BLUESIL BP 9920is anon-ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL EMUL 1803 | Elkem Silicones | BLUESIL EMUL 1803 is a non-ionic silicone emulsion containing silicone oil and resin. This emulsion is intended for mould-release of cast polyurethane elastomers. | |
| BLUESIL EMUL 269 | Elkem Silicones | BLUESIL EMUL 269 is an aqueous emulsion of an hydrogeno polysiloxane. | |
| BLUESIL EMUL 284 | Elkem Silicones | BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening prop...Vea Mas BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening properties (textile applications). Vea Menos | |
| BLUESIL EMUL 3500 | Elkem Silicones | BLUESIL EMUL 3500 is a general purpose; non-ionic oil in water silicone emulsion, of a high viscosity hydroxyl terminated polysiloxane. | |
| BLUESIL EMUL 35B | Elkem Silicones | BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream...Vea Mas BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream, neither during storage nor in use.Perfect stability in contact with hard water or zinc (i.e. in galvanized metal containers).Excellent heat stability after dilution.Very good wetting power. Vea Menos | |
| BLUESIL EMUL 55 | Elkem Silicones | BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component...Vea Mas BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component elements making up polishes and cleaners for artificial leather fabrics (PVC, PUR) and furniture polishes. Vea Menos | |
| BLUESIL EMUL 872 | Elkem Silicones | BLUESIL EMUL 872 is a slightly anionic aqueous emulsion with a 60% dry content, for general purposes. This is a concentrated version of BLUESIL EMUL E1P. | |
| BLUESIL EMUL E1P | Elkem Silicones | BLUESIL EMUL E1P is an oil in water emulsion containing 35 % of a silicone oil. It can be used in many industries. | |
| BLUESIL EMUL E1P U1 | Elkem Silicones | BLUESIL EMUL E1P U1 is a general purpose, non-ionic, aqueous silicone emulsion. | |
| BLUESIL EMULSION 2400 | Elkem Silicones | BLUESIL EMUL 2400 is a general purpose; non-ionic oil in water silicone emulsion of a methyl-hydrogen polysiloxane. | |
| BLUESIL FLD 21625 | Elkem Silicones | BLUESIL FLD 21625is anα/ω-epoxy functionalised polydimethylsiloxane fluid. | |
| BLUESIL FLD 45 | Elkem Silicones | BLUESIL FLD 45 is a low viscosity dimethylpolysiloxane oil used to prevent floating and flooding and improve leveling of air-drying paints. | |
| BLUESIL FLD 47V1 000 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V100 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V350 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V50 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V500 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL PI 2074 | Elkem Silicones | BLUESIL PI 2074 is a cationic photoinitiator for use with epoxy resins, vinyl ethers or any other type of oligomer which polymerises cationically. It is also suited to the formulation of hybrid radical / cationic systems. | |
| BLUESIL RES 6405 | Elkem Silicones | BLUESIL RES 6405 is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6405X | Elkem Silicones | BLUESIL RES 6405X is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6406XM | Elkem Silicones | BLUESIL RES 6406XM is a 60% solids methylphenylsilicone resin in Xylene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6407 | Elkem Silicones | BLUESIL RES 6407 is a 70% solids methylphenylsilicone resin in Toluene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6482X | Elkem Silicones | BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It i...Vea Mas BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It is also more compatible than other silicones with urea-formaldehyde, melamine-formaldehyde, epoxy, polyurethane and acrylic resins. Another use is as an additive for epoxy paints. It also improves weathering resistance. Vea Menos | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL TCS 7001 | Elkem Silicones | BLUESIL TCS 7001 is an alkyl polysiloxane solution in solvent phase specifically developed for the waterproofing of fabrics and leathers exposed to difficult weather conditions by spraying or impregnating. | |
| CAF 2534 | Elkem Silicones | CAF 2534 is a one component silicone rubber that cures when in contact with air humidity. It is intended for use as a formulation base for the development of tie-coats in the fouling release treatment of boat hulls. | |
| LYNDCOAT 15 RTU | Elkem Silicones | LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RT...Vea Mas LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RTU also helps keep molds and vents clean, reducing defects and downtime. Lyndcoat™ 15 RTU typically is durable through multiple production cycles. The need for reapplication is dependent on factors such as the rubber compound, curing time, curing temperature, tread design and application technique. Lyndcoat™ 15 RTU is designed for processes requiring low viscosity mold lubricants. Vea Menos | |
| LYNDCOAT BR 1100 RTU | Elkem Silicones | LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the c...Vea Mas LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1100 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1100 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as Lyndcoat™ BR2101 RTU is highly recommended. Vea Menos | |
| LYNDCOAT BR 1102 | Elkem Silicones | LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the c...Vea Mas LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1102 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1102 RTU is of medium viscosity and does not contain mica. Vea Menos | |
| LYNDCOAT BR 1103 RTU | Elkem Silicones | LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the c...Vea Mas LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR1103 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. LYNDCOAT® BR1103 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as LYNDCOAT® BR2201 RTU is highly recommended. Vea Menos | |
| LYNDCOAT BR 1110 RTU | Elkem Silicones | LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers ...Vea Mas LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. LYNDCOAT BR 1110 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. LYNDCOAT BR 1110 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as LYNDCOAT BR 2101 RTU, is highly recommended. Vea Menos | |
| LYNDCOAT BR 1211 | Elkem Silicones | LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtim...Vea Mas LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtimes. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. Vea Menos | |
| LYNDCOAT BR 1214 | Elkem Silicones | LYNDCOAT BR 1214 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It is particularly friction resistant and slip promoting. Applied on the inside of the green...Vea Mas LYNDCOAT BR 1214 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It is particularly friction resistant and slip promoting. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. Vea Menos | |
| LYNDCOAT BR 1623 RTU | Elkem Silicones | LYNDCOAT BR 1623 RTU is a ready to use, silicone based, medium mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coatin...Vea Mas LYNDCOAT BR 1623 RTU is a ready to use, silicone based, medium mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. Lyndcoat BR 1623 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. Lyndcoat BR 1623 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as Lyndcoat XR 3900 Primer, is highly recommended. Vea Menos | |
| LYNDCOAT BR 1812 | Elkem Silicones | LYNDCOAT BR 1812 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR 1812 RTU replace...Vea Mas LYNDCOAT BR 1812 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR 1812 RTU replaces the conventional lining cements and solvent-based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR 1812 RTU does not contain aromatic or chlorinated solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR 1812 RTU is of low viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. Vea Menos | |
| LYNDCOAT BR 2100 RTU | Elkem Silicones | LYNDCOAT BR 2100 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures durable performance. | |
| LYNDCOAT BR 2104 | Elkem Silicones | LYNDCOAT BR 2104 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a long lasting multi release and slip performance. It was designed to...Vea Mas LYNDCOAT BR 2104 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a long lasting multi release and slip performance. It was designed to reduce build up notably in the bead area. Vea Menos | |
| LYNDCOAT BR 2201 | Elkem Silicones | LYNDCOAT BR 2201 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR 2201 replaces t...Vea Mas LYNDCOAT BR 2201 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR 2201 replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR 2201 does not contain aromatic or chlorinated solvents. It is easy to use and can be brushed, swabbed, or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. LYNDCOAT® BR 2201 is of high viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. Vea Menos | |
| LYNDCOAT BR 2204 A1 | Elkem Silicones | LYNDCOAT BR 2204 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build...Vea Mas LYNDCOAT BR 2204 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build up notably in the bead area. Vea Menos | |
| LYNDCOAT BR 2204 E4 | Elkem Silicones | LYNDCOAT BR 2204 E4 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce b...Vea Mas LYNDCOAT BR 2204 E4 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build up notably in the bead area. Vea Menos | |
| LYNDCOAT BR 2511 RTU | Elkem Silicones | LYNDCOAT BR2511 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines long lasting multi release with excellent slip and exceptional air bleed performan...Vea Mas LYNDCOAT BR2511 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines long lasting multi release with excellent slip and exceptional air bleed performance. Vea Menos | |
| LYNDCOAT BR 2512 | Elkem Silicones | LYNDCOAT BR2512 is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines particularly long lasting multi release and slip with exceptional air bleed performanc...Vea Mas LYNDCOAT BR2512 is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines particularly long lasting multi release and slip with exceptional air bleed performance. Vea Menos | |
| LYNDCOAT BR 601 RTU | Elkem Silicones | LYNDCOAT BR-601 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-601 RTU rep...Vea Mas LYNDCOAT BR-601 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-601 RTU replaces the conventional lining cements and solvent-based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR-601 RTU does not contain any solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR-601 RTU is of medium viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. Vea Menos | |
| LYNDCOAT BR 790 RTU | Elkem Silicones | LYNDCOAT BR 790 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-790 RTU rep...Vea Mas LYNDCOAT BR 790 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-790 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR-790 RTU does not contain any solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR-790 RTU is of low viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. Vea Menos | |
| LYNDCOAT MR 5100 RTU | Elkem Silicones | LYNDCOAT MR 5100 RTU is a ready to use, solvent free, water based coating designed for use in tire moulds. It is a blend of polymers that cure at typical molding temperatures to form a clear, tough, coating with a strong bond to the metal mould, possessin...Vea Mas LYNDCOAT MR 5100 RTU is a ready to use, solvent free, water based coating designed for use in tire moulds. It is a blend of polymers that cure at typical molding temperatures to form a clear, tough, coating with a strong bond to the metal mould, possessing excellent release and lubrication properties towards rubber. LYNDCOAT MR 5100 RTU helps keep moulds and vents clean, which reduces defects and downtime. LYNDCOAT MR 5100 RTU is durable through multiple production cycles. The need for reapplication is dependent on factors such as: the rubber compound, tread design, curing time, curing temperature, application technique and press type. LYNDCOAT MR 5100 RTU is designed for processes requiring low viscosity mould lubricants. Vea Menos | |
| SILBIONE CAF 72576 RED | Elkem Silicones | SILBIONE CAF 72576 RED is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 a...Vea Mas SILBIONE CAF 72576 RED is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. Vea Menos | |
| SILBIONE CAF 72589 | Elkem Silicones | SILBIONE CAF 72589 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat natural or agglomerated bottle corks. SILBIONE CAF 72589 is a solventless product based on reactive polymethyl siloxan...Vea Mas SILBIONE CAF 72589 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat natural or agglomerated bottle corks. SILBIONE CAF 72589 is a solventless product based on reactive polymethyl siloxane oils and inert fillers. It can be used as a release coating for materials intended for food contact. Vea Menos | |
| SILBIONE DISPERSION CAF 70004 | Elkem Silicones | SILBIONE DISPERSION CAF 70004 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat agglomerated bottle corks and especially champagne corks. SILBIONE DISPERSION CAF 70004 is a product based ...Vea Mas SILBIONE DISPERSION CAF 70004 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat agglomerated bottle corks and especially champagne corks. SILBIONE DISPERSION CAF 70004 is a product based on reactive polymethyl siloxane oils and inert fillers. It can be used as a release coating for materials intended for food contact. Vea Menos | |
| SILBIONE DISPERSION CAF 71500 GRY | Elkem Silicones | SILBIONE DISPERSION CAF 71500 GRY is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS ...Vea Mas SILBIONE DISPERSION CAF 71500 GRY is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. Vea Menos | |
| SILBIONE DISPERSION CAF 71528 | Elkem Silicones | SILBIONE DISPERSION CAF 71528 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF ...Vea Mas SILBIONE DISPERSION CAF 71528 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. Vea Menos | |
| SILBIONE DISPERSION CAF 71550 | Elkem Silicones | SILBIONE DISPERSION CAF 71550 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF ...Vea Mas SILBIONE DISPERSION CAF 71550 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. Vea Menos | |
| SILBIONE RES 76405 | Elkem Silicones | SILBIONE RESINE 76405 is a polymethylphenyl-siloxane resin supplied as 50% solution in toluene. SILBIONE RESINE 76405 is used as release coating for materials that will be in contact with foodstuff. This resin can also be used as a binder in paints develo...Vea Mas SILBIONE RESINE 76405 is a polymethylphenyl-siloxane resin supplied as 50% solution in toluene. SILBIONE RESINE 76405 is used as release coating for materials that will be in contact with foodstuff. This resin can also be used as a binder in paints developed to protect and decorate these materials. The products obtained after crosslinking of SILBIONE RESINE 76405 contain only substances permitted by the Food Contact regulations currently in force. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coatings obtained have been correctly applied, in particular to avoid any risk of migration of constituents. Vea Menos | |
| SILCOLAPSE 120 | Elkem Silicones | SILCOLAPSE 120 is a 100% active compound containing polydimethylsiloxane oil and silica with an excellent behaviour in a large range of pH. SILCOLAPSE 120 is mainly intended for treatment of organic and anhydrous foaming systems. It can also be used in aq...Vea Mas SILCOLAPSE 120 is a 100% active compound containing polydimethylsiloxane oil and silica with an excellent behaviour in a large range of pH. SILCOLAPSE 120 is mainly intended for treatment of organic and anhydrous foaming systems. It can also be used in aqueous medium. SILCOLAPSE 120 is designed exclusively for industrial use. Vea Menos | |
| SILCOLAPSE 416 | Elkem Silicones | SILCOLAPSE 416 is a compound based on polydimethyl siloxane oil and silica. It has the characteristic of being easy to disperse in most foaming mediums. | |
| SILCOLAPSE 426R | Elkem Silicones | SILCOLAPSE 426R is a non-ionic aqueous emulsion based on polydimethylsiloxane oil. It has 30% active matter content and is recommended for the prevention, control or elimination of foam in aqueous systems. | |
| SILCOLAPSE 495 | Elkem Silicones | SILCOLAPSE 495 is a high performance silicone antifoam emulsion designed for use in a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm solids, even at elevated temperatures and under ...Vea Mas SILCOLAPSE 495 is a high performance silicone antifoam emulsion designed for use in a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm solids, even at elevated temperatures and under pressure. SILCOLAPSE 495 gives good results at wide-ranging pH and is effective under highly alkaline or acidic conditions. Vea Menos | |
| SILCOLAPSE 496 | Elkem Silicones | SILCOLAPSE 496 is a high performance silicone antifoam emulsion designed for use in severe environmental storage conditions and a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm soli...Vea Mas SILCOLAPSE 496 is a high performance silicone antifoam emulsion designed for use in severe environmental storage conditions and a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm solids, even at elevated temperatures and under pressure. SILCOLAPSE 496 gives good results at wideranging pH and is effective under highly alkaline or acidic conditions. The emulsion is freezeprotected to less than -10°C and is stable upon thawing even after repeated freeze thaw cycles below -40°C Vea Menos | |
| SILCOLAPSE 5020 | Elkem Silicones | SILCOLAPSE 5020 is a non-ionic aqueous emulsion containing dimethylpolysiloxane, and is highly effective for prevention, control and elimination of foam in aqueous media. SILCOLAPSE 5020 contains 20% of active ingredient and is designed for industrial use...Vea Mas SILCOLAPSE 5020 is a non-ionic aqueous emulsion containing dimethylpolysiloxane, and is highly effective for prevention, control and elimination of foam in aqueous media. SILCOLAPSE 5020 contains 20% of active ingredient and is designed for industrial uses. Other specialized defoaming agents exist for use in food contact please consult us about them. Vea Menos | |
| SILCOLAPSE C525 | Elkem Silicones | SILCOLAPSE C525 is a silicone antifoam emulsion with very good water dispersibility and antifoaming efficiency in different aqueous systems. It shows very good stability with side range of pH value. | |
| SILCOLEASE 7611 | Elkem Silicones | SILCOLEASE 7611 is a kind of tri-component solventless type paper release system:Silcolease 7611 (base polymer)Silcolease crosslinker 321(crosslinker)Silcolease catalyst 91B (catalyst). | |
| SILCOLEASE ADD 107 | Elkem Silicones | SILCOLEASE ADD 107 is a silicone based additive used with a reactive solvent based silicone polymer system used for release coating of papers, films and various substrates. It has been especially designed to give excellent long term anchorage of the relea...Vea Mas SILCOLEASE ADD 107 is a silicone based additive used with a reactive solvent based silicone polymer system used for release coating of papers, films and various substrates. It has been especially designed to give excellent long term anchorage of the release system on PET film both when laminated against adhesives and reeled as coated film. Vea Menos | |
| SILCOLEASE ADD 382 | Elkem Silicones | SILCOLEASE ADD 382 is a silicone based additive used with a reactive solventless silicone polymer system for POLYESTER (PET) FILM RELEASE COATING applications. | |
| SILCOLEASE ADD 702 | Elkem Silicones | SILCOLEASE ADD 702 is a white, granular powder, freely soluble in water and possessing a slight odour of ammonia. It is used with emulsion SILCOLEASE polyaddition or polycondensation release systems to improve hold-out of the silicone. | |
| SILCOLEASE CATA 11091 M | Elkem Silicones | SILCOLEASE CATALYST 11091 M is a platinum complex mainly used as a catalyst of the solventless SILCOLEASE release systems. | |
| SILCOLEASE CATA 12070 | Elkem Silicones | SILCOLEASE CATALYST 12070 is a platinum complex mainly used as a catalyst of the solventless SILCOLEASE release systems. | |
| SILCOLEASE CATA 340 | Elkem Silicones | SILCOLEASE CATA 340 is a platinum catalyst for use with polyaddition solventless release coatings. This catalyst consists of a platinum complex dispersed with a mist-reducing additive and is designed to catalyze release systems that will be coated at high...Vea Mas SILCOLEASE CATA 340 is a platinum catalyst for use with polyaddition solventless release coatings. This catalyst consists of a platinum complex dispersed with a mist-reducing additive and is designed to catalyze release systems that will be coated at high speeds. Vea Menos | |
| SILCOLEASE CATA 62 A | Elkem Silicones | SILCOLEASE CATALYST 62 A is an organosilicic complex diluted in an aliphatic solvent. It is the catalyst used for the solvent based SILCOLEASE 429 system intended for RELEASE COATING of paper, films and various substrates, with the exception of food conta...Vea Mas SILCOLEASE CATALYST 62 A is an organosilicic complex diluted in an aliphatic solvent. It is the catalyst used for the solvent based SILCOLEASE 429 system intended for RELEASE COATING of paper, films and various substrates, with the exception of food contact application. Vea Menos | |
| SILCOLEASE CATA 62 B | Elkem Silicones | SILCOLEASE CATALYST 62 B is an organometallic complex diluted in an aromatic solvent. It is used as catalyst for the solvent based SILCOLEASE 429 system intended for RELEASE COATING of paper, films and various substrates, except for food contact applicati...Vea Mas SILCOLEASE CATALYST 62 B is an organometallic complex diluted in an aromatic solvent. It is used as catalyst for the solvent based SILCOLEASE 429 system intended for RELEASE COATING of paper, films and various substrates, except for food contact applications. Vea Menos | |
| SILCOLEASE CATA 90 B | Elkem Silicones | SILCOLEASE CATALYST 90 B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems, such as SILCOLEASE 7420 and 7410, intended for RELEASE COATING of paper, films and various substrates. SILCOLEASE CATALY...Vea Mas SILCOLEASE CATALYST 90 B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems, such as SILCOLEASE 7420 and 7410, intended for RELEASE COATING of paper, films and various substrates. SILCOLEASE CATALYST 90 B is used solely in polyaddition reaction systems. Vea Menos | |
| SILCOLEASE CATA 91 B | Elkem Silicones | SILCOLEASE CATALYST 91B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems intended for release coating of paper, film and various substrates: SILCOLEASE 7410 SERIES. SILCOLEASE CATALYST 91B is use...Vea Mas SILCOLEASE CATALYST 91B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems intended for release coating of paper, film and various substrates: SILCOLEASE 7410 SERIES. SILCOLEASE CATALYST 91B is used in polyaddition reaction only. The release properties of the coating can be modified. Vea Menos | |
| SILCOLEASE CATA 93 B | Elkem Silicones | SILCOLEASE CATALYST 93 B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems, such as SILCOLEASE 7440, intended for release coating of paper, films and various substrates. SILCOLEASE CATALYST 93 B i...Vea Mas SILCOLEASE CATALYST 93 B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems, such as SILCOLEASE 7440, intended for release coating of paper, films and various substrates. SILCOLEASE CATALYST 93 B is used solely in polyaddition reaction systems. Vea Menos | |
| SILCOLEASE CATA 94 B | Elkem Silicones | SILCOLEASE CATALYST 94B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems intended for RELEASE COATING of paper, film and various substrates: SILCOLEASE 7450. SILCOLEASE CATALYST 94B is used in po...Vea Mas SILCOLEASE CATALYST 94B is a platinum complex diluted in a solvent. It is the catalyst used for the solvent based SILCOLEASE systems intended for RELEASE COATING of paper, film and various substrates: SILCOLEASE 7450. SILCOLEASE CATALYST 94B is used in polyaddition reaction only. The release properties of the coating can be modified. Vea Menos | |
| SILCOLEASE EMUL RCA 954 | Elkem Silicones | SILCOLEASE EMULSION RCA 954 is a non ionic aqueous emulsion. It is used as a tight release additive in emulsion paper coating applications and serves to increase the peeling force required to separate the pressure sensitive adhesive from the siliconised r...Vea Mas SILCOLEASE EMULSION RCA 954 is a non ionic aqueous emulsion. It is used as a tight release additive in emulsion paper coating applications and serves to increase the peeling force required to separate the pressure sensitive adhesive from the siliconised release liner. This RCA emulsion is used as a RCA in polyaddition type emulsions in the SILCOLEASE range. Vea Menos | |
| SILCOLEASE EMULSION 70840 | Elkem Silicones | SILCOLEASE EMULSION 70840 is a SILICONE EMULSION intended for the RELEASE COATING OF PAPERS and various other substrates, except papers used for food contact. SILCOLEASE EMULSION 70840 cures by a polycondensation reaction in the presence of an organic tin...Vea Mas SILCOLEASE EMULSION 70840 is a SILICONE EMULSION intended for the RELEASE COATING OF PAPERS and various other substrates, except papers used for food contact. SILCOLEASE EMULSION 70840 cures by a polycondensation reaction in the presence of an organic tin compound forming an ELASTOMERIC COATING. Vea Menos | |
| SILCOLEASE EMULSION 902 | Elkem Silicones | SILCOLEASE EMULSION 902 is a SILICONE EMULSION intended for the RELEASE COATING OF PAPERS and various other substrates. SILCOLEASE EMULSION 902 cures by a polyaddition reaction in the presence of an organometallic compound forming an ELASTOMERIC COATING. ...Vea Mas SILCOLEASE EMULSION 902 is a SILICONE EMULSION intended for the RELEASE COATING OF PAPERS and various other substrates. SILCOLEASE EMULSION 902 cures by a polyaddition reaction in the presence of an organometallic compound forming an ELASTOMERIC COATING. The release properties of the coatings can be modified as required. Vea Menos | |
| SILCOLEASE EMULSION 907 | Elkem Silicones | SILCOLEASE EMULSION 907 is a SILICONE EMULSION and is used as the base polymer in a three part formulation intended for the RELEASE COATING OF PAPERS, and various other substrates. SILCOLEASE EMULSION 907 cures by a polyaddition reaction in the presence o...Vea Mas SILCOLEASE EMULSION 907 is a SILICONE EMULSION and is used as the base polymer in a three part formulation intended for the RELEASE COATING OF PAPERS, and various other substrates. SILCOLEASE EMULSION 907 cures by a polyaddition reaction in the presence of suitable emulsions of crosslinker and an organometallic catalyst, for example (e.g. SILCOLEASE EMULSION XL 969 and SILCOLEASE EMULSION CATA 903) to give an ELASTOMERIC type coating. It may be used to coat substrates that meet “food contact application” requirements. Vea Menos | |
| SILCOLEASE EMULSION 908 | Elkem Silicones | SILCOLEASE EMULSION 908 is a SILICONE EMULSION intended for the RELEASE COATING OF PAPERS and various other substrates. SILCOLEASE EMULSION 908 cures by a polyaddition reaction in the presence of an organometallic catalyst, for example SILCOLEASE EMULSION...Vea Mas SILCOLEASE EMULSION 908 is a SILICONE EMULSION intended for the RELEASE COATING OF PAPERS and various other substrates. SILCOLEASE EMULSION 908 cures by a polyaddition reaction in the presence of an organometallic catalyst, for example SILCOLEASE EMULSION CATALYST 903, producing an ELASTOMERIC COATING. The release properties of the coatings can be modified as required. Vea Menos | |
| SILCOLEASE EMULSION 912 | Elkem Silicones | SILCOLEASE EMULSION 912 is a silicone emulsion intended for the release coating of papers and various other substrates. SILCOLEASE EMULSION 912 cures by a polyaddition reaction in the presence of an organometallic catalyst, for example SILCOLEASE EMULSION...Vea Mas SILCOLEASE EMULSION 912 is a silicone emulsion intended for the release coating of papers and various other substrates. SILCOLEASE EMULSION 912 cures by a polyaddition reaction in the presence of an organometallic catalyst, for example SILCOLEASE EMULSION CATALYST 913 producing an elastomeric coating. The release properties of the coatings can be modified as required. Vea Menos | |
| SILCOLEASE EMULSION 915 | Elkem Silicones | SILCOLEASE EMULSION 915 is a silicone emulsion intended for the release coating of papers and various other substrates. SILCOLEASE EMULSION 915 cures by a polyaddition reaction in the presence of an organometallic compound forming an elastomeric coating. ...Vea Mas SILCOLEASE EMULSION 915 is a silicone emulsion intended for the release coating of papers and various other substrates. SILCOLEASE EMULSION 915 cures by a polyaddition reaction in the presence of an organometallic compound forming an elastomeric coating. The release properties of the coatings can be modified as required. Vea Menos | |
| SILCOLEASE EMULSION 925 | Elkem Silicones | SILCOLEASE EMUL 925 is a silicone emulsion intended for the release coating of papers and various other substrates. SILCOLEASE EMUL 925 cures by a polyaddition reaction in the presence of an organometallic catalyst, for example SILCOLEASE EMULSION CATALYS...Vea Mas SILCOLEASE EMUL 925 is a silicone emulsion intended for the release coating of papers and various other substrates. SILCOLEASE EMUL 925 cures by a polyaddition reaction in the presence of an organometallic catalyst, for example SILCOLEASE EMULSION CATALYST 903, producing an elastomeric coating. The release properties of the coatings can be modified as required. Vea Menos | |
| SILCOLEASE EMULSION CATA 70827 A | Elkem Silicones | SILCOLEASE EMULSION CATALYST 70827 A is an organic tin compound emulsion. It is the EMULSION CATALYST of silicone emulsions intended for the RELEASE COATING OF PAPERS and various other substrates, - except for substrates used for food contact -e.g. SILCOL...Vea Mas SILCOLEASE EMULSION CATALYST 70827 A is an organic tin compound emulsion. It is the EMULSION CATALYST of silicone emulsions intended for the RELEASE COATING OF PAPERS and various other substrates, - except for substrates used for food contact -e.g. SILCOLEASE EMULSION 70840. It only catalyses polycondensation type reactions. Vea Menos | |
| SILCOLEASE EMULSION CATA 903 | Elkem Silicones | SILCOLEASE EMULSION CATALYST 903 is an emulsion of reactive silicone polymers combined with an organometallic catalyst. It is an EMULSION CATALYST to be used in conjunction with a silicone emulsion intended for RELEASE COATING OF PAPERS and various substr...Vea Mas SILCOLEASE EMULSION CATALYST 903 is an emulsion of reactive silicone polymers combined with an organometallic catalyst. It is an EMULSION CATALYST to be used in conjunction with a silicone emulsion intended for RELEASE COATING OF PAPERS and various substrates, for example SILCOLEASE EMULSION 908. It is recommended uniquely for the catalysis of polyaddition type reactions. Vea Menos | |
| SILCOLEASE EMULSION CATA 909 | Elkem Silicones | SILCOLEASE EMULSION CATA 909 a non-ionic aqueous emulsion of polymethylsiloxane grafted with reactive chemicals with the addition of a Platinum salt. It is used as an emulsion catalyst for the range of SILCOLEASE EMULSIONS to obtain a non-migratory releas...Vea Mas SILCOLEASE EMULSION CATA 909 a non-ionic aqueous emulsion of polymethylsiloxane grafted with reactive chemicals with the addition of a Platinum salt. It is used as an emulsion catalyst for the range of SILCOLEASE EMULSIONS to obtain a non-migratory release coating for flexible substrates such as papers and films. Vea Menos | |
| SILCOLEASE EMULSION CATA 911 | Elkem Silicones | SILCOLEASE EMULSION CATA 911 is an emulsion of reactive silicone polymers combined with an organometallic catalyst. It is an emulsion catalyst to be used in conjunction with a silicone emulsion intended for release coating of papers and various substrates...Vea Mas SILCOLEASE EMULSION CATA 911 is an emulsion of reactive silicone polymers combined with an organometallic catalyst. It is an emulsion catalyst to be used in conjunction with a silicone emulsion intended for release coating of papers and various substrates, for example SILCOLEASE EMULSION 915. It only catalyses polyaddition type reactions. Vea Menos |
