| Airase® 4500 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Airase® 4500 Defoamer is a proprietary organic oil defoamer designed to control and typically eliminate foam, pinholes and entrapped air in waterbased inks, adhesives and coatings without generating surface defects. It does not contain added mineral oils,...voir plus Airase® 4500 Defoamer is a proprietary organic oil defoamer designed to control and typically eliminate foam, pinholes and entrapped air in waterbased inks, adhesives and coatings without generating surface defects. It does not contain added mineral oils, hazardous air pollutants (HAPs), or alkyl phenol ethoxylates (APEs). voir moins | |
| Airase® 5700 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Airase® 5700 Defoamer is a structured siloxane defoamer line (SSDL) defoamer - a member of aline of products that spans the application space from strong defoaming to high compatibility. Airase® 5700 Defoamer is a formulated product that contains no adde...voir plus Airase® 5700 Defoamer is a structured siloxane defoamer line (SSDL) defoamer - a member of aline of products that spans the application space from strong defoaming to high compatibility. Airase® 5700 Defoamer is a formulated product that contains no added solvent, HAPs, or alkylphenol ethoxylates. This siloxane-based defoamer was developed for use in a wide range of water-based applications. Airase® 5700 Defoamer is formulated for incorporation in the let-down of a coating or ink. Airase® 5700 Defoamer can provide an excellent balance of effective defoaming and film compatibility. voir moins | |
| Carbowet® 138 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Carbowet® 138 Surfactant is a multifunctional additive for pigment and substrate wetting. This nonionic surfactant is typically used alone or in combination with an anionic surfactant. This cost-effective surfactant can provide rapid substrate and pigment...voir plus Carbowet® 138 Surfactant is a multifunctional additive for pigment and substrate wetting. This nonionic surfactant is typically used alone or in combination with an anionic surfactant. This cost-effective surfactant can provide rapid substrate and pigment wetting and perform in a wide range of applications. voir moins | |
| Carbowet® GA-211 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Carbowet® GA-211 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-211 surfactant can provide exceptional dry pigment w...voir plus Carbowet® GA-211 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-211 surfactant can provide exceptional dry pigment wetting and deaeration and optimal milling efficiency, allowing for faster and stronger color development. The combination of properties provided by Carbowet® GA-211 surfactant can be used in a variety of applications for dynamic wetting, compatibilization, emulsification, and stabilization where an easy-to-incorporate liquid additive is desired. Carbowet® GA-211 surfactant offers low foam and strong dynamic wetting properties. voir moins | |
| Carbowet® GA-221 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Carbowet® GA-221 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-221 surfactant can provide exceptional dry pigment w...voir plus Carbowet® GA-221 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-221 surfactant can provide exceptional dry pigment wetting and deaeration and optimizes milling efficiency, allowing for faster and stronger color development. The combination of properties provided by Carbowet® GA-221 surfactant can be used in a variety of applications for dynamic wetting, compatibilization, emulsification, and stabilization where an easy-to-incorporate liquid additive is desired. Compared to related products, Carbowet® GA-221 surfactant offers the most stabilization benefits and is a first choice for organic and carbon black pigment dispersions. voir moins | |
| DYNOL™ 604 Surfactant | Evonik Operations GmbH, BL Interface & Performance | DYNOL™ 604 Surfactant is a low-VOC, low foam, nonionic wetting agent ideal for high-performance waterborne applications. This wetting agent has the ability to reduce both equilibrium and dynamic surface tension to a degree not found with other surfactants...voir plus DYNOL™ 604 Surfactant is a low-VOC, low foam, nonionic wetting agent ideal for high-performance waterborne applications. This wetting agent has the ability to reduce both equilibrium and dynamic surface tension to a degree not found with other surfactants. voir moins | |
| Dynol™ 607 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Dynol™ 607 surfactant has been developed to meet the growing need for high performance and cost effective surfactants. It provides a unique balance of properties for a wide range of waterbased industrial applications compared with traditional surfactants ...voir plus Dynol™ 607 surfactant has been developed to meet the growing need for high performance and cost effective surfactants. It provides a unique balance of properties for a wide range of waterbased industrial applications compared with traditional surfactants such as fluorosurfactants and silicones. Dynol™ 607 applications may include, coatings, graphic arts, adhesives, latex dipping, dye and pigment synthesis, pigment grinding, metalworking fluids, waste water treatment and more. voir moins | |
| Dynol™ 980 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Dynol™ 980 superwetting surfactant is an optimized siloxane-based surfactant providing good equilibrium and dynamic surface tension reduction in a wide range of aqueous formulations. Designed to provide superwetting on difficult-to-wet substrates, it offe...voir plus Dynol™ 980 superwetting surfactant is an optimized siloxane-based surfactant providing good equilibrium and dynamic surface tension reduction in a wide range of aqueous formulations. Designed to provide superwetting on difficult-to-wet substrates, it offers superior substrate wetting with low foam and excellent compatibility. The characteristics of Dynol™ 980 surfactant enable exceptional performance in waterborne wood coatings and overprint varnishes. This product can also provide good flow and leveling under diverse application conditions. voir moins | |
| Isocryl® C-70 | Estron Chemical, Inc. | Isocryl® C-70 is a moderate to high Tg carboxyl functional solid acrylic resin suitable for use as a curative resin in epoxy formulations, such as acrylic hybrid powder coatings, industrial solvent based coatings, or adhesives. Isocryl® C-70 can afford co...voir plus Isocryl® C-70 is a moderate to high Tg carboxyl functional solid acrylic resin suitable for use as a curative resin in epoxy formulations, such as acrylic hybrid powder coatings, industrial solvent based coatings, or adhesives. Isocryl® C-70 can afford coatings or adhesives with excellent chemical resistance, flexibility, outdoor durability, green strength, modulus and impact resistance. Because of its relatively high acid value, Isocryl® C-70 may provide enhanced adhesion to certain substrates and may be a good pigment dispersing resin. voir moins | |
| Lumicryl® 1928 | Estron Chemical, Inc. | Lumicryl® 1928 is a 100% solids resin composition based upon a reactive acrylic macromer diluted in TCDDMDA1. Lumicryl® 1928 is designed to provide excellent adhesion to both low and high surface energy substrates, and may be used as the primary film-form...voir plus Lumicryl® 1928 is a 100% solids resin composition based upon a reactive acrylic macromer diluted in TCDDMDA1. Lumicryl® 1928 is designed to provide excellent adhesion to both low and high surface energy substrates, and may be used as the primary film-forming component or as an adhesion promoting additive in UV/EB formulations for various applications. voir moins | |
| PEL-CAT CA100 | Ele Corporation | PEL-CAT CA100 is an efficient tertiary amine accelerator and curing agent for epoxy resin systems. It is a technical preparation of Tris-(Dimethylaminomethyl) Phenol, a Mannich base. This product functions as a Lewis base containing unshared electrons tha...voir plus PEL-CAT CA100 is an efficient tertiary amine accelerator and curing agent for epoxy resin systems. It is a technical preparation of Tris-(Dimethylaminomethyl) Phenol, a Mannich base. This product functions as a Lewis base containing unshared electrons that facilitate the operning of the oxirane ring of epoxides. This compound shows marked acceleration because of the presence of the phenolic hydroxyl group. It is an activator for curing agents such as polyamides, amidoamines and amine adducts. PEL-CAT CA100 finds use in many applications including adhesives, casting and flooring. The low volatility of this product minimizes odors. voir moins | |
| PEL-EST CF190 | Ele Corporation | PEL-EST CF190 is propoxylated castor oil based non-silicone defoamer. It retains the fluidity of the original oil and is useful in the formation of organic defoamers. PEL-EST CF190 is water-dispersable. It is an excellent choice as a natural and renewab...voir plus PEL-EST CF190 is propoxylated castor oil based non-silicone defoamer. It retains the fluidity of the original oil and is useful in the formation of organic defoamers. PEL-EST CF190 is water-dispersable. It is an excellent choice as a natural and renewable organic defoamer. voir moins | |
| PEL-HIB CC220 | Ele Corporation | PEL-HIB CC220 corrosion inhibitor is an amine borate ester suitable for use with aluminum and steel substrates. Originally introduced as an alternative to nitrites, it affords the same level of protection to ferrous materials. It provides excellent rust i...voir plus PEL-HIB CC220 corrosion inhibitor is an amine borate ester suitable for use with aluminum and steel substrates. Originally introduced as an alternative to nitrites, it affords the same level of protection to ferrous materials. It provides excellent rust inhibition and aids lubrication. PEL-HIB CC220 is very water soluble. In addition to its applications in metalworking fluids and coolants, cooling water and boiler operations, oil well and refinery operations, fuels, lubricants and greases, PEL-HIB CC220 also finds its uses in inorganic coatings, organic coatings, and printing inks. voir moins | |
| PEL-PAG CF240 | Ele Corporation | PEL-PAG CF240 is a water-soluble, non-silicone defoamer. It is butanol alkoxylated. PEL-PAG CF240 is used as a defoamer in waterborne paint and coatings. It can also be used as freeze-thaw stabilizer for latexes emulsions. | |
| PEL-PHOS CD260 | Ele Corporation | PEL-PHOS CD260 is a dispersant, lubricant, anti-wear additive, corrosion inhibitor, wetting agent, emulsifier, and detergent. It is both biodegradable and a non-ecotoxic surfactant. PEL-PHOS CD260 can also be used as co-emulsifier for emulsion polymerizat...voir plus PEL-PHOS CD260 is a dispersant, lubricant, anti-wear additive, corrosion inhibitor, wetting agent, emulsifier, and detergent. It is both biodegradable and a non-ecotoxic surfactant. PEL-PHOS CD260 can also be used as co-emulsifier for emulsion polymerization. voir moins | |
| PEL-PHOS CD270 | Ele Corporation | PEL-PHOS CD270 is an aqueous solution of the sodium salt of a medium HLB, aromatic, phosphate ester. PEL-PHOS CD270 is a useful pigment dispersion agent for the manufacture of paints. It is also a detergent, foamer, co...voir plus PEL-PHOS CD270 is an aqueous solution of the sodium salt of a medium HLB, aromatic, phosphate ester. PEL-PHOS CD270 is a useful pigment dispersion agent for the manufacture of paints. It is also a detergent, foamer, corrosion inhibitor, emulsifier for detergent concentrates & metalworking fluids, FDA, EPA compliance. voir moins | |
| PEL-PHOS CE250 | Ele Corporation | PEL-PHOS CE250 is a phosphate ester of alkoxylated isotridecyl alcohol. It is useful as an emulsifier for emulsion polymerization. It can also be used as co-dispersant and stabilizer for water-based coatings and paints. | |
| PEL-QUAT CS280 | Ele Corporation | PEL-QUAT CS280 is a quaternary salt. It is a very concentrated liquid consisting primarily of isostearyl ethylimidazolinium ethosulfate. PEL-QUAT CS280 is compatible with waterborne coating systems stabilized by anionic surfacants. PEL-QUAT CS280 is a mu...voir plus PEL-QUAT CS280 is a quaternary salt. It is a very concentrated liquid consisting primarily of isostearyl ethylimidazolinium ethosulfate. PEL-QUAT CS280 is compatible with waterborne coating systems stabilized by anionic surfacants. PEL-QUAT CS280 is a multi-functional additive. It can be used as an effective anti-static agent, wetting agent for coatings and adhesives, and as a quat emulsifier for drilling fluid. voir moins | |
| PEL-SIL CD710 | Ele Corporation | PEL-SIL CD710 is a hydrophobic organo-modified silicone-based additive consisting of a siloxane backbone and ethylene oxide (EO) and propylene oxide (PO)polyether side chains. PEL-SIL CD710 minimizes foam stability and is an excellent defoamer for waterbo...voir plus PEL-SIL CD710 is a hydrophobic organo-modified silicone-based additive consisting of a siloxane backbone and ethylene oxide (EO) and propylene oxide (PO)polyether side chains. PEL-SIL CD710 minimizes foam stability and is an excellent defoamer for waterborne and solvent-based coatings and inks, and textile fibre processing applications. PEL-SIL CD710 is also recommended for use as a wetting agent, dispersant, and secondary emulsifier. voir moins | |
| PEL-SIL CL290 | Ele Corporation | PEL-SIL CL290 is an organo-modified silicone-based additive consisting of a siloxane backbone and polyethylene-oxide (EO) and polypropylene oxide (PO) side chains. PEL-SIL CE 390 has recoatability and low tendency to foam. It is good compatibility with ma...voir plus PEL-SIL CL290 is an organo-modified silicone-based additive consisting of a siloxane backbone and polyethylene-oxide (EO) and polypropylene oxide (PO) side chains. PEL-SIL CE 390 has recoatability and low tendency to foam. It is good compatibility with many resin systems. PEL-SIL CL290 is an excellent silicone-based additive for improving slip and mar esistance and reducing friction coefficient for solvent-borne, water-borne, and UV/EB cured coating systems. It can be used for coatings in industrial and auto, wood, and overprint vanishes and inks. voir moins | |
| PEL-SIL CL310 | Ele Corporation | PEL-SIL CL310 is a hydrophobic organo-modified silicone-based additive consisting of a siloxane backbone and polypropylene oxide (PO) side chains. PEL-SIL CL310 minimizes foam stability and is an excellent defoamer for waterborne industrial or decorative ...voir plus PEL-SIL CL310 is a hydrophobic organo-modified silicone-based additive consisting of a siloxane backbone and polypropylene oxide (PO) side chains. PEL-SIL CL310 minimizes foam stability and is an excellent defoamer for waterborne industrial or decorative coatings. PEL-SIL CL310 is compatible with solvent-borne coatings and inks. It provides good low and leveling performance, mar resistance, antiblocking and releasing properties. voir moins | |
| PEL-SIL CL320 | Ele Corporation | PEL-SIL CL320 is a low HLB silicone surfactant and a leveling & gloss agent. It is used as an additive for polyurethane coating resin systems. PEL-SIL CL320 will react into PU coatings to give silicone properties to the surface because it is hydrxyl funct...voir plus PEL-SIL CL320 is a low HLB silicone surfactant and a leveling & gloss agent. It is used as an additive for polyurethane coating resin systems. PEL-SIL CL320 will react into PU coatings to give silicone properties to the surface because it is hydrxyl functional. It is useful for imparting silicone characteristics itno synthetic leather top coat formulations. voir moins | |
| PEL-SIL CL330 | Ele Corporation | PEL-SIL CL330 is a silicone-based additive consisting of a siloxane backbone and polyethylene-oxide (EO) side chains. It is stable in neutral or mildly acid or alkaline aqueous solutions. It is recommended for use as a leveling and wetting agent in water-...voir plus PEL-SIL CL330 is a silicone-based additive consisting of a siloxane backbone and polyethylene-oxide (EO) side chains. It is stable in neutral or mildly acid or alkaline aqueous solutions. It is recommended for use as a leveling and wetting agent in water-borne paints and coatings in automotive, transportation, construction and aerospace industries. It can also be used in solvent-based and high solid/UV curable coatings as leveling agent. For polyurethane foam coatings, PEL-SIL CL330 acts a surfactant and foam cell stabilizer. It is not compatible on the isocyanate side and must be added with the polyol. It exhibits excellent compatibility with most polyol premixes. voir moins | |
| PEL-SIL CL340 | Ele Corporation | PEL-SIL CL340 is a nonreactive, acetate capped, silicone glycol copolymer surfactant supplied at 100 percent active concentration. It provides slip, gloss enhancement, pigment treatment and leveling for ink and coatings applications. Additionally, it prov...voir plus PEL-SIL CL340 is a nonreactive, acetate capped, silicone glycol copolymer surfactant supplied at 100 percent active concentration. It provides slip, gloss enhancement, pigment treatment and leveling for ink and coatings applications. Additionally, it provides mar resistance for coatings applications such as glossy printed materials. voir moins | |
| PEL-SIL CL350 | Ele Corporation | PEL-SIL CL350 is a polysiloxane with EO/PO polyether side chains. It can be used as a low foaming flow and leveling agent and wetting agent in waterborne and solventborne coatings and inks. PEL-SIL CL350 is also reactive in 2K polyurethane systems as a r...voir plus PEL-SIL CL350 is a polysiloxane with EO/PO polyether side chains. It can be used as a low foaming flow and leveling agent and wetting agent in waterborne and solventborne coatings and inks. PEL-SIL CL350 is also reactive in 2K polyurethane systems as a resin and surface modifier. Other uses for PEL-SIL CL350 include surface tension reduction in silicone emulsions and improvement of drainage in pulp brownstock washing. voir moins | |
| PEL-SIL CL360 | Ele Corporation | PEL-SIL CL360 is an organo-modified silicone-based additive consisting of a siloxane backbone and polyethylene-oxide (EO) and polypropylene oxide (PO) side chains. It has pendant molecular structure. PEL-SIL CL360 is an excellent flow and leveling agent f...voir plus PEL-SIL CL360 is an organo-modified silicone-based additive consisting of a siloxane backbone and polyethylene-oxide (EO) and polypropylene oxide (PO) side chains. It has pendant molecular structure. PEL-SIL CL360 is an excellent flow and leveling agent for solvent-based coatings and inks. It can also be used as a defoamer or anti-foaming agent for waterborne coatings systems. In polyurethane foam coatings, PEL-SIL CL360 acts as a surfactant and foam cell stabilizer. It is not compatible on the isocyanate side and must be added with the polyol. voir moins | |
| PEL-SIL CL370 | Ele Corporation | PEL-SIL CL370 is an amino-functional siloxane with pedant propyldiamine groups. The specialty amino polysiloxane can be used in coatings and adhesives for improving adhesion to various substrates. PEL-SIL CL370 is a reactive amine-containing siloxane addi...voir plus PEL-SIL CL370 is an amino-functional siloxane with pedant propyldiamine groups. The specialty amino polysiloxane can be used in coatings and adhesives for improving adhesion to various substrates. PEL-SIL CL370 is a reactive amine-containing siloxane additive as resin modifier for epoxy resin and polyurethane systems to impart flexibility and strength. voir moins | |
| PEL-SIL CL380 | Ele Corporation | PEL-SIL CL380 is a linear, 100% active, PEG-10 siloxane polyether. It is an excellent flow and leveling agent for both waterborne and solventborne coatings. It also provides slip and mar resistance as well as anti-blocking properties. For UV/EB cure coati...voir plus PEL-SIL CL380 is a linear, 100% active, PEG-10 siloxane polyether. It is an excellent flow and leveling agent for both waterborne and solventborne coatings. It also provides slip and mar resistance as well as anti-blocking properties. For UV/EB cure coatings, PEL-SIL CL380 can reduce coefficient of friction reduction without generating foams or lowering gloss. It may also be incorporated into polymer systems by virtue of its two primary hydroxyl in polyurethane systems. voir moins | |
| PEL-SIL CL390 | Ele Corporation | PEL-SIL CL390 is a specialty quaternary organosilicone. The dialkyl quats polysiloxane is substantive to fibers. It provides anti-stat, lubricity and softness in textile coating applications. It is non-yellowing and water repellent. PEL-SIL can be used ...voir plus PEL-SIL CL390 is a specialty quaternary organosilicone. The dialkyl quats polysiloxane is substantive to fibers. It provides anti-stat, lubricity and softness in textile coating applications. It is non-yellowing and water repellent. PEL-SIL can be used as additive to impart antimicrobial activity for polysiloxane coatings in medical device and marine coatings. voir moins | |
| PEL-SIL CL400 | Ele Corporation | PEL-SIL CL400 is a linear, 100% active, PEG-10 siloxane polyether. It is a slip control agent for both waterborne, solventborne UV/EB coatings and inks. It is also a flow and leveling agent and defoamer that can be incorporated into polymer systems throug...voir plus PEL-SIL CL400 is a linear, 100% active, PEG-10 siloxane polyether. It is a slip control agent for both waterborne, solventborne UV/EB coatings and inks. It is also a flow and leveling agent and defoamer that can be incorporated into polymer systems through its two primary hydroxyls in polyurethane systems. voir moins | |
| PEL-SIL CW300 | Ele Corporation | PEL-SIL CW300 is a low molecular weight, nonionic silicone-based wetting additive that can reduce the surface tension of aqueous solutions significantly lower than conventional nonionic surfactants can. It is stable at neutral pH and compatible with other...voir plus PEL-SIL CW300 is a low molecular weight, nonionic silicone-based wetting additive that can reduce the surface tension of aqueous solutions significantly lower than conventional nonionic surfactants can. It is stable at neutral pH and compatible with other anionic sirfactants and nonionic surfactants. voir moins | |
| PEL-SIL™ CX740 | Ele Corporation | PEL-SIL™ CX740 is an epoxy functionalized siloxane polyether. With its silicone and organic combination and dual reactive hydroxy and epoxy functionality, PEL-SIL™ CX740 offers unique capability to modify epoxy and polyurethane systems. It can impart surf...voir plus PEL-SIL™ CX740 is an epoxy functionalized siloxane polyether. With its silicone and organic combination and dual reactive hydroxy and epoxy functionality, PEL-SIL™ CX740 offers unique capability to modify epoxy and polyurethane systems. It can impart surface and bulk properties, such as gloss, slip, hydrophobicity, and mechanical. Due to its low viscosity, PEL-SIL™ CX740 enhances the process for better mixing and flow for compounds and composites. voir moins | |
| PEL-STAT CS410 | Ele Corporation | PEL-STAT CS410 is a very effective internal antistatic agent. It is ideal for use in anti-static coatings for floors, walls, and anywhere anti-static properties are required. | |
| Polymer ST 48 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 48 offers a good handling viscosity and is therefore easy to apply manually. Formulation surfaces are quickly tack-free after application, which ensures rapid processing and avoids long waiting times. It is especially recommended for the applic...voir plus Polymer ST 48 offers a good handling viscosity and is therefore easy to apply manually. Formulation surfaces are quickly tack-free after application, which ensures rapid processing and avoids long waiting times. It is especially recommended for the application as sealant for interior or exterior joints, e.g. expansion or connection joints, interior joints for dry walling, joints at staircases. voir moins | |
| Polymer ST 61 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 61 is a high quality polymer which is used for wood floor adhesive formulations. Polymer ST 61 allows a high degree of flexibility for the formulations: adhesives with high strength and hardness are possible as well as soft adhesives with high ...voir plus Polymer ST 61 is a high quality polymer which is used for wood floor adhesive formulations. Polymer ST 61 allows a high degree of flexibility for the formulations: adhesives with high strength and hardness are possible as well as soft adhesives with high elasticity. voir moins | |
| Polymer ST 61 LV | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 61 LV is a plasticizer-free product which addresses the same formulation properties as Polymer ST 61. Its viscosity is approx. 70 % less, thus it allows quicker dosing, lower formulation viscosities and higher possible filler loading levels. | |
| Polymer ST 77 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 77 is free of phthalates and is highly recommended for demanding applications where a balanced stress-strain behavior is required as in transport and assembly applications. Examples for the use of Polymer ST 77-based formulations are the assemb...voir plus Polymer ST 77 is free of phthalates and is highly recommended for demanding applications where a balanced stress-strain behavior is required as in transport and assembly applications. Examples for the use of Polymer ST 77-based formulations are the assembly of superstructural parts, bumpers, etc. Mechanical fastening is often avoided as it could cause damage to the materials used. In addition, it could negatively affect the design. voir moins | |
| Polymer ST 80 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 80 is a high quality binder for adhesive formulations where high bonding strength and high surface hardness after curing are required. | |
| Polymer ST 81 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 81 does not contain plasticizers, it offers a large variability in formulation design. It allows the formulation of both tin- and phthalate-free products. It allows formulators to enter markets such as wood construction, transport and automotiv...voir plus Polymer ST 81 does not contain plasticizers, it offers a large variability in formulation design. It allows the formulation of both tin- and phthalate-free products. It allows formulators to enter markets such as wood construction, transport and automotive, assembly as well as light-weight construction. voir moins | |
| Polytex™ E-100 | Estron Chemical, Inc. | Polytex™ E-100 is a sulfonamide-based resin modifier for use in lacquers, inks, adhesives and UV curable coatings. Polytex™ E-100 enhances gloss, DOI (Distinctness of Image), adhesion to numerous substrates, compatibility and overall coating durability. P...voir plus Polytex™ E-100 is a sulfonamide-based resin modifier for use in lacquers, inks, adhesives and UV curable coatings. Polytex™ E-100 enhances gloss, DOI (Distinctness of Image), adhesion to numerous substrates, compatibility and overall coating durability. Polytex™ E-100 has excellent compatibility with most commercial polymeric binders, pigments and plasticizers. voir moins | |
| Polytex™ E-75 | Estron Chemical, Inc. | Polytex™ E-75 is a sulfonamide-based resin modifier for use in lacquers, inks, and adhesives. Polytex™ E- 75 enhances gloss, DOI (Distinctness of Image), adhesion to numerous substrates, compatibility and overall coating durability. Polytex™ E-75 is a for...voir plus Polytex™ E-75 is a sulfonamide-based resin modifier for use in lacquers, inks, and adhesives. Polytex™ E- 75 enhances gloss, DOI (Distinctness of Image), adhesion to numerous substrates, compatibility and overall coating durability. Polytex™ E-75 is a formaldehyde-free resin alternative for nail lacquers. Polytex™ E-75 has compatibility with most commercial polymeric binders, pigments and plasticizers. voir moins | |
| Resiflow® L-37 | Estron Chemical, Inc. | Resiflow® L-37 is a silicone-free, 100% solids, reactive polyacrylate additive for high solids, solvent-based, free radical UV, cationic, coil, and general industrial coatings, inks and adhesives. Resiflow® L-37 has been tested in various formulations and...voir plus Resiflow® L-37 is a silicone-free, 100% solids, reactive polyacrylate additive for high solids, solvent-based, free radical UV, cationic, coil, and general industrial coatings, inks and adhesives. Resiflow® L-37 has been tested in various formulations and is especially effective in urethane acrylates, epoxy acrylates, polyesters, and epoxies. Recommended level of usage is 0.1%-0.5% based on solids. Resiflow® L-37 can be cut in various reactive diluents, aromatic and aliphatic hydrocarbons, esters, ketones, or alcohols for easy incorporation into the formula. voir moins | |
| Sulfonex™ M-80 | Estron Chemical, Inc. | Sulfonex™ M-80 is a tosylamide/formaldehyde resin used as a modifier in lacquers, inks and adhesives to promote gloss, adhesion and overall durability. Sulfonex™ M-80 has compatibility with most commercial polymeric binders, pigments, dyes and plasticize...voir plus Sulfonex™ M-80 is a tosylamide/formaldehyde resin used as a modifier in lacquers, inks and adhesives to promote gloss, adhesion and overall durability. Sulfonex™ M-80 has compatibility with most commercial polymeric binders, pigments, dyes and plasticizers. Solutions of Sulfonex™ M-80 have a low viscosity and offer the advantage of formulating high solids lacquers. Sulfonex™ M-80 improves the compatibility of resins with plasticizers and pigments which may otherwise remain incompatible. In adhesives formulations, Sulfonex™ M-80 helps in bonding many substrates such as cellophane and aluminum foils to themselves or to paper. voir moins | |
| SURFYNOL® 104 | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® 104 surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104 surfactant is a nonionic molecule containing ...voir plus SURFYNOL® 104 surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104 surfactant is a nonionic molecule containing a hydrophilic portion in the middle of two symmetrical hydrophobic groups. Its unique chemical structure allows this product to provide multifunctional properties such as surface tension reduction, foam control and viscosity stabilization. voir moins | |
| SURFYNOL® 104A | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® 104A surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104A surfactant is a nonionic molecule containing...voir plus SURFYNOL® 104A surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104A surfactant is a nonionic molecule containing a hydrophilic portion in the middle of two symmetrical hydrophobic groups. Its unique chemical structure allows this product to provide multifunctional properties such as surface tension reduction, foam control and viscosity stabilization. voir moins | |
| SURFYNOL® 104BC | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in 2-Butoxyethanol. | |
| SURFYNOL® 104DPM | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Dipropylene Glycol Monomethyl Ether. | |
| SURFYNOL® 104E | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Ethylene Glycol. | |
| SURFYNOL® 104H SURFACTANT | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 75% active liquid in Ethylene Glycol. | |
| SURFYNOL® 104PA | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Isopropyl Alcohol. | |
| SURFYNOL® 104PG-50 | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Propylene Glycol. | |
| SURFYNOL® 104S | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 46% active powder on Amorphous Silica. | |
| Surfynol® 107 L | Evonik Operations GmbH, BL Interface & Performance | Surfynol® 107 L is a low-viscosity surfactant that provides substratre wetting and defoaming properties. It also acts as coalescing aid. | |
| SURFYNOL® 2502 | Evonik Operations GmbH, BL Interface & Performance | An ethoxylated/propoxylated acetylenic-based surfactant that provides specific performance benefits in a broad range of water-based systems. 100% active liquid. | |
| SURFYNOL® 420 | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that functions both as a wetting agent and foam control agent. 100% active liquid with an HLB of 4. | |
| SURFYNOL® 440 | Evonik Operations GmbH, BL Interface & Performance | A nonfoaming, nonionic surfactant that is employed for substrate wetting. 100% active liquid with an HLB of 8. | |
| SURFYNOL® 465 | Evonik Operations GmbH, BL Interface & Performance | A nonionic, low-foaming surfactant that is utilized for its wetting and slight emulsification properties. It has a high cloud point for utilization in high-temperature systems. 100% active liquid with an HLB of 13. | |
| SURFYNOL® 485W | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that functions as a wetting agent and has slight emulsification properties. 75% active liquid with an HLB of 17. | |
| SURFYNOL® 82 | Evonik Operations GmbH, BL Interface & Performance | This is a 95% Dimethyl Octynediol surfactant. | |
| SURFYNOL® CT-131 | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® CT-131 is a solvent-free, low-foaming pigment grind aid designed for use in aqueous systems. | |
| SURFYNOL® CT-171 | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® CT-171 is a solvent-free anionic/nonionic grind aid designed to provide both effective pigment wetting and dispersing characteristics for many types of organic pigments. | |
| Surfynol® DF-110 D | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF 110 D is a very compatible molecular defoamer basedon Gemini surfactant technology. Free of silicone and silica. Offers additional dynamic wetting properties. | |
| Surfynol® DF-110BC Defoamer | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF-110BC defoamer is a highly effective, nonionic, molecular defoamer and deaerator. This defoaming/deairentraining agent can be used for a wide variety of applications where foam prevention or foam elimination is necessary without causing surfa...voir plus Surfynol® DF-110BC defoamer is a highly effective, nonionic, molecular defoamer and deaerator. This defoaming/deairentraining agent can be used for a wide variety of applications where foam prevention or foam elimination is necessary without causing surface defects. voir moins | |
| SURFYNOL® DF-110L | Evonik Operations GmbH, BL Interface & Performance | Surfynol DF-110C, Surfynol DF-110D, and Surfynol DF-110L molecular defoamers are highly effective, non-ionic organic products. They do not contain silicone, silica or fluoro products. These three defoaming/de-air entraining agents are useful for a wide ...voir plus Surfynol DF-110C, Surfynol DF-110D, and Surfynol DF-110L molecular defoamers are highly effective, non-ionic organic products. They do not contain silicone, silica or fluoro products. These three defoaming/de-air entraining agents are useful for a wide variety of applications where foam prevention or foam elimination is nescessary without causing surface defects. voir moins | |
| Surfynol® DF-178 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF-178 Defoamer is a formulated defoamer and de-aerator that provides strong defoaming and microfoam control and is particularly effective in spray applications. It is a liquid, 100% active, silicone-based product developed specifically for appl...voir plus Surfynol® DF-178 Defoamer is a formulated defoamer and de-aerator that provides strong defoaming and microfoam control and is particularly effective in spray applications. It is a liquid, 100% active, silicone-based product developed specifically for applications in water-borne coatings and graphic arts that demand both powerful defoaming and defect-free surfaces. voir moins | |
| Surfynol® DF-220 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF-220 Defoamer is a 100% active, silicone-free, silica-free, and alkylphenol ethoxylate (APE)-free organic defoamer that can provide not only high initial efficacy, but also long term sustained defoaming. It is a clear, low viscosity liquid tha...voir plus Surfynol® DF-220 Defoamer is a 100% active, silicone-free, silica-free, and alkylphenol ethoxylate (APE)-free organic defoamer that can provide not only high initial efficacy, but also long term sustained defoaming. It is a clear, low viscosity liquid that has been specifically designed to be used in a variety of water-based formulations, including printing inks, coatings and adhesives. voir moins | |
| SURFYNOL® DF-37 | Evonik Operations GmbH, BL Interface & Performance | A nonionic, acetylenic-based defoamer which promotes foam control as well as surface wetting. 100% active liquid. | |
| SURFYNOL® DF-37 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A nonionic, acetylenic-based defoamer which promotes foam control as well as surface wetting. A unique additive designed to minimize web formation during latex glove and waterborne coating dipping processes. | |
| SURFYNOL® DF-58 | Evonik Operations GmbH, BL Interface & Performance | A silicone-based foam control agent useful in aqueous systems. The product has strong foam control and deairation performance. 100% active liquid. | |
| SURFYNOL® DF-58 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A silicone-based foam control agent useful in aqueous systems. It has strong foam control and deairation performance. Developed for use in water-based coating and ink formulations where strong, rapid defoaming is required. 100% active liquid. | |
| SURFYNOL® DF-62 | Evonik Operations GmbH, BL Interface & Performance | An ether-modified polysiloxane-based defoamer designed to provide excellent knockdown defoaming and sustained antifoaming over time. 100% active liquid. | |
| SURFYNOL® DF-62 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | Ether-modified, silicone defoamer designed to provide excellent knockdown defoaming and sustained antifoaming over time in a variety of waterborne formulations. Useful when long-term defoamer efficacy is needed. 100% active liquid. | |
| SURFYNOL® DF-66 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A liquid, acetylenic-modified polysiloxane-based emulsion defoamer which provides excellent balance of initial knockdown and sustained defoaming with no detrimental effects. Designed for use in aqueous ink and coating systems. 46% active liquid. | |
| SURFYNOL® DF-695 | Evonik Operations GmbH, BL Interface & Performance | A silicone emulsion defoamer, which provides initial and sustained defoaming performance in water-based formulations. 100% active liquid. | |
| SURFYNOL® DF-695 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A silicone-based emulsion defoamer designed for use in aqueous ink systems. It is recommended for use in grinding and dispersion as well as letdown applications. 100% active liquid. | |
| SURFYNOL® MD-600S | Evonik Operations GmbH, BL Interface & Performance | This is a highly effective powder product designed to eliminate air entrapment in cementitious-based products for the construction industry. It allows for fast-acting defoaming with long-lasting deaeration, at a molecular level. It also ensures the fast...voir plus This is a highly effective powder product designed to eliminate air entrapment in cementitious-based products for the construction industry. It allows for fast-acting defoaming with long-lasting deaeration, at a molecular level. It also ensures the fast escape of air entrapped while incorporating water and during mixing. voir moins | |
| Surfynol® MD20 | Evonik Operations GmbH, BL Interface & Performance | Surfynol® MD20 is a 100% active, nonsilicone, liquid product based on Gemini Surfactant Technology. This multifunctional defoamer provides a combination of foam control and dynamic wetting, with the potential to reduce overall additive levels, while minim...voir plus Surfynol® MD20 is a 100% active, nonsilicone, liquid product based on Gemini Surfactant Technology. This multifunctional defoamer provides a combination of foam control and dynamic wetting, with the potential to reduce overall additive levels, while minimizing surface defects. Additional advantages of Surfynol® MD20 include, long-lasting defoamer efficacy, ease of incorporation and good compatibility without separation, synergestic with typical wetting agents, eliminates microfoam, wide compounding latitude, solvent-free and temperature and pH stable (pH 1-13). voir moins | |
| SURFYNOL® PSA-336 | Evonik Operations GmbH, BL Interface & Performance | A powerful solvent-free wetting agent with moderate foaming tendencies. | |
| SURFYNOL® SE | Evonik Operations GmbH, BL Interface & Performance | A nonionic defoaming surfactant which can act as a highly effective wetting agent, defoamer and viscosity stabilizer and often performs more than one of these functions in combination. 80% active liquid with an HLB of 4-5. | |
| SURFYNOL® SE-F | Evonik Operations GmbH, BL Interface & Performance | A nonionic self-emulsifiable surfactant that will reduce surface tension and control foam. 80% active liquid with an HLB of 4-5. | |
| TEGOPAC® Bond 150 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 150 is recommended for usage as a binder in assembly adhesives and sealant formulations. The combination of outstanding through-cure and excellent elastic recovery properties allows formulations with TEGOPAC® Bond 150 to be used in a number ...voir plus TEGOPAC® Bond 150 is recommended for usage as a binder in assembly adhesives and sealant formulations. The combination of outstanding through-cure and excellent elastic recovery properties allows formulations with TEGOPAC® Bond 150 to be used in a number of demanding applications, e.g. in construction of sandwich elements, for flexible bonding in transport applications or for high quality expansion joints. voir moins | |
| TEGOPAC® Bond 160 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 160 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 160 shows excellent through cure properties,...voir plus TEGOPAC® Bond 160 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 160 shows excellent through cure properties, improved water & thermal resistance and excellent elastic recovery properties. The low polymer viscosity allows quick & easy handling. voir moins | |
| TEGOPAC® Bond 170 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 170 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 170 shows excellent through cure properties,...voir plus TEGOPAC® Bond 170 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 170 shows excellent through cure properties, improved water & thermal resistance and excellent elastic recovery properties. The low polymer viscosity allows quick & easy handling. voir moins | |
| TEGOPAC® Bond 251 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 251 is a hybrid polymer with a modified backbone that contains hydrophilic segments. Formulations with TEGOPAC® Bond 251 are suitable to replace flexible PUR adhesives and sealants. | |
| TEGOPAC® RD 1 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® RD 1 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers,...voir plus TEGOPAC® RD 1 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers, and other additives is possible to address applications like parquet adhesives, roof sealing applications or pressure sensitive adhesives. voir moins | |
| TEGOPAC® RD 2 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® RD 2 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers,...voir plus TEGOPAC® RD 2 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers, and other additives is possible to address applications like parquet adhesives, roof sealing applications or pressure sensitive adhesives. voir moins | |
| TEGOPAC® Seal 100 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Seal 100 is a moisture curing silane-modified polymer recommended for low modulus sealant formulations which are used in construction applications (e.g. for façades, expansion joints, etc. ) or for indoor applications. TEGOPAC® Seal 100 is also ...voir plus TEGOPAC® Seal 100 is a moisture curing silane-modified polymer recommended for low modulus sealant formulations which are used in construction applications (e.g. for façades, expansion joints, etc. ) or for indoor applications. TEGOPAC® Seal 100 is also recommended for use in sealant and adhesive formulations where vibration and sound dampening is an issue. voir moins | |
| ZetaSperse® 170 Dispersant | Evonik Operations GmbH, BL Interface & Performance | ZetaSperse® 170 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles with acidic surface groups. A nonionic stabilizing surfactant, ZetaSperse® 170 dispersant utilizes a tertiary amine anchoring grou...voir plus ZetaSperse® 170 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles with acidic surface groups. A nonionic stabilizing surfactant, ZetaSperse® 170 dispersant utilizes a tertiary amine anchoring group that has been found to have particularly strong affinity for carbon black pigments, titanium dioxide pigments, and other pigments and particles with acidic surface groups. ZetaSperse® 170 dispersant is most effective when used as a secondary dispersant in conjunction with anionic polymeric dispersants and grind resins where it can provide significant wetting, milling, and steric stabilization benefits, often improving milling efficiency, color development, and dispersion stability, allowing formulators to achieve higher performance. voir moins | |
| ZetaSperse® 179 Dispersant | Evonik Operations GmbH, BL Interface & Performance | ZetaSperse® 179 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles. A nonionic, high-HLB surfactant, ZetaSperse® 179 Dispersant provides performance benefits in the aqueous dispersion of organic, c...voir plus ZetaSperse® 179 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles. A nonionic, high-HLB surfactant, ZetaSperse® 179 Dispersant provides performance benefits in the aqueous dispersion of organic, carbon black, and inorganic pigments as well as fillers and functional solid chemicals. Ideal applications include resinated dispersions, colorants and pigment dispersions, inks and graphic arts, architectural and industrial coatings, and industrial processes. voir moins |
