EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down v...voir plus
EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down viruses and bacteria. It eradicates viruses such as influenza, SARS-COV-2, dengue & hepatitis and bacteria such as E. coli, MSRA, streptococcus, listeria, pneumonia, and salmonella. It is activated by light and displays quick drying at room temperature. Spray application is recommended to reach thin monolayers. It exhibits curing at room temperature up to 300°C and super hard particles (1GPa Vickers). It is easy to apply & durable, allowing longer disinfection intervals while preserving hygiene level. It shows non-silver leaching, efficacious even under low light conditions, lower service frequency, and no need for frequent disinfection routine. It is used in the state-of-the-art continuous antimicrobial coating for high-traffic areas. EXOCOAT® AM is suitable for topcoats for any surface inside buildings, stores, hospitals, and vehicles. The shelf life of this product is 9 months. voir moins
Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl com...voir plus
Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl compounds, and PVC based plastisols. It can also be used in PVC based polymers, nitrocellulose resins, and cyanoacrylate adhesives. voir moins
Ketjenflex® 6 is a toluene sulfonamide in the form of a white crystalline powder. It is used as a plasticizer in inks, adhesives, and coatings. Ketjenflex® 6 can be used with resins such as nitrocellulose, polyamide, PVAC, rosin, epoxy, and more.
Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coa...voir plus
Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coatings, synthetic polyamides, epoxy coatings and adhesives, and more. voir moins
Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wo...voir plus
Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wood adhesives, epoxy and polyurethane coatings and adhesives, and other applications. voir moins
Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings.
Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printi...voir plus
Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printing inks. voir moins
Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured in...voir plus
Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured into desired formulations. It has applications in nitrocellulose coatings, cellulose acetate formulations, and printing inks. voir moins
MAXGARD® 1000 is a light yellow powder UV light stabilizer used for protecting polyurethane coatings, oil paints and acrylic adhesives. This product has a melting point of 195-197°C and a mass density of 1.21 g/cm3 at 25°C. It exhibits a broad absorption ...voir plus
MAXGARD® 1000 is a light yellow powder UV light stabilizer used for protecting polyurethane coatings, oil paints and acrylic adhesives. This product has a melting point of 195-197°C and a mass density of 1.21 g/cm3 at 25°C. It exhibits a broad absorption band which extends into the UV-A range. voir moins
MAXGARD® 1030 is a light yellow powder that is a special blend of benzophenone-2 and benzophenone-6, making it an effective light stabilizer for protecting coatings against UV radiation. This product has a mass density of 1.26 g/cm3 at 25°C and an absorpt...voir plus
MAXGARD® 1030 is a light yellow powder that is a special blend of benzophenone-2 and benzophenone-6, making it an effective light stabilizer for protecting coatings against UV radiation. This product has a mass density of 1.26 g/cm3 at 25°C and an absorptivity of 52 at 339nm. It is suitable for use in polyurethane coatings, furniture stains and varnishes, nitrocellulose lacquers, fluorescent pigments and acrylic adhesives. voir moins
MAXGARD® 2700 is a light yellow powder that can be used as an UV stabilizer for protecting coatings from the damaging UV radiation which is a component of natural sunlight. This product has a melting point of 175°C and a mass density of 1.19 g/cm3 at 25°C...voir plus
MAXGARD® 2700 is a light yellow powder that can be used as an UV stabilizer for protecting coatings from the damaging UV radiation which is a component of natural sunlight. This product has a melting point of 175°C and a mass density of 1.19 g/cm3 at 25°C. It is suitable for use in polyurethane coatings, epoxy coatings, vinyl and acrylic adhesives. voir moins
MAXGARD® 300 is a light yellow powder that is a light stabilizer used for broad-spectrum protection of acrylic adhesives, polyurethane coatings, furniture stains and varnishes, nitrocellulose lacquers, pigments and emulsions from damage caused by UV radia...voir plus
MAXGARD® 300 is a light yellow powder that is a light stabilizer used for broad-spectrum protection of acrylic adhesives, polyurethane coatings, furniture stains and varnishes, nitrocellulose lacquers, pigments and emulsions from damage caused by UV radiation. This product has a melting point of 130-132°C and a mass density of 1.34 g/cm3 at 25°C. voir moins
MAXGARD® 400 is an off white powder that is used as an UV stabilizer to protect nitrocellulose lacquers, varnishes, and pressure sensitive acrylic adhesives from UV damage. This product has a melting range of 140-143°C and a mass density of 1.27 g/cm3 at ...voir plus
MAXGARD® 400 is an off white powder that is used as an UV stabilizer to protect nitrocellulose lacquers, varnishes, and pressure sensitive acrylic adhesives from UV damage. This product has a melting range of 140-143°C and a mass density of 1.27 g/cm3 at 25°C. voir moins
MAXGARD® 500 is a free flowing light yellow powder that is used as an UV absorber and stabilizer to protect oil-based paints, nitrocellulose lacquers, and varnishes. This product has a melting range of 63-65°C and a mass density of 1.33 g/cm3 at 25°C.
MAXGARD® 600 is a 100% active, pale yellow liquid that is used as an UV stabilizer in industrial coatings, such as polyurethanes, as well as vinyl and acrylic adhesives. This product has a melting range of ~5°C and a mass density of 1.27 g/cm3 at 25°C.
MAXGARD® 700 is a free flowing, light yellow powder that is used primarily in polyurethanes, acrylic coatings, alkyd varnishes and vinyl and acrylic adhesives. It can be used as an UV stabilizer to protect the end product from degradation due to natural s...voir plus
MAXGARD® 700 is a free flowing, light yellow powder that is used primarily in polyurethanes, acrylic coatings, alkyd varnishes and vinyl and acrylic adhesives. It can be used as an UV stabilizer to protect the end product from degradation due to natural sunlight. This product has a melting range of 47-49°C and a mass density of 1.16 g/cm3 at 25°C. voir moins
MAXGARD® 900 is a free flowing light yellow powder which can be used as an UV stabilizer. It is very effective for UV protection of oil-based paints, urethane coatings, pressure sensitive acrylic and vinyl adhesives. This product has a melting range of 68...voir plus
MAXGARD® 900 is a free flowing light yellow powder which can be used as an UV stabilizer. It is very effective for UV protection of oil-based paints, urethane coatings, pressure sensitive acrylic and vinyl adhesives. This product has a melting range of 68-74°C and a mass density of 1.37 g/cm3 at 25°C. voir moins
MAXGARD® DPA-2 is a white powder designed to provide good heat stability and UV protection with little to no color contribution to the substrate. It can be used as an UV stabilizer in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacq...voir plus
MAXGARD® DPA-2 is a white powder designed to provide good heat stability and UV protection with little to no color contribution to the substrate. It can be used as an UV stabilizer in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacquers, and acrylic and vinyl adhesives. This product has a melting point of 93°C and a mass density of 1.16 g/cm3 at 25°C. voir moins
MAXGARD® DPA-8 is a 100% active, clear light amber, viscous liquid stabilizer that has low color and low volatility. It is often used in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacquers, and acrylic and vinyl adhesives. This pro...voir plus
MAXGARD® DPA-8 is a 100% active, clear light amber, viscous liquid stabilizer that has low color and low volatility. It is often used in acrylic coatings, varnishes, polyurethane coatings, nitrocellulose lacquers, and acrylic and vinyl adhesives. This product has a solidification point of 10°C and a mass density of 1.05 g/cm3 at 25°C. voir moins
Upgrade to a premium Prospector account to filter by ingredient properties and view compliance highlights. These features can help you make smarter formulation decisions with instant access to:
Search by physical and chemical properties. Personal Care & Cosmetics only.
Désolé mais l'industrie que vous avez sélectionnée n'est pas disponible actuellement dans votre langue. Vous pouvez choisir une des langues ci-dessous pour sélectionner l'industrie ou sinon fermer cette fenêtre.
