| 1-Vinylimidazole, VIM | BASF SE, Intermediates Division | 1-Vinylimidazole, VIM is reactive diluent for UV coatings (inks, adhesives, general coatings). A monomer for water soluble specialty polymers (oilfield and cosmetics). It has high reactivity for radical polymerization and improves wetting and adhesion on...voir plus 1-Vinylimidazole, VIM is reactive diluent for UV coatings (inks, adhesives, general coatings). A monomer for water soluble specialty polymers (oilfield and cosmetics). It has high reactivity for radical polymerization and improves wetting and adhesion on plastic. voir moins | |
| 1,2-Dimethylimidazole, Lupragen DMI | BASF SE, Intermediates Division | 1,2-Dimethylimidazole, Lupragen DMI is a selective catalyst for epoxy and urethanes reactions. 1,2-Dimethylimidazole is used for two components epoxy systems and for modification of epoxy resins and for preparation of polyurethanes. | |
| 1,3-Diaminopropane | BASF SE, Intermediates Division | 1,3-Diaminopropane is a cross linker for epoxy resins, building block for polyamides. 1,3-Diaminopropane is frequently used in epoxy coatings, epoxy composites and epoxy adhesives. | |
| 1,3-Dioxolane | BASF SE, Intermediates Division | 1,3-Dioxolane is a powerful aprotic solvent for use in formulations, in production processes, or even as a reactant. Dioxolane can be used in pressure sensitive adhesives and sealants, as well as for dissolving polar polymers, including polyesters, epoxi...voir plus 1,3-Dioxolane is a powerful aprotic solvent for use in formulations, in production processes, or even as a reactant. Dioxolane can be used in pressure sensitive adhesives and sealants, as well as for dissolving polar polymers, including polyesters, epoxies, urethanes, and polyacrylamide. It can also be used as a solvent in polyester film seaming. voir moins | |
| 1,4-Butanediol, BDO | BASF SE, Intermediates Division | 1,4-Butanediol, BDO is a building block for unsaturated polyesters, saturated polyesters and polyurethanes. It's suitable for flexible furniture coatings and repair putties and is used for flexible solvent borne paints, plasticizers and soft segments for...voir plus 1,4-Butanediol, BDO is a building block for unsaturated polyesters, saturated polyesters and polyurethanes. It's suitable for flexible furniture coatings and repair putties and is used for flexible solvent borne paints, plasticizers and soft segments for polyurethanes. voir moins | |
| 1,4-Cyclohexane dimethanol divinyl ether, CHDM di | BASF SE, Intermediates Division | 1,4-Cyclohexane dimethanol divinyl ether, CHDM di is a reactive diluent for unsaturated polyesters, UV coatings, UV inks, UV adhesives, release coatings and artificial marble. | |
| 1,4-Cyclohexane dimethanol mono vinyl ether, CHDM Mono | BASF SE, Intermediates Division | 1,4-Cyclohexane dimethanol mono vinyl ether, CHDM Mono is a building block for macro monomers and monomer for vinyl copolymers. It is a reactive diluent in UV-coatings and in adhesives. It is used for water and solvent based hydroxyl-functional vinyl po...voir plus 1,4-Cyclohexane dimethanol mono vinyl ether, CHDM Mono is a building block for macro monomers and monomer for vinyl copolymers. It is a reactive diluent in UV-coatings and in adhesives. It is used for water and solvent based hydroxyl-functional vinyl polymers, which are cross-linked with polyisocyanates and melamine resins. voir moins | |
| 1,5-Pentanediol, PDO | BASF SE, Intermediates Division | 1,5-Pentanediol, PDO is a building block for saturated polyesters, unsaturated polyesters and polyurethanes, solvent for inkjet ink formulations. It's suitable for polyesters for solvent-borne paints (stoving enamels, two-components paints, can & coil co...voir plus 1,5-Pentanediol, PDO is a building block for saturated polyesters, unsaturated polyesters and polyurethanes, solvent for inkjet ink formulations. It's suitable for polyesters for solvent-borne paints (stoving enamels, two-components paints, can & coil coatings), polyester plasticizers and for soft segments for polyurethanes. voir moins | |
| 1,6-Hexanediol HDO® | BASF SE, Intermediates Division | 1,6-Hexanediol HDO® is a building block for saturated polyesters and polyurethanes acrylic esters of 1,6-Hexanediol are used as reactive diluent for UV-coatings. 1,6-Hexanediol is used in polyesters for solvent-borne paints, in stoving enamels for automo...voir plus 1,6-Hexanediol HDO® is a building block for saturated polyesters and polyurethanes acrylic esters of 1,6-Hexanediol are used as reactive diluent for UV-coatings. 1,6-Hexanediol is used in polyesters for solvent-borne paints, in stoving enamels for automotive coatings, for can-& coil-coating and for general applications. It is preferentially used in two-component paints for plastic coatings and repair coatings. It is suitable for polyester plasticizers and in soft segments for polyurethanes. 1,6-Hexanediol shows an optimum balance of flexibility and toughness (excellent flexibility in combination with sufficient hardness) in polyesters and polyurethane. voir moins | |
| 1,8-Diazabicyclo-5,4,0-undecene-7 Lupragen® N 700 | BASF SE, Intermediates Division | 1,8-Diazabicyclo-5,4,0-undecene-7 Lupragen® N 700 is a catalyst for urethane reactions. 1,8-Diazabicyclo-5,4,0-undecene-7 is suitable for production of polyurethanes and as catalyst for two-components paints for automotive OEM, repair paints, plastic pai...voir plus 1,8-Diazabicyclo-5,4,0-undecene-7 Lupragen® N 700 is a catalyst for urethane reactions. 1,8-Diazabicyclo-5,4,0-undecene-7 is suitable for production of polyurethanes and as catalyst for two-components paints for automotive OEM, repair paints, plastic paints and paints for general application. 1,8-Diazabicyclo-5,4,0-undecene-7 is highly effective. As a liquid, it is easy to handle and shows high compatibility with resins. voir moins | |
| 2-(2-Aminoethoxy) ethanol | BASF SE, Intermediates Division | 2-(2-Aminoethoxy) ethanol is a building block for the modification of epoxy resins. 2-(2-Aminoethoxy) ethanol modified epoxy resins are suited for cationic electro deposition coatings. | |
| 2-Ethyl-4-Methylimidazole | BASF SE, Intermediates Division | 2-Ethyl-4-Methylimidazole is a selective catalyst for epoxy and urethane reactions. 2-Ethyl-4-methylimidazole is used for two components epoxy systems, for the modification of epoxy resins and for preparation of polyurethanes. | |
| 2-Ethylhexanoic Acid, 2-EHA | BASF SE, Intermediates Division | 2-Ethylhexanoic Acid, 2-EHA is a building block for alkyd resins and for production of organic metal salts. Alkyd resins modified with 2-ethylhexanoic acid are used in stoving enamels and two-component paints (primers and topcoats). Metal salts of 2-ethy...voir plus 2-Ethylhexanoic Acid, 2-EHA is a building block for alkyd resins and for production of organic metal salts. Alkyd resins modified with 2-ethylhexanoic acid are used in stoving enamels and two-component paints (primers and topcoats). Metal salts of 2-ethylhexanoic acid are used for siccatives in oxidative drying paints and printing inks. voir moins | |
| 2-Ethylhexylvinylether, EHVE | BASF SE, Intermediates Division | 2-Ethylhexylvinylether, EHVE is a monomer for copolymers with vinyl chlorides (Laroflex®) or TFCE 1,1,2-trifluoro-2-chloroethene. Copolymers with 2-Ethylhexyl vinyl ether are used for solvent based anti-corrosion coatings. Vinyl ethers form alternating co...voir plus 2-Ethylhexylvinylether, EHVE is a monomer for copolymers with vinyl chlorides (Laroflex®) or TFCE 1,1,2-trifluoro-2-chloroethene. Copolymers with 2-Ethylhexyl vinyl ether are used for solvent based anti-corrosion coatings. Vinyl ethers form alternating copolymers via charge transfer-complex polymerization with electron-deficient monomers, such as vinyl chlorides, maleic anhydride, TFCE, resulting in better solubility and flexibility. voir moins | |
| 2-Ethylimidazole | BASF SE, Intermediates Division | 2-Ethylimidazole is a selective catalyst for epoxy and urethanes reactions. 2-Ethylimidazole is used for two components epoxy systems; for modification of epoxy resins and for preparation of polyurethanes. | |
| 2-Mercaptoethanol | BASF SE, Intermediates Division | 2-Mercaptoethanol application fields include, tin type of stabilizer, chain transfer agent in polymerization processes, and anti-corrosion systems for oilfields. Mercaptoethanol is used in acrylic resin production of water-borne coatings. | |
| 2-Methylimidazole | BASF SE, Intermediates Division | 2-Methylimidazole is a selective catalyst for epoxy and urethane reactions. 2-Methylimidazole is used for two components epoxy systems; for the modification of epoxy resins and for the preparation of polyurethanes. | |
| 2,4,7,9-Tetramethyl-decyne-5-diol-4,7, TMDD | BASF SE, Intermediates Division | 2,4,7,9-Tetramethyl-Decyne-5-Diol-4,7, TMDD is an antifoaming and wetting agent for water-borne coatings and inks. TMDD is suitable for all water-borne coatings (ED-coatings, water-borne stoving enamels, water-borne house and wall paints) and inks. | |
| 3-(Cyclohexylamino) propylamine | BASF SE, Intermediates Division | 3-(Cyclohexylamino) propylamine is a cross linker for epoxy resins. 3-Cyclohexylaminopropylamine is suitable for two-component epoxy coatings and for epoxy-based plastic parts. 3-Cyclohexylaminopropylamine is very compatible with co-resins and improves ...voir plus 3-(Cyclohexylamino) propylamine is a cross linker for epoxy resins. 3-Cyclohexylaminopropylamine is suitable for two-component epoxy coatings and for epoxy-based plastic parts. 3-Cyclohexylaminopropylamine is very compatible with co-resins and improves resistance against humidity during film formation. voir moins | |
| 3-(Dimethylamino) propylamine | BASF SE, Intermediates Division | 3-(Dimethylamino) propylamine is a building block for modification of epoxy resins. 3-(Dimethylamino) propylamine modified epoxy resins are used for cationic electro deposition coatings. | |
| 3,3'-Dimethyl-4,4'-diamino-dicyclohexyl-methan | BASF SE, Intermediates Division | 3,3'-Dimethyl-4,4'-diamino-dicyclohexyl-methan is a cross linker for epoxy resins, building block for polyamides and polyurethanes. 2,2'-Dimethyl-4,4'-methylene bis(cyclohexylamine)is suitable for two-component epoxy coatings, for epoxy-based adhesives a...voir plus 3,3'-Dimethyl-4,4'-diamino-dicyclohexyl-methan is a cross linker for epoxy resins, building block for polyamides and polyurethanes. 2,2'-Dimethyl-4,4'-methylene bis(cyclohexylamine)is suitable for two-component epoxy coatings, for epoxy-based adhesives and epoxy composites. The hydrophobic structure of 2,2'-Dimethyl-4,4'-methylene bis(cyclohexylamine) improves the hydrolytical resistance, increases reactivity and compatibility in epoxy coatings. voir moins | |
| 4-Hydroxybutyl vinyl ether (HBVE) | BASF SE, Intermediates Division | 4-Hydroxybutyl vinyl ether (HBVE) is a building block for macro monomers and monomer for vinyl copolymers, reactive diluents for UV coatings. Ethoxylatated HBVE is used as a monomer for concrete additive. Used for water and solvent based hydroxyfunction...voir plus 4-Hydroxybutyl vinyl ether (HBVE) is a building block for macro monomers and monomer for vinyl copolymers, reactive diluents for UV coatings. Ethoxylatated HBVE is used as a monomer for concrete additive. Used for water and solvent based hydroxyfunctional vinyl polymers, which are cross-linked with polyisocyanates and melamine resins. voir moins | |
| 4,4'-Diaminodicyclo-hexylmethane | BASF SE, Intermediates Division | 4,4'-Diaminodicyclo-hexylmethane is a cross linker for epoxy resins, building block for polyamides. Diaminodicyclo-hexylmethane is used for two-component epoxy coatings and for epoxy-based adhesives. Diaminodicyclo-hexylmethane ensures an optimal balanc...voir plus 4,4'-Diaminodicyclo-hexylmethane is a cross linker for epoxy resins, building block for polyamides. Diaminodicyclo-hexylmethane is used for two-component epoxy coatings and for epoxy-based adhesives. Diaminodicyclo-hexylmethane ensures an optimal balance of hardness and flexibility. voir moins | |
| 4,4'-Methylenedianiline, MDA | BASF SE, Intermediates Division | 4,4'-Methylenedianiline, MDA is a building block for polyimides, polyamideimides, polyesterimides, special cross linker agent for epoxy resins. Polyimides, polyamideinmides, and polyesterimides resins based on 4,4'-Methylenedianiline can be used for elect...voir plus 4,4'-Methylenedianiline, MDA is a building block for polyimides, polyamideimides, polyesterimides, special cross linker agent for epoxy resins. Polyimides, polyamideinmides, and polyesterimides resins based on 4,4'-Methylenedianiline can be used for electro insulation coatings, 4,4'-Methylenedianiline is also used as epoxy cross linker for special epoxy powder coatings. voir moins | |
| 4,7,10-Trioxatridecan- 1,13-diamine | BASF SE, Intermediates Division | 4,7,10-Trioxatridecan- 1,13-diamine is a cross linker for epoxy resins, building block for polyurethanes and polyureas. 4,7,10-Trioxatridecan-1,13-diamine is suitable for two-component epoxy coatings and can be combined with polyisocyanate adducts for po...voir plus 4,7,10-Trioxatridecan- 1,13-diamine is a cross linker for epoxy resins, building block for polyurethanes and polyureas. 4,7,10-Trioxatridecan-1,13-diamine is suitable for two-component epoxy coatings and can be combined with polyisocyanate adducts for polyurea coatings. It also improves the flexibility of coatings. voir moins | |
| 4,9-Dioxadodecan- 1,12-diamine | BASF SE, Intermediates Division | 4,9-Dioxadodecan- 1,12-diamine is a cross linker for epoxy resins, building block for polyurethanes and polyureas. 4,9-Dioxadodecan-1,12-diamine is suitable for two-component epoxy coatings and can be combined with polyisocyanate adducts for polyurea coa...voir plus 4,9-Dioxadodecan- 1,12-diamine is a cross linker for epoxy resins, building block for polyurethanes and polyureas. 4,9-Dioxadodecan-1,12-diamine is suitable for two-component epoxy coatings and can be combined with polyisocyanate adducts for polyurea coatings. It also improves the flexibility of coatings. voir moins | |
| Baxxodur™ EC 201 | BASF SE, Intermediates Division | Baxxodur™ EC 201 is a cycloaliphatic amine based curing agent with low viscosity and moderate reactivity. Applications include, structural adhesive, flooring, grout, coating in construction, composite lamination, casting and encapsulation, and heavy duty ...voir plus Baxxodur™ EC 201 is a cycloaliphatic amine based curing agent with low viscosity and moderate reactivity. Applications include, structural adhesive, flooring, grout, coating in construction, composite lamination, casting and encapsulation, and heavy duty protective coating. voir moins | |
| Baxxodur™ EC 301 | BASF SE, Intermediates Division | Baxxodur™ 301 is a polyether amine based curing agent with low viscosity and long pot life. Applications include, structural adhesive, construction, composite lamination casting and encapsulation, decorative and protective coating. | |
| Baxxodur™ EC 302 | BASF SE, Intermediates Division | Baxxodur™ 302 is a polyether amine based curing agent with low viscosity and long pot life. Applications include, composite, structural adhesive and epoxy toughener. | |
| Baxxodur™ EC 110 | BASF SE, Intermediates Division | Baxxodur™ EC 110 is an aliphatic amine based fast curing agent with low viscosity. Applications include, epoxy grout in construction, epoxy coating in marine and maintenance, casting and encapsulation, composite lamination, intermediate for polyamide. | |
| Baxxodur™ EC 130 | BASF SE, Intermediates Division | Baxxodur™ EC 130 is a polyether amine based curing agent with low viscosity and high reactivity. Applications include, structural adhesive and composite lamination. | |
| Baxxodur™ EC 252 | BASF SE, Intermediates Division | Baxxodur™ EC 252 is a cycloaliphatic amine based curing agent with very low viscosity and moderate reactivity. Applications include structural adhesive, heavy duty epoxy coating, composite lamination, casting and encapsulation, epoxy prepreg. | |
| Benox® B50-106 | UNITED INITIATORS GMBH & CO KG | Benox® B50-106 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy white paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent and polyme...voir plus Benox® B50-106 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy white paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, and unsaturated polyester/vinyl ester resins. Benox® B50-106 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B50-210 | UNITED INITIATORS GMBH & CO KG | Benox® B50-210 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy blue pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent a...voir plus Benox® B50-210 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy blue pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, and unsaturated polyester/vinyl ester resins. Benox® B50-210 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B50-230 | UNITED INITIATORS GMBH & CO KG | Benox® B50-230 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy lighter blue pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing...voir plus Benox® B50-230 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy lighter blue pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, and unsaturated polyester/vinyl ester resins. Benox® B50-230 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B50-513 | UNITED INITIATORS GMBH & CO KG | Benox® B50-513 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy red pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used as a curing agent and polymerization initiato...voir plus Benox® B50-513 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy red pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, and unsaturated polyester/vinyl ester resins. Benox® B50-513 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B50-713 | UNITED INITIATORS GMBH & CO KG | Benox® B50-713 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy onyx pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent a...voir plus Benox® B50-713 is a fine dispersion of 50% dibenzoyl peroxide in a smooth, non-separating fire resistant creamy onyx pigmented paste form. It can freely be dissolved in monomers and resins and is primarily used with auto body filler or as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, and unsaturated polyester/vinyl ester resins. Benox® B50-713 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B55 | UNITED INITIATORS GMBH & CO KG | Benox® B55 is a fine dispersion of dibenzoyl peroxide in a smooth, non-separating fire resistant creamy paste form with a white or red thixotropic cream appearance. It can freely be dissolved in monomers and resins and is primarily used as a curing agent ...voir plus Benox® B55 is a fine dispersion of dibenzoyl peroxide in a smooth, non-separating fire resistant creamy paste form with a white or red thixotropic cream appearance. It can freely be dissolved in monomers and resins and is primarily used as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, and unsaturated polyester/vinyl ester resins. Benox® B55 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B55-107 | UNITED INITIATORS GMBH & CO KG | Benox® B55-107 is a fine dispersion of 55% dibenzoyl peroxide in a smooth, non-separating fire resistant white paste form. It is formulated primarily for use in industries which require a product to be further diluted prior to use and in the mine bolt ind...voir plus Benox® B55-107 is a fine dispersion of 55% dibenzoyl peroxide in a smooth, non-separating fire resistant white paste form. It is formulated primarily for use in industries which require a product to be further diluted prior to use and in the mine bolt industry. Benox® B55-107 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® B55-108 | UNITED INITIATORS GMBH & CO KG | Benox® B55-108 is a fine dispersion of 55% dibenzoyl peroxide in a smooth, non-separating fire resistant white paste form. It is formulated primarily for use in elevated and ambient temperature curing of unsaturated polyester resins and is characterized b...voir plus Benox® B55-108 is a fine dispersion of 55% dibenzoyl peroxide in a smooth, non-separating fire resistant white paste form. It is formulated primarily for use in elevated and ambient temperature curing of unsaturated polyester resins and is characterized by its lower water content, compared to Benox® B55-107. Benox® B55-108 can also be used in two-part adhesive systems based on methacylate or polyester resins. voir moins | |
| Benox® L-50E | UNITED INITIATORS GMBH & CO KG | Benox® L-50E, in the form of a smooth water white low viscosity fire resistant creamy paste, is a fine dispersion of dibenzoyl peroxide. It can be readily dissolved in monomers and resins, is less hazardous, and is easier to use than dry or technical form...voir plus Benox® L-50E, in the form of a smooth water white low viscosity fire resistant creamy paste, is a fine dispersion of dibenzoyl peroxide. It can be readily dissolved in monomers and resins, is less hazardous, and is easier to use than dry or technical forms of dibenzoyl peroxide (provided the water content and plasticizer are not objectionable. Benox® L-50E is primarily used as a curing agent and polymerization initiator for acrylic, monomeric vinyl, styrene, co-polymers, unsaturated polyester/vinyl ester resins, and copolymers of these resins. It can also be used in two-part adhesive systems, based on methacrylate or polyester resins, where the creamy consistency allows uniform mixing of the components. voir moins | |
| Benzylamine | BASF SE, Intermediates Division | Benzylamine is a building block for crystalline ureas. Crystalline ureas based on benzylamine act as sag control agents for stoving enamels. | |
| Capromer™ PD1–10 | BASF SE, Intermediates Division | Capromer™ PD1–10 is a polycaprolactone based polyester polyol for polyurethane based coatings. The difunctional product is based on Neopentyl glycol with a molecular weight of 1000. It is used where the unique combination of properties including hydroly...voir plus Capromer™ PD1–10 is a polycaprolactone based polyester polyol for polyurethane based coatings. The difunctional product is based on Neopentyl glycol with a molecular weight of 1000. It is used where the unique combination of properties including hydrolytic stability, excellent weatherability, good dynamic characteristics, and outstanding low temperature flexibility is desired. PolyCLO products are designed for use in cast and TPU elastomers, adhesives, reactive diluents, and resin intermediates. voir moins | |
| Capromer™ PD1–10 A | BASF SE, Intermediates Division | Capromer™ PD1–10 A offers low color, good hydrolytic stability and weatherability. During manufacturing, PolyCLO provides an improved processability due to the low viscosity, high purity, exact functionality, and consistent reactivity. PolyCLO products...voir plus Capromer™ PD1–10 A offers low color, good hydrolytic stability and weatherability. During manufacturing, PolyCLO provides an improved processability due to the low viscosity, high purity, exact functionality, and consistent reactivity. PolyCLO products are designed for the use in cast and TPU elastomers, adhesives, reactive diluents, and resin intermediates. voir moins | |
| Capromer™ PD1–20 | BASF SE, Intermediates Division | Capromer™ PD1–20 is a polycaprolactone based polyester polyol for polyurethane based coatings. The difunctional product is based on Neopentyl glycol with a molecular weight of 2000. It is used where the unique combination of properties including hydroly...voir plus Capromer™ PD1–20 is a polycaprolactone based polyester polyol for polyurethane based coatings. The difunctional product is based on Neopentyl glycol with a molecular weight of 2000. It is used where the unique combination of properties including hydrolytic stability, excellent weatherability, good dynamic characteristics, and outstanding low temperature flexibility is desired. PolyCLO products are designed for the use in cast and TPU elastomers, adhesives, reactive diluents, and resin intermediate voir moins | |
| Capromer™ PD1–20 A | BASF SE, Intermediates Division | Capromer™ PD1–20 A offers low color, good hydrolytic stability and weatherability. During manufacturing, PolyCLO provides an improved processability due to the low viscosity, high purity, exact functionality, and consistent reactivity. PolyCLO product...voir plus Capromer™ PD1–20 A offers low color, good hydrolytic stability and weatherability. During manufacturing, PolyCLO provides an improved processability due to the low viscosity, high purity, exact functionality, and consistent reactivity. PolyCLO products are designed for the use in cast and TPU elastomers, adhesives, reactive diluents, and resin intermediates. voir moins | |
| Capromer™ PD4-05 (PolyCLO DEG550) | BASF SE, Intermediates Division | Capromer™ PD4-05 (PolyCLO DEG550) is a polycaprolactone based polyester polyol for polyurethane based coatings. The difunctional product is based on Diethylene glycol with a molecular weight of 550. It is used where the unique combination of properties i...voir plus Capromer™ PD4-05 (PolyCLO DEG550) is a polycaprolactone based polyester polyol for polyurethane based coatings. The difunctional product is based on Diethylene glycol with a molecular weight of 550. It is used where the unique combination of properties including hydrolytic stability, excellent weatherability, good dynamic characteristics, and outstanding low temperature flexibility is desired. PolyCLO products are designed for the use in cast and TPU elastomers, adhesives, reactive diluents, and resin intermediate. voir moins | |
| Capromer™ PT1–05 (PolyCLO TMP540) | BASF SE, Intermediates Division | Capromer™ PT1–05 (PolyCLO TMP540) is a polycaprolactone based polyester polyol for polyurethane based coatings and adhesives. The trifunctional product is based on Trimethylolpropane a molecular weight of 540. It is used where the unique combination of ...voir plus Capromer™ PT1–05 (PolyCLO TMP540) is a polycaprolactone based polyester polyol for polyurethane based coatings and adhesives. The trifunctional product is based on Trimethylolpropane a molecular weight of 540. It is used where the unique combination of properties including hydrolytic stability, excellent weatherability, good dynamic characteristics, and outstanding low temperature flexibility is desired. PolyCLO products are designed for the use in cast and TPU elastomers, adhesives, reactive diluents, and resin intermediates voir moins | |
| Crestabond® M1-04 | Scott Bader | Crestabond® M1-04 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M1-04 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M1-05 | Scott Bader | Crestabond® M1-05 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M1-05 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M1-20 | Scott Bader | Crestabond® M1-20 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M1-20 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M1-30 | Scott Bader | Crestabond® M1-30 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M1-30 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M1-60 | Scott Bader | Crestabond® M1-60 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M1-60 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M1-90 | Scott Bader | Crestabond® M1-90 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M1-90 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M7-05 | Scott Bader | Crestabond® M7-05 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating...voir plus Crestabond® M7-05 is a primerless two component acrylic adhesive designed for bonding composites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestabond® M7-15 | Scott Bader | Crestabond® M7-15 is a primerless two component acrylic adhesive designed for bonding compoisites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstratin...voir plus Crestabond® M7-15 is a primerless two component acrylic adhesive designed for bonding compoisites, thermoplastics, and metals. This new generation of structural methacrylate adhesive meets the bonding requirements of most assembly operations, demonstrating excellent impact, peel, shear, compressive strength, and fatigue resistance properties across all bonded parts. voir moins | |
| Crestomer® 1150PA | Scott Bader | Crestomer® 1150PA is a highly thixotropic structural adhesive that is pre-accelerated and based on unsaturated urethane acrylate in styrene monomer. It displays good adhesion and high elongation at break, shows no sagging on vertical surfaces and has good...voir plus Crestomer® 1150PA is a highly thixotropic structural adhesive that is pre-accelerated and based on unsaturated urethane acrylate in styrene monomer. It displays good adhesion and high elongation at break, shows no sagging on vertical surfaces and has good fatigue and impact resistance properties. Crestomer® 1150PA is mostly used in structural composite applications and has good adhesion to FRP laminates, wood and some metals as well as core materials. Crestomer® 1150PA can be used for bonding diesel tanks and contour joints in FRP components. voir moins | |
| Crestomer® 1151A | Scott Bader | Crestomer® 1151A is a structural adhesive and filleting compound that is fast curing, non-sagging and bonds a variety of substrates with little surface preparation. It has a lower odor than other competing structural adhesives and is based on innovative u...voir plus Crestomer® 1151A is a structural adhesive and filleting compound that is fast curing, non-sagging and bonds a variety of substrates with little surface preparation. It has a lower odor than other competing structural adhesives and is based on innovative urethane acrylate technology. Crestomer® 1151A shows good impact strength and toughness as well as exhibiting good adhesion and gap filling properties that enables the user greater flexibility in design, saving time and money. The adhesive is especially formulated for use in bulk metering systems. voir moins | |
| Crestomer® 1152PA | Scott Bader | Crestomer® 1152PA is a two part pre-accelerated structural adhesive that is highly thixotropic and is based on unsaturated urethane acrylate in styrene monomer. It displays good adhesion to core materials, wood, FRP laminates and some metals and because o...voir plus Crestomer® 1152PA is a two part pre-accelerated structural adhesive that is highly thixotropic and is based on unsaturated urethane acrylate in styrene monomer. It displays good adhesion to core materials, wood, FRP laminates and some metals and because of its good adhesion properties, Crestomer® 1152PA can be recommended for use as a general purpose adhesive. It can also be used to bond contour joints in FRP components, to bond diesel tanks as well as bonding damaged areas or "green" FRP. voir moins | |
| Crestomer® 1153PA | Scott Bader | Crestomer® 1153PA is a structural adhesive that is highly thixotropic and derived from unsaturated urethane acrylate in styrene monomer. The adhesive has a long open time of 90 minutes and shows good adhesion to core materials, metals, wood and FRP lamina...voir plus Crestomer® 1153PA is a structural adhesive that is highly thixotropic and derived from unsaturated urethane acrylate in styrene monomer. The adhesive has a long open time of 90 minutes and shows good adhesion to core materials, metals, wood and FRP laminates. Because of its good adhesion properties, Crestomer® 1153PA is ideal for use as a general purpose adhesive. The adhesive is also used to contour joints in FRP components, to bond "green" FRP and to build up damaged areas. Crestomer® 1153PA is mainly used in structural composite applications. voir moins | |
| Crestomer® 1186PA | Scott Bader | Crestomer® 1186PA is a structural adhesive from unique unsaturated urethane acrylate that shows resistance to crack propagation, toughness and good impact strength. It displays good adhesion to a variety of metals, polymeric materials and ceramics and off...voir plus Crestomer® 1186PA is a structural adhesive from unique unsaturated urethane acrylate that shows resistance to crack propagation, toughness and good impact strength. It displays good adhesion to a variety of metals, polymeric materials and ceramics and offers structural adhesion even when bonding FRP laminates with a 30mm thick bondline. The multi-purpose gap filling structural adhesive is used in a variety of FRP applications. voir moins | |
| Crestomer® 1196PA | Scott Bader | Crestomer® 1196PA is a low denisty core bonding structural adhesive based on unique urethane acrylate technology that displays outstanding strength and toughness. The adhesive is designed to bond core materials like balsa and rigid PVC foam to semi-cured ...voir plus Crestomer® 1196PA is a low denisty core bonding structural adhesive based on unique urethane acrylate technology that displays outstanding strength and toughness. The adhesive is designed to bond core materials like balsa and rigid PVC foam to semi-cured or cured FRP skins. It also displays a tougher and more durable structural bond than a polyester bonding adhesive or a polyester resin/glass structure. Crestomer® 1196PA also exhibits reduced styrene emissions, great weight savings and more improved cosmetics with the ridding of core print through. Crestomer® 1196PA is suited for use in sandwich construction where the needs are for a high impact-resistant, strong and tough structure. voir moins | |
| Crestomer® Advantage 30 | Scott Bader | Crestomer® Advantage 30 is a structural adhesive that is white in color and bonds with a variety of substrates with less surface preparation and a lower odor than competitive materials. It has a quick gel time of 30 minutes and bonded parts can be used in...voir plus Crestomer® Advantage 30 is a structural adhesive that is white in color and bonds with a variety of substrates with less surface preparation and a lower odor than competitive materials. It has a quick gel time of 30 minutes and bonded parts can be used in 2 hours and 20 minutes. It is based on unique urethane acrylate technology and displays good impact strength and toughness. With the strong adhesion and gap filling qualities shown by Crestomer® Advantage 30, great flexibility in design is offered, along with time and cost savings. voir moins | |
| Crystic® BP 621CC 30 | Scott Bader | Crystic® BP 621CC 30 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound i...voir plus Crystic® BP 621CC 30 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound is specifically designed for the assembly and bonding of GRP mouldings - including panels, inserts, internal frames, composite constructions, and car body components. voir moins | |
| Crystic® BP 621CC 45 | Scott Bader | Crystic® BP 621CC 45 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound i...voir plus Crystic® BP 621CC 45 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound is specifically designed for the assembly and bonding of GRP mouldings - including panels, inserts, internal frames, composite constructions, and car body components. voir moins | |
| Crystic® BP 621CC 65 | Scott Bader | Crystic® BP 621CC 65 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound i...voir plus Crystic® BP 621CC 65 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound is specifically designed for the assembly and bonding of GRP mouldings - including panels, inserts, internal frames, composite constructions, and car body components. voir moins | |
| Crystic® BP 621CC White 20 | Scott Bader | Crystic® BP 621CC White 20 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste with a final product colour of white. It offers high shear strength for bonded joints, eliminating the need for mechanical f...voir plus Crystic® BP 621CC White 20 is a preaccelerated, urethane acrylate- and isophthalic polyester-based, high performance bonding paste with a final product colour of white. It offers high shear strength for bonded joints, eliminating the need for mechanical fixings. This non-sagging, filled compound is specifically designed for the assembly and bonding of GRP mouldings - including panels, inserts, internal frames, composite constructions, and car body components. voir moins | |
| Crystic® BP 90-78PA | Scott Bader | Crystic® BP 90-78PA is a white, preaccelerated, orthophthalic polyester bonding paste featuring high thixotropy, fast curing, good handling characteristics, and ease of application. This non-sagging, filled compound is specifically designed for the assemb...voir plus Crystic® BP 90-78PA is a white, preaccelerated, orthophthalic polyester bonding paste featuring high thixotropy, fast curing, good handling characteristics, and ease of application. This non-sagging, filled compound is specifically designed for the assembly and bonding of GRP mouldings - including panels, insert frames, ribs, and other non-structural bonding applications. voir moins | |
| Crystic® BP 90-79PA | Scott Bader | Crystic® BP 90-79PA is a grey, preaccelerated, orthophthalic polyester bonding paste featuring high thixotropy, fast curing, good handling characteristics, and ease of application. This non-sagging, filled compound is specifically designed for the assembl...voir plus Crystic® BP 90-79PA is a grey, preaccelerated, orthophthalic polyester bonding paste featuring high thixotropy, fast curing, good handling characteristics, and ease of application. This non-sagging, filled compound is specifically designed for the assembly and bonding of GRP mouldings - including panels, insert frames, ribs, and other non-structural bonding applications. voir moins | |
| Crystic® BP 90-80PA | Scott Bader | Crystic® BP 90-80PA is a pre-accelerated polyester bonding paste, consisting of a viscous, filled compound containing short glass fibers and flexible and low shrink additives. It features high shear strength, high thixotropy, and improved overall mechanic...voir plus Crystic® BP 90-80PA is a pre-accelerated polyester bonding paste, consisting of a viscous, filled compound containing short glass fibers and flexible and low shrink additives. It features high shear strength, high thixotropy, and improved overall mechanical properties. This product is specifically designed for the assembly and bonding of GRP moldings - including internal frames, inserts, ribs, panels, composite constructions, and car body components. voir moins | |
| Crystic® BP 90-82PA | Scott Bader | Crystic® BP 90-82PA is a pre-accelerated polyester bonding paste, consisting of a viscous, white, filled compound containing a flexible additive. It features high shear strength, high thixotropy, and improved impact resistance. This product is specificall...voir plus Crystic® BP 90-82PA is a pre-accelerated polyester bonding paste, consisting of a viscous, white, filled compound containing a flexible additive. It features high shear strength, high thixotropy, and improved impact resistance. This product is specifically designed for the assembly and bonding of GRP moldings - including panels, inserts, internal frames, ribs, composite constructions, and car body components. voir moins | |
| Crystic® BP 90-83PA | Scott Bader | Crystic® BP 90-83PA is a pre-accelerated orthophathlic polyester bonding paste consisting of a non-sagging, filled compound. Key features include ease of application, high thixotropy, and good handling characteristics. This product is specifically design...voir plus Crystic® BP 90-83PA is a pre-accelerated orthophathlic polyester bonding paste consisting of a non-sagging, filled compound. Key features include ease of application, high thixotropy, and good handling characteristics. This product is specifically designed for the assembly and bonding of GRP moldings, including internal frames, inserts, ribs, panels, and other non-structural bonding applications. voir moins | |
| Crystic® BP 90-83PAHV | Scott Bader | Crystic® BP 90-83PAHV is a low exotherm, preaccelerated polyester bonding paste consisting of a viscous, filled compound. It features high thixotropy, low shrink properties, good handling characteristics, and no print through. This product is specifically...voir plus Crystic® BP 90-83PAHV is a low exotherm, preaccelerated polyester bonding paste consisting of a viscous, filled compound. It features high thixotropy, low shrink properties, good handling characteristics, and no print through. This product is specifically designed for the assembly and bonding of GRP mouldings - including panels, inserts, internal frames, ribs, composite constructions, and car body components. voir moins | |
| Crystic® BP 90-84PA | Scott Bader | Crystic® BP 90-84PA is a lightweight, low exotherm, pre-accelerated, orthophthalic polyester bonding paste consisting of a non-sagging compound. It features high thixotropy, low specific gravity, good handling characteristics, and a visual check for effec...voir plus Crystic® BP 90-84PA is a lightweight, low exotherm, pre-accelerated, orthophthalic polyester bonding paste consisting of a non-sagging compound. It features high thixotropy, low specific gravity, good handling characteristics, and a visual check for effective catalyst mix. This product is designed for non-structural applications where gap filling may be a secondary requirement. voir moins | |
| Crystic® BP 91-21PA | Scott Bader | Crystic® BP 91-21PA is a preaccelerated isophthalic polyester bonding paste, in the form of a viscous, filled compound. Benefits include high shear strength, increased water resistance, and improved overall mechanical properties. This product is specifica...voir plus Crystic® BP 91-21PA is a preaccelerated isophthalic polyester bonding paste, in the form of a viscous, filled compound. Benefits include high shear strength, increased water resistance, and improved overall mechanical properties. This product is specifically designed for the assembly and bonding of GRP mouldings - including panels, inserts, internal frames, hull-to-deck assemblies, composite constructions, and car body components. voir moins | |
| Crystic® Scottbond 102PA White | Scott Bader | Crystic® Scottbond 102PA White is a white-colored pourable adhesive paste that is from a specially selected unsaturated polyester resin that is pre-accelerated to offer a convenient working time. The resin-based adhesive has a thixotropic polyester and is...voir plus Crystic® Scottbond 102PA White is a white-colored pourable adhesive paste that is from a specially selected unsaturated polyester resin that is pre-accelerated to offer a convenient working time. The resin-based adhesive has a thixotropic polyester and is meant for bonding GRP to rigid polyurethane foam in sandwich panel systems. Crystic® Scottbond 102PA is also used to bond GRP to plywood and plywood to polyurethane foam. It is designed to ensure ease of application and spreads easily under pressure, presenting a smoother surface in the finished product. However, it should not soak or drain too much into the polyurethane foam. Some penetration is necessary to ensure adhesion. voir moins | |
| Crystic® Scottbond 117PA | Scott Bader | Crystic® Scottbond 117PA is a high quality orthophthalic polyester resin in a gap filling adhesive paste that has been pre-accelerated to offer a convenient working time. The bonding paste is recognized as having the ability to bond most materials that a...voir plus Crystic® Scottbond 117PA is a high quality orthophthalic polyester resin in a gap filling adhesive paste that has been pre-accelerated to offer a convenient working time. The bonding paste is recognized as having the ability to bond most materials that are standard in the GRP industry. Crystic® Scottbond 117PA shows good adhesion to GRP laminates, offering a stronger bond compared to resin and glass fiber in the laminate. voir moins | |
| CUMAR® 105 | Neville Chemical Company | CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne ...voir plus CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne and epoxy based coatings, IV ink modifiers, adhesives and sealants. voir moins | |
| Cyclohexyl vinyl ether, CHVE | BASF SE, Intermediates Division | Cyclohexyl vinyl ether, CHVE monomer for copolymers with vinyl chlorides (Laroflex®) or TFCE 1,1,2-trifluoro-2-chloroethene. Vinyl ethers form alternating copolymers via charge transfer-complex polymerization with electron-deficient monomers, such as vin...voir plus Cyclohexyl vinyl ether, CHVE monomer for copolymers with vinyl chlorides (Laroflex®) or TFCE 1,1,2-trifluoro-2-chloroethene. Vinyl ethers form alternating copolymers via charge transfer-complex polymerization with electron-deficient monomers, such as vinyl chlorides, maleic anhydride, TFCE, resulting in better solubility and flexibility. Copolymers with Cyclohexyl vinyl ether are used for solvent based anti-corrosion coatings. voir moins | |
| Diazabicylooctane (DABCO) Lupragen® N 201, N 202, N 203 | BASF SE, Intermediates Division | Diazabicylooctane (DABCO) Lupragen® N 201, N 202, N 203 catalyst for urethane reactions. Diazabicyclooctane is suitable for production of polyurethanes and as catalyst for two-components paints (automotive OEM and repair paints, plastic paints and paints...voir plus Diazabicylooctane (DABCO) Lupragen® N 201, N 202, N 203 catalyst for urethane reactions. Diazabicyclooctane is suitable for production of polyurethanes and as catalyst for two-components paints (automotive OEM and repair paints, plastic paints and paints for general industry). voir moins | |
| Diethanolamine, pure | BASF SE, Intermediates Division | Diethanolamine, pure is a neutralisation agent for water based coatings, building block for the modification of epoxy resins and polyurethanes. Diethanolamine modified epoxy resins are used for cationic electro deposition coatings. | |
| Diethylene triamine | BASF SE, Intermediates Division | Diethylene triamine is a cross linker for epoxy resins, building block to modify epoxy resins. Diethylene triamine is used for two-component epoxy coatings and for epoxy composites. Modified epoxy resins with diethylene triamine are used for cationic ele...voir plus Diethylene triamine is a cross linker for epoxy resins, building block to modify epoxy resins. Diethylene triamine is used for two-component epoxy coatings and for epoxy composites. Modified epoxy resins with diethylene triamine are used for cationic electro deposition coatings (CED-coating). voir moins | |
| Diethyleneglycol divinyl ether, DVE-2 | BASF SE, Intermediates Division | Diethyleneglycol divinyl ether is a reactive diluent for unsaturated poly-esters, UV coatings, UV inks, UV adhesives and release coatings. It is a crosslinker for Polyacrylate polymers used as ion exchange resins. It is a building block for sulfur based ...voir plus Diethyleneglycol divinyl ether is a reactive diluent for unsaturated poly-esters, UV coatings, UV inks, UV adhesives and release coatings. It is a crosslinker for Polyacrylate polymers used as ion exchange resins. It is a building block for sulfur based sealant compounds. Diethyleneglycol divinyl ether performs low viscosity in UV-coatings, especially in cationic polymerization. with no labeling, no risk phrases . voir moins | |
| Diisopropanolamine | BASF SE, Intermediates Division | Diisopropanolamine is a neutralization agent for anionic stabilized resins, building block for polyurethanes. Diisopropanolamine is suitable for waterborne stoving enamels based on polyesters, alkyds and acrylic resins (secondary dispersions). Diisoprop...voir plus Diisopropanolamine is a neutralization agent for anionic stabilized resins, building block for polyurethanes. Diisopropanolamine is suitable for waterborne stoving enamels based on polyesters, alkyds and acrylic resins (secondary dispersions). Diisopropanolamine supports the film forming of stoving enamels. voir moins | |
| epsilon-Caprolactone, CLO | BASF SE, Intermediates Division | Epsilon-Caprolactone, CLO can be used as an intermediate for two-components paints for plastic coatings and automotive repair coatings, for poly-urethane dispersions for waterborne coatings and for UV-coatings. Epsilon-Caprolactone, CLO with a combinatio...voir plus Epsilon-Caprolactone, CLO can be used as an intermediate for two-components paints for plastic coatings and automotive repair coatings, for poly-urethane dispersions for waterborne coatings and for UV-coatings. Epsilon-Caprolactone, CLO with a combination of flexibility and hardness (toughness) epsilon-Caprolactone can provide special mechanical properties in segmented polymers. voir moins | |
| Ethylene diamine | BASF SE, Intermediates Division | Ethylene diamine is a cross linker for epoxy resins, building block for polyamides and polyurethanes. Ethylene diamine is frequently used in epoxy coatings and adhesives as well as in epoxy composites. In addition, it can be used as chain extender for wa...voir plus Ethylene diamine is a cross linker for epoxy resins, building block for polyamides and polyurethanes. Ethylene diamine is frequently used in epoxy coatings and adhesives as well as in epoxy composites. In addition, it can be used as chain extender for waterborne polyurethane dispersions. Alkyds containing isononanoic acid are distinguished by optimal solubility and compatibility, weather- and yellowing resistance and hydrophobicity. voir moins | |
| Ethylene urea, N,N'-Ethyleneurea, 2-Imidozolidone | BASF SE, Intermediates Division | Ethylene urea, N,N'-Ethyleneurea, 2-Imidozolidone is effective formaldehyde scavenger in amino-resins like urea-formaldehyde (UF), melamine-formaldehyde (MF) or melamine-urea-formaldehyde (MUF) condensates. | |
| Formic acid | BASF SE, Intermediates Division | Formic acid is an additive for coatings and a neutralization agent (i.e. cationic electro deposition paints). Formic acid is used in resin production for CED-resins. | |
| Hydroxypivalic acid neopentylglycolester, HPN | BASF SE, Intermediates Division | Hydroxypivalic acid neopentylglycolester, HPN is a building block for saturated polyesters, unsaturated polyesters and polyurethanes. HPN is suitable for polyesters for solvent-borne paints (stoving enamels for can-& coil-coating, automotive coatings, co...voir plus Hydroxypivalic acid neopentylglycolester, HPN is a building block for saturated polyesters, unsaturated polyesters and polyurethanes. HPN is suitable for polyesters for solvent-borne paints (stoving enamels for can-& coil-coating, automotive coatings, coatings for industrial applications) and for two-component paints (plastic coatings, repair coatings). HPN polyesters are used preferentially used for waterborne paints, but also suitable for polyesters in powder coatings. HPN shows high reactivity for esterification and trans-esterification. HPN introduces optimal solubility and compatibility in polyester molecules and suppress crystallinity effectively. HPN improves the hydrolytical resistance of polyester molecules, particularly in waterborne coating voir moins | |
| Imidazole | BASF SE, Intermediates Division | Imidazole is a catalyst for epoxy reactions, blocking agent for polyisocyanates. Imidazole is used as catalyst for the modification of epoxy resins and for two components epoxy systems. It is suitable as a blocking agent for polyisocyanates in powder coa...voir plus Imidazole is a catalyst for epoxy reactions, blocking agent for polyisocyanates. Imidazole is used as catalyst for the modification of epoxy resins and for two components epoxy systems. It is suitable as a blocking agent for polyisocyanates in powder coatings. voir moins | |
| Iso-Butyl vinyl ether, IBVE | BASF SE, Intermediates Division | Iso-Butyl vinyl ether, IBVE is a monomer for copolymers with vinyl chlorides (Laroflex®) or TFCE 1,1,2-trifluoro-2-chloroethene. Vinyl ethers form alternating copolymers via charge transfer-complex polymerization with electron-deficient monomers, such as...voir plus Iso-Butyl vinyl ether, IBVE is a monomer for copolymers with vinyl chlorides (Laroflex®) or TFCE 1,1,2-trifluoro-2-chloroethene. Vinyl ethers form alternating copolymers via charge transfer-complex polymerization with electron-deficient monomers, such as vinyl chlorides, maleic anhydride, TFCE, resulting in better solubility and flexibility. voir moins | |
| Isophorone diamine | BASF SE, Intermediates Division | Isophorone diamine is a cross linker for epoxy resins, building block for polyamides. Isophorone diamine is used in epoxy coatings, epoxy adhesives and epoxy composites. Isophorone diamine improves the hydrophobicity of epoxy resins with less sensitivit...voir plus Isophorone diamine is a cross linker for epoxy resins, building block for polyamides. Isophorone diamine is used in epoxy coatings, epoxy adhesives and epoxy composites. Isophorone diamine improves the hydrophobicity of epoxy resins with less sensitivity against humidity while film formation. voir moins | |
| KTR-100 | Suparna Chemicals Ltd. | KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-100 has a softening point of 95 to 105 °C, in butyl acetate of 75 to 95 at 25 °C (cps), and a hydroxyl value of 170 to 200. voir moins | |
| KTR-118 | Suparna Chemicals Ltd. | KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-118 has a softening point of 105 to 115 °C, in butyl acetate of 100 to 120 at 25 °C (cps), and a hydroxyl value of 180 to 210. voir moins | |
| KTR-123 | Suparna Chemicals Ltd. | KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-123 has a softening point of 105 to 115 °C, in butyl acetate of 110 to 140 at 25 °C (cps), and a hydroxyl value of 200 to 230. voir moins | |
| Liquid NVC | BASF SE, Intermediates Division | Liquid NVC is a reactive diluent for radiation curing coating and inks. It is liquid at room temperature, has high cure speed, excellent viscosity reduction, excellent substrate wetting, and improves adhesion. | |
| LX®-1035 Resin | Neville Chemical Company | LX®-1035 Resin is a flaked resin that improves cohesive strength and promotes heat resistance of adhesives. In addition it can contribute to rapid solvent release and faster drying of litho inks. It has applications in the adhesives and sealants industry ...voir plus LX®-1035 Resin is a flaked resin that improves cohesive strength and promotes heat resistance of adhesives. In addition it can contribute to rapid solvent release and faster drying of litho inks. It has applications in the adhesives and sealants industry as well as in certain coatings related to the automobile industry. voir moins | |
| LX®-1200 | Neville Chemical Company | LX®-1200 is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, improves tack and bond strength in adhesives and enhances leafing and brilliance in metallic paints and inks. It is applied to mastics, constructi...voir plus LX®-1200 is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, improves tack and bond strength in adhesives and enhances leafing and brilliance in metallic paints and inks. It is applied to mastics, construction and flooring adhesives, high solids solvent-borne alkyd based coatings, litho printing inks and aluminum paint. voir moins | |
| LX®-1200, 130 | Neville Chemical Company | LX®-1200, 130 is an inert thermoplastic hydrocarbon resin flake. This product is applied to mastics, construction and flooring adhesives, high solids solvent-borne alkyd based coatings, litho printing inks, metallic litho printing inks and aluminum paint. | |
| LX®-2161 Resin | Neville Chemical Company | LX®-2161 Resin is an inert thermoplastic hydrocarbon resin of amber flakes that enhances the wetting of pigments and fillers, improves tack and bond strength in adhesives and are soluble in aliphatic solvents and vegetable oils. They can be applied to lit...voir plus LX®-2161 Resin is an inert thermoplastic hydrocarbon resin of amber flakes that enhances the wetting of pigments and fillers, improves tack and bond strength in adhesives and are soluble in aliphatic solvents and vegetable oils. They can be applied to litho printing inks and high solids solvent-borne alkyd based coatings in addition to mastics, construction and flooring adhesives. voir moins |
