| EXOCOAT™ AM | Axcentive Sarl | EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down v...voir plus EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down viruses and bacteria. It eradicates viruses such as influenza, SARS-COV-2, dengue & hepatitis and bacteria such as E. coli, MSRA, streptococcus, listeria, pneumonia, and salmonella. It is activated by light and displays quick drying at room temperature. Spray application is recommended to reach thin monolayers. It exhibits curing at room temperature up to 300°C and super hard particles (1GPa Vickers). It is easy to apply & durable, allowing longer disinfection intervals while preserving hygiene level. It shows non-silver leaching, efficacious even under low light conditions, lower service frequency, and no need for frequent disinfection routine. It is used in the state-of-the-art continuous antimicrobial coating for high-traffic areas. EXOCOAT® AM is suitable for topcoats for any surface inside buildings, stores, hospitals, and vehicles. The shelf life of this product is 9 months. voir moins | |
| FIPOLDER™ FHP05040 | Polygroup Inc. | FIPOLDER™ FHP05040 is a high density polyethylene (HDPE) polymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. FIPOLDER™ materials are pure polyethylene with broad regulatory compliance and con...voir plus FIPOLDER™ FHP05040 is a high density polyethylene (HDPE) polymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. FIPOLDER™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. voir moins | |
| FIPOLDER™ FHP05080 | Polygroup Inc. | FIPOLDER™ FHP05080 is a high density polyethylene (HDPE) polymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. FIPOLDER™ materials are pure polyethylene with broad regulatory compliance and con...voir plus FIPOLDER™ FHP05080 is a high density polyethylene (HDPE) polymer in fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. FIPOLDER™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. voir moins | |
| FIPOLDER™ HM300 | Polygroup Inc. | FIPOLDER™ HM300 is a high density polyethylene (HDPE) Polymer in a medium-fine particle powder form. Its minerals are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some applicatio...voir plus FIPOLDER™ HM300 is a high density polyethylene (HDPE) Polymer in a medium-fine particle powder form. Its minerals are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. FIPOLDER™ powders are well suited for a variety of applications including for use in structural paints and coatings, textiles, soap and cleaners, Etc.. voir moins | |
| HP series™ HM080 | Polygroup Inc. | HP series™ HM080 is a hot-melt adhesive HDPE powder for interlining purposes. It has a high melting point which contributes to its heat resistance. HP series™ HM080 is designed by a special method of TWO H Chem's own technology to meet the requirements fo...voir plus HP series™ HM080 is a hot-melt adhesive HDPE powder for interlining purposes. It has a high melting point which contributes to its heat resistance. HP series™ HM080 is designed by a special method of TWO H Chem's own technology to meet the requirements for coating modern textile interlinings and is well suited for paste coatings. voir moins | |
| HP series™ HM200 | Polygroup Inc. | HP series™ HM200 is a hot-melt adhesive HDPE powder for interlining purposes. It has a high melting point which contributes to its heat resistance. HP series™ HM080 is designed by a special method of TWO H Chem's own technology to meet the requirements fo...voir plus HP series™ HM200 is a hot-melt adhesive HDPE powder for interlining purposes. It has a high melting point which contributes to its heat resistance. HP series™ HM080 is designed by a special method of TWO H Chem's own technology to meet the requirements for coating modern textile interlinings and is well suited for paste coatings. voir moins | |
| Ketjenflex® 12 | Axcentive Sarl | Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl com...voir plus Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl compounds, and PVC based plastisols. It can also be used in PVC based polymers, nitrocellulose resins, and cyanoacrylate adhesives. voir moins | |
| Ketjenflex® 6 | Axcentive Sarl | Ketjenflex® 6 is a toluene sulfonamide in the form of a white crystalline powder. It is used as a plasticizer in inks, adhesives, and coatings. Ketjenflex® 6 can be used with resins such as nitrocellulose, polyamide, PVAC, rosin, epoxy, and more. | |
| Ketjenflex® 8 | Axcentive Sarl | Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coa...voir plus Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coatings, synthetic polyamides, epoxy coatings and adhesives, and more. voir moins | |
| Ketjenflex® 9S | Axcentive Sarl | Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wo...voir plus Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wood adhesives, epoxy and polyurethane coatings and adhesives, and other applications. voir moins | |
| Ketjenflex® CP | Axcentive Sarl | Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings. | |
| Ketjenflex® MH | Axcentive Sarl | Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printi...voir plus Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printing inks. voir moins | |
| Ketjenflex® MS 80 | Axcentive Sarl | Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured in...voir plus Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured into desired formulations. It has applications in nitrocellulose coatings, cellulose acetate formulations, and printing inks. voir moins | |
| KTR-100 | Suparna Chemicals Ltd. | KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-100 has a softening point of 95 to 105 °C, in butyl acetate of 75 to 95 at 25 °C (cps), and a hydroxyl value of 170 to 200. voir moins | |
| KTR-118 | Suparna Chemicals Ltd. | KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-118 has a softening point of 105 to 115 °C, in butyl acetate of 100 to 120 at 25 °C (cps), and a hydroxyl value of 180 to 210. voir moins | |
| KTR-123 | Suparna Chemicals Ltd. | KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-123 has a softening point of 105 to 115 °C, in butyl acetate of 110 to 140 at 25 °C (cps), and a hydroxyl value of 200 to 230. voir moins | |
| NOVACOM-P™ HFS2100P | Polygroup Inc. | NOVACOM-P™ HFS2100P is a maleic anhydride (MAH) grafted high density polyethylene (HPDE) polymer in a powder form. These polar materials have been specifically designed to provide adhesion to inorganic fillers or additives, wood and paper fiber, glass, EV...voir plus NOVACOM-P™ HFS2100P is a maleic anhydride (MAH) grafted high density polyethylene (HPDE) polymer in a powder form. These polar materials have been specifically designed to provide adhesion to inorganic fillers or additives, wood and paper fiber, glass, EVOH, Nylon and other materials. Primarily markets for these materials are plastics compounding and mixed plastic recycle industries as compatibilizer. voir moins | |
| PROPOLDER™ MPP2010 | Polygroup Inc. | PROPOLDER™ MPP2010 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with graft...voir plus PROPOLDER™ MPP2010 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with grafted polar groups for enhanced performance in specialty applications such as paints and coatings, cosmetics, personal care and textiles. voir moins | |
| PROPOLDER™ MPP2020 | Polygroup Inc. | PROPOLDER™ MPP2020 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with graft...voir plus PROPOLDER™ MPP2020 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with grafted polar groups for enhanced performance in specialty applications such as paints and coatings, cosmetics, personal care and textiles. voir moins | |
| PROPOLDER™ MPP2040 | Polygroup Inc. | PROPOLDER™ MPP2040 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with graft...voir plus PROPOLDER™ MPP2040 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with grafted polar groups for enhanced performance in specialty applications such as paints and coatings, cosmetics, personal care and textiles. voir moins | |
| PROPOLDER™ MPP2060 | Polygroup Inc. | PROPOLDER™ MPP2060 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with graft...voir plus PROPOLDER™ MPP2060 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with grafted polar groups for enhanced performance in specialty applications such as paints and coatings, cosmetics, personal care and textiles. voir moins | |
| PROPOLDER™ MPP2080 | Polygroup Inc. | PROPOLDER™ MPP2080 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with graft...voir plus PROPOLDER™ MPP2080 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with grafted polar groups for enhanced performance in specialty applications such as paints and coatings, cosmetics, personal care and textiles. voir moins | |
| PROPOLDER™ MPP2100 | Polygroup Inc. | PROPOLDER™ MPP2100 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with graft...voir plus PROPOLDER™ MPP2100 is a maleic anhydride modified polypropylene (PP) polymer in a fine particle powder form. Unlike waxes, these higher molecular weight materials exhibit high toughness. PROPOLDER™ MPP series materials are polypropylene powders with grafted polar groups for enhanced performance in specialty applications such as paints and coatings, cosmetics, personal care and textiles. voir moins | |
| SP Series™ SHP1500-1 | Polygroup Inc. | SP Series™ SHP1500-1 is a high molecular weight, high density, polyethylene (HMWHDPE) polymer in a fine particle powder form. These unique materials exhibit very high toughness. The SP Series™ materials are pure polyethylene with broad regulatory complian...voir plus SP Series™ SHP1500-1 is a high molecular weight, high density, polyethylene (HMWHDPE) polymer in a fine particle powder form. These unique materials exhibit very high toughness. The SP Series™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. These powders are well suited for use in structural paints and coating applications that require anti-slip, structural, or satin and matt finish effects. voir moins | |
| SP Series™ SHP4080-1 | Polygroup Inc. | SP Series™ SHP4080-1 is a high molecular weight, high density, polyethylene (HMWHDPE) polymer in a fine particle powder form. These unique materials exhibit very high toughness. The SP Series™ materials are pure polyethylene with broad regulatory complian...voir plus SP Series™ SHP4080-1 is a high molecular weight, high density, polyethylene (HMWHDPE) polymer in a fine particle powder form. These unique materials exhibit very high toughness. The SP Series™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. These powders are well suited for use in structural paints and coating applications that require anti-slip, structural, or satin and matt finish effects. voir moins | |
| SP Series™ SHP8015-1 | Polygroup Inc. | SP Series™ SHP8015-1 is a high molecular weight, high density, polyethylene (HMWHDPE) polymer in a fine particle powder form. These unique materials exhibit very high toughness. The SP Series™ materials are pure polyethylene with broad regulatory complian...voir plus SP Series™ SHP8015-1 is a high molecular weight, high density, polyethylene (HMWHDPE) polymer in a fine particle powder form. These unique materials exhibit very high toughness. The SP Series™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. These powders are well suited for use in structural paints and coating applications that require anti-slip, structural, or satin and matt finish effects. voir moins | |
| Automated Discharge Systems | Charles Ross & Son Company | A Ross Discharge System can eliminate wasted hours scraping heavy or sticky materials from a mix vessel. With push-button simplicity, the system can automatically discharge a 1000-gallon batch in minutes — into bulk containers, filling or packaging equipm...voir plus A Ross Discharge System can eliminate wasted hours scraping heavy or sticky materials from a mix vessel. With push-button simplicity, the system can automatically discharge a 1000-gallon batch in minutes — into bulk containers, filling or packaging equipment, an extruder, or a two or three-roll mill. voir moins |  |
| Double Planetary Mixer | Charles Ross & Son Company | Ross pioneered the Double Planetary Mixer design more than 60 years ago. Design updates make this mixer suitable for use in applications up to 7,000,000 centipoise. A high speed design variation is also available. |  |
| High Shear Mixer | Charles Ross & Son Company | All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear...voir plus All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear particles and droplets, and expel material at high velocity into the surrounding mix, creating intense hydraulic shear. voir moins |  |
| High Speed Disperser | Charles Ross & Son Company | Ross High Speed Dispersers are the industry standard for durability, faster dispersion and low maintenance costs. Standard models include: explosion-proof, inverter duty motors; heavy duty V-belt drives and bearings; safety switches; an air/oil hydraulic ...voir plus Ross High Speed Dispersers are the industry standard for durability, faster dispersion and low maintenance costs. Standard models include: explosion-proof, inverter duty motors; heavy duty V-belt drives and bearings; safety switches; an air/oil hydraulic lift system with hand/foot controls; and stainless steel wetted parts and shaft guard. Sizes range from 1/2 HP to 200 HP to handle batches from 1 to 2000 gallons. Custom designs are also available. voir moins |  |
| Multi-Shaft Mixer | Charles Ross & Son Company | We offer Dual and Triple Shaft designs to meet your specific process requirements. Our economical Dual Shaft design includes a conventional high speed disperser and a two wing anchor agitator. This configuration is ideal for straight forward dispersion an...voir plus We offer Dual and Triple Shaft designs to meet your specific process requirements. Our economical Dual Shaft design includes a conventional high speed disperser and a two wing anchor agitator. This configuration is ideal for straight forward dispersion and mixing applications. voir moins |  |
| Planetary Dispersers | Charles Ross & Son Company | The patented Planetary Disperser combines a planetary blade and a high speed dispersion blade. The planetary and the high speed disperser blades rotate on their own axes and also rotate continuously around the vessel. The planetary blade feeds materials ...voir plus The patented Planetary Disperser combines a planetary blade and a high speed dispersion blade. The planetary and the high speed disperser blades rotate on their own axes and also rotate continuously around the vessel. The planetary blade feeds materials directly into the high shear zone of the orbiting high speed disperser. This combination of unique mixing actions eliminate the need for multiple mixers i.e. 2 technologies in one machine. voir moins |  |
| Powder Induction | Charles Ross & Son Company | All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear...voir plus All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear particles and droplets, and expel material at high velocity into the surrounding mix, creating intense hydraulic shear. voir moins |  |
| PreMax | Charles Ross & Son Company | This single-stage rotor/stator generator is specially contoured to generate both high shear and vigorous flow in a batch mixing environment. Designed especially for pigment dispersions, the Delta rotor/stator generator is used in the Ross PreMax* to produ...voir plus This single-stage rotor/stator generator is specially contoured to generate both high shear and vigorous flow in a batch mixing environment. Designed especially for pigment dispersions, the Delta rotor/stator generator is used in the Ross PreMax* to produce an intense combination of mechanical, hydraulic and cavitational shear, which results in aggressive deagglomeration. voir moins |  |
| Ribbon Blender | Charles Ross & Son Company | Ribbon Blenders are ideal for powder blending applications. The dual action ribbon agitator creates an intimate blend in a short cycle time. Ross stocks Ribbon Blenders in many sizes from 1 - 100 cu.ft. working capacity. |  |
| Sanitary Mixers | Charles Ross & Son Company | Ross serves the requirements of the Food, Cosmetic and Pharmaceutical industries, in virtually every industrialized country around the world. We have the experience and production capacity that no other manufacturer of specialty mixing and blending equipm...voir plus Ross serves the requirements of the Food, Cosmetic and Pharmaceutical industries, in virtually every industrialized country around the world. We have the experience and production capacity that no other manufacturer of specialty mixing and blending equipment can match. voir moins |  |
| Static/Motionless Mixers | Charles Ross & Son Company | Ross LPD/LLPD (low pressure drop) and ISG (interfacial surface generator) Motionless Mixers are well known for their wide ranging uses in turbulent and laminar flow mixing applications. |  |
| Systems And Controls | Charles Ross & Son Company | Ross Systems and Controls (SysCon) is a leading worldwide supplier of control systems. We offer packages that range from simple on/off switches to sophisticated PLC based recipe systems. Each system, standard or custom, is designed to meet your specific n...voir plus Ross Systems and Controls (SysCon) is a leading worldwide supplier of control systems. We offer packages that range from simple on/off switches to sophisticated PLC based recipe systems. Each system, standard or custom, is designed to meet your specific needs. voir moins |  |
| Three Roll Mill | Charles Ross & Son Company | When Ross produced the first Three Roll Mill more than 80 years ago, we revolutionized pigment dispersion — with superior consistency and finer dispersion than ever before. Today the original Ross Three Roll Mills are still the standard by which all other...voir plus When Ross produced the first Three Roll Mill more than 80 years ago, we revolutionized pigment dispersion — with superior consistency and finer dispersion than ever before. Today the original Ross Three Roll Mills are still the standard by which all others are measured — in applications as diverse as magnetic coatings, cosmetics, paints, inks and high performance ceramics. voir moins |  |
| Tumble Blenders | Charles Ross & Son Company | Ross Tumble Blenders are supplied with generous standard features, including double cone design in 316 stainless steel construction, manually operated Butterfly valve for discharge - 24” discharge clearance Hinged stainless steel charging opening, mirror ...voir plus Ross Tumble Blenders are supplied with generous standard features, including double cone design in 316 stainless steel construction, manually operated Butterfly valve for discharge - 24” discharge clearance Hinged stainless steel charging opening, mirror finish on interior surfaces, 150 grit finish on exterior surfaces, and the non-stainless steel components are finished with a durable two-component paint. voir moins |  |
| Vertical Blender | Charles Ross & Son Company | Ross Vertical Blenders provide an excellent design alternative for applications when your product is shear sensitive or your process parameters are critical Products that require low-impact blending are best handled in a Ross Vertical Blender. The blendin...voir plus Ross Vertical Blenders provide an excellent design alternative for applications when your product is shear sensitive or your process parameters are critical Products that require low-impact blending are best handled in a Ross Vertical Blender. The blending action of the slow-turning blending screw is far more gentle than the agitators in a Ribbon Blender of the same working volume. voir moins |  |
