| 3M™ Ceramic Microspheres W-210 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M c...voir plus 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-210 are typically chosen over other 3M ceramic microspheres for higher gloss formulations. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. voir moins | |
| 3M™ Ceramic Microspheres W-410 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler load...voir plus 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-410 are typically chosen over other 3M ceramic microspheres for their overall balance in properties. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. voir moins | |
| 3M™ Ceramic Microspheres W-610 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic m...voir plus 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-610 are typically chosen over other 3M ceramic microspheres for increased durability. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. voir moins | |
| 3M™ Fluorosurfactant FC-4430 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...voir plus 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4430 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product can provide stain and dirt pick up resistance. voir moins | |
| 3M™ Fluorosurfactant FC-4432 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...voir plus 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4432 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. voir moins | |
| 3M™ Fluorosurfactant FC-4434 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...voir plus 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4434 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. voir moins | |
| 3M™ Glass Bubbles iM16K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...voir plus 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles iM30K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...voir plus 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K1 | 3M Advanced Materials Division | 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...voir plus 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K15 | 3M Advanced Materials Division | 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K20 | 3M Advanced Materials Division | 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K25 | 3M Advanced Materials Division | 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K37 | 3M Advanced Materials Division | 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...voir plus 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K42HS | 3M Advanced Materials Division | 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...voir plus 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K46 | 3M Advanced Materials Division | 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S15 | 3M Advanced Materials Division | 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S22 | 3M Advanced Materials Division | 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...voir plus 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S28HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...voir plus 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S32 | 3M Advanced Materials Division | 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S35 | 3M Advanced Materials Division | 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S38 | 3M Advanced Materials Division | 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S38HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush streng...voir plus 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S42XHS | 3M Advanced Materials Division | 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...voir plus 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S60 | 3M Advanced Materials Division | 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...voir plus 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S60HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...voir plus 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles XLD3000 | 3M Advanced Materials Division | 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush str...voir plus 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-250 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product pe...voir plus 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-250 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-250 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-270 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The ...voir plus 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-270 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-270 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-450 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the...voir plus 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-450 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-450 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-451 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates th...voir plus 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-451 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-451 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. voir moins | |
| 3M™ Stain Resistant Additive SRC-220 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product...voir plus 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRC-220 offers durability, long-lasting performance and UV resistance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRC-220 is easy to incorporate into existing water and some solvent-based products and can be added to existing formulations or diluted with water or water miscible solvents and used as a stand-alone sealer. voir moins | |
| Easy Clean Coatings 1000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time...voir plus 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. voir moins | |
| Easy Clean Coatings 4000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-4000 is a fluoropolymer used for coating ceramic and glass surfaces. Once it air-dries, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. | |
| Easy Clean Coatings 6000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, he...voir plus 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. voir moins | |
| STANLUX® Gold 12000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 12000 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 1...voir plus STANLUX® Gold 12000 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 12000 is available in several shades and has an average size of 16 microns. voir moins | |
| STANLUX® Gold 13000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 13000 is a fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for use in flexographic and gravure systems. STANLUX® Gold 13...voir plus STANLUX® Gold 13000 is a fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for use in flexographic and gravure systems. STANLUX® Gold 13000 is available in several shades and has an average size of 16 microns. voir moins | |
| STANLUX® Gold 13300 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 13300 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 1...voir plus STANLUX® Gold 13300 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 13300 is available in several shades and has an average size of 12 microns. voir moins | |
| STANLUX® Gold 14000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 14000 is super fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment generates decorative metallic effects and is used in offset printing inks. STANLUX® Gold 14000 i...voir plus STANLUX® Gold 14000 is super fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment generates decorative metallic effects and is used in offset printing inks. STANLUX® Gold 14000 is available in several shades and has an average size of 5 microns. voir moins | |
| STANLUX® Gold 2000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2000 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...voir plus STANLUX® Gold 2000 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2000 is available in several shades and has an average size of 50 microns. voir moins | |
| STANLUX® Gold 2100 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2100 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...voir plus STANLUX® Gold 2100 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2100 is available in several shades and has an average size of 50 microns. voir moins | |
| STANLUX® Gold 2700 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2700 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...voir plus STANLUX® Gold 2700 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2700 is available in several shades and has an average size of 45 microns. voir moins | |
| STANLUX® Gold 2800 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2800 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...voir plus STANLUX® Gold 2800 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2800 is available in several shades and has an average size of 45 microns. voir moins | |
| STANLUX® Gold 3500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 3500 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...voir plus STANLUX® Gold 3500 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 3500 is available in several shades and has an average size of 35 microns. voir moins | |
| STANLUX® Gold 3600 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 3600 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...voir plus STANLUX® Gold 3600 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 3600 is available in several shades and has an average size of 35 microns. voir moins | |
| STANLUX® Gold 4500 (Shade C) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4500 has an average size of 25 microns and a 1.5% water retention rate with 3.4 - 4.2 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 4500 (Shade D) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints, and silk screen inks, and it is rec...voir plus STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints, and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4500 has an average size of 30 microns and a 8% water retention rate with a 3.4 - 4.2 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 4500 (Shades P - RP - R) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4500 has an average size of 25 microns and a 1.5% water retention rate with 4.3-5.4 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 4600 (Shade C) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4600 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 4600 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4600 has an average size of 30 microns and a 1.5% water retention rate with a 3.4 - 4.2 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 4600 (Shades P - RP - R) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4600 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 4600 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4600 has an average size of 30 microns and a 1.5% water retention rate with a 4.3 - 5.4 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 5500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 5500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 5500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where regular surface finish and hiding power are required. STANLUX® Gold 5500 is available in several shades and has an average size of 23 microns. It possesses a 0.5% water retention rate with a 4.2 - 6.0 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 6500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 6500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 6500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where regular surface finish and hiding power are required. STANLUX® Gold 6500 is available in several shades and has an average size of 20 microns. It possesses a 5% water retention rate with a 5.5 - 6.5 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Gold 7500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 7500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...voir plus STANLUX® Gold 7500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where regular surface finish and hiding power are required. STANLUX® Gold 7500 is available in several shades and has an average size of 18 microns. It possesses a 0.8% water retention rate with a 6.3 - 7.5 (cm²/g Min) water coverage property. voir moins | |
| STANLUX® Hydro 140 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Hydro 140 is a stabilized aluminium leafing paste with medium-coarse lamellar particles, recommended for use in waterborne paints. This product has a maximum retention of 1% in # 325 mesh. | |
| STANLUX® Hydro 150 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Hydro 150 is a stabilized aluminium leafing paste with medium-coarse lamellar particles, recommended for use in waterborne paints. This product has a maximum retention of 4% in # 325 mesh. | |
| STANLUX® Paste 100 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 100 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product creates a unique shiny aesthetic effect that provides the applied system with a protective barrier, coverage, corrosion resistance, and ...voir plus STANLUX® Paste 100 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product creates a unique shiny aesthetic effect that provides the applied system with a protective barrier, coverage, corrosion resistance, and thermal reflection. STANLUX® Paste 100 is specially recommended for formulation systems with low tolerance to aliphatic solvent and is commonly used for maintenance and general industrial paints. voir moins | |
| STANLUX® Paste 100N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 100N is a non-leafing type aluminum paste made of lamellar particles covered with stearic acid. This product creates a unique shiny aesthetic effect that provides the applied system with a protective barrier, coverage, corrosion resistance,...voir plus STANLUX® Paste 100N is a non-leafing type aluminum paste made of lamellar particles covered with stearic acid. This product creates a unique shiny aesthetic effect that provides the applied system with a protective barrier, coverage, corrosion resistance, and thermal reflection. STANLUX® Paste 100N is specially recommended for formulation systems with low tolerance to aliphatic solvent and is commonly used for maintenance, protective, or marine coatings. voir moins | |
| STANLUX® Paste 1100 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1100 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1100 is specially recommended for formulation...voir plus STANLUX® Paste 1100 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1100 is specially recommended for formulation systems with low tolerance to aliphatic solvent and is commonly used for maintenance, protective and marine coatings, and roof coatings. It has an average particle size of 18 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) voir moins | |
| STANLUX® Paste 1100N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1100N is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1100N is specially recommended for formulatio...voir plus STANLUX® Paste 1100N is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1100N is specially recommended for formulation systems with low tolerance to aliphatic solvent and is commonly used for maintenance, protective and marine coatings, and roof coatings. It has an average particle size of 18 microns and uses High Aromatic solvent. voir moins | |
| STANLUX® Paste 1120 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1120 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1120 is specially recommended for formulation ...voir plus STANLUX® Paste 1120 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1120 is specially recommended for formulation systems with low tolerance to aliphatic solvent and is commonly used for maintenance, protective and marine coatings, and roof coatings. It has an average particle size of 17 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) voir moins | |
| STANLUX® Paste 1130 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1130 is a non-leafing type aluminum paste made of fine lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1130 is specially recommended for use in ...voir plus STANLUX® Paste 1130 is a non-leafing type aluminum paste made of fine lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1130 is specially recommended for use in decorative paints, industrial paints, maintenance, protective and marine coatings, and trade paints. It has an average particle size of 11 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) voir moins | |
| STANLUX® Paste 120 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 120 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 120 commonly used for general industrial...voir plus STANLUX® Paste 120 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 120 commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 17 microns and a minimum water coverage of 20,000 cm2/g. voir moins | |
| STANLUX® Paste 1200 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1200 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1200 has a high degree of hiding power and is ...voir plus STANLUX® Paste 1200 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1200 has a high degree of hiding power and is recommended for use in internal can coatings. It has an average particle size of 14 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) voir moins | |
| STANLUX® Paste 1290 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1290 is a non-leafing type aluminum paste made of fine lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1290 has a high degree of hiding power an...voir plus STANLUX® Paste 1290 is a non-leafing type aluminum paste made of fine lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1290 has a high degree of hiding power and is recommended for use in internal can coatings. It has an average particle size of 8 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) voir moins | |
| STANLUX® Paste 130 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 130 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 130 commonly used for general industrial ...voir plus STANLUX® Paste 130 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 130 commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 19 microns and a minimum water coverage of 21,000 cm2/g. voir moins | |
| STANLUX® Paste 130N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 130N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 130N is specially recommended for applic...voir plus STANLUX® Paste 130N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 130N is specially recommended for application in formulations based on resins that are incompatible with aliphatic solvents and is commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 19 microns and a minimum water coverage of 21,000 cm2/g. voir moins | |
| STANLUX® Paste 140 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 140 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 140 is recommended for application in for...voir plus STANLUX® Paste 140 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 140 is recommended for application in formulations that require aluminium pigment with high metallic effect and is commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 19 microns and a minimum water coverage of 21,000 cm2/g. voir moins | |
| STANLUX® Paste 150 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 150 is a leafing type aluminum paste made of medium-coarse lamellar particles covered with stearic acid. STANLUX® Paste 150 is recommended for application in formulations that require aluminium pigment with high metallic effect and is commo...voir plus STANLUX® Paste 150 is a leafing type aluminum paste made of medium-coarse lamellar particles covered with stearic acid. STANLUX® Paste 150 is recommended for application in formulations that require aluminium pigment with high metallic effect and is commonly used for industrial paints, and roof coatings. It has an average particle size of 19 microns and a minimum water coverage of 14,000 cm2/g. voir moins | |
| STANLUX® Paste 1600 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1600 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600 is considered to be standard level and is...voir plus STANLUX® Paste 1600 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600 is considered to be standard level and is recommended for paint formulations that require aluminium pigment with high metallic effect including: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. It has an average particle size of 23 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) voir moins | |
| STANLUX® Paste 1600N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1600N is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600N is considered to be standard level and ...voir plus STANLUX® Paste 1600N is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600N is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 23 microns and uses a HA (High Aromatic) solvent. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. voir moins | |
| STANLUX® Paste 166 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 166 is a leafing type aluminum paste made of medium size lamellar particles covered with stearic acid. STANLUX® Paste 166 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paint...voir plus STANLUX® Paste 166 is a leafing type aluminum paste made of medium size lamellar particles covered with stearic acid. STANLUX® Paste 166 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paints, industrial paints, and trade paints. It has an average particle size of 15 microns and a minimum water coverage of 22,000cm2/g. voir moins | |
| STANLUX® Paste 1700 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1700 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1700 is considered to be standard level and is...voir plus STANLUX® Paste 1700 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1700 is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 21 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. voir moins | |
| STANLUX® Paste 1770 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1770 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770 is considered to be standard level...voir plus STANLUX® Paste 1770 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770 is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 16 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. voir moins | |
| STANLUX® Paste 1770/60 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1770/60 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770/60 is considered to be standard...voir plus STANLUX® Paste 1770/60 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770/60 is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 16 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. STANLUX® Paste 1770/60 has the same characteristics of Stanlux Paste 1770 with 60% of solids. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. voir moins | |
| STANLUX® Paste 1870 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1870 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1870 is considered to be standard level...voir plus STANLUX® Paste 1870 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1870 is considered to be standard level and is recommended for systems requiring differentiated metallic finishes, brighter color, and high hiding power. It has an average particle size of 16 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: aerosol spray decorative paints, industrial paints, and trade paints. voir moins | |
| STANLUX® Paste 1900 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1900 is a non-leafing type aluminum paste made of coarse lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1900 is considered to be standard level...voir plus STANLUX® Paste 1900 is a non-leafing type aluminum paste made of coarse lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1900 is considered to be standard level and is recommended for systems requiring protective properties. It has an average particle size of 32 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: industrial paints, maintenance, protective and marine coatings. voir moins | |
| STANLUX® Paste 200 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 200 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paints, trade pai...voir plus STANLUX® Paste 200 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paints, trade paints, and printing inks. It has an average particle size of 14 microns and a minimum water coverage of 20,000 cm2/g. voir moins | |
| STANLUX® Paste 2000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 2000 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 2000 is considered to be standard level...voir plus STANLUX® Paste 2000 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 2000 is considered to be standard level and is recommended for systems requiring differentiated metallic effects, and brighter metallic pigment. It has an average particle size of 21 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: decorative paints, industrial paints, and trade paints. voir moins | |
| STANLUX® Paste 200N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 200N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200N is recommended for application in products requiring high covering power and is commonly used for decorative paints, trade paint...voir plus STANLUX® Paste 200N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200N is recommended for application in products requiring high covering power and is commonly used for decorative paints, trade paints, and printing inks. It has an average particle size of 14 microns and a minimum water coverage of 20,000 cm2/g. voir moins | |
| STANLUX® Paste 260 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 260 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 260 is specially recommended for printing inks and is commonly used for aerosol spray decorative paints, flexographic printing in...voir plus STANLUX® Paste 260 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 260 is specially recommended for printing inks and is commonly used for aerosol spray decorative paints, flexographic printing inks, and gravure printing inks. It has an average particle size of 14 microns and a minimum water coverage of 28,000 cm2/g. voir moins | |
| STANLUX® Paste 266 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 266 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 266 is specially recommended for high grade and brilliant printing inks and is commonly used for aerosol spray decorative paints,...voir plus STANLUX® Paste 266 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 266 is specially recommended for high grade and brilliant printing inks and is commonly used for aerosol spray decorative paints, flexographic and gravure printing inks that require aluminium pigment with a high metallic effect. It has an average particle size of 14 microns and a minimum water coverage of 28,000 cm2/g. voir moins | |
| STANLUX® Paste 270/70 IPA | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 270/70 IPA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 270/70 IPA is specially recomme...voir plus STANLUX® Paste 270/70 IPA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 270/70 IPA is specially recommended for printing inks and is commonly used for flexography and gravure free of residual solvent odour. It has an average particle size of 11 microns and a minimum water coverage of 30,000 cm2/g. voir moins | |
| STANLUX® Paste 280 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 280 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 280 is specially recommended for high grade printing inks and is commonly used for aerosol spray decorative paints, flexographic ...voir plus STANLUX® Paste 280 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 280 is specially recommended for high grade printing inks and is commonly used for aerosol spray decorative paints, flexographic and gravure printing inks that require aluminium pigment with a high metallic effect. It has an average particle size of 12 microns and a minimum water coverage of 34,000 cm2/g. voir moins | |
| STANLUX® Paste 290 60EA | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 290 60EA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 290 60EA is specially recommended f...voir plus STANLUX® Paste 290 60EA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 290 60EA is specially recommended for printing inks and is commonly used for flexography and gravure free of residual solvent odour. It has an average particle size of 9 microns and a minimum water coverage of 45,000 cm2/g. voir moins | |
| STANLUX® Paste 290 60MO | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 290 60MO is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is formulated for high-grade offset printing inks. STANLUX® Paste 290 60MO is specially recommended for printing inks and is commonly u...voir plus STANLUX® Paste 290 60MO is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is formulated for high-grade offset printing inks. STANLUX® Paste 290 60MO is specially recommended for printing inks and is commonly used for offset printing ink free of residual solvent odour. It has an average particle size of 9 microns and a minimum water coverage of 45,000 cm2/g. voir moins | |
| STANLUX® Paste 340 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 340 is a leafing type aluminum paste made of coarse lamellar particles covered with stearic acid that provide a reflection effect or barrier protection. STANLUX® Paste 340 is specially recommended for printing inks and is commonly used for ...voir plus STANLUX® Paste 340 is a leafing type aluminum paste made of coarse lamellar particles covered with stearic acid that provide a reflection effect or barrier protection. STANLUX® Paste 340 is specially recommended for printing inks and is commonly used for maintenance, protective and marine coatings, and roof coatings. It has an average particle size of 21 microns and a minimum water coverage of 9,000 cm2/g. voir moins | |
| STANLUX® Paste 340N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 340N is a leafing type aluminum paste made of coarse lamellar particles covered with stearic acid that provide a reflective effect. STANLUX® Paste 340N is specially recommended for application in formulations based on resins that are incomp...voir plus STANLUX® Paste 340N is a leafing type aluminum paste made of coarse lamellar particles covered with stearic acid that provide a reflective effect. STANLUX® Paste 340N is specially recommended for application in formulations based on resins that are incompatible with aliphatic solvents and is commonly used for maintenance, protective, marine, and roof coatings. It has an average particle size of 21 microns and a minimum water coverage of 9,000 cm2/g. voir moins | |
| STANLUX® Pell Gold 130 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Pell Gold 130 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to appl...voir plus STANLUX® Pell Gold 130 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to applied systems. STANLUX® Pell Gold 130 is available is several shades and is recommended for use in flexographic and gravure printing inks. voir moins | |
| STANLUX® Pell Gold 131 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Pell Gold 131 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to appl...voir plus STANLUX® Pell Gold 131 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to applied systems. STANLUX® Pell Gold 130 is recommended for use in flexographic and gravure printing inks. voir moins | |
| STANLUX® Silver 2210 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 2210 is a non-leafing type aluminium pigment with coarse lamellar particles that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 2210 has an a...voir plus STANLUX® Silver 2210 is a non-leafing type aluminium pigment with coarse lamellar particles that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 2210 has an average particle size of 60 microns and can be used in auto parts paints, automotive paints (original and refinish), and plastic coatings. voir moins | |
| STANLUX® Silver 2240 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 2240 is a non-leafing type aluminium pigment with coarse lamellar particles that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 2240 has an a...voir plus STANLUX® Silver 2240 is a non-leafing type aluminium pigment with coarse lamellar particles that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 2240 has an average particle size of 40 microns and can be used in auto parts paints, automotive paints (original and refinish), and plastic coatings. voir moins | |
| STANLUX® Silver 3201 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3201 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX®...voir plus STANLUX® Silver 3201 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3201 has an average particle size of 29 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. voir moins | |
| STANLUX® Silver 3301 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3301 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX®...voir plus STANLUX® Silver 3301 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3301 has an average particle size of 28 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. voir moins | |
| STANLUX® Silver 3501 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3501 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX®...voir plus STANLUX® Silver 3501 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3501 has an average particle size of 24 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. voir moins | |
| STANLUX® Silver 3571 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3571 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX®...voir plus STANLUX® Silver 3571 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3571 has an average particle size of 23 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. voir moins | |
| STANLUX® Silver 3701 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3701 is a non-leafing type aluminium pigment with narrowly curved lamellar particle size distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STA...voir plus STANLUX® Silver 3701 is a non-leafing type aluminium pigment with narrowly curved lamellar particle size distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3701 has an average particle size of 21 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. voir moins | |
| STANLUX® Silver 3711 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3711 is a non-leafing type aluminium pigment with narrowly curved lamellar particle size distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STA...voir plus STANLUX® Silver 3711 is a non-leafing type aluminium pigment with narrowly curved lamellar particle size distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3711 has an average particle size of 17 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. voir moins | |
| STANLUX® Silver 3871 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3871 is a non-leafing type aluminium pigment with fine, narrowly curved lamellar particle size distribution that presents a metallic effect. It is recommended in formulations that require high hiding power. STANLUX® Silver 3871 has an aver...voir plus STANLUX® Silver 3871 is a non-leafing type aluminium pigment with fine, narrowly curved lamellar particle size distribution that presents a metallic effect. It is recommended in formulations that require high hiding power. STANLUX® Silver 3871 has an average particle size of 13 microns and can be used in auto parts paints, automotive paints (original and refinish), and plastic coatings. voir moins | |
| STANLUX® Silver 3891 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3891 is a non-leafing type aluminium pigment with fine, narrowly curved lamellar particle size distribution that presents a metallic effect. It is recommended in formulations that require the highest hiding power and clear colour property....voir plus STANLUX® Silver 3891 is a non-leafing type aluminium pigment with fine, narrowly curved lamellar particle size distribution that presents a metallic effect. It is recommended in formulations that require the highest hiding power and clear colour property. STANLUX® Silver 3891 has an average particle size of 11 microns and can be used in auto parts paints, automotive paints (original and refinish), and plastic coatings. voir moins | |
| STANLUX® Silver R2970 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver R2970 is a non-leafing type aluminium pigment with coarse lamellar particles that presents a metallic effect. It is recommended in formulations for double layer systems that require aluminium pigment with high metallic effect. STANLUX® Sil...voir plus STANLUX® Silver R2970 is a non-leafing type aluminium pigment with coarse lamellar particles that presents a metallic effect. It is recommended in formulations for double layer systems that require aluminium pigment with high metallic effect. STANLUX® Silver R2970 has an average particle size of 32 microns and can be used in auto parts paints, automotive paints (original and refinish), and plastic coatings. voir moins | |
| STANLUX® Silver R3270 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver R3270 is a non-leafing type aluminium pigment with narrowly curved lamellar particle size distribution that presents a metallic effect. It is recommended in formulations that require a high metallic effect. STANLUX® Silver R3270 has an av...voir plus STANLUX® Silver R3270 is a non-leafing type aluminium pigment with narrowly curved lamellar particle size distribution that presents a metallic effect. It is recommended in formulations that require a high metallic effect. STANLUX® Silver R3270 has an average particle size of 25 microns and can be used in auto parts paints, automotive paints (original and refinish), and plastic coatings. voir moins |
