| 3M™ Ceramic Microspheres W-210 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M c...voir plus 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-210 are typically chosen over other 3M ceramic microspheres for higher gloss formulations. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. voir moins | |
| 3M™ Ceramic Microspheres W-410 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler load...voir plus 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-410 are typically chosen over other 3M ceramic microspheres for their overall balance in properties. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. voir moins | |
| 3M™ Ceramic Microspheres W-610 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic m...voir plus 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-610 are typically chosen over other 3M ceramic microspheres for increased durability. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. voir moins | |
| 3M™ Fluorosurfactant FC-4430 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...voir plus 3M™ Fluorosurfactant FC-4430 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4430 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product can provide stain and dirt pick up resistance. voir moins | |
| 3M™ Fluorosurfactant FC-4432 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...voir plus 3M™ Fluorosurfactant FC-4432 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4432 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. voir moins | |
| 3M™ Fluorosurfactant FC-4434 | 3M Advanced Materials Division | 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liqui...voir plus 3M™ Fluorosurfactant FC-4434 drastically lowers surface tension and helps coatings overcome problems caused by surface contamination. 3M fluorosurfactants concentrate at the liquid surface, lowering the surface tension of the liquid. This allows the liquid to wet and spread more evenly, and reduces the possibility of surface defects like orange peel. 3M fluorosurfactant FC-4434 also helps paints and coatings overcome surface contamination. The lower surface tension is the property that helps overcome surface contamination to help reduce or eliminate coating defects. Additionally, this product is ideal for providing stain and dirt pick up resistance. voir moins | |
| 3M™ Glass Bubbles iM16K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...voir plus 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles iM30K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...voir plus 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K1 | 3M Advanced Materials Division | 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...voir plus 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K15 | 3M Advanced Materials Division | 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K20 | 3M Advanced Materials Division | 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K25 | 3M Advanced Materials Division | 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K37 | 3M Advanced Materials Division | 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...voir plus 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K42HS | 3M Advanced Materials Division | 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...voir plus 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles K46 | 3M Advanced Materials Division | 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S15 | 3M Advanced Materials Division | 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....voir plus 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S22 | 3M Advanced Materials Division | 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...voir plus 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S28HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...voir plus 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S32 | 3M Advanced Materials Division | 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S35 | 3M Advanced Materials Division | 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S38 | 3M Advanced Materials Division | 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...voir plus 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S38HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush streng...voir plus 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S42XHS | 3M Advanced Materials Division | 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...voir plus 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S60 | 3M Advanced Materials Division | 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...voir plus 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles S60HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...voir plus 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Glass Bubbles XLD3000 | 3M Advanced Materials Division | 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush str...voir plus 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-250 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product pe...voir plus 3M™ Stain Resistant Additive and Sealer SRA-250 is an aqueous-based fluorinated acrylic polymer dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-250 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-250 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-270 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The ...voir plus 3M™ Stain Resistant Additive and Sealer SRA-270 is an aqueous-based fluorinated acrylic modified urethane dispersion which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-270 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-270 is easy to incorporate into existing water-based products and can be added to existing formulations or diluted with water and used as a stand-alone sealer. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-450 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the...voir plus 3M™ Stain Resistant Additive and Sealer SRA-450 is a solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-450 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-450 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. voir moins | |
| 3M™ Stain Resistant Additive and Sealer SRA-451 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates th...voir plus 3M™ Stain Resistant Additive and Sealer SRA-451 is an solvent-based fluorinated acrylic polymer which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRA-451 offers durability and long-lasting performance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRA-451 is easy to incorporate into existing solvent-based products and can be added to existing formulations or diluted with solvent and used as a stand-alone sealer. It can also be used as an additive for solvent-based or 100% silicone-based sealers to boost oil repellency. voir moins | |
| 3M™ Stain Resistant Additive SRC-220 | 3M Advanced Materials Division | 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product...voir plus 3M™ Stain Resistant Additive and Sealer SRC-220 is an aqueous-based fluorinated polyurethane dispersion (PUD) which provides stain repellency and stain release characteristics for porous hard surfaces such as concrete, natural stone and grout. The product penetrates the substrate pores resulting in a low surface energy that makes it easier for fluids and stains to be removed. Additionally, 3M stain resistant additive and sealer SRC-220 offers durability, long-lasting performance and UV resistance. The substrate’s natural characteristics (color, breathability) are generally unaffected by the application of this product. 3M stain resistant additive and sealer SRC-220 is easy to incorporate into existing water and some solvent-based products and can be added to existing formulations or diluted with water or water miscible solvents and used as a stand-alone sealer. voir moins | |
| Agrocer® Blue 153 Disp. | Clariant Plastics and Coatings (Dispersions) | Agrocer® Blue 153 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning o...voir plus Agrocer® Blue 153 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of production equipment. Due to its composition, Agrocer® Blue 153 disp. is highly compatible with common seed treatment pesticide formulations as well as seed coating products. All Agrocer® dispersions are manufactured without using alkyl phenol ethoxylate (APEO) and do not require any hazardous labeling. voir moins | Request Sample |
| Agrocer® Green 007 Disp. | Clariant Plastics and Coatings (Dispersions) | Agrocer® Green 007 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning ...voir plus Agrocer® Green 007 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of production equipment. Due to its composition, Agrocer® Green 007 disp. is highly compatible with common seed treatment pesticide formulations as well as seed coating products. All Agrocer® dispersions are manufactured without using alkyl phenol ethoxylate (APEO) and do not require any hazardous labeling. voir moins | Request Sample |
| Agrocer® Red 112 Disp. | Clariant Plastics and Coatings (Dispersions) | Agrocer® Red 112 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of...voir plus Agrocer® Red 112 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of production equipment. Due to its composition, Agrocer® Red 112 disp. is highly compatible with common seed treatment pesticide formulations as well as seed coating products. In comparison to Pigment Red 48:2, Agrocer® Red 112 disp. exhibits superior compatibility in pesticide formulations and seed coatings. All Agrocer® dispersions are manufactured without using alkyl phenol ethoxylate (APEO) and do not require any hazardous labeling. voir moins | Request Sample |
| Agrocer® Red 482 Disp. | Clariant Plastics and Coatings (Dispersions) | Agrocer® Red 482 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of...voir plus Agrocer® Red 482 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of production equipment. Due to its composition, Agrocer® Red 482 disp. is highly compatible with common seed treatment pesticide formulations as well as seed coating products. All Agrocer® dispersions are manufactured without using alkyl phenol ethoxylate (APEO) and do not require any hazardous labeling. voir moins | Request Sample |
| Agrocer® Violet 023 Disp. | Clariant Plastics and Coatings (Dispersions) | Agrocer® Violet 023 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning...voir plus Agrocer® Violet 023 Disp. is an aqueous pigment dispersion that is recommended for the coloration of seeds. The pigment dispersions from the Agrocer® disp. range are easy to handle, readily pumpable for simple dosing and mixing and facilitate the cleaning of production equipment. Due to its composition, Agrocer® Violet 023 disp. is highly compatible with common seed treatment pesticide formulations as well as seed coating products. Agrocer® Violet 023 disp. gives very attractive color shades and seeds a high-quality appearance. All Agrocer dispersions are manufactured without using alkyl phenol ethoxylate (APEO) and do not require any hazardous labeling. voir moins | Request Sample |
| Aquanyl Blue AN 500 - Pigment Blue 15:0 | Clariant Plastics and Coatings (Dispersions) | Aquanyl Blue AN 500 is a water-based dispersion of Pigment Blue 15:0. It is binder-free, solvent-free and based on nonionic and / or anionic wetting and dispersing agents. Recommended for water-based paints and coatings. | Request Sample |
| Aquanyl® Red D3GD 500 - Pigment Red 254 | Clariant Plastics and Coatings (Dispersions) | Aquanyl® Red D3GD 500 is an aqueous pigment dispersion recommended for water-based coatings and paints. | Request Sample |
| Aquanyl Yellow YT 100 - Pigment Yellow 65 | Clariant Plastics and Coatings (Dispersions) | Aquanyl Yellow YT 100 is an aqueous pigment dispersion recommended for water-based coatings. | Request Sample |
| Colanyl Black N 131 - MX - Pigment Black 7 | Clariant Plastics and Coatings (Dispersions) | Colanyl Black N 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the ...voir plus Colanyl Black N 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the excellent weathering fastness, it is suitable for interior and exterior use. voir moins | Request Sample |
| Colanyl Black N 500 - Pigment Black 7 | Clariant Plastics and Coatings (Dispersions) | Colanyl Black N 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* The main app...voir plus Colanyl Black N 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* The main application fields of Colanyl Black N 500 are new generation of dispersion paints and renderings/plaster based on aqueous polymer dispersions. Colanyl Black N 500 is also compatible with some other binder systems, e.g. water-based industrial paints, but the maximum dosage level and compatibility of Colanyl Black N 500 has to be checked in the customer paint system itself. voir moins | Request Sample |
| Colanyl Blue A2R 131 - Pigment Blue 15:1 | Clariant Plastics and Coatings (Dispersions) | Colanyl Blue A2R 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of its...voir plus Colanyl Blue A2R 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of its good durability, it can be used for interior and exterior use after adequate weathering tests. voir moins | Request Sample |
| Colanyl Blue A2R 500 - Pigment Blue 15:1 | Clariant Plastics and Coatings (Dispersions) | Colanyl Blue A2R 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* The main ap...voir plus Colanyl Blue A2R 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* The main application fields of Colanyl Blue A2R 500 are new generation of dispersion paints and renderings/plaster based on aqueous polymer dispersions. Colanyl Blue A2R 500 is also compatible with some other binder systems, e.g. water-based industrial paints, but the maximum dosage level and compatibility of Colanyl Blue A2R 500 has to be checked in the customer paint system itself. By using Colanyl Blue A2R 500 in automatic and manual dispensers, excellent accuracy and reliability when poured or pumped have been observed. Furthermore, Colanyl Blue A2R 500 is miscible in all proportions with other Colanyl 500 preparations. By adding Colanyl Extender MS 530, the color strength of Colanyl Blue A2R 500 can be adjusted. voir moins | Request Sample |
| Colanyl Blue A4R 130-MX - Pigment 15:1 | Clariant Plastics and Coatings (Dispersions) | Colanyl Blue A4R 130-MX is a pigment dispersion based on phthalocyanine blue for water-based coatings. | Request Sample |
| Colanyl Blue B2G 131 - Pigment Blue 15:3 | Clariant Plastics and Coatings (Dispersions) | Colanyl Blue B2G 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of its...voir plus Colanyl Blue B2G 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of its good durability, it can be used for interior and exterior use after adequate weathering tests. voir moins | Request Sample |
| Colanyl Carmine FBB 133-MX - Pigment Red 146 | Clariant Plastics and Coatings (Dispersions) | Colanyl Carmine FBB 133-MX is an aqueous pigment dispersion based on PR 146 for water-based coatings. | Request Sample |
| Colanyl Extender MS 530 - Filler | Clariant Plastics and Coatings (Dispersions) | Colanyl Extender MS 530 is an aqueous binder-free pigment preparation based on a colorless inorganic extender and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC...voir plus Colanyl Extender MS 530 is an aqueous binder-free pigment preparation based on a colorless inorganic extender and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* voir moins | Request Sample |
| Colanyl Green GG 500 - Pigment Green 7 | Clariant Plastics and Coatings (Dispersions) | Colanyl Green GG 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Oxide Black B 530 - Pigment Black 11 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Black B 530 VP3206 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.*...voir plus Colanyl Oxide Black B 530 VP3206 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* Colanyl Oxide Black B 530 VP3206 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* voir moins | Request Sample |
| Colanyl Oxide Black IR 500 - Pigment Green 17 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Black IR 500 VP 5148 is a aqueous, binder-free pigment preparation and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation are compatible with water-based, VOC-free and VOC-low decorative co...voir plus Colanyl Oxide Black IR 500 VP 5148 is a aqueous, binder-free pigment preparation and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation are compatible with water-based, VOC-free and VOC-low decorative coatings.* Colanyl Oxide Black IR 500 VP 5148 is a aqueous, binder-free pigment preparation and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation are compatible with water based, VOC-free and VOC-low decorative coatings. voir moins | Request Sample |
| Colanyl Oxide Blue COR 530 - Pigment Blue 28 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Blue COR 530 VP3210 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings. | Request Sample |
| Colanyl Oxide Green G 530 - Pigment Green 17 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Green G 530 VP 3834 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings....voir plus Colanyl Oxide Green G 530 VP 3834 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* voir moins | Request Sample |
| Colanyl Oxide Red B 530 - Pigment Red 101 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Red B 530 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings. | Request Sample |
| Colanyl Oxide Red G 530 - Pigment Red 101 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Red G 530 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings. | Request Sample |
| Colanyl Oxide Yellow BV 530 - Pigment Yellow 184 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Yellow BV 530 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coating.* | Request Sample |
| Colanyl Oxide Yellow CR 530 - Pigment Brown 24 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Yellow CR 530 VP3198 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings...voir plus Colanyl Oxide Yellow CR 530 VP3198 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* voir moins | Request Sample |
| Colanyl Oxide Yellow R 132 - MX - Pigment Yellow 42 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Yellow R 132 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because ...voir plus Colanyl Oxide Yellow R 132 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the excellent weathering fastness, it is suitable for interior and exterior use. voir moins | Request Sample |
| Colanyl Oxide Yellow R 531- Pigment Yellow 42 | Clariant Plastics and Coatings (Dispersions) | Colanyl Oxide Yellow R 531 VP 3888 is a aqueous, binder-free pigment preparation and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation are compatible with water-based, VOC-free and VOC-low decorative co...voir plus Colanyl Oxide Yellow R 531 VP 3888 is a aqueous, binder-free pigment preparation and manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation are compatible with water-based, VOC-free and VOC-low decorative coatings. voir moins | Request Sample |
| Colanyl Pink E-WD 530 VP 5275 - Pigment Red 122 | Clariant Plastics and Coatings (Dispersions) | Colanyl Pink E-WD 530 VP 5275 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Red D3GD 500 - Pigment Red 254 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red D3GD 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Red E3B 500 - Pigment Violet 19 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red E3B 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Red E3B 500-MX - Pigment Violet 19 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red E3B 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Red F5RK 130 - MX - Pigment Red 170 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red F5RK 130 is an aqueous pigment dispersion based on PR 170 for water-based coatings. | Request Sample |
| Colanyl Red F5RK 500 - Pigment Red 170 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red F5RK 500 is a binder- and solvent-free, aqueous pigment preparation of Pigment Red 170 and based on nonionic and/or anionic wetting and dispersing agents. Recommended for water-based coatings. | Request Sample |
| Colanyl Red FGR 530 - Pigment Red 112 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red FGR 530 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Red FGRG 130 - MX - Pigment Red 112 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red FGRG 130 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the...voir plus Colanyl Red FGRG 130 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the moderate durability, it is suitable for interior use only. voir moins | Request Sample |
| Colanyl Red GG 131 - Pigment Orange 5 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red GG 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the m...voir plus Colanyl Red GG 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the moderate durability, it is suitable for interior use only. voir moins | Request Sample |
| Colanyl Red GG 500 - Pigment Orange 5 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red GG 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Red HF3S 500 - Pigment Red 188 | Clariant Plastics and Coatings (Dispersions) | Colanyl Red HF3S 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Scarlet GO 530 - Pigment Red 168 | Clariant Plastics and Coatings (Dispersions) | Colanyl Scarlet GO 530 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Violet RL 131 - Pigment Violet 23 | Clariant Plastics and Coatings (Dispersions) | Colanyl Violet RL 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of th...voir plus Colanyl Violet RL 131 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the moderate durability, it is suitable for interior use only. voir moins | Request Sample |
| Colanyl Violet RL 530 - Pigment Violet 23 | Clariant Plastics and Coatings (Dispersions) | Colanyl Violet RL 530 VP 5335 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl White R 500 - Pigment White 6 | Clariant Plastics and Coatings (Dispersions) | Colanyl White R 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl White RN 500 - MX - Pigment White 6 | Clariant Plastics and Coatings (Dispersions) | Colanyl White RN 500-MX is a very low VOC, water-based pigment preparation of Pigment White 6. It is binder-free, solvent-free and based on nonionic and/or anionic wetting and dispersing agents. Recommended for water-based paints and coatings. | Request Sample |
| Colanyl Yellow 2GXD 130 - Pigment Yellow 74 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow 2GXD 130 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of ...voir plus Colanyl Yellow 2GXD 130 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the moderate durability, it is suitable for interior use only. voir moins | Request Sample |
| Colanyl Yellow 2GXD 500 - Pigment Yellow 74 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow 2GXD 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Yellow 5GX 500 - Pigment Yellow 74 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow 5GX 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Yellow FGL 500 - Pigment Yellow 97 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow FGL 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Yellow G 132 - Pigment Yellow 1 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow G 132 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the...voir plus Colanyl Yellow G 132 is a binder-free, aqueous pigment preparation based on nonionic and/or anionic wetting and dispersing agents and propylene glycol. The product has a pourable and pumpable consistency and is suitable for dosing machines. Because of the moderate durability, it is suitable for interior use only. voir moins | Request Sample |
| Colanyl Yellow H3G 500 - Pigment Yellow 154 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow H3G 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Colanyl Yellow HRD 500 - Pigment Yellow 83 | Clariant Plastics and Coatings (Dispersions) | Colanyl Yellow HRD 500 is an aqueous binder-free pigment preparation manufactured without using alkyl phenol ethoxylated (APEO) additives. This aqueous pigment preparation is compatible with water-based low VOC and VOC-free decorative coatings.* | Request Sample |
| Easy Clean Coatings 1000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time...voir plus 3M™ Easy Clean Coating ECC-1000 is a fluoropolymer solution used for coating ceramic, glass and other non-porous surfaces. Once applied, the result is an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. voir moins | |
| Easy Clean Coatings 4000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-4000 is a fluoropolymer used for coating ceramic and glass surfaces. Once it air-dries, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. | |
| Easy Clean Coatings 6000 | 3M Advanced Materials Division | 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, he...voir plus 3M™ Easy Clean Coating ECC-6000 is a fluoropolymer solution used for coating non-porous ceramic, glass or metal oxide surfaces. Once it bonds with a substrate, it provides an “easy-to-clean” surface that resists staining, hard water deposits and soils, helping extend the time between cleanings. voir moins | |
| Hostafine Black T 30 - Pigment Black 7 | Clariant Plastics and Coatings (Dispersions) | Hostafine Black T 30 is a pigment dispersion of approx. 30% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Black 7. The extremly low particle size distribution gives an excellent...voir plus Hostafine Black T 30 is a pigment dispersion of approx. 30% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Black 7. The extremly low particle size distribution gives an excellent gloss, transparency and sedimentation properties in aqueous systems. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Black TS 30 - Pigment Black 7 | Clariant Plastics and Coatings (Dispersions) | Hostafine Black TS 30 is a pigment dispersion of approx. 33% pigment and is based on nonionic dispersing and wetting agents and is glycolfree. The Colour Index of the basic pigment is Pigment Black 7. The extremly low particle size distribution gives very...voir plus Hostafine Black TS 30 is a pigment dispersion of approx. 33% pigment and is based on nonionic dispersing and wetting agents and is glycolfree. The Colour Index of the basic pigment is Pigment Black 7. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. Mainly used in stationery, shoe care products and woodstains. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Blue B2G - Pigment Blue 15:3 | Clariant Plastics and Coatings (Dispersions) | Hostafine Blue B2G is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Blue 15:3. The extremly low particle size distribution gives very good gl...voir plus Hostafine Blue B2G is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Blue 15:3. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. Suitable for stationery, woodstains, latex, viscose fibres, detergents. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Brown HFR - Pigment Brown 25 | Clariant Plastics and Coatings (Dispersions) | Hostafine Brown HFR is an ultra fine pigment dispersion based on benzimidazolone brown for water-based coatings, inks and emulsions. | Request Sample |
| Hostafine Green GN - Pigment Green 7 | Clariant Plastics and Coatings (Dispersions) | Hostafine Green GN is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Green 7. The extremly low particle size distribution gives very good glos...voir plus Hostafine Green GN is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Green 7. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for stationery, woodstains, latex, viscose fibres and detergents. voir moins | Request Sample |
| Hostafine Magenta E - Pigment Red 122 | Clariant Plastics and Coatings (Dispersions) | Hostafine Magenta E is a pigment dispersion of approx. 20% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 122. The extremly low particle size distribution gives very good glo...voir plus Hostafine Magenta E is a pigment dispersion of approx. 20% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 122. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for ink jet inks, stationery, woodstains, latex, viscose fibres and detergents. voir moins | Request Sample |
| Hostafine Red F5RK - Pigment Red 170 | Clariant Plastics and Coatings (Dispersions) | Hostafine Red F5RK is a pigment preparation of approx. 35% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 170. The extremly low particle size distribution gives very good glo...voir plus Hostafine Red F5RK is a pigment preparation of approx. 35% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 170. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for woodstains, stationery and shoe polishes. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Red FGR - Pigment Red 112 | Clariant Plastics and Coatings (Dispersions) | Hostafine Red FGR is a pigment dispersion of approx. 45% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 112. The extremly low particle size distribution gives very good gloss...voir plus Hostafine Red FGR is a pigment dispersion of approx. 45% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 112. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. Hostafine Red FGR is suitable for stationery, woodstains, latex, viscose fibres and detergents. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Red HF3S - Pigment Red 188 | Clariant Plastics and Coatings (Dispersions) | Hostafine Red HF3S is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 188. The extremly low particle size distribution gives very good glos...voir plus Hostafine Red HF3S is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 188. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. Hostafine Red HF3S is suitable for stationery, woodstains, latex and viscose fibres. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Red P2GL - Pigment Red 179 | Clariant Plastics and Coatings (Dispersions) | Hostafine Red P2GL is a pigment dispersion of approx. 25% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 179. The extremly low particle size distribution gives very good glos...voir plus Hostafine Red P2GL is a pigment dispersion of approx. 25% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 179. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. Hostafine Red P2GL is suitable for stationery, woodstains, latex and viscose fibres where high lightfastness and weatherfastness is required. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Rubine F6B - Pigment Red 184 | Clariant Plastics and Coatings (Dispersions) | Hostafine Rubine F6B is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 184. The extremly low particle size distribution gives very good gl...voir plus Hostafine Rubine F6B is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Red 184. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. Hostafine Rubine F6B is suitable for stationery, woodstains, latex and viscose fibres. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Transoxide Red B 31 - Pigment Red 101 | Clariant Plastics and Coatings (Dispersions) | Hostafine Trans Oxide Red B 31 is a pigment preparation of approx. 35% pigment and is based on nonionic an anionic dispersing and wetting agents and polyglycol. The Colour Index of the basic pigment is Pigment Red 101. The extremly low particle size distr...voir plus Hostafine Trans Oxide Red B 31 is a pigment preparation of approx. 35% pigment and is based on nonionic an anionic dispersing and wetting agents and polyglycol. The Colour Index of the basic pigment is Pigment Red 101. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for woodstains and dispersion paints. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Tr.Ox. Yellow R 31- Pigment Yellow 42 | Clariant Plastics and Coatings (Dispersions) | Hostafine Trans Oxide Yellow R 31 is a pigment preparation of approx. 35% pigment and is based on nonionic an anionic dispersing and wetting agents and polyglycol. The Colour Index of the basic pigment is Pigment Yellow 42. The extremly low particle size ...voir plus Hostafine Trans Oxide Yellow R 31 is a pigment preparation of approx. 35% pigment and is based on nonionic an anionic dispersing and wetting agents and polyglycol. The Colour Index of the basic pigment is Pigment Yellow 42. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for woodstains and dispersion paints. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Violet RL - Pigment Violet 23 | Clariant Plastics and Coatings (Dispersions) | Hostafine Violet RL is a pigment dispersion of approx. 30% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Violet 23. The extremly low particle size distribution gives very good g...voir plus Hostafine Violet RL is a pigment dispersion of approx. 30% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Violet 23. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for stationery, woodstains, latex and viscose fibres. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Yellow GR 30 - Pigment Yellow 13 | Clariant Plastics and Coatings (Dispersions) | Hostafine Yellow GR 30 is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Yellow 13. The extremly low particle size distribution gives very goo...voir plus Hostafine Yellow GR 30 is a pigment dispersion of approx. 40% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Yellow 13. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for stationery, woodstains, latex, viscose fibres and detergents. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
| Hostafine Yellow HR 30 - Pigment Yellow 83 | Clariant Plastics and Coatings (Dispersions) | Hostafine Yellow HR 30 is a pigment dispersion of approx. 35% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Yellow 83. The extremly low particle size distribution gives very goo...voir plus Hostafine Yellow HR 30 is a pigment dispersion of approx. 35% pigment and is based on nonionic dispersing and wetting agents and glycol. The Colour Index of the basic pigment is Pigment Yellow 83. The extremly low particle size distribution gives very good gloss, transparency and sedimentation properties in aqueous systems. It is suitable for stationery, woodstains, latex, viscose fibres and detergents. Hostafine pigment preparations are especially suitable for water-based transparent wood stains. They can also be used for other applications such as aqueous emulsion paints, glass paints, water-colors, latex and water resistant inks, inks for fiber-tip fineliner and roller-tip pens. A final evaluation in the customer system is necessary. voir moins | Request Sample |
