| CF19-2186 | NuSil Silicone Technology 1 | CF19-2186 is a general purpose silicone elastomer that has a medium cure rate and is provided in mix and dispense applicators. This product can provide protection for assemblies and electronic components against, vibration, shock, ozone, moisture, dust an...もっと表示する CF19-2186 is a general purpose silicone elastomer that has a medium cure rate and is provided in mix and dispense applicators. This product can provide protection for assemblies and electronic components against, vibration, shock, ozone, moisture, dust and other contaminants. It can also be utilized as an encapsulating or potting material, and can replicate surfaces and devices. 表示を減らす | |
| EXOCOAT™ AM | Axcentive Sarl | EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down v...もっと表示する EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down viruses and bacteria. It eradicates viruses such as influenza, SARS-COV-2, dengue & hepatitis and bacteria such as E. coli, MSRA, streptococcus, listeria, pneumonia, and salmonella. It is activated by light and displays quick drying at room temperature. Spray application is recommended to reach thin monolayers. It exhibits curing at room temperature up to 300°C and super hard particles (1GPa Vickers). It is easy to apply & durable, allowing longer disinfection intervals while preserving hygiene level. It shows non-silver leaching, efficacious even under low light conditions, lower service frequency, and no need for frequent disinfection routine. It is used in the state-of-the-art continuous antimicrobial coating for high-traffic areas. EXOCOAT® AM is suitable for topcoats for any surface inside buildings, stores, hospitals, and vehicles. The shelf life of this product is 9 months. 表示を減らす | |
| Ketjenflex® 12 | Axcentive Sarl | Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl com...もっと表示する Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl compounds, and PVC based plastisols. It can also be used in PVC based polymers, nitrocellulose resins, and cyanoacrylate adhesives. 表示を減らす | |
| Ketjenflex® 6 | Axcentive Sarl | Ketjenflex® 6 is a toluene sulfonamide in the form of a white crystalline powder. It is used as a plasticizer in inks, adhesives, and coatings. Ketjenflex® 6 can be used with resins such as nitrocellulose, polyamide, PVAC, rosin, epoxy, and more. | |
| Ketjenflex® 8 | Axcentive Sarl | Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coa...もっと表示する Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coatings, synthetic polyamides, epoxy coatings and adhesives, and more. 表示を減らす | |
| Ketjenflex® CP | Axcentive Sarl | Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings. | |
| Ketjenflex® MH | Axcentive Sarl | Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printi...もっと表示する Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printing inks. 表示を減らす | |
| Ketjenflex® MS 80 | Axcentive Sarl | Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured in...もっと表示する Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured into desired formulations. It has applications in nitrocellulose coatings, cellulose acetate formulations, and printing inks. 表示を減らす | |
| LS-6140 | NuSil Silicone Technology 1 | LS-6140 is a two-part, optically clear silicone system that is based on a methyl silicone polymer, and has a low viscosity. It can be used for casting, injecting or bonding molidng of high performance optical components. It can also be used for photonics ...もっと表示する LS-6140 is a two-part, optically clear silicone system that is based on a methyl silicone polymer, and has a low viscosity. It can be used for casting, injecting or bonding molidng of high performance optical components. It can also be used for photonics applications that require a low outgassing and minimal volatile condensables to protect sensitive devices from condensation. 表示を減らす | |
| LS-6941 | NuSil Silicone Technology 1 | LS-6941 is an optical thermoset that is solvent free, and has a low viscosity. It will cure at room temperature or more rapidly when heat is added. It can be used for the bonding, casting or injecting molding of high performance optical components. This s...もっと表示する LS-6941 is an optical thermoset that is solvent free, and has a low viscosity. It will cure at room temperature or more rapidly when heat is added. It can be used for the bonding, casting or injecting molding of high performance optical components. This silicone is also ideal for applications that require index matching at 1.41. It is suitable for applications that require an operating temperature range of -65 to 240°C (–85 to 465°F). 表示を減らす | |
| R-1008-0 | NuSil Silicone Technology 1 | R-1008-0 is a translucent, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating mus...もっと表示する R-1008-0 is a translucent, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 表示を減らす | |
| R-1008-1 | NuSil Silicone Technology 1 | R-1008-1 is a white, RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating t...もっと表示する R-1008-1 is a white, RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F).This product can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. 表示を減らす | |
| R-1008-2 | NuSil Silicone Technology 1 | R-1008-2 is a black RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion, and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating t...もっと表示する R-1008-2 is a black RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion, and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F).This product can be used on silicone rubber parts as a marking ink where the coating must maintain long term stability. 表示を減らす | |
| R-1008-3 | NuSil Silicone Technology 1 | R-1008-3 is a red, non corrosive, flowable silicone elastomer dispersion that cures in 7 days at room temperature. This product is long lasting, and is used as a marking ink for silicone rubber parts as well as other components that require a coating with...もっと表示する R-1008-3 is a red, non corrosive, flowable silicone elastomer dispersion that cures in 7 days at room temperature. This product is long lasting, and is used as a marking ink for silicone rubber parts as well as other components that require a coating with long term stability. 表示を減らす | |
| R-1008-4 | NuSil Silicone Technology 1 | R-1008-4 is an orange, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must ma...もっと表示する R-1008-4 is an orange, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 表示を減らす | |
| R-1008-5 | NuSil Silicone Technology 1 | R-1008-5 is a yellow, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must mai...もっと表示する R-1008-5 is a yellow, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 表示を減らす | |
| R-1008-6 | NuSil Silicone Technology 1 | R-1008-6 is a green, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must main...もっと表示する R-1008-6 is a green, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 表示を減らす | |
| R-1008-7 | NuSil Silicone Technology 1 | R-1008-7 is a blue, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maint...もっと表示する R-1008-7 is a blue, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 表示を減らす | |
| R-1008-8 | NuSil Silicone Technology 1 | R-1008-8 is a violet, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must mai...もっと表示する R-1008-8 is a violet, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 表示を減らす | |
| R-2100-1 | NuSil Silicone Technology 1 | R-2100-1 is a white silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...もっと表示する R-2100-1 is a white silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 表示を減らす | |
| R-2100-2 | NuSil Silicone Technology 1 | R-2100-2 is a black silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...もっと表示する R-2100-2 is a black silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 表示を減らす | |
| R-2100-3 | NuSil Silicone Technology 1 | R-2100-3 is a red silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal ...もっと表示する R-2100-3 is a red silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 表示を減らす | |
| R-2100-6 | NuSil Silicone Technology 1 | R-2100-6 is a green silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...もっと表示する R-2100-6 is a green silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 表示を減らす |
