| 3M™ Ceramic Microspheres W-210 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M c...もっと表示する 3M™ Ceramic Microspheres White Grade W-210 are made of alkali alumino silicate ceramic and is one of our smallest high-strength ceramic particles with a typical d90 of 12 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-210 are typically chosen over other 3M ceramic microspheres for higher gloss formulations. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. 表示を減らす | |
| 3M™ Ceramic Microspheres W-410 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler load...もっと表示する 3M™ Ceramic Microspheres White Grade W-410 are made of high-strength alkali alumino silicate ceramic with a typical d90 of 21 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-410 are typically chosen over other 3M ceramic microspheres for their overall balance in properties. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. 表示を減らす | |
| 3M™ Ceramic Microspheres W-610 | 3M Advanced Materials Division | 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic m...もっと表示する 3M™ Ceramic Microspheres White Grade W-610 are made of alkali alumino silicate ceramic and is our largest high-strength ceramic particles with a typical d90 of 32 microns; it has a controlled particle size distribution. Formulating with these 3M ceramic microspheres allows higher filler loadings while maintaining desired properties such as viscosity control. In addition, these engineered particles are added to many paints and industrial coatings to provide scrub and burnish resistance. Due to their smaller particle size, 3M ceramic microspheres white grade W-610 are typically chosen over other 3M ceramic microspheres for increased durability. Formulators may be able to extend resin in their formulation by adding 3M ceramic microspheres and potentially reduce cost. 表示を減らす | |
| 3M™ Glass Bubbles iM16K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...もっと表示する 3M™ Glass Bubbles iM16K are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 16,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles iM30K | 3M Advanced Materials Division | 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...もっと表示する 3M™ Glass Bubbles iM30K are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 27,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K1 | 3M Advanced Materials Division | 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...もっと表示する 3M™ Glass Bubbles K1 are hollow glass spheres with a typical density of 0.125 g/cc and an isostatic crush strength of 250 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K15 | 3M Advanced Materials Division | 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles K15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K20 | 3M Advanced Materials Division | 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles K20 are hollow glass spheres with a typical density of 0.20 g/cc and an isostatic crush strength of 500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K25 | 3M Advanced Materials Division | 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles K25 are hollow glass spheres with a typical density of 0.25 g/cc and an isostatic crush strength of 750 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K37 | 3M Advanced Materials Division | 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...もっと表示する 3M™ Glass Bubbles K37 are hollow glass spheres with a typical density of 0.37 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K42HS | 3M Advanced Materials Division | 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...もっと表示する 3M™ Glass Bubbles K42HS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 7,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles K46 | 3M Advanced Materials Division | 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles SK46 are hollow glass spheres with a typical density of 0.46 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S15 | 3M Advanced Materials Division | 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths....もっと表示する 3M™ Glass Bubbles S15 are hollow glass spheres with a typical density of 0.15 g/cc and an isostatic crush strength of 300 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S22 | 3M Advanced Materials Division | 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths...もっと表示する 3M™ Glass Bubbles S22 are hollow glass spheres with a typical density of 0.22 g/cc and an isostatic crush strength of 400 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S28HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stren...もっと表示する 3M™ Glass Bubbles S28HS are hollow glass spheres with a typical density of 0.28 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S32 | 3M Advanced Materials Division | 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles S32 are hollow glass spheres with a typical density of 0.32 g/cc and an isostatic crush strength of 2,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S35 | 3M Advanced Materials Division | 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles S35 are hollow glass spheres with a typical density of 0.35 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S38 | 3M Advanced Materials Division | 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengt...もっと表示する 3M™ Glass Bubbles S38 are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 4,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S38HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush streng...もっと表示する 3M™ Glass Bubbles S38HS are hollow glass spheres with a typical density of 0.38 g/cc and an isostatic crush strength of 5,500 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S42XHS | 3M Advanced Materials Division | 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...もっと表示する 3M™ Glass Bubbles S42XHS are hollow glass spheres with a typical density of 0.42 g/cc and an isostatic crush strength of 8,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S60 | 3M Advanced Materials Division | 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strength...もっと表示する 3M™ Glass Bubbles S60 are hollow glass spheres with a typical density of 0.6 g/cc and an isostatic crush strength of 6,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles S60HS | 3M Advanced Materials Division | 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush stre...もっと表示する 3M™ Glass Bubbles S60HS are hollow glass spheres with a typical density of 0.60 g/cc and an isostatic crush strength of 18,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| 3M™ Glass Bubbles XLD3000 | 3M Advanced Materials Division | 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush str...もっと表示する 3M™ Glass Bubbles XLD3000 are hollow glass spheres with a typical density of 0.23 g/cc and an isostatic crush strength of 3,000 psi. 3M™ Glass Bubbles are lightweight hollow glass microspheres with a broad range of densities, particle sizes and crush strengths. These general purpose spheres offer very good strength-to-density ratio and making them suitable for a variety of uses in the paints and coatings industry. These microspheres are used in applications from specialty architectural and industrial paints to lightweight spackling, caulks, adhesives and roof coatings. Manufacturers use 3M glass bubbles for their ability to help reduce weight, improve reflectivity, reduce shrinkage, enhance surface appearance and help reduce overall material costs. 表示を減らす | |
| AC-67 | Ark (Fogang) Chemicals Industry Co., Ltd. | AC-67 is an β-(3,4-Epoxycyclohexyl) ethyltrimethoxysilane with the chemical structure CH2CH2Si(OCH3)3 and comes as a clear, colorless liquid. Primarily used in the production of adhesives and sealants, AC-67 can be used as an additive to improve acrylic e...もっと表示する AC-67 is an β-(3,4-Epoxycyclohexyl) ethyltrimethoxysilane with the chemical structure CH2CH2Si(OCH3)3 and comes as a clear, colorless liquid. Primarily used in the production of adhesives and sealants, AC-67 can be used as an additive to improve acrylic emulsions as well as used for filler in glass fiber surface treatments. 表示を減らす | |
| Accowear | Accoat A/S | Accowear is a reinforcement that is composed of a wear-resistant layer of stainless steel that is porous. It is used in conjunction with a fluoroplastic topcoat. The topcoat provides the non-stick properties while Accowear provides the wear-resistant prop...もっと表示する Accowear is a reinforcement that is composed of a wear-resistant layer of stainless steel that is porous. It is used in conjunction with a fluoroplastic topcoat. The topcoat provides the non-stick properties while Accowear provides the wear-resistant properties. 表示を減らす | |
| Acti-Gel® 208 | Active Minerals | Acti-Gel® 208 purified attapulgite is a high quality, self-dispersing hydrated magnesium aluminosilicate intended for high performance use as a binder, thixotrope, reinforcement additive and anti-settling agent. This unique formulary tool suspends and hom...もっと表示する Acti-Gel® 208 purified attapulgite is a high quality, self-dispersing hydrated magnesium aluminosilicate intended for high performance use as a binder, thixotrope, reinforcement additive and anti-settling agent. This unique formulary tool suspends and homogeneously disperses other particles in liquid systems creating a very stable mixture yet enables higher loadings of solids without increasing viscosity. Acti-Gel 208 additive can be a simple fix for syneresis, pigment float & flooding and sedimentation problems in a wide range of water-based coatings. Its low dosage, and extremely low residue makes it a quick “post-add” solution for stability problems in existing coating formulas without changing its rheology, paint formula or packaging label. 表示を減らす | Request Sample |
| Acti-Min® PG | Active Minerals | Acti-Min® PG air-float kaolin is a carefully produced, high quality, pigment extender designed for the paint industry. It provides desirable performance advantages in gloss and sheen control, enamel holdout, anti-settling, and sanding properties. As our h...もっと表示する Acti-Min® PG air-float kaolin is a carefully produced, high quality, pigment extender designed for the paint industry. It provides desirable performance advantages in gloss and sheen control, enamel holdout, anti-settling, and sanding properties. As our highest brightness product, Acti-Min® PG product can be a lbs-for-lbs direct replacement for higher cost water-washed kaolin products in coatings and similar applications. Its very fine and narrow particle size distribution in the 0.25 to 0.4 micron range has shown to be more effective at TiO2 extension in latex paint than standard water-washed kaolin grades. 表示を減らす | Request Sample |
| ADDAPT® SilStab HL+ | ADDAPT Chemicals BV | ADDAPT® SilStab HL+ is a solvent-free, stabilized potassium silicate solution with a hydrophobic component in water. It is added to textured masonry coatings and interior paints. This product improves scrub resistance, is non-foaming, and free of preserva...もっと表示する ADDAPT® SilStab HL+ is a solvent-free, stabilized potassium silicate solution with a hydrophobic component in water. It is added to textured masonry coatings and interior paints. This product improves scrub resistance, is non-foaming, and free of preservatives. 表示を減らす | |
| ADDAPT® SilStab L 100 | ADDAPT Chemicals BV | ADDAPT® SilStab L 100 is a solvent-free, stabilized potassium silicate solution in water. It is added to interior and exterior coatings as well as textured masonry coatings. This product is non-foaming, free of preservatives, and has anti-corrosion proper...もっと表示する ADDAPT® SilStab L 100 is a solvent-free, stabilized potassium silicate solution in water. It is added to interior and exterior coatings as well as textured masonry coatings. This product is non-foaming, free of preservatives, and has anti-corrosion properties when applied to ferrous surfaces. The high stability of ADDAPT® SilStab L 100 allows it to be added to coatings without causing coagulation, and no additional stabilizing additives are necessary. 表示を減らす | |
| ADDAPT® SilStab L 50 | ADDAPT Chemicals BV | ADDAPT® SilStab L 50 is a solvent-free, stabilized potassium silicate solution for coatings and plasters. It can be used as a primer on masonry surfaces and for anti-corrosion on ferrous metals. This product is soluble in water, non-foaming, and can be ad...もっと表示する ADDAPT® SilStab L 50 is a solvent-free, stabilized potassium silicate solution for coatings and plasters. It can be used as a primer on masonry surfaces and for anti-corrosion on ferrous metals. This product is soluble in water, non-foaming, and can be added to coatings without causing coagulation. 表示を減らす | |
| AEROSIL® R 9200 | Evonik Operations GmbH, BL Coating Additives | AEROSIL® R 9200 is a structure modified, hydrophobic fumed silica. | Request Sample |
| AKTIFIT AM | Hoffmann Mineral | AKTIFIT AM is an activated SILFIT Z 91, produced by modifying the surface with amino functional silane. It is used as a functional filler either on its own or combined with extenders or matting agents. An optimum effect will be obtained in polar elastomer...もっと表示する AKTIFIT AM is an activated SILFIT Z 91, produced by modifying the surface with amino functional silane. It is used as a functional filler either on its own or combined with extenders or matting agents. An optimum effect will be obtained in polar elastomers in combination with sulfur or sulfur donor, amine or bisphenolic crosslinking systems. This product can be used whenever high tensile strength and high modulus, combined with a very low tensile and compression set, are as important as excellent processing and extrusion properties. 表示を減らす | |
| AKTIFIT PF 111 | Hoffmann Mineral | AKTIFIT PF 111 is a calcined product, treated with alkyl silane. It is recommended for electrophoretic coatings, corrosion protection coatings, plastic primers, and interior dispersion paints. | |
| AKTIFIT PF 115 | Hoffmann Mineral | AKTIFIT PF 115 is an activated SILFIT Z 91, produced by modifying the surface with a special amino functional silane. The by-products split off during the treatment reac-tion are largely removed during the production process which firmly at-taches the sil...もっと表示する AKTIFIT PF 115 is an activated SILFIT Z 91, produced by modifying the surface with a special amino functional silane. The by-products split off during the treatment reac-tion are largely removed during the production process which firmly at-taches the silane to the filler sur-face. This helps minimize undesira-ble side effects, as they are poten-tially encountered with in situ mix-ing (direct addition of silane to the compound). 表示を減らす | |
| AKTIFIT Q | Hoffmann Mineral | AKTIFIT Q is an activated SILFIT Z 91, produced by modifying the surface with a methacrylic silane. The by-products split off during the treatment reaction are largely removed during the production process which firmly attaches the silane to the filler su...もっと表示する AKTIFIT Q is an activated SILFIT Z 91, produced by modifying the surface with a methacrylic silane. The by-products split off during the treatment reaction are largely removed during the production process which firmly attaches the silane to the filler surface. This helps minimize undesirable side effects, which are potentially encountered with in-situ mixing (direct addition of silane to the compound). 表示を減らす | |
| AKTIFIT VM | Hoffmann Mineral | AKTIFIT VM is an activated SILFIT Z 91 that can be used as a functional filler either on its own or combined with extenders or matting agents. The best effect is achieved in binder systems which polymerize or cure due to a radically initiated reaction. | |
| AKTISIL AM | Hoffmann Mineral | AKTISIL AM is an activated SILLITIN Z 86, produced by modifying the surface with amino functional silane. Used as a functional filler either on its own or combined with extenders or flatting agents. | |
| AKTISIL MAM | Hoffmann Mineral | AKTISIL MAM is an activated SILLITIN V 88, produced by modifying the surface with 3-methacryloxypropyl-trimethoxy silane. Can be used as a functional filler either on its own or combined with extenders or flatting agents. | |
| AKTISIL MAM-R | Hoffmann Mineral | AKTISIL MAM-R is an activated SILLITIN V 85, produced by modifying the surface with 3-methacryloxypropyl-trimethoxy silane. Used as a functional filler either on its own or combined with extenders or flatting agents. | |
| AKTISIL PF 777 | Hoffmann Mineral | AKTISIL PF 777 is an activated SILLITIN Z 86, produced by modifying the surface with alkyl silane. Used as a functional filler alone by itself, or in combination with rheological additives and/or flatting agents. | |
| AKTISIL VM 56 | Hoffmann Mineral | AKTISIL VM 56 is an activated SILLITIN Z 86, produced by modifying the surface with Vinyl-triethoxy silane. Used as a functional filler either on its own or combined with extenders or flatting agents. | |
| AKTISIL VM 56/89 | Hoffmann Mineral | AKTISIL VM 56/89 is an activated SILLITIN Z 89, produced by modifying the surface with 3-Vinyltriethoxy silane. Used as a functional filler either on its own or combined with extenders or flatting agents. | |
| ALBACAR® 5970 | Specialty Minerals | ALBACAR® 5970 is a mineral additive which has a narrow particle size distribution. This product has an oil absorption of 50 and a specific gravity of 2.7. ALBACAR® 5970 is used as a filler in paints, adhesives, sealants, caulks, and plastics. | |
| ALBACAR® 8101 | Specialty Minerals | ALBACAR® 8101 is a mineral additive which has a narrow particle size distribution. This product has an oil absorption of 36 and a specific gravity of 2.7. ALBACAR® 8101 is used as a filler in paints, adhesives, sealants, caulks, and plastics. | |
| ALBAFIL® | Specialty Minerals | ALBAFIL® is a fine, pure precipitated calcium carbonate which has a precisely controlled particle size and a narrow distribution. This product has an average particle size of 0.7 microns and a specific gravity of 2.7. ALBAFIL® is used in paints and coatin...もっと表示する ALBAFIL® is a fine, pure precipitated calcium carbonate which has a precisely controlled particle size and a narrow distribution. This product has an average particle size of 0.7 microns and a specific gravity of 2.7. ALBAFIL® is used in paints and coatings. 表示を減らす | |
| Almatis BayGranite®17 ATH (Aluminum Trihydroxide) | Almatis, Inc. | Almatis BayGranite®17 ATH (Aluminum Trihydroxide) is an inorganic hydrated alumina, primarily used as a flame retardant additive for most polymer systems. BayGranite® 17 is more accurately designated chemically as aluminum trihydroxide, Al(OH)3, and is pr...もっと表示する Almatis BayGranite®17 ATH (Aluminum Trihydroxide) is an inorganic hydrated alumina, primarily used as a flame retardant additive for most polymer systems. BayGranite® 17 is more accurately designated chemically as aluminum trihydroxide, Al(OH)3, and is produced through processing of alumina-bearing feedstocks. It is a dry powder, when heated above approximately 220°C it decomposes into approximately 35% water and 65% alumina by weight. 表示を減らす | |
| Almatis FlameGard® ATH (Aluminum Trihydroxide) | Almatis, Inc. | Almatis FlameGard® ATH (Aluminum Trihydroxide) is an inorganic hydrated alumina designed for use in polymer systems as a flame retardant and smoke suppressive additive. FlameGard is more accurately designated chemically as aluminum trihydroxide, Al(OH)3, ...もっと表示する Almatis FlameGard® ATH (Aluminum Trihydroxide) is an inorganic hydrated alumina designed for use in polymer systems as a flame retardant and smoke suppressive additive. FlameGard is more accurately designated chemically as aluminum trihydroxide, Al(OH)3, and is produced through processing of alumina-bearing feedstocks. Although FlameGard is a dry powder, when heated above approximately 220°C it decomposes into approximately 35% water and 65% alumina by weight. 表示を減らす | |
| Anhydrite | Provencale S.A. | Anhydrite is a filler that can withstand humidity. It is finely ground and dressed natural anhydrite that is a waterless sulphate. It is often formed as an evaporation product from sea water subject to progressive concentration of the salt water solution....もっと表示する Anhydrite is a filler that can withstand humidity. It is finely ground and dressed natural anhydrite that is a waterless sulphate. It is often formed as an evaporation product from sea water subject to progressive concentration of the salt water solution. Anhydrite makes up the sturdy solid base of gypsum deposits and can be mined separately. It is for use in industrial paints, lacquers and adhesives. 表示を減らす | |
| AnTec C-60 | Anpeak Specialty Minerals Co., Ltd. | AnTec C-60, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by a controlled heat treatment in order to remove crystalline-bound hydroxyl groups and to improve brightness. It can be used as an extende...もっと表示する AnTec C-60, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by a controlled heat treatment in order to remove crystalline-bound hydroxyl groups and to improve brightness. It can be used as an extender in paints and coatings. 表示を減らす | |
| AnTec C-98 | Anpeak Specialty Minerals Co., Ltd. | AnTec C-98, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by controlled heat treatment in order to remove crystalline-bound hydroxyl groups and in order to improve brightness. It can be used as a f...もっと表示する AnTec C-98, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by controlled heat treatment in order to remove crystalline-bound hydroxyl groups and in order to improve brightness. It can be used as a functional pigment extender in coatings, paints, and printing inks. 表示を減らす | |
| AnTec C-OP | Anpeak Specialty Minerals Co., Ltd. | AnTec C-OP, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by a controlled heat treatment in order to remove crystalline-bound hydroxyl groups and to remove brightness. It can be used in flat or low...もっと表示する AnTec C-OP, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by a controlled heat treatment in order to remove crystalline-bound hydroxyl groups and to remove brightness. It can be used in flat or low-sheen architectural paints. It can also serve as an ink receptacle in specialty paper applications. 表示を減らす | |
| AnTec MM | Anpeak Specialty Minerals Co., Ltd. | AnTec MM, in the form of a highly pulverized powder, is a high-reactivity metakaolin Pozzolan. This product can be used as an admixture in mortars and grouts, as well as in concrete masonry units or other cement-based products. Its specific gravity lies...もっと表示する AnTec MM, in the form of a highly pulverized powder, is a high-reactivity metakaolin Pozzolan. This product can be used as an admixture in mortars and grouts, as well as in concrete masonry units or other cement-based products. Its specific gravity lies between 2.5 and 2.7, and it contains less than .5% free moisture. 表示を減らす | |
| AnTec WE | Anpeak Specialty Minerals Co., Ltd. | AnTec WE, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by a controlled heat treatment in order to remove crystalline-bound hydroxyl groups. It can be used as an extender for pigment applications. ...もっと表示する AnTec WE, in the form of a highly pulverized powder, is a calcined kaolin. This product has been dehydroxylated by a controlled heat treatment in order to remove crystalline-bound hydroxyl groups. It can be used as an extender for pigment applications. It contains less than 0.5% free moisture at 105 degrees Celsius. 表示を減らす | |
| Anti-Reflective Application Nano Alumina B8013-2 | Tianjin Boyuan New Materials Co., Ltd. | B8013-2 has small particle size and excellent dispersibility, making is useful for anti-reflective coatings. It can be applied on photovoltaic glass and PET. It increases transmittance by way of decreasing light reflectance. | |
| Ballotini® A | Potters Industries Inc. | Ballotini® A is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 20-30 and a particle diameter range of 600-850 microns. Ballotini® A is most commonly used in metal finishing applications. | |
| Ballotini® AA | Potters Industries Inc. | Ballotini® AA is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 40-70 and a particle diameter range of 212-425 microns. Ballotini® AA is most commonly used in metal finishing applications. | |
| Ballotini® AAA | Potters Industries Inc. | Ballotini® AAA is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 25-45 and a particle diameter range of 355-710 microns. Ballotini® AAA is most commonly used in metal finishing applications. | |
| Ballotini® AB | Potters Industries Inc. | Ballotini® AB is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 50-80 and a particle diameter range of 180-300 microns. Ballotini® AB is most commonly used in metal finishing applications. | |
| Ballotini® AC | Potters Industries Inc. | Ballotini® AC is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 60-120 and a particle diameter range of 125-250 microns. Ballotini® AC is most commonly used in metal finishing applications. | |
| Ballotini® AD | Potters Industries Inc. | Ballotini® AD is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 70-140 and a particle diameter range of 106-212 microns. Ballotini® AD is most commonly used in metal finishing applications. | |
| Ballotini® AE | Potters Industries Inc. | Ballotini® AE is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 100-170 and a particle diameter range of 90-150 microns. Ballotini® AE is most commonly used in metal finishing applications. | |
| Ballotini® AG | Potters Industries Inc. | Ballotini® AG is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 120-270 and a particle diameter range of 53-125 microns. Ballotini® AG is most commonly used in metal finishing applications. | |
| Ballotini® AH | Potters Industries Inc. | Ballotini® AH is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 170-325 and a particle diameter range of 45-90 microns. Ballotini® AH is most commonly used in metal finishing applications. | |
| Ballotini® B | Potters Industries Inc. | Ballotini® B is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 30-40 and a particle diameter range of 425-600 microns. Ballotini® B is most commonly used in metal finishing applications. | |
| Ballotini® C | Potters Industries Inc. | Ballotini® C is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 40-60 and a particle diameter range of 250-425 microns. Ballotini® C is most commonly used in metal finishing applications. | |
| Ballotini® D | Potters Industries Inc. | Ballotini® D is a transparent, colorless, spherical glass microbead. This product has a US Sieve size of 50-70 and a particle diameter range of 212-300 microns. Ballotini® D is most commonly used in metal finishing applications. | |
| Ballotini® MIL 10 | Potters Industries Inc. | Ballotini® MIL 10 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 100-170 and a particle diameter range of 90-150 microns. Ballotini® MIL 10 is most commonly used in metal finishing application...もっと表示する Ballotini® MIL 10 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 100-170 and a particle diameter range of 90-150 microns. Ballotini® MIL 10 is most commonly used in metal finishing applications. 表示を減らす | |
| Ballotini® MIL 11 | Potters Industries Inc. | Ballotini® MIL 11 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 120-200 and a particle diameter range of 75-125 microns. Ballotini® MIL 11 is most commonly used in metal finishing application...もっと表示する Ballotini® MIL 11 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 120-200 and a particle diameter range of 75-125 microns. Ballotini® MIL 11 is most commonly used in metal finishing applications. 表示を減らす | |
| Ballotini® MIL 12 | Potters Industries Inc. | Ballotini® MIL 12 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 140-230 and a particle diameter range of 63-106 microns. Ballotini® MIL 12 is most commonly used in metal finishing application...もっと表示する Ballotini® MIL 12 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 140-230 and a particle diameter range of 63-106 microns. Ballotini® MIL 12 is most commonly used in metal finishing applications. 表示を減らす | |
| Ballotini® MIL 13 | Potters Industries Inc. | Ballotini® MIL 13 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 170-325 and a particle diameter range of 45-90 microns. Ballotini® MIL 13 is most commonly used in metal finishing applications...もっと表示する Ballotini® MIL 13 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 170-325 and a particle diameter range of 45-90 microns. Ballotini® MIL 13 is most commonly used in metal finishing applications. 表示を減らす | |
| Ballotini® MIL 3 | Potters Industries Inc. | Ballotini® MIL 3 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 20-30 and a particle diameter range of 600-850 microns. Ballotini® MIL 3 is most commonly used in metal finishing applications. | |
| Ballotini® MIL 4 | Potters Industries Inc. | Ballotini® MIL 4 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 30-40 and a particle diameter range of 425-600 microns. Ballotini® MIL 4 is most commonly used in metal finishing applications. | |
| Ballotini® MIL 5 | Potters Industries Inc. | Ballotini® MIL 5 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 40-50 and a particle diameter range of 300-425 microns. Ballotini® MIL 5 is most commonly used in metal finishing applications. | |
| Ballotini® MIL 6 | Potters Industries Inc. | Ballotini® MIL 6 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 50-70 and a particle diameter range of 212-300 microns. Ballotini® MIL 6 is most commonly used in metal finishing applications. | |
| Ballotini® MIL 7 | Potters Industries Inc. | Ballotini® MIL 7 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 60-80 and a particle diameter range of 180-250 microns. Ballotini® MIL 7 is most commonly used in metal finishing applications. | |
| Ballotini® MIL 8 | Potters Industries Inc. | Ballotini® MIL 8 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 70-100 and a particle diameter range of 150-212 microns. Ballotini® MIL 8 is most commonly used in metal finishing applications. | |
| Ballotini® MIL 9 | Potters Industries Inc. | Ballotini® MIL 9 is a military-grade, transparent, colorless, spherical glass microbead. This product has a US Sieve size of 80-120 and a particle diameter range of 125-180 microns. Ballotini® MIL 9 is most commonly used in metal finishing applications. | |
| Barifine® BF Series | Kowa American Corporation | Barifine® BF Series are inorganic encapsulated pigment particles which are highly transparent for use as functional extenders, for haze-free gloss and highly smooth films through hyper-filling effects, for maximizing optical brightness, and to control alu...もっと表示する Barifine® BF Series are inorganic encapsulated pigment particles which are highly transparent for use as functional extenders, for haze-free gloss and highly smooth films through hyper-filling effects, for maximizing optical brightness, and to control aluminum pigment orientation in metallic coatings. They find use in automotive, consumer electronics, printing inks and other markets. 表示を減らす | Request Sample |
| Barifine® BF-1 | Kowa American Corporation | Barifine® BF-1 is a highly transparent, chemically inert ultrafine barium sulfate that is a part of KOWA's Barifine® Series. This product provides haze-free gloss and highly smooth film by its hyper filling effect for solvent-born paint. Barifine® encapsu...もっと表示する Barifine® BF-1 is a highly transparent, chemically inert ultrafine barium sulfate that is a part of KOWA's Barifine® Series. This product provides haze-free gloss and highly smooth film by its hyper filling effect for solvent-born paint. Barifine® encapsulated pigment particles maximize their original brightness. Some recommended uses of this product are automotive topcoat, automotive surfacer, appliance coatings, inks, and plastics. 表示を減らす | Request Sample |
| Barifine® BF-10 | Kowa American Corporation | Barifine® BF-10 is a highly transparent, chemically inert ultrafine barium sulfate that is a part of KOWA's Barifine® Series. This product provides haze-free gloss and highly smooth film by its hyper filling effect for solvent-born paint. Barifine® encaps...もっと表示する Barifine® BF-10 is a highly transparent, chemically inert ultrafine barium sulfate that is a part of KOWA's Barifine® Series. This product provides haze-free gloss and highly smooth film by its hyper filling effect for solvent-born paint. Barifine® encapsulated pigment particles maximize their original brightness. Some recommended uses of this product are automotive topcoat, automotive surfacer, appliance coatings, inks, and plastics. 表示を減らす | Request Sample |
| Barifine® BF-20 | Kowa American Corporation | Barifine® BF-20 (Barium sulfate) is a chemically stable substance with high heat, chemical & water resistance and increased weatherability. It is classified as a precipitated barium sulfate or a synthetic product and a ground barite obtained by pulverizi...もっと表示する Barifine® BF-20 (Barium sulfate) is a chemically stable substance with high heat, chemical & water resistance and increased weatherability. It is classified as a precipitated barium sulfate or a synthetic product and a ground barite obtained by pulverizing natural ores. It is used as a general extender pigment because of its relatively high specific gravity and low refractive index. 表示を減らす | Request Sample |
| Barifine® BF-21 | Kowa American Corporation | Barifine® BF-21 is an excellent dispersion with superior transparency in water-born coatings due to surface treatment. This product shows improvement in the haze-free gloss and jetness of black paints; as well as in the haze-free gloss and saturation of o...もっと表示する Barifine® BF-21 is an excellent dispersion with superior transparency in water-born coatings due to surface treatment. This product shows improvement in the haze-free gloss and jetness of black paints; as well as in the haze-free gloss and saturation of organic color pigments. Some recommended uses of this product include automotive topcoat and automotive surfacer by water-born coatings. It is also used in water-born coatings and water-born inks. 表示を減らす | Request Sample |
| Barifine® BF-25 | Kowa American Corporation | Barifine® BF-25 is an excellent dispersion with superior transparency in water-born coatings due to surface treatment. This product shows improvement in the haze-free gloss and jetness of black paints; as well as in the haze-free gloss and saturation of o...もっと表示する Barifine® BF-25 is an excellent dispersion with superior transparency in water-born coatings due to surface treatment. This product shows improvement in the haze-free gloss and jetness of black paints; as well as in the haze-free gloss and saturation of organic color pigments. Some recommended uses of this product include automotive topcoat and automotive surfacer by water-born coatings. It is also used in water-born coatings and water-born inks. 表示を減らす | Request Sample |
| Barifine® BF-26 | Kowa American Corporation | Barifine® BF-26 is an excellent dispersion with superior transparency in water-born coatings due to surface treatment. This product shows improvement in the haze-free gloss and jetness of black paints; as well as in the haze-free gloss and saturation of o...もっと表示する Barifine® BF-26 is an excellent dispersion with superior transparency in water-born coatings due to surface treatment. This product shows improvement in the haze-free gloss and jetness of black paints; as well as in the haze-free gloss and saturation of organic color pigments. Some recommended uses of this product include automotive topcoat and automotive surfacer by water-born coatings. It is also used in water-born coatings and water-born inks. 表示を減らす | Request Sample |
| Barifine® BF-40 | Kowa American Corporation | Barifine® BF-40 is a highly transparent, chemically inert, ultrafine barium sulfate that is a part of KOWA's Barifine® Series. This product provides haze-free gloss and highly smooth film by its hyper filling effect for solvent-born paint. Barifine® encap...もっと表示する Barifine® BF-40 is a highly transparent, chemically inert, ultrafine barium sulfate that is a part of KOWA's Barifine® Series. This product provides haze-free gloss and highly smooth film by its hyper filling effect for solvent-born paint. Barifine® encapsulated pigment particles maximize their original brightness. Some recommended uses of this product are automotive topcoat, automotive surfacer, appliance coatings, inks, and plastics. 表示を減らす | Request Sample |
| Bariflor® 8010 | Minerals Girona S.A. | Bariflor® 8010 has a top cut at 10 μm. It is a barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. | |
| Bariflor® 8015 | Minerals Girona S.A. | Bariflor® 8015 is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. It has an oil absorption DOP of 14g/100g and a density o...もっと表示する Bariflor® 8015 is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. It has an oil absorption DOP of 14g/100g and a density of 4'35g/cm³. 表示を減らす | |
| Bariflor® 8025 | Minerals Girona S.A. | Bariflor® 8025 is a barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. It has an oil absorption DOP of 13g/100g and a density o...もっと表示する Bariflor® 8025 is a barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. It has an oil absorption DOP of 13g/100g and a density of 4'35g/cm³. 表示を減らす | |
| Bariflor® 8040 | Minerals Girona S.A. | Bariflor® 8040 has an oil absorption DOP of 12g/100g and a density of 4'35g/cm³. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmosph...もっと表示する Bariflor® 8040 has an oil absorption DOP of 12g/100g and a density of 4'35g/cm³. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8060 | Minerals Girona S.A. | Bariflor® 8060 has an oil absorption DOP of 11g/100g and a density of 4'35g/cm³. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmosph...もっと表示する Bariflor® 8060 has an oil absorption DOP of 11g/100g and a density of 4'35g/cm³. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8080 | Minerals Girona S.A. | Bariflor® 8080 has an oil absorption DOP of 10g/100g and a top cut of 80µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric ...もっと表示する Bariflor® 8080 has an oil absorption DOP of 10g/100g and a top cut of 80µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8410 | Minerals Girona S.A. | Bariflor® 8410 has an oil absorption DOP of 14g/100g and a top cut of 10µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric ...もっと表示する Bariflor® 8410 has an oil absorption DOP of 14g/100g and a top cut of 10µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8415 | Minerals Girona S.A. | Bariflor® 8415 has an oil absorption DOP of 13g/100g and a top cut of 20µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric ...もっと表示する Bariflor® 8415 has an oil absorption DOP of 13g/100g and a top cut of 20µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8425 | Minerals Girona S.A. | Bariflor® 8425 has an oil absorption DOP of 12g/100g and a top cut of 30µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric ...もっと表示する Bariflor® 8425 has an oil absorption DOP of 12g/100g and a top cut of 30µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8440 | Minerals Girona S.A. | Bariflor® 8440 has an oil absorption DOP of 11g/100g and a top cut of 40µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric ...もっと表示する Bariflor® 8440 has an oil absorption DOP of 11g/100g and a top cut of 40µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8460 | Minerals Girona S.A. | Bariflor® 8460 has an oil absorption DOP of 10g/100g and a top cut of 60µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric ...もっと表示する Bariflor® 8460 has an oil absorption DOP of 10g/100g and a top cut of 60µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Bariflor® 8480 | Minerals Girona S.A. | Bariflor® 8480 has an oil absorption DOP of 9g/100g and a top cut of 80µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric a...もっと表示する Bariflor® 8480 has an oil absorption DOP of 9g/100g and a top cut of 80µm. It is a Barium sulphate (Baryte) of high purity for use in systems where a high grade of brightness is not required, but calls for inertia and resistance to acids and atmospheric agents. 表示を減らす | |
| Barinit® 7025 | Minerals Girona S.A. | Barinit® 7025 has an oil absorption DOP of 14g/100g and a top cut of 30µm. It is a Barium Sulphate of good quality, for use in systems where the degree of brightness is not of importance. Its high specific weight and resistance to acids and atmospheric ag...もっと表示する Barinit® 7025 has an oil absorption DOP of 14g/100g and a top cut of 30µm. It is a Barium Sulphate of good quality, for use in systems where the degree of brightness is not of importance. Its high specific weight and resistance to acids and atmospheric agents make it a suitable product for industrial production of adhesives, putties, sound proofing and friction. 表示を減らす | |
| Barinit® 7040 | Minerals Girona S.A. | Barinit® 7040 has an oil absorption DOP of 13g/100g and a top cut of 40µm. It is a Barium Sulphate of good quality, for use in systems where the degree of brightness is not of importance. Its high specific weight and resistance to acids and atmospheric ag...もっと表示する Barinit® 7040 has an oil absorption DOP of 13g/100g and a top cut of 40µm. It is a Barium Sulphate of good quality, for use in systems where the degree of brightness is not of importance. Its high specific weight and resistance to acids and atmospheric agents make it a suitable product for industrial production of adhesives, putties, sound proofing and friction. 表示を減らす | |
| Barinit® 7060 | Minerals Girona S.A. | Barinit® 7025 has an oil absorption DOP of 12g/100g and a top cut of 60µm. It is a Barium Sulphate of good quality, for use in systems where the degree of brightness is not of importance. Its high specific weight and resistance to acids and atmospheric ag...もっと表示する Barinit® 7025 has an oil absorption DOP of 12g/100g and a top cut of 60µm. It is a Barium Sulphate of good quality, for use in systems where the degree of brightness is not of importance. Its high specific weight and resistance to acids and atmospheric agents make it a suitable product for industrial production of adhesives, putties, sound proofing and friction. 表示を減らす |
