| BLUESIL ADD 10086 | Elkem Silicones | BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints ...veja mais BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints and silicone binders. veja menos | |
| BLUESIL ADD 11013 | Elkem Silicones | BLUESIL ADD 11013 is a polyether-modified polydimethylsiloxane for use in solventless paints and varnishes, and in water-based paints and inks. | |
| BLUESIL BP 9200 | Elkem Silicones | BLUESIL BP 9200 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9300 | Elkem Silicones | BLUESIL BP 9300 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9705 | Elkem Silicones | BLUESIL BP 9705 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL BP 9710 | Elkem Silicones | BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and...veja mais BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and it does not contain ecotoxic surfactant. After it has dried on the surface, BLUESIL BP 9710 repels water and allows walls to breathe. Experience acquired over more than 40 years shows that silicone water repellents are a good answer to humidity problems in construction materials, particularly when for esthetical reasons the natural aspect of the material should be preserved. BLUESIL BP 9710 has been awarded a test certificate by CSTC (Centre Scientifique et Technique de - ): ref HD-340/133-151 on the 2006.02.20. veja menos | |
| BLUESIL BP 9800 | Elkem Silicones | BLUESIL BP 9800 is an aqueous APE-free polymethylsiloxane resin emulsion. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9821 | Elkem Silicones | BLUESIL BP 9821 is an aqueous APE-free polymethylsiloxane resin emulsion with low VOC content. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9878 | Elkem Silicones | BLUESIL BP 9878 is an aqueous polymethylsiloxane resin emulsion.This emulsion provides two fundamental properties of the silicone technology to the paint film: water repellency and permeability to water vapour. | |
| BLUESIL BP 9900 | Elkem Silicones | BLUESIL BP 9900 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive for building materials. | |
| BLUESIL BP 9920 | Elkem Silicones | BLUESIL BP 9920is anon-ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL EMUL 1803 | Elkem Silicones | BLUESIL EMUL 1803 is a non-ionic silicone emulsion containing silicone oil and resin. This emulsion is intended for mould-release of cast polyurethane elastomers. | |
| BLUESIL EMUL 269 | Elkem Silicones | BLUESIL EMUL 269 is an aqueous emulsion of an hydrogeno polysiloxane. | |
| BLUESIL EMUL 284 | Elkem Silicones | BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening prop...veja mais BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening properties (textile applications). veja menos | |
| BLUESIL EMUL 3500 | Elkem Silicones | BLUESIL EMUL 3500 is a general purpose; non-ionic oil in water silicone emulsion, of a high viscosity hydroxyl terminated polysiloxane. | |
| BLUESIL EMUL 35B | Elkem Silicones | BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream...veja mais BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream, neither during storage nor in use.Perfect stability in contact with hard water or zinc (i.e. in galvanized metal containers).Excellent heat stability after dilution.Very good wetting power. veja menos | |
| BLUESIL EMUL 55 | Elkem Silicones | BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component...veja mais BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component elements making up polishes and cleaners for artificial leather fabrics (PVC, PUR) and furniture polishes. veja menos | |
| BLUESIL EMUL 872 | Elkem Silicones | BLUESIL EMUL 872 is a slightly anionic aqueous emulsion with a 60% dry content, for general purposes. This is a concentrated version of BLUESIL EMUL E1P. | |
| BLUESIL EMUL E1P | Elkem Silicones | BLUESIL EMUL E1P is an oil in water emulsion containing 35 % of a silicone oil. It can be used in many industries. | |
| BLUESIL EMUL E1P U1 | Elkem Silicones | BLUESIL EMUL E1P U1 is a general purpose, non-ionic, aqueous silicone emulsion. | |
| BLUESIL EMULSION 2400 | Elkem Silicones | BLUESIL EMUL 2400 is a general purpose; non-ionic oil in water silicone emulsion of a methyl-hydrogen polysiloxane. | |
| BLUESIL FLD 21625 | Elkem Silicones | BLUESIL FLD 21625is anα/ω-epoxy functionalised polydimethylsiloxane fluid. | |
| BLUESIL FLD 45 | Elkem Silicones | BLUESIL FLD 45 is a low viscosity dimethylpolysiloxane oil used to prevent floating and flooding and improve leveling of air-drying paints. | |
| BLUESIL FLD 47V1 000 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V100 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V350 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V50 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V500 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL PI 2074 | Elkem Silicones | BLUESIL PI 2074 is a cationic photoinitiator for use with epoxy resins, vinyl ethers or any other type of oligomer which polymerises cationically. It is also suited to the formulation of hybrid radical / cationic systems. | |
| BLUESIL RES 6405 | Elkem Silicones | BLUESIL RES 6405 is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6405X | Elkem Silicones | BLUESIL RES 6405X is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6406XM | Elkem Silicones | BLUESIL RES 6406XM is a 60% solids methylphenylsilicone resin in Xylene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6407 | Elkem Silicones | BLUESIL RES 6407 is a 70% solids methylphenylsilicone resin in Toluene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6482X | Elkem Silicones | BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It i...veja mais BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It is also more compatible than other silicones with urea-formaldehyde, melamine-formaldehyde, epoxy, polyurethane and acrylic resins. Another use is as an additive for epoxy paints. It also improves weathering resistance. veja menos | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL TCS 7001 | Elkem Silicones | BLUESIL TCS 7001 is an alkyl polysiloxane solution in solvent phase specifically developed for the waterproofing of fabrics and leathers exposed to difficult weather conditions by spraying or impregnating. | |
| CAF 2534 | Elkem Silicones | CAF 2534 is a one component silicone rubber that cures when in contact with air humidity. It is intended for use as a formulation base for the development of tie-coats in the fouling release treatment of boat hulls. | |
| Doublecure® 173 | Double Bond Chemical Ind., Co., Ltd. | Doublecure® 173 is a liquid-type non-yellowing photoinitiator. Good solvency proprieties make it ideal for making photoinitiator blends. It is the initiator of choice for coating on wood, metal and plastic as well as UV-cured adhesives. Doublecure® 173, w...veja mais Doublecure® 173 is a liquid-type non-yellowing photoinitiator. Good solvency proprieties make it ideal for making photoinitiator blends. It is the initiator of choice for coating on wood, metal and plastic as well as UV-cured adhesives. Doublecure® 173, when irradiating with UV light, undergoes a homolytic and intramolecular type of breakage to generate a pair of free radicals to initiate the olymerization of UV curable systems. It does not require hydrogen donor to initiate its radicals. However its radicals are very sensitive to oxygen in the air. This product is a light yellow to clear liquid. veja menos | |
| Doublecure® 1819 | Double Bond Chemical Ind., Co., Ltd. | Doublecure® 1819 is a photoinitiator for polymerization of unsaturated resins upon UV light exposure. It is suggested to be used in white pigmented formulations, the curing of glass fiber reinforced polyester/styrene systems, and for clearcoats of outdoor...veja mais Doublecure® 1819 is a photoinitiator for polymerization of unsaturated resins upon UV light exposure. It is suggested to be used in white pigmented formulations, the curing of glass fiber reinforced polyester/styrene systems, and for clearcoats of outdoor use in combinations with light stabilizers. With low concentrations of this white-yellowish powder, it can reach an excellent curing performance in highly opaque white and colored furniture coatings or screen inks containing titanium dioxide or colored pigments, and presents minimum yellowing after exposure to sufficient amounts of UV radiation. In addition, it allows curing of thick sections due to the outstanding absorption. veja menos | |
| Doublecure® 184 | Double Bond Chemical Ind., Co., Ltd. | Doublecure® 184 is used for the application on non-yellowing UV Radiation Curing Systems. It is an alpha cleavage type photoinitiator, which combines the characteristics of high photospeed and exceptional storage life. Its non-yellowing and low-irritating...veja mais Doublecure® 184 is used for the application on non-yellowing UV Radiation Curing Systems. It is an alpha cleavage type photoinitiator, which combines the characteristics of high photospeed and exceptional storage life. Its non-yellowing and low-irritating properties, makes it an ideal choice for clear coatings on paper, flooring, metal, plastics and wood. Doublecure® 184, when irradiating with UV light, undergoes a homolytic and intramolecular type of breakage to generate a pair of free radicals to initiate the polymerization of UV curable systems. It does not require hydrogen donor to initiate its radicals. However, its radicals are very sensitive to oxygen in the air. Doublecure® 184 is strongly recommended when non-yellowing properties are crucial. Results obtained from an outdoor exposure study show that it gives better long-term non-yellowing performance than other initiators. Furthermore, it exhibits lower sensitivity to air inhibition than Doublecure® 173 during curing. veja menos | |
| Doublecure® 200 | Double Bond Chemical Ind., Co., Ltd. | Doublecure® 200 is a liquid-type non-yellowing photosensitizer. Good solvency proprieties make it ideal for making photoinitiator blends. It is the initiator of choice for coating on wood, metal and plastic as well as UV-cured adhesives where non-yellowin...veja mais Doublecure® 200 is a liquid-type non-yellowing photosensitizer. Good solvency proprieties make it ideal for making photoinitiator blends. It is the initiator of choice for coating on wood, metal and plastic as well as UV-cured adhesives where non-yellowing properties are important. This product, when irradiating with UV light, undergoes both of a homolytic and intramolecular type of breakage to generate a pair of free radicals and a bimolecular hydrogen abstraction reaction to initiate the polymerization of UV curable systems. Its photospeed acting as a photoinitiator is not as fast as Doublecure® 173 for example, but it gives better non-yellowing performance and better surface curing. This product is a light yellow and clear liquid. veja menos | |
| Doublecure® 369 | Double Bond Chemical Ind., Co., Ltd. | Doublecure® 369 is a highly efficient Free Radical Type I solid photoinitiator for UV-polymerization of chemically prepolymers in combination with mono-or multifunctional monomers. This pale yellow powder may be used after adequate testing alone or in com...veja mais Doublecure® 369 is a highly efficient Free Radical Type I solid photoinitiator for UV-polymerization of chemically prepolymers in combination with mono-or multifunctional monomers. This pale yellow powder may be used after adequate testing alone or in combination with suitable coinitiators, e.g., Doublecure® 184, for UV curable inks and varnishes for applications on paper, metal and plastic materials. Its high absorptivity makes it especially suitable for pigmented UV-curable systems, photo resists and printing plates. veja menos | |
| Doublecure® 575 | Double Bond Chemical Ind., Co., Ltd. | Doublecure® 575 is a liquid-type non-yellowing photosensitizer. It is the initiator of choice for coating on wood, metal and plastic as well as UV-cured adhesives where non-yellowing properties are important. This product can be used for printing ink, ove...veja mais Doublecure® 575 is a liquid-type non-yellowing photosensitizer. It is the initiator of choice for coating on wood, metal and plastic as well as UV-cured adhesives where non-yellowing properties are important. This product can be used for printing ink, overprint vanishes, wood lacquers, putties and fillers for particle board and chipboard, and adhesive. veja menos | |
| Doublecure® TPO | Double Bond Chemical Ind., Co., Ltd. | Doublecure® TPO is a photo initiator for UV coatings. Since it has a minor λmax located in 379 nm, it can be used for pigmented systems without sacrificing activity. Also due to its unprecedented speed and non-yellowing properties, it is the best recommen...veja mais Doublecure® TPO is a photo initiator for UV coatings. Since it has a minor λmax located in 379 nm, it can be used for pigmented systems without sacrificing activity. Also due to its unprecedented speed and non-yellowing properties, it is the best recommendation for thick film and white pigmented coating. This product is a yellow crystalline powder. Basically, a percentage of 1 – 3 % of Doublecure® TPO is effective for lacquer preparation. If the resin is made of polyester, there is no need for co-initiators. However, due to its sensitivity toward oxygen inhibition, additional co-initiators such as Doublecure® 184 or 173 is highly recommended for pigmented acrylic finishes. If the yellowing is not concerned, amine synergist such as Doublecure® EPD or P-115 is also beneficial to the throughcure. veja menos | |
| Doublecure® TPO-L | Double Bond Chemical Ind., Co., Ltd. | Doublecure® TPO-L is a photoinitiator for UV coatings. Since it has a minor λmax located in 379 nm, it can be used for pigmented systems without sacrificing activity. Also due to its unprecedented speed and non-yellowing properties, it is the best recomme...veja mais Doublecure® TPO-L is a photoinitiator for UV coatings. Since it has a minor λmax located in 379 nm, it can be used for pigmented systems without sacrificing activity. Also due to its unprecedented speed and non-yellowing properties, it is the best recommendation for thick film and white pigmented coating. Basically, a percentage of 1 – 3 % of Doublecure® TPO-L is effective for lacquer preparation. If the resin is made of polyester, there is no need for coinitiators. However, due to its sensitivity toward oxygen inhibition, additional coinitiators such as Doublecure® 184 or 173 is highly recommended for pigmented acrylic finishes. If the yellowing is not concerned, amine synergist such as Doublecure® EPD or P-115 is also beneficicial to the throughcure. Owing to its absorption of light in the long wave UV region, Doublecure® TPO-L and lacquers produced from it are daylight-sensitive. Therefore, light with wavelengths less than 500 nm must be excluded during storage and processing. veja menos | |
| DOUBLEMER® 1710 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 1710 is a modified bisphenol A epoxy diacrylate oligomer, and has better adhesion than standard bisphenol A epoxy diacrylate oligomer. This resin is characterized by fast cure, light color, chemical and heat resistance with high gloss and hardn...veja mais DOUBLEMER® 1710 is a modified bisphenol A epoxy diacrylate oligomer, and has better adhesion than standard bisphenol A epoxy diacrylate oligomer. This resin is characterized by fast cure, light color, chemical and heat resistance with high gloss and hardness. It belongs to the most common typical UV oligomer used in various UV/EB applications such as inks, coatings and overprinting varnishes. veja menos | |
| DOUBLEMER® 1720 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 1720 is a modified bisphenol A epoxy diacrylate oligomer, and has better adhesion than standard bisphenol A epoxy diacrylate oligomer. This resin is characterized by fast cure, light color, chemical and heat resistance with high gloss and hardn...veja mais DOUBLEMER® 1720 is a modified bisphenol A epoxy diacrylate oligomer, and has better adhesion than standard bisphenol A epoxy diacrylate oligomer. This resin is characterized by fast cure, light color, chemical and heat resistance with high gloss and hardness. It belongs to the most common typical UV oligomer used in various UV/EB applications such as inks, coatings and overprinting varnishes. veja menos | |
| DOUBLEMER® 188 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 188 is a high functional aromatic urethane acrylate oligomer diluted with 20-25% TMPTA, which provides very fast cure response when exposed to Ultraviolet Light (UV) or an Electron Beam (EB). Cured films of DOUBLEMER®188 exhibit excellent hardn...veja mais DOUBLEMER® 188 is a high functional aromatic urethane acrylate oligomer diluted with 20-25% TMPTA, which provides very fast cure response when exposed to Ultraviolet Light (UV) or an Electron Beam (EB). Cured films of DOUBLEMER®188 exhibit excellent hardness and solvent resistance. Formulated UV/EB curable products containing DOUBLEMER® 188 may be applied via lithographic, screen, gravure, direct or reverse roll and curtain coating methods. This product is recommended for use in: lithographic inks; improving cure speed, solvent resistance, and gloss; scratch resistant coating on plastic; and photo-imaginable soldier mask. veja menos | |
| DOUBLEMER® 193-TT60 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 193-TT60 is epoxy diacrylate oligomer with 60% diluents. This resin is characterized by fast cure, light color, chemical and heat resistance with high gloss, flexibility and toughness. It belongs to the most common typical UV oligomer used in v...veja mais DOUBLEMER® 193-TT60 is epoxy diacrylate oligomer with 60% diluents. This resin is characterized by fast cure, light color, chemical and heat resistance with high gloss, flexibility and toughness. It belongs to the most common typical UV oligomer used in various UV/EB applications such as inks, coatings and overprinting varnishes. veja menos | |
| DOUBLEMER® 6575 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 6575 is a 100% solid content oligomer designed for wood coating. It shows high matting efficiency, high reactivity, excellent hardness, excellent water resistance and excellent leveling. | |
| DOUBLEMER® 6915 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 6915 is a 100% solid content oligomer designed for plastic coating. It shows high matting efficiency, high reactivity, excellent hardness, excellent water resistance and excellent leveling. | |
| DOUBLEMER® 6MX75 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® 6MX75 is an acrylate oligomer. It shows excellent adhesion, fast curing, low shrinkage, good aluminum powder orientation, good anti-yellowing and excellent leveling. DOUBLEMER® 6MX75 can also be used as an adhesion promoter, to decrease coating...veja mais DOUBLEMER® 6MX75 is an acrylate oligomer. It shows excellent adhesion, fast curing, low shrinkage, good aluminum powder orientation, good anti-yellowing and excellent leveling. DOUBLEMER® 6MX75 can also be used as an adhesion promoter, to decrease coating shrinkage, and to improve matting efficiency. veja menos | |
| DOUBLEMER® UCP-0011-4 | Double Bond Chemical Ind., Co., Ltd. | DOUBLEMER® UCP-0011-4 is designed as a UV-curable soft touch coating for packaging boxes, receptacles or electronic devices. It is characterized by soft touch, good scratch resistance, good solvent resistance, and easy sprayability. | |
| LYNDCOAT 15 RTU | Elkem Silicones | LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RT...veja mais LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RTU also helps keep molds and vents clean, reducing defects and downtime. Lyndcoat™ 15 RTU typically is durable through multiple production cycles. The need for reapplication is dependent on factors such as the rubber compound, curing time, curing temperature, tread design and application technique. Lyndcoat™ 15 RTU is designed for processes requiring low viscosity mold lubricants. veja menos | |
| LYNDCOAT BR 1100 RTU | Elkem Silicones | LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the c...veja mais LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1100 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1100 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as Lyndcoat™ BR2101 RTU is highly recommended. veja menos | |
| LYNDCOAT BR 1102 | Elkem Silicones | LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the c...veja mais LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1102 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1102 RTU is of medium viscosity and does not contain mica. veja menos | |
| LYNDCOAT BR 1103 RTU | Elkem Silicones | LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the c...veja mais LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR1103 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. LYNDCOAT® BR1103 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as LYNDCOAT® BR2201 RTU is highly recommended. veja menos | |
| LYNDCOAT BR 1110 RTU | Elkem Silicones | LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers ...veja mais LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. LYNDCOAT BR 1110 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. LYNDCOAT BR 1110 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as LYNDCOAT BR 2101 RTU, is highly recommended. veja menos | |
| LYNDCOAT BR 1211 | Elkem Silicones | LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtim...veja mais LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtimes. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. veja menos | |
| LYNDCOAT BR 1214 | Elkem Silicones | LYNDCOAT BR 1214 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It is particularly friction resistant and slip promoting. Applied on the inside of the green...veja mais LYNDCOAT BR 1214 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It is particularly friction resistant and slip promoting. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. veja menos | |
| LYNDCOAT BR 1623 RTU | Elkem Silicones | LYNDCOAT BR 1623 RTU is a ready to use, silicone based, medium mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coatin...veja mais LYNDCOAT BR 1623 RTU is a ready to use, silicone based, medium mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. Lyndcoat BR 1623 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. Lyndcoat BR 1623 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as Lyndcoat XR 3900 Primer, is highly recommended. veja menos | |
| LYNDCOAT BR 1812 | Elkem Silicones | LYNDCOAT BR 1812 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR 1812 RTU replace...veja mais LYNDCOAT BR 1812 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR 1812 RTU replaces the conventional lining cements and solvent-based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR 1812 RTU does not contain aromatic or chlorinated solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR 1812 RTU is of low viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. veja menos | |
| LYNDCOAT BR 2100 RTU | Elkem Silicones | LYNDCOAT BR 2100 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures durable performance. | |
| LYNDCOAT BR 2104 | Elkem Silicones | LYNDCOAT BR 2104 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a long lasting multi release and slip performance. It was designed to...veja mais LYNDCOAT BR 2104 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a long lasting multi release and slip performance. It was designed to reduce build up notably in the bead area. veja menos | |
| LYNDCOAT BR 2201 | Elkem Silicones | LYNDCOAT BR 2201 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR 2201 replaces t...veja mais LYNDCOAT BR 2201 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR 2201 replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR 2201 does not contain aromatic or chlorinated solvents. It is easy to use and can be brushed, swabbed, or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. LYNDCOAT® BR 2201 is of high viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. veja menos | |
| LYNDCOAT BR 2204 A1 | Elkem Silicones | LYNDCOAT BR 2204 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build...veja mais LYNDCOAT BR 2204 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build up notably in the bead area. veja menos | |
| LYNDCOAT BR 2204 E4 | Elkem Silicones | LYNDCOAT BR 2204 E4 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce b...veja mais LYNDCOAT BR 2204 E4 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build up notably in the bead area. veja menos | |
| LYNDCOAT BR 2511 RTU | Elkem Silicones | LYNDCOAT BR2511 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines long lasting multi release with excellent slip and exceptional air bleed performan...veja mais LYNDCOAT BR2511 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines long lasting multi release with excellent slip and exceptional air bleed performance. veja menos | |
| LYNDCOAT BR 2512 | Elkem Silicones | LYNDCOAT BR2512 is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines particularly long lasting multi release and slip with exceptional air bleed performanc...veja mais LYNDCOAT BR2512 is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines particularly long lasting multi release and slip with exceptional air bleed performance. veja menos | |
| LYNDCOAT BR 601 RTU | Elkem Silicones | LYNDCOAT BR-601 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-601 RTU rep...veja mais LYNDCOAT BR-601 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-601 RTU replaces the conventional lining cements and solvent-based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR-601 RTU does not contain any solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR-601 RTU is of medium viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. veja menos | |
| LYNDCOAT BR 790 RTU | Elkem Silicones | LYNDCOAT BR 790 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-790 RTU rep...veja mais LYNDCOAT BR 790 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-790 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR-790 RTU does not contain any solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR-790 RTU is of low viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. veja menos | |
| LYNDCOAT MR 5100 RTU | Elkem Silicones | LYNDCOAT MR 5100 RTU is a ready to use, solvent free, water based coating designed for use in tire moulds. It is a blend of polymers that cure at typical molding temperatures to form a clear, tough, coating with a strong bond to the metal mould, possessin...veja mais LYNDCOAT MR 5100 RTU is a ready to use, solvent free, water based coating designed for use in tire moulds. It is a blend of polymers that cure at typical molding temperatures to form a clear, tough, coating with a strong bond to the metal mould, possessing excellent release and lubrication properties towards rubber. LYNDCOAT MR 5100 RTU helps keep moulds and vents clean, which reduces defects and downtime. LYNDCOAT MR 5100 RTU is durable through multiple production cycles. The need for reapplication is dependent on factors such as: the rubber compound, tread design, curing time, curing temperature, application technique and press type. LYNDCOAT MR 5100 RTU is designed for processes requiring low viscosity mould lubricants. veja menos | |
| PolyQ® 102 | Double Bond Chemical Ind., Co., Ltd. | PolyQ® 102 is an efficient reactive photoinitiator specially designed for application where odorless and improved non-migration properties are required, such as for food package coating. Its use in combination with a photoactivator such as Doublecure® 115...veja mais PolyQ® 102 is an efficient reactive photoinitiator specially designed for application where odorless and improved non-migration properties are required, such as for food package coating. Its use in combination with a photoactivator such as Doublecure® 115 should give results comparable to other benzophenone type initiators. This product is a benzophenone derivative oligomer. It appears as a crystalline semi-solid at room temperature. veja menos | |
| PolyQ 1100 | Double Bond Chemical Ind., Co., Ltd. | PolyQ 1100 is a macromolecular initiator with high efficiency, low odor, low migration, and low yellowing characteristics. It is recommended for use in plastic, paper, metal and fiber varnish; adhesives, inks, and food packaging inks. | |
| PolyQ 1150 | Double Bond Chemical Ind., Co., Ltd. | PolyQ 1150 is an oligomeric polyfunctional ɑ-hydroxyketone macromolecular initiator. It has the characteristics of high efficiency, low odor, low migration, low yellowing. It is recommended for plastic, paper, metal, and fiber varnishes, as well as for ad...veja mais PolyQ 1150 is an oligomeric polyfunctional ɑ-hydroxyketone macromolecular initiator. It has the characteristics of high efficiency, low odor, low migration, low yellowing. It is recommended for plastic, paper, metal, and fiber varnishes, as well as for adhesives and inks. veja menos | |
| SILBIONE CAF 72576 RED | Elkem Silicones | SILBIONE CAF 72576 RED is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 a...veja mais SILBIONE CAF 72576 RED is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. veja menos | |
| SILBIONE CAF 72589 | Elkem Silicones | SILBIONE CAF 72589 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat natural or agglomerated bottle corks. SILBIONE CAF 72589 is a solventless product based on reactive polymethyl siloxan...veja mais SILBIONE CAF 72589 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat natural or agglomerated bottle corks. SILBIONE CAF 72589 is a solventless product based on reactive polymethyl siloxane oils and inert fillers. It can be used as a release coating for materials intended for food contact. veja menos | |
| SILBIONE DISPERSION CAF 70004 | Elkem Silicones | SILBIONE DISPERSION CAF 70004 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat agglomerated bottle corks and especially champagne corks. SILBIONE DISPERSION CAF 70004 is a product based ...veja mais SILBIONE DISPERSION CAF 70004 is a one component silicone elastomer, curing at room temperature on contact with atmospheric humidity, used to treat agglomerated bottle corks and especially champagne corks. SILBIONE DISPERSION CAF 70004 is a product based on reactive polymethyl siloxane oils and inert fillers. It can be used as a release coating for materials intended for food contact. veja menos | |
| SILBIONE DISPERSION CAF 71500 GRY | Elkem Silicones | SILBIONE DISPERSION CAF 71500 GRY is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS ...veja mais SILBIONE DISPERSION CAF 71500 GRY is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. veja menos | |
| SILBIONE DISPERSION CAF 71528 | Elkem Silicones | SILBIONE DISPERSION CAF 71528 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF ...veja mais SILBIONE DISPERSION CAF 71528 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. veja menos | |
| SILBIONE DISPERSION CAF 71550 | Elkem Silicones | SILBIONE DISPERSION CAF 71550 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF ...veja mais SILBIONE DISPERSION CAF 71550 is a one component silicone rubber crosslinking at room temperature by reacting with the moisture in the air. These SILBIONE products contain reactive polydimethylsiloxane oils and inert fillers. The SILBIONE DISPERSIONS CAF 71550 and 71528 are supplied as cyclohexane dispersions (70% solids). The SILBIONE DISPERSION CAF 71500G is supplied as cyclohexane dispersions (50% solids). The SILBIONE CAF 72576 is a 100% solids product. They can be used separately as non-stick coatings for materials in contact with foodstuffs. They can also be used in these applications in the form of a two-layer system which boosts their performance. The product obtained after crosslinking only contains substances that are in conformity with a number of Food Contact legislations. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coating obtained have been correctly applied, in particular to avoid any risk of migration of constituents. veja menos | |
| SILBIONE RES 76405 | Elkem Silicones | SILBIONE RESINE 76405 is a polymethylphenyl-siloxane resin supplied as 50% solution in toluene. SILBIONE RESINE 76405 is used as release coating for materials that will be in contact with foodstuff. This resin can also be used as a binder in paints develo...veja mais SILBIONE RESINE 76405 is a polymethylphenyl-siloxane resin supplied as 50% solution in toluene. SILBIONE RESINE 76405 is used as release coating for materials that will be in contact with foodstuff. This resin can also be used as a binder in paints developed to protect and decorate these materials. The products obtained after crosslinking of SILBIONE RESINE 76405 contain only substances permitted by the Food Contact regulations currently in force. Contact BS for more detailed information. Important remarks: Manufacturers of paints, varnishes or coatings must naturally make sure that the other constituents in their formulas (solvents, pigments, additives, etc.) also comply with the regulations. They must also check that the coatings obtained have been correctly applied, in particular to avoid any risk of migration of constituents. veja menos | |
| SILCOLAPSE 120 | Elkem Silicones | SILCOLAPSE 120 is a 100% active compound containing polydimethylsiloxane oil and silica with an excellent behaviour in a large range of pH. SILCOLAPSE 120 is mainly intended for treatment of organic and anhydrous foaming systems. It can also be used in aq...veja mais SILCOLAPSE 120 is a 100% active compound containing polydimethylsiloxane oil and silica with an excellent behaviour in a large range of pH. SILCOLAPSE 120 is mainly intended for treatment of organic and anhydrous foaming systems. It can also be used in aqueous medium. SILCOLAPSE 120 is designed exclusively for industrial use. veja menos | |
| SILCOLAPSE 416 | Elkem Silicones | SILCOLAPSE 416 is a compound based on polydimethyl siloxane oil and silica. It has the characteristic of being easy to disperse in most foaming mediums. | |
| SILCOLAPSE 426R | Elkem Silicones | SILCOLAPSE 426R is a non-ionic aqueous emulsion based on polydimethylsiloxane oil. It has 30% active matter content and is recommended for the prevention, control or elimination of foam in aqueous systems. | |
| SILCOLAPSE 495 | Elkem Silicones | SILCOLAPSE 495 is a high performance silicone antifoam emulsion designed for use in a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm solids, even at elevated temperatures and under ...veja mais SILCOLAPSE 495 is a high performance silicone antifoam emulsion designed for use in a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm solids, even at elevated temperatures and under pressure. SILCOLAPSE 495 gives good results at wide-ranging pH and is effective under highly alkaline or acidic conditions. veja menos | |
| SILCOLAPSE 496 | Elkem Silicones | SILCOLAPSE 496 is a high performance silicone antifoam emulsion designed for use in severe environmental storage conditions and a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm soli...veja mais SILCOLAPSE 496 is a high performance silicone antifoam emulsion designed for use in severe environmental storage conditions and a wide range of aqueous industrial applications. The product effectively controls foam at concentrations as low as 10 ppm solids, even at elevated temperatures and under pressure. SILCOLAPSE 496 gives good results at wideranging pH and is effective under highly alkaline or acidic conditions. The emulsion is freezeprotected to less than -10°C and is stable upon thawing even after repeated freeze thaw cycles below -40°C veja menos | |
| SILCOLAPSE 5020 | Elkem Silicones | SILCOLAPSE 5020 is a non-ionic aqueous emulsion containing dimethylpolysiloxane, and is highly effective for prevention, control and elimination of foam in aqueous media. SILCOLAPSE 5020 contains 20% of active ingredient and is designed for industrial use...veja mais SILCOLAPSE 5020 is a non-ionic aqueous emulsion containing dimethylpolysiloxane, and is highly effective for prevention, control and elimination of foam in aqueous media. SILCOLAPSE 5020 contains 20% of active ingredient and is designed for industrial uses. Other specialized defoaming agents exist for use in food contact please consult us about them. veja menos | |
| SILCOLAPSE C525 | Elkem Silicones | SILCOLAPSE C525 is a silicone antifoam emulsion with very good water dispersibility and antifoaming efficiency in different aqueous systems. It shows very good stability with side range of pH value. | |
| SILCOLEASE 7611 | Elkem Silicones | SILCOLEASE 7611 is a kind of tri-component solventless type paper release system:Silcolease 7611 (base polymer)Silcolease crosslinker 321(crosslinker)Silcolease catalyst 91B (catalyst). | |
| SILCOLEASE ADD 107 | Elkem Silicones | SILCOLEASE ADD 107 is a silicone based additive used with a reactive solvent based silicone polymer system used for release coating of papers, films and various substrates. It has been especially designed to give excellent long term anchorage of the relea...veja mais SILCOLEASE ADD 107 is a silicone based additive used with a reactive solvent based silicone polymer system used for release coating of papers, films and various substrates. It has been especially designed to give excellent long term anchorage of the release system on PET film both when laminated against adhesives and reeled as coated film. veja menos | |
| SILCOLEASE ADD 382 | Elkem Silicones | SILCOLEASE ADD 382 is a silicone based additive used with a reactive solventless silicone polymer system for POLYESTER (PET) FILM RELEASE COATING applications. | |
| SILCOLEASE ADD 702 | Elkem Silicones | SILCOLEASE ADD 702 is a white, granular powder, freely soluble in water and possessing a slight odour of ammonia. It is used with emulsion SILCOLEASE polyaddition or polycondensation release systems to improve hold-out of the silicone. | |
| SILCOLEASE CATA 11091 M | Elkem Silicones | SILCOLEASE CATALYST 11091 M is a platinum complex mainly used as a catalyst of the solventless SILCOLEASE release systems. | |
| SILCOLEASE CATA 12070 | Elkem Silicones | SILCOLEASE CATALYST 12070 is a platinum complex mainly used as a catalyst of the solventless SILCOLEASE release systems. |
