| Antioxidant SN-1 | Tiarco Chemical | Antioxidant SN-1 is a highly active, non-discoloring secondary antioxidant with low volatility. It can be used with primary phenolic and amine antioxidants. Unlike other thioesters, this product may be used in both uncured and sulfur cured latex compounds...展开 Antioxidant SN-1 is a highly active, non-discoloring secondary antioxidant with low volatility. It can be used with primary phenolic and amine antioxidants. Unlike other thioesters, this product may be used in both uncured and sulfur cured latex compounds, and the maximum benefits are best noticed when used in combination with a primary antioxidant in natural and synthetic polymers. It is used in light colored or black compounds such as carpet backing foams, scrim adhesives, SBR latex stabilization, rubber based adhesives, footwear compounds and mechanical goods, and more. 收起 | |
| BLACK PEARLS® 4040 | Cabot Corporation - Additives | BLACK PEARLS® 4040 is a specialty carbon black for long-term ultraviolet and weatherability protection, good surface smoothness and dispersion performance. This product is well suited for use in a range of film and sheet applications, such as mulch and si...展开 BLACK PEARLS® 4040 is a specialty carbon black for long-term ultraviolet and weatherability protection, good surface smoothness and dispersion performance. This product is well suited for use in a range of film and sheet applications, such as mulch and silage film, irrigation pipe and tape, and general purpose film and sheet. 收起 | |
| BLUESIL PRIM 10073 | Elkem Silicones | BLUESIL PRIM 10073 is a product intended to improve the adhesion of BLUESIL one-component and two-component elastomers to metals and certain painted surfaces. The product is available as a ready-to-use solution of reactants diluted in a solvent. | |
| BLUESIL PRIM 12076 | Elkem Silicones | BLUESIL PRIM 12076 is a compound intended to improve the adhesion of one- or two-component room temperature vulcanising silicone elastomers. BLUESIL PRIM 12076 can be used on most porous surfaces. It comes as a colourless, ready to use solution of reactan...展开 BLUESIL PRIM 12076 is a compound intended to improve the adhesion of one- or two-component room temperature vulcanising silicone elastomers. BLUESIL PRIM 12076 can be used on most porous surfaces. It comes as a colourless, ready to use solution of reactants diluted in a solvent. 收起 | |
| BLUESIL RES 8152P | Elkem Silicones | BLUESIL RES 8152P is a 50% solids methylphenylsilicone resin in Toluene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 8170P | Elkem Silicones | BLUESIL RES 8170P is used to manufacture rigid insulators in the high pressure process: laminates based on glass fabric, mica (mica paper), mica/glass composite fabric and asbestos. It offers outstanding mechanical properties. | |
| BLUESIL RES 8360M | Elkem Silicones | BLUESIL RES 8360M is a methyl silicone resin supplied as a solution in toluene and intended for the manufacture of flexible insulants. | |
| BLUESIL SLT 10B OFF WHITE | Elkem Silicones | BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low ...展开 BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. 收起 | |
| BLUESIL SLT 10B PVC WHITE | Elkem Silicones | BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low ...展开 BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. 收起 | |
| BLUESIL SLT 10T OFF WHITE | Elkem Silicones | BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low m...展开 BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. BLUESIL SLT 10T adheres without a primer on virtually all surfaces found in building construction and accepts movements of 25% in continuous service within a wide range of temperatures. 收起 | |
| BLUESIL SLT 10T PVC WHITE | Elkem Silicones | BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low m...展开 BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. BLUESIL SLT 10T adheres without a primer on virtually all surfaces found in building construction and accepts movements of 25% in continuous service within a wide range of temperatures. 收起 | |
| BLUESIL SLT 3B BLACK | Elkem Silicones | BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of...展开 BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of 25 % throughout a wide temperature range resistance to severe weathering is excellent. 收起 | |
| BLUESIL SLT 3B TRANSLUCENT | Elkem Silicones | BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of...展开 BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of 25 % throughout a wide temperature range resistance to severe weathering is excellent. 收起 | |
| BLUESIL SLT 3B WHITE | Elkem Silicones | BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of...展开 BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of 25 % throughout a wide temperature range resistance to severe weathering is excellent. 收起 | |
| BLUESIL SLT 3E BLACK | Elkem Silicones | BLUESIL SLT 3E is a one-component silicone sealant which, when exposed to atmospheric humidity, forms a flexible and durable elastomeric seal which possesses excellent resistance to severe weathering conditions. | |
| BLUESIL SLT 3E TRANSLUCENT | Elkem Silicones | BLUESIL SLT 3E is a one-component silicone sealant which, when exposed to atmospheric humidity, forms a flexible and durable elastomeric seal which possesses excellent resistance to severe weathering conditions. | |
| BLUESIL SLT 3E WHITE | Elkem Silicones | BLUESIL SLT 3E is a one-component silicone sealant which, when exposed to atmospheric humidity, forms a flexible and durable elastomeric seal which possesses excellent resistance to severe weathering conditions. | |
| BLUESIL SLT 3S TRANSLUCENT | Elkem Silicones | BLUESIL SLT 3S is a one-component, moisture-cured silicone sealant which contains a fungicide. It cures at room temperature to form a flexible, medium modulus watertight joint for general sanitary sealing. | |
| BLUESIL SLT 3S WHITE | Elkem Silicones | BLUESIL SLT 3S is a one-component, moisture-cured silicone sealant which contains a fungicide. It cures at room temperature to form a flexible, medium modulus watertight joint for general sanitary sealing. | |
| BLUESIL SLT 4S TRANSCLUCENT | Elkem Silicones | BLUESIL SLT 4S is a one-component, moisture-cure silicone sealant which contains a fungicide. It cures at room temperature to form a flexible, low modulus watertight joint for general sanitary sealing. | |
| BLUESIL SLT AQUARIUM BLACK | Elkem Silicones | BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modu...展开 BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modulus of elasticity. BLUESIL SLT AQUARIUM offers excellent resistance to climatic ageing. 收起 | |
| BLUESIL SLT AQUARIUM TRANSLUCENT | Elkem Silicones | BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modu...展开 BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modulus of elasticity. BLUESIL SLT AQUARIUM offers excellent resistance to climatic ageing. 收起 | |
| BLUESIL SLT NOVART S TRANSLUCENT | Elkem Silicones | BLUESIL SLT NOVART S is a one component, neutral (alcoxy) and fast curing, ready-to-use silicone elastomer suitable for weather sealing and bonding seals in construction applications, which is protected by a fungicide. It crosslinks at room temperature to...展开 BLUESIL SLT NOVART S is a one component, neutral (alcoxy) and fast curing, ready-to-use silicone elastomer suitable for weather sealing and bonding seals in construction applications, which is protected by a fungicide. It crosslinks at room temperature to give a flexible seal of low modulus. 收起 | |
| BLUESIL SLT NOVART TRANSLUCENT | Elkem Silicones | BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL ...展开 BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL SLT NOVART can withstand movement of 25 % in constant service throughout a wide temperature range. 收起 | |
| BLUESIL SLT NOVART WHITE | Elkem Silicones | BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL ...展开 BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL SLT NOVART can withstand movement of 25 % in constant service throughout a wide temperature range. 收起 | |
| BLUESIL SLT VEC 90 BLACK | Elkem Silicones | BLUESIL SLT VEC 90 is a one-component silicone elastomer with high mechanical properties mainly intended for applications using so called Structural Glazing technique. It cures at room temperature and in the presence of air humidity to form a strong, fle...展开 BLUESIL SLT VEC 90 is a one-component silicone elastomer with high mechanical properties mainly intended for applications using so called Structural Glazing technique. It cures at room temperature and in the presence of air humidity to form a strong, flexible seal. 收起 | |
| BLUESIL SLT VEC 99A BLACK | Elkem Silicones | BLUESIL SLT VEC 99 is a two-component silicone elastomer with a high modulus of elasticity. After homogeneous mixing of parts A and B, the paste-like product transforms quickly at room temperature into an elastic material with outstanding mechanical and ...展开 BLUESIL SLT VEC 99 is a two-component silicone elastomer with a high modulus of elasticity. After homogeneous mixing of parts A and B, the paste-like product transforms quickly at room temperature into an elastic material with outstanding mechanical and adhesion properties. Its advantage, relative to conventional two-component elastomers lies in the large tolerance relative to the accuracy of the ratio A/B. BLUESIL SLT VEC 99 has been specially designed to meet requirements in Structural Glazing applications. 收起 | |
| BLUESIL SLT VI 10 BLACK | Elkem Silicones | BLUESIL SLT VI 10 is a one component, odourless, ready to use neutral silicone elastomer mainly used as second barrier seal in the Double Glazing market. It cures at room temperature, under the effect of natural air humidity to give a flexible seal with h...展开 BLUESIL SLT VI 10 is a one component, odourless, ready to use neutral silicone elastomer mainly used as second barrier seal in the Double Glazing market. It cures at room temperature, under the effect of natural air humidity to give a flexible seal with high mechanical performance levels. 收起 | |
| CAB-O-SIL® EH5 | Cabot Corporation - Additives | CAB-O-SIL® EH5 is a very high surface fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and ...展开 CAB-O-SIL® EH5 is a very high surface fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and hyprophilic surface chemistry. This product is well suited for use in adhesives and sealants, coatings, and printing inks. 收起 | |
| CAB-O-SIL® H5 | Cabot Corporation - Additives | CAB-O-SIL® H5 is a high surface area fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and h...展开 CAB-O-SIL® H5 is a high surface area fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and hyprophilic surface chemistry. It is also used for building viscosity in non-polar to medium polarity systems. This product is well suited for use in adhesives, coatings, composites, cosmetics, food, pharmaceuticals, powder coatings, sealants, and silicone rubber systems. 收起 | |
| CAB-O-SIL® LM150 | Cabot Corporation - Additives | CAB-O-SIL® LM150 is a low surface area fumed silica that imparts a moderate increase in viscosity, and reinforcement in liquid and polymer systems. It provides balance of dispersability, thixotropy, and reinforcement. This product is well suited for use f...展开 CAB-O-SIL® LM150 is a low surface area fumed silica that imparts a moderate increase in viscosity, and reinforcement in liquid and polymer systems. It provides balance of dispersability, thixotropy, and reinforcement. This product is well suited for use for thixotropy in silicone sealants and for reinforcement in silicone rubbers. 收起 | |
| CAB-O-SIL® M-5 | Cabot Corporation - Additives | CAB-O-SIL® M-5 is a untreated medium surface fumed silica that provides thickening, thixotrophic, and anti-settling behavior in liquid systems. It is most efficient in non-polar to medium polarity systems, and provides increases in hardness, tensile stren...展开 CAB-O-SIL® M-5 is a untreated medium surface fumed silica that provides thickening, thixotrophic, and anti-settling behavior in liquid systems. It is most efficient in non-polar to medium polarity systems, and provides increases in hardness, tensile strength and elongation. It can be used for reinforcement of silicone and organic rubbers. This product is well suited for use in coatings, adhesives, and other liquid systems. 收起 | |
| CAB-O-SIL® TS530 | Cabot Corporation - Additives | CAB-O-SIL® TS530 is a high-purity silica that has been treated with hexamethyldisilazane to render the silica hydrophobic. It offers good rheological control, sag resistance, anti-settling, and improved dispersion. This product is well suited for use in m...展开 CAB-O-SIL® TS530 is a high-purity silica that has been treated with hexamethyldisilazane to render the silica hydrophobic. It offers good rheological control, sag resistance, anti-settling, and improved dispersion. This product is well suited for use in medium-to-high polarity inks, coatings, and adhesive applications. 收起 | |
| CAB-O-SIL® TS610 | Cabot Corporation - Additives | CAB-O-SIL® TS610 is a low surface area fumed silica that has been surface modified with dimethyldichlorosilane. As a thickener, this product is well suited for use in non-polar to medium polarity inks, coatings, and adhesives. It is also highly effective ...展开 CAB-O-SIL® TS610 is a low surface area fumed silica that has been surface modified with dimethyldichlorosilane. As a thickener, this product is well suited for use in non-polar to medium polarity inks, coatings, and adhesives. It is also highly effective as free-flow additive for moisture-sensitive powder systems. 收起 | |
| CAB-O-SIL® TS622 | Cabot Corporation - Additives | CAB-O-SIL® TS622 is a medium surface area fumed silica that has been surface modified with dimethyldichlorosilane. This product is specially designed for use as a reinforcing agent for RTV-1 silicone sealants, where it provides faster wet-in or incorporat...展开 CAB-O-SIL® TS622 is a medium surface area fumed silica that has been surface modified with dimethyldichlorosilane. This product is specially designed for use as a reinforcing agent for RTV-1 silicone sealants, where it provides faster wet-in or incorporation, better dispersion, and good sealant surface smoothness and appearance. 收起 | |
| CAB-O-SIL® TS720 | Cabot Corporation - Additives | CAB-O-SIL® TS720 is a medium surface area fumed silica which has been surface modified with polydimethylsiloxane. It provides thickening efficiency, sag resistance or high film build, anti-settling of pigments and fillers, shear-thinning rheological behav...展开 CAB-O-SIL® TS720 is a medium surface area fumed silica which has been surface modified with polydimethylsiloxane. It provides thickening efficiency, sag resistance or high film build, anti-settling of pigments and fillers, shear-thinning rheological behavior, and stable rheological performance over time. This product is well suited for rheology control in adhesives, composites, and coatings. 收起 | |
| CAB-O-SPERSE® 1030K | Cabot Corporation - Additives | CAB-O-SPERSE® 1030K is an aqueous fumed silica dispersion featuring low viscosity and high solids loading. Performance benefits of this product include good rheological control,anti-blocking, anti-corrosion, adhesion promotion, and surface treatment prope...展开 CAB-O-SPERSE® 1030K is an aqueous fumed silica dispersion featuring low viscosity and high solids loading. Performance benefits of this product include good rheological control,anti-blocking, anti-corrosion, adhesion promotion, and surface treatment properties. This product is well suited for use in coatings, adhesives, and metal and optical glass polish applications. 收起 | |
| Calcium Sulfate Whisker | Shanghai Tengmin Industry Co., Ltd. | Calcium Sulfate Whisker is a calcium sulfate single crystal that is produced with an advanced environmental technology. This product has smooth texture and stability and is primarily used in sealing materials. | |
| Fumed Silica 972 | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica 972 is a white powdery substance. This product is primarily used as an additive in adhesives, paints, coatings, and printing inks. | |
| Fumed Silica 974 | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica 974 is a white powdery substance. This product is primarily used as an additive in adhesives, paints, coatings, and printing inks. | |
| Fumed Silica (A-150) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-150) is a white and colloidal micro-particle that has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This produc...展开 Fumed Silica (A-150) is a white and colloidal micro-particle that has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, inks, paints and coatings. 收起 | |
| Fumed Silica (A-200) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-200) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluor...展开 Fumed Silica (A-200) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, printing inks, paints, and coatings. 收起 | |
| Fumed Silica (A-380) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-380) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluor...展开 Fumed Silica (A-380) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, printing inks, paints, and coatings. 收起 | |
| Octocure 462 | Tiarco Chemical | Octocure 462 is an aqueous zinc oxide dispersion readily incorporated directly into latex emulsion compounds. It is based on French process zinc oxide. This product is commonly used for pigmenting and vulcanizing SBR and natural latex rubber. | |
| Octocure 487 | Tiarco Chemical | Octocure 487 is an aqueous anionic dispersion of tetramethylthiuram disulfide. It is 50% active and functions as a ready-to-use accelerator for latex compounding. It is commonly used in SBR and natural latex compounds for a sulfurless cure. This product m...展开 Octocure 487 is an aqueous anionic dispersion of tetramethylthiuram disulfide. It is 50% active and functions as a ready-to-use accelerator for latex compounding. It is commonly used in SBR and natural latex compounds for a sulfurless cure. This product may also be used at lower concentrations as a slow precure accelerator in natural latex. 收起 | |
| Octocure 530 | Tiarco Chemical | Octocure 530 is an aqueous anionic dispersion of diphenylguanidine that functions as a ready-to-use accelerator in latex compounding. It is wet milled to a fine particle size for maximum activity. It works in low concentrations as a strong secondary accel...展开 Octocure 530 is an aqueous anionic dispersion of diphenylguanidine that functions as a ready-to-use accelerator in latex compounding. It is wet milled to a fine particle size for maximum activity. It works in low concentrations as a strong secondary accelerator in SBR, neoprene, and nitrile latices. This product is typically used as an activator for MBT and other thiazole accelerators, or in conjunction with dithiocarbamates or thiocarbanilides. 收起 | |
| Octocure 551 | Tiarco Chemical | Octocure 551 is an aqueous anionic dispersion of N,N'-diphenylthiourea. This milled, 50% active thiocarbanalide dispersion is used in neoprene latex, natural rubber latex, and cement applications as a fast-curing accelerator. For neoprene latex, it is usu...展开 Octocure 551 is an aqueous anionic dispersion of N,N'-diphenylthiourea. This milled, 50% active thiocarbanalide dispersion is used in neoprene latex, natural rubber latex, and cement applications as a fast-curing accelerator. For neoprene latex, it is usually used in conjunction with diphenyl guanidine. 收起 | |
| Octocure 573 | Tiarco Chemical | Octocure 573 is an aqueous zinc oxide dispersion that can be readily incorporated directly into latex emulsion compounds. It is based on French process zinc oxide. This product is commonly used for pigmenting and vulcanizing latex rubber. | |
| Octocure 803 | Tiarco Chemical | Octocure 803 is an aqueous zinc oxide dispersion that can be readily incorporated directly into latex emulsion compounds. It is based on French process zinc oxide. This product is commonly used for pigmenting and vulcanizing latex rubber. | |
| Octocure ZBZ-42 | Tiarco Chemical | Octocure ZBZ-42 is an aqueous anionic dispersion of zinc dibenzyldithiocarbamate. It is 42% active and functions as a ready-to-use accelerator for latex compounding. It is typically used in SBR and natural latex compounds in conjunction with secondary acc...展开 Octocure ZBZ-42 is an aqueous anionic dispersion of zinc dibenzyldithiocarbamate. It is 42% active and functions as a ready-to-use accelerator for latex compounding. It is typically used in SBR and natural latex compounds in conjunction with secondary accelerators such as ZMBT. Octocure ZBZ-42 is ideal for vulcanization processes where the formation of volatile nitrosoamines needs to be reduced. 收起 | |
| Octocure ZDB-100 | Tiarco Chemical | Octocure ZDB-100 is a white to off-white powder composed of zinc di-n-butyldithiocarbamate. It functions as a primary accelerator for natural and synthetic polymers. It can be used in most natural rubber compounds for fast cure and high modulus. This prod...展开 Octocure ZDB-100 is a white to off-white powder composed of zinc di-n-butyldithiocarbamate. It functions as a primary accelerator for natural and synthetic polymers. It can be used in most natural rubber compounds for fast cure and high modulus. This product can also be applied in low doses in non-curing natural and SBR adhesive compounds as a non-discoloring antioxidant. 收起 | |
| Octocure ZDB-50 | Tiarco Chemical | Octocure ZDB-50 is an aqueous dispersion of zinc di-n-butyldithiocarbamate. It is 50% active and functions as a ready-to-use accelerator for latex compounding. This product is commonly used in SBR and natural latex compounds for fast cure and high modulus...展开 Octocure ZDB-50 is an aqueous dispersion of zinc di-n-butyldithiocarbamate. It is 50% active and functions as a ready-to-use accelerator for latex compounding. This product is commonly used in SBR and natural latex compounds for fast cure and high modulus. 收起 | |
| Octocure ZDB-50 CF | Tiarco Chemical | Octocure ZDB-50 CF is an aqueous anionic dispersion of zinc di-n-butyldithiocarbamate. Casein free and 50% active, it functions as a ready-to-use accelerator for latex compounding. It is commonly used in SBR and natural latex compounds for fast cure and h...展开 Octocure ZDB-50 CF is an aqueous anionic dispersion of zinc di-n-butyldithiocarbamate. Casein free and 50% active, it functions as a ready-to-use accelerator for latex compounding. It is commonly used in SBR and natural latex compounds for fast cure and high modulus. This product can also be used at low doses in noncuring natural and SBR latex compounds as a non-discoloring antioxidant. 收起 | |
| Octocure ZDE-50 | Tiarco Chemical | Octocure ZDE-50 is an aqueous anionic dispersion of zinc diethyldithiocarbamate. It is 50% active and functions as a ready-to-use accelerator for latex compounding. It is commonly used in SBR and natural latex compounds in conjunction with equal amounts z...展开 Octocure ZDE-50 is an aqueous anionic dispersion of zinc diethyldithiocarbamate. It is 50% active and functions as a ready-to-use accelerator for latex compounding. It is commonly used in SBR and natural latex compounds in conjunction with equal amounts zinc mercaptobenzothiazole. 收起 | |
| Octocure ZDIB-50 | Tiarco Chemical | Octocure ZDIB-50 is an aqueous liquid dispersion of zinc diisobutyldithiocarbamate. It is 50% active and functions as a ready-to-use ultra-accelerator for latex compounding. It is typically used in SBR and natural latex compounds for fast cure and high mo...展开 Octocure ZDIB-50 is an aqueous liquid dispersion of zinc diisobutyldithiocarbamate. It is 50% active and functions as a ready-to-use ultra-accelerator for latex compounding. It is typically used in SBR and natural latex compounds for fast cure and high modulus. As a secondary accelerator, this product works well with thiurams, thiazoles, and guanidines. Octocure ZDIB-50 may be used at low levels to increase cure rates of slower curing systems. It also serves as an effective free-radical emulsion polymerization shortstop in styrene-butadiene rubber (SBR) and acrylonitrile butadiene rubber (NBR) elastomer production. 收起 | |
| Octocure ZDM-50 | Tiarco Chemical | Octocure ZDM-50 is an aqueous anionic dispersion of zinc dimethyldithiocarbamate. It is 50 % active and functions as a ready-to-use accelerator for latex compounding. It provides moderately fast curing with good aging properties. This product is well suit...展开 Octocure ZDM-50 is an aqueous anionic dispersion of zinc dimethyldithiocarbamate. It is 50 % active and functions as a ready-to-use accelerator for latex compounding. It provides moderately fast curing with good aging properties. This product is well suited for use as an additive in the production of latex and latex based products. 收起 | |
| Octocure ZMBT-50 | Tiarco Chemical | Octocure ZMBT-50 is an aqueous anionic dispersion of zinc mercaptobenzothiazole. It is 50% active and functions as a ready-to-use accelerator for latex compounding. It is commonly used as a secondary accelerator in conjunction with a dithiocarbamate. This...展开 Octocure ZMBT-50 is an aqueous anionic dispersion of zinc mercaptobenzothiazole. It is 50% active and functions as a ready-to-use accelerator for latex compounding. It is commonly used as a secondary accelerator in conjunction with a dithiocarbamate. This product is well suited for use as an additive in the production of latex and latex based products. 收起 | |
| Octocure ZMBT-50 CF | Tiarco Chemical | Octocure ZMBT-50 CF is an aqueous anionic dispersion of zinc mercaptobenzothiazole. Casein free and 51% active, it functions as a ready-to-use accelerator for latex compounding. It is commonly used as a secondary accelerator in conjunction with a dithioca...展开 Octocure ZMBT-50 CF is an aqueous anionic dispersion of zinc mercaptobenzothiazole. Casein free and 51% active, it functions as a ready-to-use accelerator for latex compounding. It is commonly used as a secondary accelerator in conjunction with a dithiocarbamate. This product is well suited for use as an additive in the production of latex and latex based products. 收起 | |
| Octoguard FR-11 DF | Tiarco Chemical | Octoguard FR-11 DF is an aqueous anionic dispersion of a halogen and antimony trioxide. It is intended for direct addition to water-based polymer compounds, latex adhesives, binders, coatings, and foams. This product offers high flame retardant effectiven...展开 Octoguard FR-11 DF is an aqueous anionic dispersion of a halogen and antimony trioxide. It is intended for direct addition to water-based polymer compounds, latex adhesives, binders, coatings, and foams. This product offers high flame retardant effectiveness, high purity, excellent heat stability, and low cost. In many cases, it can be used to create environmentally friendly formulations. 收起 | |
| Octoguard FR-13 DF | Tiarco Chemical | Octoguard FR-13 DF is an aqueous anionic dispersion of a halogen and antimony trioxide. It is intended for direct addition to water-based polymer compounds, latex adhesives, binders, coatings, and foams. This product offers high flame retardant effectiven...展开 Octoguard FR-13 DF is an aqueous anionic dispersion of a halogen and antimony trioxide. It is intended for direct addition to water-based polymer compounds, latex adhesives, binders, coatings, and foams. This product offers high flame retardant effectiveness, high purity, excellent heat stability, and low cost. In many cases, it can be used to create environmentally friendly formulations. 收起 | |
| Octolite 424-50 | Tiarco Chemical | Octolite 424-50 is a dispersible aqueous antioxidant emulsion, composed of a synergistic blend of sterically hindered phenol and thioester. It is non-staining, non-discoloring in performance, and provides highly efficient stabilization and antioxidant pro...展开 Octolite 424-50 is a dispersible aqueous antioxidant emulsion, composed of a synergistic blend of sterically hindered phenol and thioester. It is non-staining, non-discoloring in performance, and provides highly efficient stabilization and antioxidant protection in synthetic and natural latex polymers. This product is recommended for use in carboxylated SBR latex compounds and adhesives. 收起 | |
| Octolite 497 | Tiarco Chemical | Octolite 497 is an aqueous antioxidant dispersion composed of butylated hydroxytoluene. It is non-staining, non-discoloring in performance, and provides highly efficient stabilization and antioxidant protection in many polymers against the effects of heat...展开 Octolite 497 is an aqueous antioxidant dispersion composed of butylated hydroxytoluene. It is non-staining, non-discoloring in performance, and provides highly efficient stabilization and antioxidant protection in many polymers against the effects of heat, ultraviolet light, and oxidation. This dispersion is milled to a fine particle size for maximum activity. Octolite 497 is well suited for use in the production of food packaging adhesives and with repeated use rubber products. 收起 | |
| Octolite 544 CF | Tiarco Chemical | Octolite 544 CF is a casein free, 55% concentrated, anionic aqueous dispersion of DNPD antioxidant and metal deactivator (copper inhibitor). This highly active antioxidant is semi-staining and provides good heat and oxidation resistance to SBR, natural, a...展开 Octolite 544 CF is a casein free, 55% concentrated, anionic aqueous dispersion of DNPD antioxidant and metal deactivator (copper inhibitor). This highly active antioxidant is semi-staining and provides good heat and oxidation resistance to SBR, natural, and other latex systems. It is also particularly beneficial in protecting against degradation by trace metals such as copper and manganese. 收起 | |
| Octolite 640 | Tiarco Chemical | Octolite 640 is a dispersible aqueous antioxidant emulsion consisting of a synergistic blend of sterically hindered phenol and thioester. Non-staining and non-discoloring in performance, it provides highly efficient stabilization and antioxidant protectio...展开 Octolite 640 is a dispersible aqueous antioxidant emulsion consisting of a synergistic blend of sterically hindered phenol and thioester. Non-staining and non-discoloring in performance, it provides highly efficient stabilization and antioxidant protection in SBR, natural, and neoprene latex polymers. Octolite 640 is particularly useful for providing superior protection against high-temperature degradation in certain latex polymer compounds. 收起 | |
| Octolite 668 | Tiarco Chemical | Octolite 668 is an anionic aqueous emulsion composed of a highly active, multi-purpose, non-phenolic antioxidant mixture, for all types of latex rubber. It is only slightly staining and virtually non-discoloring. This emulsion is stable over a wide pH ran...展开 Octolite 668 is an anionic aqueous emulsion composed of a highly active, multi-purpose, non-phenolic antioxidant mixture, for all types of latex rubber. It is only slightly staining and virtually non-discoloring. This emulsion is stable over a wide pH range for direct addition to latex. It exhibits low volatility and excellent frothability. Octolite 668 is also highly effective in polychloroprene polymers, providing protection against degradation due to heat, light, and oxygen. 收起 | |
| Octolite 809 | Tiarco Chemical | Octolite 809 is an aqueous anionic dispersion of 2,2'-Methylenebis (4-methyl-6-tert-butylphenol). This primary phenolic antioxidant is effective in preventing thermal oxidation of SBR and natural latex films, adhesives, and foams. This dispersion is ball-...展开 Octolite 809 is an aqueous anionic dispersion of 2,2'-Methylenebis (4-methyl-6-tert-butylphenol). This primary phenolic antioxidant is effective in preventing thermal oxidation of SBR and natural latex films, adhesives, and foams. This dispersion is ball-milled to a fine particle size for maximum activity. Octolite 809 is essentially non-staining but can cause some slight pink discoloration in certain applications. 收起 | |
| Octolite AO-50 | Tiarco Chemical | Octolite AO-50 is a dispersible aqueous emulsion composed of a synergistic blend of sterically hindered phenol and thioester (ditridecylthiodipropionate). This economical, non-staining, non-discoloring antioxidant provides good stabilization and protectio...展开 Octolite AO-50 is a dispersible aqueous emulsion composed of a synergistic blend of sterically hindered phenol and thioester (ditridecylthiodipropionate). This economical, non-staining, non-discoloring antioxidant provides good stabilization and protection to synthetic and natural latex polymers. Octolite AO-50 is ideally suited for use in carboxylated SBR latex compounds and adhesives. 收起 | |
| Octolite WL | Tiarco Chemical | Octolite WL is an aqueous anionic dispersion of sterically hindered phenol. It is non-staining and non-discoloring in performance and provides highly efficient stabilization and antioxidant protection in ABS, synthetic, and natural latex polymers against ...展开 Octolite WL is an aqueous anionic dispersion of sterically hindered phenol. It is non-staining and non-discoloring in performance and provides highly efficient stabilization and antioxidant protection in ABS, synthetic, and natural latex polymers against the effects of heat, ultraviolet light, and oxidation. Octolite WL is well suited for use in the production of food packaging adhesives and with repeated use rubber products. 收起 | |
| Octosol 730 | Tiarco Chemical | Octosol 730 is a surfactant composed of ammonium cocoate in aqueous solution. It can be used as an emulsifier, dispersant, wetting agent, and foaming agent. This product exhibits the excellent frothing and foam stabilizing abilities necessary to produce q...展开 Octosol 730 is a surfactant composed of ammonium cocoate in aqueous solution. It can be used as an emulsifier, dispersant, wetting agent, and foaming agent. This product exhibits the excellent frothing and foam stabilizing abilities necessary to produce quality-frothed adhesives and latex foams. 收起 | |
| Octotint 790 | Tiarco Chemical | Octotint 790 is a water-based dispersion of highly refined brown pigments of extremely fine particle size and purity, with properties tailored for the specific applications of tinting jute adhesives. It can also be used with good compatibility in other aq...展开 Octotint 790 is a water-based dispersion of highly refined brown pigments of extremely fine particle size and purity, with properties tailored for the specific applications of tinting jute adhesives. It can also be used with good compatibility in other aqueous formulations where its characteristic color would be desired. 收起 | |
| Silicon Dioxide GJ-103 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide GJ-103 is a transparent white powder that provides strength and abrasion resistance. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase th...展开 Silicon Dioxide GJ-103 is a transparent white powder that provides strength and abrasion resistance. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
| Silicon Dioxide JLJ-105 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide JLJ-105 is a transparent white powder that has large surface area and small average particle size. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is...展开 Silicon Dioxide JLJ-105 is a transparent white powder that has large surface area and small average particle size. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
| Silicon Dioxide NY-102 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide NY-102 is a white powder that has good dispersion and absorption properties. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bondin...展开 Silicon Dioxide NY-102 is a white powder that has good dispersion and absorption properties. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
| Silicon Dioxide SP-106 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide SP-106 is a transparent white powder that has heavy metal content and strong absorption ability. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is a...展开 Silicon Dioxide SP-106 is a transparent white powder that has heavy metal content and strong absorption ability. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
| Silicon Dioxide TL-104 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide TL-104 is a transparent white powder that is used as a dispersing agent; the liquid form is used as rheology control agent. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase m...展开 Silicon Dioxide TL-104 is a transparent white powder that is used as a dispersing agent; the liquid form is used as rheology control agent. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
| Silicon Dioxide XJ-100 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide XJ-100 is a white powder that is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. | |
| Silicon Dioxide XJ-101 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide XJ-101 is a white powder that is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. | |
| Silicon Dioxide ZZ-108 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide ZZ-108 is a transparent white powder that has high bulkiness and water-solubility properties. This product has the ability to be used as an additive in adhesives to increase mechanical strength, and it is also used in paints and coatings. | |
| SpectrAl® 100 | Cabot Corporation - Additives | SpectrAl® 100 is a high surface area fumed alumina. It has similar properties and functions as fumed silica for rheological control and free flow of powder coats. This product is well suited for use in coatings, adhesives, and rubber products. | |
| SpectrAl® 51 | Cabot Corporation - Additives | SpectrAl® 51 is a low surface area fumed alumina. It has similar morphology and properties as fumed silica for rheological control and free flow. This product is well suited for use in coatings, adhesives, and rubber products. | |
| SpectrAl® 81 | Cabot Corporation - Additives | SpectrAl® 81 is a medium surface area fumed alumina. It has similar morphology and properties as fumed silica for rheological control and free flow. This product is well suited for use in coatings, adhesives, and rubber products. | |
| T-Gum 104 | Tiarco Chemical | T-Gum 104 is a sodium polyacrylate thickener used in a wide variety of natural and synthetic latex applications - including carpet backing, latex foam, adhesives, emulsions, textile coatings, non-wovens, and dispersions. This product may be used to thicke...展开 T-Gum 104 is a sodium polyacrylate thickener used in a wide variety of natural and synthetic latex applications - including carpet backing, latex foam, adhesives, emulsions, textile coatings, non-wovens, and dispersions. This product may be used to thicken styrene-butadiene, acrylonitrile, butadiene, neoprene, acrylic, vinyl acetate, and ethylene-vinyl acetate latex compounds. 收起 |
