| 205 | U.S. Zinc | 205 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, paint/coating, ceramics industries, rubber, and in those applications where reasonable purity is required. 205 is a...展开 205 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, paint/coating, ceramics industries, rubber, and in those applications where reasonable purity is required. 205 is available in a pelleted form (205P) and with surface treatment (205S). It has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| 205H | U.S. Zinc | 205H is a small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the paint, latex, plastic, and zinc chemicals industries and in applications where moderate...展开 205H is a small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the paint, latex, plastic, and zinc chemicals industries and in applications where moderate purity and greater reactivity are required. Grade 205H is available in a pelleted form (205HS) and with surface treatment (205HS). 205H has a surface area range of 6.0 to 8.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| 205HSA | U.S. Zinc | 205HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the plastic, latex, and transparent rubber industries and in those applica...展开 205HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the plastic, latex, and transparent rubber industries and in those applications where great reactivity is required. 205HSA is obtainable with surface treatment (205HSA-S). It has a surface area range of 8.0 to 10.0 m2 /g, a specific gravity of 5.6, and an apparent density of 20 to 40 (pounds/ft3). 收起 | |
| 205L | U.S. Zinc | 205L is a large particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a lower surface area and is used by the paint and ceramics industries and in those applications where benefits result from larger...展开 205L is a large particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a lower surface area and is used by the paint and ceramics industries and in those applications where benefits result from larger than average particles. Grade 205L is available in a pelleted form (205LP) and with surface treatment (205LS). 205L has a surface area range of 3.0 to 5.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| 205XL | U.S. Zinc | 205XL is a large particle size French Process in powder form, statistically measured zinc oxide. 205XL is used by the electronics, coating, ceramics, and paint industries and in those applications which develop benefits from larger than average particles....展开 205XL is a large particle size French Process in powder form, statistically measured zinc oxide. 205XL is used by the electronics, coating, ceramics, and paint industries and in those applications which develop benefits from larger than average particles. It has a surface area range of 2.5 to 3.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 15 to 30. 收起 | |
| 210 | U.S. Zinc | 210 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, rubber, tape/adhesives, oil additives, traffic paint, wire insulation, glass/ceramics, electrogalvanizing, brake li...展开 210 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, rubber, tape/adhesives, oil additives, traffic paint, wire insulation, glass/ceramics, electrogalvanizing, brake lining, and agriculture industries and in applications where General purpose zinc oxide could be used. 210 is available in a pelleted form (210P) and with surface treatment (210S). It has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| 210E | U.S. Zinc | 210E is common purpose French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used in an assortment of applications, including electronics, brake lining, paint, zinc chemicals, coating, and rubber industrie...展开 210E is common purpose French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used in an assortment of applications, including electronics, brake lining, paint, zinc chemicals, coating, and rubber industries. 210E is available in pelleted form (210E-P) and with surface treatment (210ES). It has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| 210H | U.S. Zinc | 210H is a small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the latex, paint, plastic, and zinc chemicals industries. 210H is availab...展开 210H is a small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the latex, paint, plastic, and zinc chemicals industries. 210H is available in a pelleted form (210HP) and with surface treatment (210HS). It has a surface area range of 6.0 to 8.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| 210HSA | U.S. Zinc | 210HSA is an exceptionally small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the plastic, latex, and transparent rubber industries an...展开 210HSA is an exceptionally small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the plastic, latex, and transparent rubber industries and in applications where high reactivity is required. 210HSA is available with surface treatment (210HSA-S). It has a surface area range of 8 to 10 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40. 收起 | |
| 210L | U.S. Zinc | 210L is a large particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a lower surface area and is used by the ceramics and paint industries. 210L is available in a pelleted form (210LP) and with ...展开 210L is a large particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a lower surface area and is used by the ceramics and paint industries. 210L is available in a pelleted form (210LP) and with surface treatment (210LS). It has a surface area range of 3.0 to 5.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| AZO66 | U.S. Zinc | AZO66 is an exceptionally pure French Process, in powder form, statistically measured zinc oxide formed from zinc metal. AZO66 provides greater color and is vastly efficient in white or light colored goods. This grade is used in the zinc chemical, paint/c...展开 AZO66 is an exceptionally pure French Process, in powder form, statistically measured zinc oxide formed from zinc metal. AZO66 provides greater color and is vastly efficient in white or light colored goods. This grade is used in the zinc chemical, paint/coating, ceramic, oil additive industries and in those applications where great purity is dire. Grade AZO66 is available in a pelleted form (AZO66P), in a treated pelleted form (AZO66PT), and with surface treatment (AZO66T). AZO66 has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| AZO66L | U.S. Zinc | AZO66L is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemical, paint, and coating industries and in those applications which stem from greater than norma...展开 AZO66L is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemical, paint, and coating industries and in those applications which stem from greater than normal high purity particles. Grade AZO66L is available in a pelleted form (AZO66LP) and with the surface treatment (AZO66LT). AZO66L has a surface area range of 3.0 to 5.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. 收起 | |
| AZO66XL | U.S. Zinc | AZO66XL is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the electronic, ceramic, paint, and coating industries and in those applications which stem from greater tha...展开 AZO66XL is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the electronic, ceramic, paint, and coating industries and in those applications which stem from greater than normal high purity particles. AZO66XL has a surface area range of 2.5 to 3.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 15 to 30. 收起 | |
| AZO77H | U.S. Zinc | AZO77H is an exceptionally pure powder, small particle size French Process, statistically measured zinc oxide formed from zinc metal. It is used for the manufacture of various chemicals, in the plastic, paint, latex, and coating industries and in those ap...展开 AZO77H is an exceptionally pure powder, small particle size French Process, statistically measured zinc oxide formed from zinc metal. It is used for the manufacture of various chemicals, in the plastic, paint, latex, and coating industries and in those applications where high purity and reactivity is required. Grade AZO77H is available with surface treatment (AZO77HT). It has a surface area range of 6.0 to 8.5 m2 /g, a specific gravity of 5.6, and an apparent density of 20 to 40 (lbs. /cu. Ft.). 收起 | |
| AZO77HSA | U.S. Zinc | AZO77HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. AZO77HSA was explicitly developed to have the highest viscosity, reactivity, purity, and fineness. This grade is used...展开 AZO77HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. AZO77HSA was explicitly developed to have the highest viscosity, reactivity, purity, and fineness. This grade is used in can sealants, latex compounds, zinc chemicals, plastics, paint/coating, and in the food can liner coating industry where the particularly fine particles freely convert certain accessible soluble into white sulfide, thus avoiding discoloration of food from sulfides of tin or iron. AZO77HSA is available with surface treatment (AZO77HSA-T), has a surface area range of 8.0 to 10.0 m2 /g, a specific gravity of 5.6, and an apparent density of 20 to 40 (lbs. /cu. Ft.). 收起 | |
| BLUESIL PRIM 10073 | Elkem Silicones | BLUESIL PRIM 10073 is a product intended to improve the adhesion of BLUESIL one-component and two-component elastomers to metals and certain painted surfaces. The product is available as a ready-to-use solution of reactants diluted in a solvent. | |
| BLUESIL PRIM 12076 | Elkem Silicones | BLUESIL PRIM 12076 is a compound intended to improve the adhesion of one- or two-component room temperature vulcanising silicone elastomers. BLUESIL PRIM 12076 can be used on most porous surfaces. It comes as a colourless, ready to use solution of reactan...展开 BLUESIL PRIM 12076 is a compound intended to improve the adhesion of one- or two-component room temperature vulcanising silicone elastomers. BLUESIL PRIM 12076 can be used on most porous surfaces. It comes as a colourless, ready to use solution of reactants diluted in a solvent. 收起 | |
| BLUESIL RES 8152P | Elkem Silicones | BLUESIL RES 8152P is a 50% solids methylphenylsilicone resin in Toluene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 8170P | Elkem Silicones | BLUESIL RES 8170P is used to manufacture rigid insulators in the high pressure process: laminates based on glass fabric, mica (mica paper), mica/glass composite fabric and asbestos. It offers outstanding mechanical properties. | |
| BLUESIL RES 8360M | Elkem Silicones | BLUESIL RES 8360M is a methyl silicone resin supplied as a solution in toluene and intended for the manufacture of flexible insulants. | |
| BLUESIL SLT 10B OFF WHITE | Elkem Silicones | BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low ...展开 BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. 收起 | |
| BLUESIL SLT 10B PVC WHITE | Elkem Silicones | BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low ...展开 BLUESIL SLT 10B is a one component, odourless, ready-to-use, neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. 收起 | |
| BLUESIL SLT 10T OFF WHITE | Elkem Silicones | BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low m...展开 BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. BLUESIL SLT 10T adheres without a primer on virtually all surfaces found in building construction and accepts movements of 25% in continuous service within a wide range of temperatures. 收起 | |
| BLUESIL SLT 10T PVC WHITE | Elkem Silicones | BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low m...展开 BLUESIL SLT 10T is a one-component, odourless, ready-to-use neutral silicone elastomer (alcoxy type) intended to produce sealing and bonding joints. It cures at room temperature in the presence of air moisture to give a flexible and strong seal with low modulus of elasticity. BLUESIL SLT 10T adheres without a primer on virtually all surfaces found in building construction and accepts movements of 25% in continuous service within a wide range of temperatures. 收起 | |
| BLUESIL SLT 3B BLACK | Elkem Silicones | BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of...展开 BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of 25 % throughout a wide temperature range resistance to severe weathering is excellent. 收起 | |
| BLUESIL SLT 3B TRANSLUCENT | Elkem Silicones | BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of...展开 BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of 25 % throughout a wide temperature range resistance to severe weathering is excellent. 收起 | |
| BLUESIL SLT 3B WHITE | Elkem Silicones | BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of...展开 BLUESIL SLT 3B is a one-component silicone sealant which when exposed to atmospheric humidity, cures rapidly to form a permanently flexible and extremely durable weather tight seal. The cured sealant will accommodate joint movement of maximal amplitude of 25 % throughout a wide temperature range resistance to severe weathering is excellent. 收起 | |
| BLUESIL SLT 3E BLACK | Elkem Silicones | BLUESIL SLT 3E is a one-component silicone sealant which, when exposed to atmospheric humidity, forms a flexible and durable elastomeric seal which possesses excellent resistance to severe weathering conditions. | |
| BLUESIL SLT 3E TRANSLUCENT | Elkem Silicones | BLUESIL SLT 3E is a one-component silicone sealant which, when exposed to atmospheric humidity, forms a flexible and durable elastomeric seal which possesses excellent resistance to severe weathering conditions. | |
| BLUESIL SLT 3E WHITE | Elkem Silicones | BLUESIL SLT 3E is a one-component silicone sealant which, when exposed to atmospheric humidity, forms a flexible and durable elastomeric seal which possesses excellent resistance to severe weathering conditions. | |
| BLUESIL SLT 3S TRANSLUCENT | Elkem Silicones | BLUESIL SLT 3S is a one-component, moisture-cured silicone sealant which contains a fungicide. It cures at room temperature to form a flexible, medium modulus watertight joint for general sanitary sealing. | |
| BLUESIL SLT 3S WHITE | Elkem Silicones | BLUESIL SLT 3S is a one-component, moisture-cured silicone sealant which contains a fungicide. It cures at room temperature to form a flexible, medium modulus watertight joint for general sanitary sealing. | |
| BLUESIL SLT 4S TRANSCLUCENT | Elkem Silicones | BLUESIL SLT 4S is a one-component, moisture-cure silicone sealant which contains a fungicide. It cures at room temperature to form a flexible, low modulus watertight joint for general sanitary sealing. | |
| BLUESIL SLT AQUARIUM BLACK | Elkem Silicones | BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modu...展开 BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modulus of elasticity. BLUESIL SLT AQUARIUM offers excellent resistance to climatic ageing. 收起 | |
| BLUESIL SLT AQUARIUM TRANSLUCENT | Elkem Silicones | BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modu...展开 BLUESIL SLT AQUARIUM is a one-component, ready-to-use silicone elastomer intended for sealing and bonding applications. This sealant cures quickly at room temperature and in the presence of air moisture to give a flexible and strong joint with a high modulus of elasticity. BLUESIL SLT AQUARIUM offers excellent resistance to climatic ageing. 收起 | |
| BLUESIL SLT NOVART S TRANSLUCENT | Elkem Silicones | BLUESIL SLT NOVART S is a one component, neutral (alcoxy) and fast curing, ready-to-use silicone elastomer suitable for weather sealing and bonding seals in construction applications, which is protected by a fungicide. It crosslinks at room temperature to...展开 BLUESIL SLT NOVART S is a one component, neutral (alcoxy) and fast curing, ready-to-use silicone elastomer suitable for weather sealing and bonding seals in construction applications, which is protected by a fungicide. It crosslinks at room temperature to give a flexible seal of low modulus. 收起 | |
| BLUESIL SLT NOVART TRANSLUCENT | Elkem Silicones | BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL ...展开 BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL SLT NOVART can withstand movement of 25 % in constant service throughout a wide temperature range. 收起 | |
| BLUESIL SLT NOVART WHITE | Elkem Silicones | BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL ...展开 BLUESIL SLT NOVART is a one component, neutral and fast curing, ready-to-use silicone elastomer suitable for weather-sealing and bonding seals in construction applications. It crosslinks at room temperature to give a flexible seal of low modulus. BLUESIL SLT NOVART can withstand movement of 25 % in constant service throughout a wide temperature range. 收起 | |
| BLUESIL SLT VEC 90 BLACK | Elkem Silicones | BLUESIL SLT VEC 90 is a one-component silicone elastomer with high mechanical properties mainly intended for applications using so called Structural Glazing technique. It cures at room temperature and in the presence of air humidity to form a strong, fle...展开 BLUESIL SLT VEC 90 is a one-component silicone elastomer with high mechanical properties mainly intended for applications using so called Structural Glazing technique. It cures at room temperature and in the presence of air humidity to form a strong, flexible seal. 收起 | |
| BLUESIL SLT VEC 99A BLACK | Elkem Silicones | BLUESIL SLT VEC 99 is a two-component silicone elastomer with a high modulus of elasticity. After homogeneous mixing of parts A and B, the paste-like product transforms quickly at room temperature into an elastic material with outstanding mechanical and ...展开 BLUESIL SLT VEC 99 is a two-component silicone elastomer with a high modulus of elasticity. After homogeneous mixing of parts A and B, the paste-like product transforms quickly at room temperature into an elastic material with outstanding mechanical and adhesion properties. Its advantage, relative to conventional two-component elastomers lies in the large tolerance relative to the accuracy of the ratio A/B. BLUESIL SLT VEC 99 has been specially designed to meet requirements in Structural Glazing applications. 收起 | |
| BLUESIL SLT VI 10 BLACK | Elkem Silicones | BLUESIL SLT VI 10 is a one component, odourless, ready to use neutral silicone elastomer mainly used as second barrier seal in the Double Glazing market. It cures at room temperature, under the effect of natural air humidity to give a flexible seal with h...展开 BLUESIL SLT VI 10 is a one component, odourless, ready to use neutral silicone elastomer mainly used as second barrier seal in the Double Glazing market. It cures at room temperature, under the effect of natural air humidity to give a flexible seal with high mechanical performance levels. 收起 | |
| Calcium Sulfate Whisker | Shanghai Tengmin Industry Co., Ltd. | Calcium Sulfate Whisker is a calcium sulfate single crystal that is produced with an advanced environmental technology. This product has smooth texture and stability and is primarily used in sealing materials. | |
| DYHARD® 100 | AlzChem | DYHARD® 100 is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomerations...展开 DYHARD® 100 is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomerations and to improve handling. The products of the DYHARD® 100 series do not react with epoxy resins at moderate temperatures. Dispersed in epoxy resin the mixture remains stable until activated by heat. 收起 | |
| DYHARD® 100S | AlzChem | DYHARD® 100S is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomeration...展开 DYHARD® 100S is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomerations and to improve handling. The products of the DYHARD® 100 series do not react with epoxy resins at moderate temperatures. Dispersed in epoxy resin the mixture remains stable until activated by heat. 收起 | |
| DYHARD® 100SF | AlzChem | DYHARD® 100SF is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomeratio...展开 DYHARD® 100SF is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomerations and to improve handling. The products of the DYHARD® 100 series do not react with epoxy resins at moderate temperatures. Dispersed in epoxy resin the mixture remains stable until activated by heat. 收起 | |
| DYHARD® 100SH | AlzChem | DYHARD® 100SH is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomeratio...展开 DYHARD® 100SH is part of a series that consists of different micronized grades of dicyandiamide curing agents for the formulation of thermosetting epoxy resin compositions. They contain up to 3 % of inert anti-caking agent in order to prevent agglomerations and to improve handling. The products of the DYHARD® 100 series do not react with epoxy resins at moderate temperatures. Dispersed in epoxy resin the mixture remains stable until activated by heat. 收起 | |
| DYHARD® A5M30 | AlzChem | DYHARD® A5M30 is widely used as a highly active but also latent accelerator master batch of DYHARD® UR500 in thermosetting epoxy resin formulations. It is especially designed for dust free work environments and easy to mix in productions | |
| DYHARD® CAAB | AlzChem | DYHARD® CAAB is a curing agent for matt finish powder coatings based on epoxy or epoxy-polyester hybrid formulations. Usually it is used together with DYHARD® PIN to realize these matt finishes. For low gloss applications the optimal mixing ratio between ...展开 DYHARD® CAAB is a curing agent for matt finish powder coatings based on epoxy or epoxy-polyester hybrid formulations. Usually it is used together with DYHARD® PIN to realize these matt finishes. For low gloss applications the optimal mixing ratio between DYHARD® PIN and DYHARD® CAAB is 45:55. This ideal mixture is also available in the ready to use premix DYHARD® PMC for an easy handling. 收起 | |
| DYHARD® D50EP | AlzChem | DYHARD® D50EP is a master batch of 50% DYHARD® 100S in standard bisphenol A epoxy resin (EEW 182-192). Advantages include a dust-free production environment, as well as easier dosage and incorporation. It is cost-effective due to easy handling, and offers...展开 DYHARD® D50EP is a master batch of 50% DYHARD® 100S in standard bisphenol A epoxy resin (EEW 182-192). Advantages include a dust-free production environment, as well as easier dosage and incorporation. It is cost-effective due to easy handling, and offers the same reactivity, latency, and mechanical properties as the DYHARD® 100 series. This product is recommended for one-component thermosetting epoxy resin formulations for the automotive, sporting goods, and aerospace industry, for adhesives, for encapsulation compounds, and more. 收起 | |
| DYHARD® DF50EP | AlzChem | DYHARD® DF50EP is a master batch of 50% DYHARD® 100SF in standard bisphenol A epoxy resin (EEW 182-192). Products of the DYHARD® master batches are widely used for all kinds of one component thermosetting epoxy resin formulations | |
| DYHARD® Fluid 111 | AlzChem | DYHARD® Fluid 111 is a liquid latent curing agent for thermosetting epoxy resin formulations. | |
| DYHARD® Fluid 151 | AlzChem | DYHARD® Fluid 151 is part of a fully formulated latent epoxy resin system, which has been specifically designed for resin transfer molding applications. | |
| DYHARD® Fluid 212 | AlzChem | DYHARD® Fluid 212 is a liquid latent curing agent. It features a long pot life in the impregnation bath, a rapid cure at 120ºC, optical clearness, and high transparency. This makes it ideal for use in filament winding applications. | |
| DYHARD® Fluid AC11 | AlzChem | DYHARD® Fluid AC11 is part of a fully formulated latent epoxy resin system, which has been specifically designed for resin transfer molding applications. | |
| DYHARD® MCA10 | AlzChem | DYHARD® MCA10 is a special formulated curing agent for low temperature cure, or very fast cure at standard cure temperatures. A formulated 1K-Epoxy resins system with DYHARD® MCA10 still has an acceptable long latency of a few weeks at room temperature. | |
| DYHARD® MCA30 | AlzChem | DYHARD® MCA30 is a non toxic, special formulated curing agent for low temperature cure, high gloss epoxy powder coatings. | |
| DYHARD® MI-C | AlzChem | DYHARD® MI-C is used as a very active but also reasonably latent accelerator in thermosetting epoxy resin formulations. It is typically used for fast curing, or low temperature cure, resin systems with low latency requirements. | |
| DYHARD® MI-FF | AlzChem | DYHARD® MI-FF is used as a very active but also reasonably latent accelerator in thermosetting epoxy resin formulations. It is typically used for fast curing, or low temperature cure, resin systems with low latency requirements. | |
| DYHARD® MIA5 | AlzChem | DYHARD® MIA5 is used as a very active but also reasonably latent accelerator in thermosetting epoxy resin formulations. It’s use is particularly suited in combination with micronized dicyandiamide from the DYHARD® CU-Line, or with the dicyandiamide master...展开 DYHARD® MIA5 is used as a very active but also reasonably latent accelerator in thermosetting epoxy resin formulations. It’s use is particularly suited in combination with micronized dicyandiamide from the DYHARD® CU-Line, or with the dicyandiamide master batches from the DYHARD® MB-Line. 收起 | |
| DYHARD® OTB | AlzChem | DYHARD® OTB represents a medium reactive curing agent for high gloss epoxy powder coatings. With it’s ideal distribution properties in epoxy resins high quality finishes at low curing temperatures are provided. | |
| DYHARD® PI | AlzChem | DYHARD® PI represents an imidazole based accelerator and/or hardener for thermosetting epoxy resin systems. It has a larger particle size than DYHARD® PI-FF, which is more suitable where lower reactiviy's are needed. | |
| DYHARD® PI-FF | AlzChem | DYHARD® PI-FF represents an imidazole based accelerator and/or hardener for thermosetting epoxy resin systems. DYHARD® PI-FF has a smaller particle size than DYHARD® PI and hence is more suitable where higher reactivity's are needed. | |
| DYHARD® PIN | AlzChem | DYHARD® PIN represents a curing agent which is used in low gloss epoxy and epoxy-polyester hybrid powder coatings. It’s ideal distribution properties in both resin systems provides high quality finishes with a very good color stability. | |
| DYHARD® PMC | AlzChem | DYHARD® PMC represents a matt curing agent for low gloss epoxy and epoxy-polyester hybrid powder coatings. With its ideal distribution properties in both resins systems, high quality finishes with a very good color stability are provided. | |
| DYHARD® RF1000 | AlzChem | DYHARD® RF1000 is part of a fully formulated latent epoxy resin system, which has been specifically designed for resin transfer molding applications. | |
| DYHARD® RF2100 | AlzChem | DYHARD® RF2100 is a low viscos modified bisphenol A epoxy resin. It features a long pot life in the impregnation bath, a rapid cure at 120ºC, optical clearness, and high transparency. This makes it ideal for use in filament winding applications. | |
| DYHARD® UR200 | AlzChem | DYHARD® UR200 represents a latent, micronized accelerator based on a substituted urea. Its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. | |
| DYHARD® UR300 | AlzChem | DYHARD® UR300 represents a latent, micronized accelerator based on a substituted urea. Its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. | |
| DYHARD® UR300AB | AlzChem | DYHARD® UR300AB represents a latent, micronized accelerator based on a substituted urea. Its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. | |
| DYHARD® UR400 | AlzChem | DYHARD® UR400 represents a bi-functional, micronized accelerator based on a substituted urea. Being an active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in...展开 DYHARD® UR400 represents a bi-functional, micronized accelerator based on a substituted urea. Being an active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. 收起 | |
| DYHARD® UR500 | AlzChem | DYHARD® UR500 represents a bi-functional, micronized accelerator based on a substituted urea. Being a highly active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 ser...展开 DYHARD® UR500 represents a bi-functional, micronized accelerator based on a substituted urea. Being a highly active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. 收起 | |
| DYHARD® UR700 | AlzChem | DYHARD® UR700 represents a highly latent, micronized accelerator based on a substituted urea. Its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. In addit...展开 DYHARD® UR700 represents a highly latent, micronized accelerator based on a substituted urea. Its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. In addition, DYHARD® UR700 is soluble in water, which makes it a preferred accelerator for waterborne applications. 收起 | |
| DYHARD® UR800 | AlzChem | DYHARD® UR800 represents a very latent, micronized accelerator based on a substituted urea. Its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. | |
| DYHARD® URAcc13 | AlzChem | DYHARD® URAcc13 represents a formulated latent, micronized accelerator based on a substituted urea. Being an active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 ser...展开 DYHARD® URAcc13 represents a formulated latent, micronized accelerator based on a substituted urea. Being an active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. 收起 | |
| DYHARD® URAcc57 | AlzChem | DYHARD® URAcc57 represents a latent, micronized accelerator based on a substituted urea. Being a very highly active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 ser...展开 DYHARD® URAcc57 represents a latent, micronized accelerator based on a substituted urea. Being a very highly active as well as a latent accelerator, its prominent use is preferably in combination with the highly latent curing agents of the DYHARD® 100 series in thermosetting epoxy resin formulations. 收起 | |
| Fumed Silica 972 | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica 972 is a white powdery substance. This product is primarily used as an additive in adhesives, paints, coatings, and printing inks. | |
| Fumed Silica 974 | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica 974 is a white powdery substance. This product is primarily used as an additive in adhesives, paints, coatings, and printing inks. | |
| Fumed Silica (A-150) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-150) is a white and colloidal micro-particle that has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This produc...展开 Fumed Silica (A-150) is a white and colloidal micro-particle that has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, inks, paints and coatings. 收起 | |
| Fumed Silica (A-200) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-200) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluor...展开 Fumed Silica (A-200) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, printing inks, paints, and coatings. 收起 | |
| Fumed Silica (A-380) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-380) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluor...展开 Fumed Silica (A-380) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, printing inks, paints, and coatings. 收起 | |
| Griltex® 11A | EMS-CHEMIE AG (PRIMID) | Griltex® 11A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a...展开 Griltex® 11A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a laminating temperature of 120-150°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® 1A | EMS-CHEMIE AG (PRIMID) | Griltex® 1A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle size...展开 Griltex® 1A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. It has a lamination temperature of 130-160°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® 2A | EMS-CHEMIE AG (PRIMID) | Griltex® 2A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle size...展开 Griltex® 2A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes. It has a hotmelt application temperature of 180-220°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® 2A S | EMS-CHEMIE AG (PRIMID) | Griltex® 2A S is a copolyamide suspension thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is milky white in appearance, and has a lamination ...展开 Griltex® 2A S is a copolyamide suspension thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is milky white in appearance, and has a lamination temperature of 130-160°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® 6E | EMS-CHEMIE AG (PRIMID) | Griltex® 6E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a ...展开 Griltex® 6E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a hotmelt application temperature of 200-240°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® 8E | EMS-CHEMIE AG (PRIMID) | Griltex® 8E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a ...展开 Griltex® 8E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a laminating temperature of 130-160°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® 9E | EMS-CHEMIE AG (PRIMID) | Griltex® 9E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a ...展开 Griltex® 9E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has a laminating temperature of 120-150°C. This product is well used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® CE 20 | EMS-CHEMIE AG (PRIMID) | Griltex® CE 20 is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle s...展开 Griltex® CE 20 is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. It has a hotmelt application temperature of 180-220°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® CE 21 | EMS-CHEMIE AG (PRIMID) | Griltex® CE 21 is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle s...展开 Griltex® CE 21 is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. It has a hotmelt application temperature of 160-200°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® CE 22 | EMS-CHEMIE AG (PRIMID) | Griltex® CE 22 is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle s...展开 Griltex® CE 22 is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. It has a hotmelt application temperature of 180-220°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® CT 100 | EMS-CHEMIE AG (PRIMID) | Griltex® CT 100 is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle ...展开 Griltex® CT 100 is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. It has a hotmelt application temperature of 180-220°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® CT 101 | EMS-CHEMIE AG (PRIMID) | Griltex® CT 101 is a polyamide 12 thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle...展开 Griltex® CT 101 is a polyamide 12 thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. It has a hotmelt application temperature of 210-250°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® CT 102 | EMS-CHEMIE AG (PRIMID) | Griltex® CT 102 is a polyphenylamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various parti...展开 Griltex® CT 102 is a polyphenylamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes or as suspension. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1260A | EMS-CHEMIE AG (PRIMID) | Griltex® D 1260A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It h...展开 Griltex® D 1260A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in powder form in various particle sizes. It has good steam and dry cleaning resistance. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1299A | EMS-CHEMIE AG (PRIMID) | Griltex® D 1299A is a heat stabilized copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, non-wovens, apparel materials and non-textile substrates. It is available in granule form in various pa...展开 Griltex® D 1299A is a heat stabilized copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, non-wovens, apparel materials and non-textile substrates. It is available in granule form in various particle sizes. It has a hotmelt application temperature of 160-180°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1309E | EMS-CHEMIE AG (PRIMID) | Griltex® D 1309E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle...展开 Griltex® D 1309E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes. It has a hotmelt application temperature of 160-210°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1377E | EMS-CHEMIE AG (PRIMID) | Griltex® D 1377E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle...展开 Griltex® D 1377E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes. It has a lamination temperature of 170-200°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1442E | EMS-CHEMIE AG (PRIMID) | Griltex® D 1442E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle...展开 Griltex® D 1442E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes. It has a hotmelt application temperature of 190-240°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1500A | EMS-CHEMIE AG (PRIMID) | Griltex® D 1500A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle...展开 Griltex® D 1500A is a copolyamide thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule and powder form in various particle sizes. It has a hotmelt application temperature of 150-170°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 | |
| Griltex® D 1519E | EMS-CHEMIE AG (PRIMID) | Griltex® D 1519E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule form in various particle sizes. It ...展开 Griltex® D 1519E is a copolyester thermoplastic, solvent-free adhesive formulated for the coating and laminating of technical textiles, nonwovens, apparel materials and non-textile substrates. It is available in granule form in various particle sizes. It has a hotmelt application temperature of 200-250°C. This product is used in the fields of transportation, construction, electronics, fusible webs and films, medical diagnostics, packaging, composites, and clothing. 收起 |
