Calcium Sulfate Whisker | Shanghai Tengmin Industry Co., Ltd. | Calcium Sulfate Whisker is a calcium sulfate single crystal that is produced with an advanced environmental technology. This product has smooth texture and stability and is primarily used in sealing materials. | |
D.M.P. 30 | Synpol Products PVT. Ltd | D.M.P. 30 is a tertiary amine. This product has a viscosity of 2-5 cPs and a density of 0.9-1.0 g/cm3. D.M.P. 30 is most commonly used as a hardener in lamination and adhesive applications. | |
Epoxy Phenol B.G.E. | Synpol Products PVT. Ltd | Epoxy Phenol B.G.E. is a reactive diluent. This product has a density of 0.92-0.94 g/cm3. Epoxy Phenol B.G.E. is most commonly used in casting, encapsulation, and bonding applications. | |
Epoxy Phenol CNSL | Synpol Products PVT. Ltd | Epoxy Phenol CNSL is a reactive diluent. This product has a density of 0.96-0.97 g/cm3. Epoxy Phenol CNSL is most commonly used in casting, encapsulation, and bonding applications. | |
Epoxy Phenol P.G.E. | Synpol Products PVT. Ltd | Epoxy Phenol P.G.E. is a reactive diluent. This product has a density of 1.11-1.22 g/cm3. Epoxy Phenol P.G.E. is most commonly used in casting, encapsulation, and bonding applications. | |
EXOCOAT™ AM | Axcentive Sarl | EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down v...展开 EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down viruses and bacteria. It eradicates viruses such as influenza, SARS-COV-2, dengue & hepatitis and bacteria such as E. coli, MSRA, streptococcus, listeria, pneumonia, and salmonella. It is activated by light and displays quick drying at room temperature. Spray application is recommended to reach thin monolayers. It exhibits curing at room temperature up to 300°C and super hard particles (1GPa Vickers). It is easy to apply & durable, allowing longer disinfection intervals while preserving hygiene level. It shows non-silver leaching, efficacious even under low light conditions, lower service frequency, and no need for frequent disinfection routine. It is used in the state-of-the-art continuous antimicrobial coating for high-traffic areas. EXOCOAT® AM is suitable for topcoats for any surface inside buildings, stores, hospitals, and vehicles. The shelf life of this product is 9 months. 收起 | |
Fumed Silica 972 | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica 972 is a white powdery substance. This product is primarily used as an additive in adhesives, paints, coatings, and printing inks. | |
Fumed Silica 974 | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica 974 is a white powdery substance. This product is primarily used as an additive in adhesives, paints, coatings, and printing inks. | |
Fumed Silica (A-150) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-150) is a white and colloidal micro-particle that has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This produc...展开 Fumed Silica (A-150) is a white and colloidal micro-particle that has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, inks, paints and coatings. 收起 | |
Fumed Silica (A-200) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-200) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluor...展开 Fumed Silica (A-200) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, printing inks, paints, and coatings. 收起 | |
Fumed Silica (A-380) | Shanghai Tengmin Industry Co., Ltd. | Fumed Silica (A-380) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluor...展开 Fumed Silica (A-380) is a white and colloidal micro-particle with its primary micro-particle from 5-40nm and has properties such as thixotropy, reinforcing, thickening and filling. It is insoluble in all kinds of solvents and liquids except for hydrofluoric acid and concentrated bases. This product is primarily used as an additive in construction sealants, printing inks, paints, and coatings. 收起 | |
Hardeners 111 | Synpol Products PVT. Ltd | Hardeners 111 is an aliphatic polyamine. This product has a viscosity of 15-25 cPs and a density of 0.98-0.99 g/cm3. Hardeners 111 is most commonly used in adhesive and coal tar modified surface coating applications. | |
Hardeners 222 | Synpol Products PVT. Ltd | Hardeners 222 is an aliphatic polyamine. This product has a viscosity of 7-10 cPs and a density of 0.95-0.96 g/cm3. Hardeners 222 is most commonly used in adhesive and coal tar modified surface coating applications. | |
Hardeners 473 | Synpol Products PVT. Ltd | Hardeners 473 is an aliphatic amine adduct. This product has a viscosity of 100-140 cPs and a density of 1.10-1.12 g/cm3. Hardeners 473 is most commonly used in fast-setting adhesive applications. | |
Ketjenflex® 12 | Axcentive Sarl | Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl com...展开 Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl compounds, and PVC based plastisols. It can also be used in PVC based polymers, nitrocellulose resins, and cyanoacrylate adhesives. 收起 | |
Ketjenflex® 6 | Axcentive Sarl | Ketjenflex® 6 is a toluene sulfonamide in the form of a white crystalline powder. It is used as a plasticizer in inks, adhesives, and coatings. Ketjenflex® 6 can be used with resins such as nitrocellulose, polyamide, PVAC, rosin, epoxy, and more. | |
Ketjenflex® 8 | Axcentive Sarl | Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coa...展开 Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coatings, synthetic polyamides, epoxy coatings and adhesives, and more. 收起 | |
Ketjenflex® 9S | Axcentive Sarl | Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wo...展开 Ketjenflex® 9S is a toluene sulfonamide in the form of white crystalline powder. It is used as a reactive plasticizer in coatings and adhesives and provides fungicidal activity in coatings. Ketjenflex® 9S can be used in melamine laminates and coatings, wood adhesives, epoxy and polyurethane coatings and adhesives, and other applications. 收起 | |
Ketjenflex® CP | Axcentive Sarl | Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings. | |
Ketjenflex® MH | Axcentive Sarl | Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printi...展开 Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printing inks. 收起 | |
Ketjenflex® MS 80 | Axcentive Sarl | Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured in...展开 Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured into desired formulations. It has applications in nitrocellulose coatings, cellulose acetate formulations, and printing inks. 收起 | |
Silicon Dioxide GJ-103 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide GJ-103 is a transparent white powder that provides strength and abrasion resistance. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase th...展开 Silicon Dioxide GJ-103 is a transparent white powder that provides strength and abrasion resistance. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
Silicon Dioxide JLJ-105 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide JLJ-105 is a transparent white powder that has large surface area and small average particle size. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is...展开 Silicon Dioxide JLJ-105 is a transparent white powder that has large surface area and small average particle size. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
Silicon Dioxide NY-102 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide NY-102 is a white powder that has good dispersion and absorption properties. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bondin...展开 Silicon Dioxide NY-102 is a white powder that has good dispersion and absorption properties. This product has the ability to be used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
Silicon Dioxide SP-106 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide SP-106 is a transparent white powder that has heavy metal content and strong absorption ability. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is a...展开 Silicon Dioxide SP-106 is a transparent white powder that has heavy metal content and strong absorption ability. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
Silicon Dioxide TL-104 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide TL-104 is a transparent white powder that is used as a dispersing agent; the liquid form is used as rheology control agent. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase m...展开 Silicon Dioxide TL-104 is a transparent white powder that is used as a dispersing agent; the liquid form is used as rheology control agent. This product has the purpose of thickening and anti-settling, and is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. 收起 | |
Silicon Dioxide XJ-100 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide XJ-100 is a white powder that is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. | |
Silicon Dioxide XJ-101 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide XJ-101 is a white powder that is used as an additive in adhesives to increase mechanical strength. It is also used in paints and coatings to increase the bonding properties. | |
Silicon Dioxide ZZ-108 | Shanghai Tengmin Industry Co., Ltd. | Silicon Dioxide ZZ-108 is a transparent white powder that has high bulkiness and water-solubility properties. This product has the ability to be used as an additive in adhesives to increase mechanical strength, and it is also used in paints and coatings. | |
Synpol 140 | Synpol Products PVT. Ltd | Synpol 140 is a reactive polyamide resin. This product has a density at 25°C of 0.96-0.98 g/cm3. Synpol 140 is most commonly used as a hardener in solvent-free coating, adhesive, and lamination applications. | |
Synpol 150 | Synpol Products PVT. Ltd | Synpol 150 is a reactive polyamide resin. This product has a density at 25°C of 0.975-0.985 g/cm3. Synpol 150 is most commonly used as a hardener in solvent-free coating, adhesive, and lamination applications. | |
Synpol 160 | Synpol Products PVT. Ltd | Synpol 160 is a reactive polyamide resin. This product has a density at 25°C of 0.94-0.96 g/cm3. Synpol 160 is most commonly used as a hardener in solvent-free coating, adhesive, and lamination applications. | |
Synpol 200 | Synpol Products PVT. Ltd | Synpol 200 is a bisphenol A-based, unmodified epoxy resin. This product has a viscosity at 25°C of 120-160 Poises. Synpol 200 is most commonly used in coating, lamination, and adhesive applications. | |
Synpol 210 | Synpol Products PVT. Ltd | Synpol 210 is a bisphenol A-based, unmodified reactive diluent. This product has a viscosity at 25°C of 180-210 Poises. Synpol 210 is most commonly used in coating, lamination, and adhesive applications. | |
Synpol 220 | Synpol Products PVT. Ltd | Synpol 220 is a bisphenol A-based, unmodified reactive diluent. This product has a viscosity at 25°C of 180-200 Poises. Synpol 220 is most commonly used in coating, lamination, and adhesive applications. | |
Synpol 230 | Synpol Products PVT. Ltd | Synpol 230 is a bisphenol A-based, unmodified plasticizer. This product has a viscosity at 25°C of 230-250 Poises. Synpol 230 is most commonly used in coating, lamination, and adhesive applications. | |
Synpol 280 | Synpol Products PVT. Ltd | Synpol 280 is a bisphenol A-based, unmodified epoxy resin. This product has a density of 1.18-1.19 g/cm3. Synpol 280 is most commonly used in high-solids coating, adhesive, and lamination applications. | |
Synpol 280 | Synpol Products PVT. Ltd | Synpol 280 is a bisphenol A-based, unmodified plasticizer. This product has a density of 1.22-1.24 g/cm3. Synpol 280 is most commonly used in heat-resistant laminate, electrical casting, adhesive, and coating applications. | |
Synpol 6040 | Synpol Products PVT. Ltd | Synpol 6040 is a soya fatty acid-modified epoxy ester. This product has a density of 0.96-0.97 g/cm3. Synpol 6040 is most commonly used in clear and pigmented electronic and appliance finish applications. | |
Synpol B-30 | Synpol Products PVT. Ltd | Synpol B-30 is a polyvinyl butyral resin in a clear water white-colored, free flowing, granular form. This product has a density at 25°C of 1.05-1.15 g/cm3. Synpol B-30 is most commonly used in metal, textile, paper and foil coating, thermosetting and h...展开 Synpol B-30 is a polyvinyl butyral resin in a clear water white-colored, free flowing, granular form. This product has a density at 25°C of 1.05-1.15 g/cm3. Synpol B-30 is most commonly used in metal, textile, paper and foil coating, thermosetting and hot-melt adhesive, wood finish, and printing ink applications. 收起 | |
Synpol B-60 | Synpol Products PVT. Ltd | Synpol B-60 is a polyvinyl butyral resin in a clear water white-colored, free flowing, granular form. This product has a density at 25°C of 1.05-1.15 g/cm3 and a softening point of 51-55°C. Synpol B-60 is most commonly used in metal, textile, paper and ...展开 Synpol B-60 is a polyvinyl butyral resin in a clear water white-colored, free flowing, granular form. This product has a density at 25°C of 1.05-1.15 g/cm3 and a softening point of 51-55°C. Synpol B-60 is most commonly used in metal, textile, paper and foil coating, thermosetting and hot-melt adhesive, wood finish, and printing ink applications. 收起 | |
Synpol L-9 | Synpol Products PVT. Ltd | Synpol L-9 is a butylated phenolic formaledyde resin. This product has a density of 0.98-0.99 g/cm3 and a total non-volatile content of 58-62%. Synpol L-9 is most commonly used in etch primer, adhesive, insulating varnish, and wire enamel applications. | |
Synpol L-97 | Synpol Products PVT. Ltd | Synpol L-97 is a butylated phenolic formaldehyde resin. This product has a density of 0.98-0.99 g/cm3 and a total non-volatile content of 58-62%. Synpol L-97 is most commonly used in etch primer, adhesive, insulating varnish, and wire enamel applications. | |
Synpol PR-10/B | Synpol Products PVT. Ltd | Synpol PR-10/B is an alkyl phenol formaldehyde thermosetting resin in a pale yellow solid form. This product is most commonly used in spar varnish, marine finish, wood varnish, rubber-based adhesive, and electrical insulating varnish applications. | |
Synpol SK-10 | Synpol Products PVT. Ltd | Synpol SK-10 is a ketone formaldehyde resin. This product has a hydroxyl value of 250-320 mgKOH/g. Synpol SK-10 is most commonly used in NC lacquer, printing ink, and surface coating applications. |