| 99.99% Conductive Shining Flake Silver Powder | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | 99.99% Conductive Shining Flake Silver Powders are different silver powder products are chosen according to different use conditions. Low apparent density flake silver powders is the main raw material in production of conductive coating, membrane switch, ...展开 99.99% Conductive Shining Flake Silver Powders are different silver powder products are chosen according to different use conditions. Low apparent density flake silver powders is the main raw material in production of conductive coating, membrane switch, conductive inks, conductive rubber, conductive plastic, conductive ceramics.Low apparent density flake silver powder is mainly used in the low temperature electronic paste, conductive inks, conductive coatings, electromagnetic shielding coatings. the coating configurated by flake silver powder, whose liquidity and resistance to settlement is good, the coating area is large. 收起 | |
| 99.99% Conductive Silver Powder (Spherical) | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | 99.99% Conductive Silver Powder (Spherical) are widely used in electronic pastes, electronic products, electrical conductivity, electromagnetic shielding, anti-bacterial, and anti-virus applications. | |
| Acetylated Distarch Ddipate | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Acetylated Distarch Ddipate has a certain ability of anti-acid and anti-alkali, anti-cutting ability, is of good viscosity. It is used it as thickening agent, premium quality stabiliser in wallpaper adhesive. | |
| Acetylated Distarch Phosphate | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Acetylated Distarch Phosphate is a fine white to off white powder with characteristic starch taste and odor. Compared with the original starch, the solubility, swelling power and transparency were significantly increased, the aging tendency was significan...展开 Acetylated Distarch Phosphate is a fine white to off white powder with characteristic starch taste and odor. Compared with the original starch, the solubility, swelling power and transparency were significantly increased, the aging tendency was significantly decreased, and the freezing stability was improved. This product is heat-resistant and acid-resistant. It is used it as thickening agent in wallpaper adhesive. 收起 | |
| Alkylsulfonic Acid Ester of Phenol Plasticizer | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Alkylsulfonic acid ester of phenol is a common environmental friendly plasticizer.It possess excellent plasticizing and saponifying effect are suitable for various types of polymers such as PU and PVC. | |
| Cardanol | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Cardanol is made from national cashew nut shell oil, in a high vacuum distillation and solvent extraction processes to obtain industrial cardanol, it can substitute or partial substitute for the production of high performance phenolic resin, epoxy curing ...展开 Cardanol is made from national cashew nut shell oil, in a high vacuum distillation and solvent extraction processes to obtain industrial cardanol, it can substitute or partial substitute for the production of high performance phenolic resin, epoxy curing agents, surfactants, adhesives, paints, and other products used in the manufacture of friction materials epoxy curing agent, liquid phenolic resin, liquid or powdered thermosetting phenolic resin. 收起 | |
| D-101 | BlueSky Chemical Co., Ltd. | D-101, also known as tetramethoxysilane, can be used to provide a scratch-resistant coating and impact modifiers for glass. It can also be used as a drying agent in sealing formulations. | |
| D-31 | BlueSky Chemical Co., Ltd. | D-31 is a blend of methyltris (methylethylketoxime) silane and tetrakis (methylethylketoxime) silane. This product is a cross-linking agent for oxime silicone sealants and is also a liquid raw material for neutral condensation curing silicone sealants. | |
| D-32 | BlueSky Chemical Co., Ltd. | D-32 is a blend of methyltris (methyl ethylketoxime) silane and tetrakis (methyl ethylketoxime) silane. This product is a cross-linking agent for RTV oxime silicone sealants. It is also liquid raw material for neutral condensation curing silicone sealants...展开 D-32 is a blend of methyltris (methyl ethylketoxime) silane and tetrakis (methyl ethylketoxime) silane. This product is a cross-linking agent for RTV oxime silicone sealants. It is also liquid raw material for neutral condensation curing silicone sealants. Its density at 25 degrees Celsius is 0.98 g/ml. 收起 | |
| D-33 | BlueSky Chemical Co., Ltd. | D-33 is a methyltris (methyl ethylketoxime) silane. This product can be used as a cross-linking agent for RTV oxime silicone sealants as well as liquid raw materials for neutral condensation curing silicone sealants. Its density at 25 degrees Celsius is 0...展开 D-33 is a methyltris (methyl ethylketoxime) silane. This product can be used as a cross-linking agent for RTV oxime silicone sealants as well as liquid raw materials for neutral condensation curing silicone sealants. Its density at 25 degrees Celsius is 0.99 g/ml. 收起 | |
| D-34 | BlueSky Chemical Co., Ltd. | D-34 is an oxime silane-based crosslinker, low-ketoxime raw material. This product can be used as a cross-linking agent for RTV oxime silicone sealants as well as a neutral condensation curing silicone sealants. Its density at 25 degrees Celsius is 1.0330...展开 D-34 is an oxime silane-based crosslinker, low-ketoxime raw material. This product can be used as a cross-linking agent for RTV oxime silicone sealants as well as a neutral condensation curing silicone sealants. Its density at 25 degrees Celsius is 1.0330 g/ml. 收起 | |
| D-35 | BlueSky Chemical Co., Ltd. | D-35 is a tetra-oximino silane in toluene. This product is a neutral curing agent for silicone sealant formulations. Its density at 25 degrees Celsius is 0.930 g/ml. | |
| D-36 | BlueSky Chemical Co., Ltd. | D-36 is a phenyltris (methyl ethylketoximino) silane. This product is a cross-linking agent for one-component neutral cure silicone sealants. Its density at 25 degrees Celsius is 0.995 g/ml. | |
| D-60 | BlueSky Chemical Co., Ltd. | D-60 is a di(1,3-propanediol)-bis(ethylacetoacetate) titanium. This product can be used to crosslink and promote adhesion in silicone sealants, adhesives, binders, and paints. Its density at 25 degrees Celsius lies between 1.05 and 1.1 g/ml. | |
| D-70 | BlueSky Chemical Co., Ltd. | D-70 is a dibutyltindiacetate. This product is a catalyst for polyurethane coating and a curing agent for acetoxy sealants. Its density at 25 degrees Celsius is 1.32 g/ml. | |
| D-90 | BlueSky Chemical Co., Ltd. | D-90 is a vinyltris (methylethylketoxime) silane. This product is a neutral curing agent that can be used in silicone sealant formulations. It is usually used in combination with methyloxime silane. This product's density at 25 degrees Celsius is 0.99 g/m...展开 D-90 is a vinyltris (methylethylketoxime) silane. This product is a neutral curing agent that can be used in silicone sealant formulations. It is usually used in combination with methyloxime silane. This product's density at 25 degrees Celsius is 0.99 g/ml. 收起 | |
| D-91 | BlueSky Chemical Co., Ltd. | D-91 is a blend of vinyltris (methyl ethylketoxime) silane and tetrakis (methyl ethylketoxime) silane. This product is a neutral curing agent for silicone sealant formulations. It is usually used in combination with methyloxime silanes. This product's de...展开 D-91 is a blend of vinyltris (methyl ethylketoxime) silane and tetrakis (methyl ethylketoxime) silane. This product is a neutral curing agent for silicone sealant formulations. It is usually used in combination with methyloxime silanes. This product's density at 25 degrees Celsius is 0.99 g/ml. 收起 | |
| D-92 | BlueSky Chemical Co., Ltd. | D-92 is a blend of vinyltris (methyl ethylketoxime) silane and tetrakis (methyl ethylketoxime) silane. This product is a neutral curing agent for silicone sealant formulations. It is used in combination with methyloxime silanes. This product's density ...展开 D-92 is a blend of vinyltris (methyl ethylketoxime) silane and tetrakis (methyl ethylketoxime) silane. This product is a neutral curing agent for silicone sealant formulations. It is used in combination with methyloxime silanes. This product's density at 25 degrees Celsius is 0.99 g/ml. 收起 | |
| Fumed Silica | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Fumed silica is a high value-added fine chemical product; it is a white, loose, amorphous, non-toxic, non-polluting inorganic non-metallic oxide.The primary particle size betweens 7 ~ 40nm and the specific surface area is generally greater than 100m2 / g....展开 Fumed silica is a high value-added fine chemical product; it is a white, loose, amorphous, non-toxic, non-polluting inorganic non-metallic oxide.The primary particle size betweens 7 ~ 40nm and the specific surface area is generally greater than 100m2 / g. Because of its nano-effects, in the material the fumed silica exhibits excellent properties of reinforcing, thickening, thixotropic, insulation, matting, anti-sagging, which are widely used in the silicone rubber (polyester plastics, sealing materials,etc.), siliconeglue (adhesives,paints,coatings,etc.)and high-performance fibers, new synthetic unsaturated resin, electric insulation, inks, pharmaceuticals, paper, food, cosmetics, chemical mechanical polishing, etc., to be known as the "industrial MSG". 收起 | |
| Hydroxypropyl Aistarch Phosphate | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Hydroxypropyl Aistarch Phosphate is a fine white to off white powder with a characteristic odor. This product has good cutting resistance, good acid and alkali resistance, and high viscosity. It is used it as thickening agent in wallpaper adhesive. | |
| LT-151 | BlueSky Chemical Co., Ltd. | LT-151 is a vinyltriethoxysilane. This product can be used as a cross-linking agent and adhesion improver in alkoxy-terminated RTV-1 sealants. Its density at 20 degrees Celsius is 0.905 g/ml. | |
| LT-530 | BlueSky Chemical Co., Ltd. | LT-530 is a 2-(3,4-epoxycyclohexyl) ethyl trimethoxysilane. This product can be used as a water-based polyurethane dispersion in adhesives and as an adhesion promoter for organic/inorganic interfaces. Its density at 25 degrees Celsius is 1.07 g/ml. | |
| LT-540 | BlueSky Chemical Co., Ltd. | LT-540 is a γ-aminopropyltrimethoxysilane and a bifunctional organosilane possessing a reactive primary amine and hydrolysable inorganic methoxysilyl groups. This product can be used as an additive and primer for chemical modification of sealants and adhe...展开 LT-540 is a γ-aminopropyltrimethoxysilane and a bifunctional organosilane possessing a reactive primary amine and hydrolysable inorganic methoxysilyl groups. This product can be used as an additive and primer for chemical modification of sealants and adhesives and in polymers. Its density at 25 degrees Celsius is 1.01 g/ml. 收起 | |
| LT-550 | BlueSky Chemical Co., Ltd. | LT-550 is a γ-aminopropyltriethoxysilane, a bifunctional silane possessing a reactive primary amino group and hydrolyzable ethoxysilyl groups. This product can be used as an adhesion promoter in acrylic coatings, adhesives, and sealants. Its density at 25...展开 LT-550 is a γ-aminopropyltriethoxysilane, a bifunctional silane possessing a reactive primary amino group and hydrolyzable ethoxysilyl groups. This product can be used as an adhesion promoter in acrylic coatings, adhesives, and sealants. Its density at 25 degrees Celsius is 0.94 g/ml. 收起 | |
| LT-560 | BlueSky Chemical Co., Ltd. | LT-560 is a γ-glycidoxypropyltrimethoxysilane, a bifunctional silane possessing a reactive organic epoxide and hydrolysable inorganic methoxysilyl groups. This product can be used as a primer or additive in paints, coatings, sealants and adhesives. Its de...展开 LT-560 is a γ-glycidoxypropyltrimethoxysilane, a bifunctional silane possessing a reactive organic epoxide and hydrolysable inorganic methoxysilyl groups. This product can be used as a primer or additive in paints, coatings, sealants and adhesives. Its density at 25 degrees Celsius is 1.07 g/ml. 收起 | |
| LT-590 | BlueSky Chemical Co., Ltd. | LT-590 is a γ-mercaptopropyl trimethoxysilane, also known as a bifunctional organosilane possessing a reactive organic mercapto and a hydrolysable inorganic methoxysilyl group. This product can be used as a primer or additive in sealants and adhesives. It...展开 LT-590 is a γ-mercaptopropyl trimethoxysilane, also known as a bifunctional organosilane possessing a reactive organic mercapto and a hydrolysable inorganic methoxysilyl group. This product can be used as a primer or additive in sealants and adhesives. Its density at 25 degrees Celsius is 1.057 g/ml. 收起 | |
| LT-602 | BlueSky Chemical Co., Ltd. | LT-602 is an N-(β-aminoethyl)-γ-aminopropylmethyldimethoxysilane. This product can be used as a primer or additive in adhesives and sealants. It can also be used as an adhesion promoter in paints and coatings. Its density at 25 degrees Celsius is 0.98 g/m...展开 LT-602 is an N-(β-aminoethyl)-γ-aminopropylmethyldimethoxysilane. This product can be used as a primer or additive in adhesives and sealants. It can also be used as an adhesion promoter in paints and coatings. Its density at 25 degrees Celsius is 0.98 g/ml. 收起 | |
| LT-792 | BlueSky Chemical Co., Ltd. | LT-792 is a N-(2-aminoethyl)-3-aminopropyltrimethoxysilane. This product can be used as a primer or additive in adhesives and sealants. It can also be used as an adhesion improver in paints and coatings. Its density at 25 degrees Celsius is 1.03 g/ml. | |
| Methyltriethoxysilane | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Methyltriethoxysilane is an industrial grade colorless, transparent liquid. It is used as water repellent to improve fillers dispersibility and reduces their sedimentation tendency. It can also be used as an important component for sol-gel coating, silico...展开 Methyltriethoxysilane is an industrial grade colorless, transparent liquid. It is used as water repellent to improve fillers dispersibility and reduces their sedimentation tendency. It can also be used as an important component for sol-gel coating, silicone resins and silicone rubber,silicone resins and silicone rubber. 收起 | |
| Methyltrimethoxysilane | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Methyltrimethoxysilane is a colorless, low-viscosity liquid, regarded as trifunctional since all three alkoxy groups are able to participate in this reaction. Additionally it contains a methyl group that adds organic character to the products. It is mainl...展开 Methyltrimethoxysilane is a colorless, low-viscosity liquid, regarded as trifunctional since all three alkoxy groups are able to participate in this reaction. Additionally it contains a methyl group that adds organic character to the products. It is mainly used as the crosslinking agent of room temperature vulcanized silicone rubber, as well as the glass fiber surface treatment agent and reinforced plastic laminate treatment agent, in order to improve the mechanical strength of products, heat resistance, moisture resistance. 收起 | |
| Modified Starch - Compound Active Printing Paste | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Modified Starch - Compound Active Printing Paste is the ideal product to replace the sodium alginate in the textile printing industry. This printing paste has not only the advantages of high yield of forming thickening agent, but also good rheological pro...展开 Modified Starch - Compound Active Printing Paste is the ideal product to replace the sodium alginate in the textile printing industry. This printing paste has not only the advantages of high yield of forming thickening agent, but also good rheological properties, thixotropy, holding water capacity, screening, dilution resistance, alkali and salt resistance. It also overcomes the disadvantages of the traditional sodium alginate printing paste in the printing process such as the low color yield and brilliance, bad screening and short retention time of the original paste. The performance/price ratio of this paste is much higher than the sodium alginate and it is the most advanced printing paste products at present. 收起 | |
| Modified Starch - High End | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Modified Starch - High End is ideal product to replace the sodium alginate in the textile printing industry. This printing paste has not only the advantages of high yield of forming thickening agent, but also good rheological properties, thixotropy, holdi...展开 Modified Starch - High End is ideal product to replace the sodium alginate in the textile printing industry. This printing paste has not only the advantages of high yield of forming thickening agent, but also good rheological properties, thixotropy, holding water capacity, screening, dilution resistance, alkali and salt resistance. It also overcomes the disadvantages of the traditional sodium alginate printing paste in the printing process such as the low color yield and brilliance, bad screening and short retention time of the original paste. 收起 | |
| Modified Starch - Mid Range | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Modified Starch - Mid Range is the ideal product to replace the sodium alginate in the textile printing industry. This printing paste has not only the advantages of high yield of forming thickening agent, but also good rheological properties, thixotropy, ...展开 Modified Starch - Mid Range is the ideal product to replace the sodium alginate in the textile printing industry. This printing paste has not only the advantages of high yield of forming thickening agent, but also good rheological properties, thixotropy, holding water capacity, screening, dilution resistance, alkali and salt resistance. It also overcomes the disadvantages of the traditional sodium alginate printing paste in the printing process such as the low color yield and brilliance, bad screening and short retention time of the original paste. The performance/price ratio of this paste is much higher than the sodium alginate and it is the most advanced printing paste products at present. 收起 | |
| Nano Silver Powder TFNP-30 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Nano Silver Powder TFNP-30 is a moderate tap density,high dispersion, spherical nanometer silver powder. TFNP-30 is ideal for low-temperature sintering paste, low silver content and high conductive paste, and touchscreen slurry. | |
| Nano Silver Powder TFNP-80 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Nano Silver Powder TFNP-80 is a moderate tap density, nanoscale spherical monodisperse silver. It is mainly used as an additive material. | |
| ND-22 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | ND-22 is used as cross-linking agent for RTV Silicone Rubber and reinforcing for epoxy fiber glass reinforced plastics, viscosity increaser for synthetic resin and raw stuff fabric racked agent. | |
| Polyvinyl Alcohol | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Polyvinyl alcohol is an important chemical raw materials for the manufacture of polyvinyl acetal, resistance to gasoline pipelines and vinylon synthetic fibers, fabric treatment agents, emulsifiers, paper coatings, adhesives, glues and so on. | |
| Precipitated Silica | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Precipitated silica is a relatively pure form of the mineral silica, which is produced by the chemical process known as precipitation. In chemical precipitation, a solid forms from a liquid due to a chemical reaction. Precipitated silica is formed by mixi...展开 Precipitated silica is a relatively pure form of the mineral silica, which is produced by the chemical process known as precipitation. In chemical precipitation, a solid forms from a liquid due to a chemical reaction. Precipitated silica is formed by mixing solutions of sodium silicate with sulfuric acid in water. A chemical reaction occurs, and pellets of pure silica form. 收起 | |
| PVB | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Polyvinyl butyral (PVB) with hydrochloric acid as catalyst, is made from polyvinyl alcohol and butyl aldehyde. The abbreviate is PVB. High gloss, high transparent, non-toxic, smell-less, fast dissolve, etc. It’s good soluble with pigments and dyes. The PV...展开 Polyvinyl butyral (PVB) with hydrochloric acid as catalyst, is made from polyvinyl alcohol and butyl aldehyde. The abbreviate is PVB. High gloss, high transparent, non-toxic, smell-less, fast dissolve, etc. It’s good soluble with pigments and dyes. The PVB has high transparency, good cold resistance, water resistance, film forming properties and impact resistance, widely used in middle film of glass, ceramic flower paper, metal protective paint, tipping paper, aluminum foil, insulation paint, fiber treatment agent, finished parts, printing inks, dyes and so on. 收起 | |
| PVC Paste | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | PVC Paste is the most widely raw material used in plastic production. It has good chemical stability corrosion resistance and water resistance. It can be dissolved in acetone , hydrochloric ether, ester and some alcohol . It can offer good solubility , go...展开 PVC Paste is the most widely raw material used in plastic production. It has good chemical stability corrosion resistance and water resistance. It can be dissolved in acetone , hydrochloric ether, ester and some alcohol . It can offer good solubility , good electrical insulation , thermoplasticity and membrane forming capacity. They are essential materials for preparing PVC compounds. By adding blending agents and employing different techniques, they can be made into rigid or non-rigid PVC products and are suppliable in a wide range of transparent, translucent, and opaque colours. 收起 | |
| SCA-Y25E | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | SCA-Y25E (3-Isocyanatopropyltriethoxysilane) is unique isocyanate functional silane.The isocyanate functionality exhibits the typical reactivity of an alkyl isocyanate and will react with most reactive hydrogen containing compounds.The silane portion of t...展开 SCA-Y25E (3-Isocyanatopropyltriethoxysilane) is unique isocyanate functional silane.The isocyanate functionality exhibits the typical reactivity of an alkyl isocyanate and will react with most reactive hydrogen containing compounds.The silane portion of these products can then crosslink with each other or be used to adhere to a variety of substrates. SCA-Y25E can be used in a number of applications. 收起 | |
| SCA-Y25M | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | SCA-Y25M (3-Isocyanatopropyltrimethoxysilane) is a unique isocyanate functional silane.The isocyanate functionality exhibits the typical reactivity of an alkyl isocyanate and will react with most reactive hydrogen containing compounds.The silane portion o...展开 SCA-Y25M (3-Isocyanatopropyltrimethoxysilane) is a unique isocyanate functional silane.The isocyanate functionality exhibits the typical reactivity of an alkyl isocyanate and will react with most reactive hydrogen containing compounds.The silane portion of these products can then crosslink with each other or be used to adhere to a variety of substrates. It can be used in a number of applications. 收起 | |
| Silane ATPN-1100 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Silane ATPN-1100 is a versatile amino-functional coupling agent used over a broad range of applications to provide superior bonds between inorganic substrates and organic polymers. The silicon-containing portion of the molecule provides strong bonding to ...展开 Silane ATPN-1100 is a versatile amino-functional coupling agent used over a broad range of applications to provide superior bonds between inorganic substrates and organic polymers. The silicon-containing portion of the molecule provides strong bonding to substrates. The primary amine function reacts with a wide array of thermoset, thermoplastic, and elastomeric materials. 收起 | |
| Silane ATPN-1110 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Silane ATPN-1110 is an amino-functional silane that may be used over a broad range of applications to give an improvement in the bond between a substrate, filler or reinforcement and resins that react with the amino group. It can improve the dispersion an...展开 Silane ATPN-1110 is an amino-functional silane that may be used over a broad range of applications to give an improvement in the bond between a substrate, filler or reinforcement and resins that react with the amino group. It can improve the dispersion and wet ability of filler in the high molecular materials. ATPN-1110 is an excellent promoter of adhesion and sealant (such as polyurethane, epoxy, and phenol). In the glass wool and FRP products, it can be added into phenol resins to improve the wet resistance and mechanical performance. 收起 | |
| Silane ATPN-1120 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Silane ATPN-1120 is a clear, colorless, strongly alkaline liquid with smell being very sensitive to hydrolysis. The chloride content ranges in the lower ppm-level. ATPN-1120 is used as adhesion promoter at organic/inorganic interfaces, for modification of...展开 Silane ATPN-1120 is a clear, colorless, strongly alkaline liquid with smell being very sensitive to hydrolysis. The chloride content ranges in the lower ppm-level. ATPN-1120 is used as adhesion promoter at organic/inorganic interfaces, for modification of surfaces (corrosion prevention, component of primers) or silicone-polymers or as crosslinker (moisture crosslinking of polymers). The application as“coupling agent”leads in general to an improvement of mechanical and electrical product properties above all under exposure to heat and/or moisture. 收起 | |
| Silane ATPN-187 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Silane ATPN-187 is an epoxy-functional silane, it is a clear, light straw liquid. ATPN-187 may used as a coupling agent in polysulfide and polyurethane caulks and sealants, in mineral-filled or glass-reinforced thermosets and thermoplastics, and in glass ...展开 Silane ATPN-187 is an epoxy-functional silane, it is a clear, light straw liquid. ATPN-187 may used as a coupling agent in polysulfide and polyurethane caulks and sealants, in mineral-filled or glass-reinforced thermosets and thermoplastics, and in glass roving size-binders. It is particularly employed as an adhesion-promoting additive in waterborne systems, e.g. improving the adhesion of acrylic latex sealants. 收起 | |
| Silane Coupling Agent Si-69 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Silane Coupling Agent Si-69 is a kind of multifunctional silane coupling agent that has been used successfully in the rubber industry. It is used to improve physical and mechanical properties of vulcanizates. It is able to markedly improve tensile strengt...展开 Silane Coupling Agent Si-69 is a kind of multifunctional silane coupling agent that has been used successfully in the rubber industry. It is used to improve physical and mechanical properties of vulcanizates. It is able to markedly improve tensile strength, tearing strength and abrasive resistance and reduce compression set of vulcanizates. In addition, it can reduce the viscosity and improve the processability of rubber products. Si-69 is especially suitable to improve the reinforcing properties of fillers that contain hydroxyl groups in all unsaturated polymers having double bonds or their blends. 收起 | |
| SILICONE FLUID ATPN-100 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | SILICONE FLUID ATPN-100 is a linear, non-reactive polydimethylsiloxane with a viscosity of approx. 100 mm2 /s. Due to its chemical structure, it has an outstanding property profile, which sets it apart from organic materials such as mineral oils. SILICON...展开 SILICONE FLUID ATPN-100 is a linear, non-reactive polydimethylsiloxane with a viscosity of approx. 100 mm2 /s. Due to its chemical structure, it has an outstanding property profile, which sets it apart from organic materials such as mineral oils. SILICONE FLUID ATPN-100 is ideal for use in a wide range of applications. 收起 | |
| SILICONE FLUID ATPN-1000 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | SILICONE FLUID ATPN-1000 is a linear, non-reactive polydimethylsiloxane with a viscosity of approx. 1 000 mm2/s. Due to its chemical structure, it has an outstanding property profile, which sets it apart from organic materials such as mineral oils. SILICO...展开 SILICONE FLUID ATPN-1000 is a linear, non-reactive polydimethylsiloxane with a viscosity of approx. 1 000 mm2/s. Due to its chemical structure, it has an outstanding property profile, which sets it apart from organic materials such as mineral oils. SILICONE FLUID ATPN-1000 is ideal for use in a wide range of applications. 收起 | |
| Silver Coated Copper Powder | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Silver Coated Copper Powder has Good electrical conductivity, high electrical conductivity and it is not easy to be oxidized, it is a promising good conductive material. It is a good conductive material, it is widely used in the electronic, electromechani...展开 Silver Coated Copper Powder has Good electrical conductivity, high electrical conductivity and it is not easy to be oxidized, it is a promising good conductive material. It is a good conductive material, it is widely used in the electronic, electromechanical, communication, printing, aerospace, etc. 收起 | |
| Speedblock 326 | Lambson Group Ltd. | Speedblock 326 is a UV absorber of the hydroxyl phenyl benzotriazole class and can be used to impart light stability in organic materials and as an adhesive. A pale yellow powder, it contains a range of UV protection with an absorption band width from 220...展开 Speedblock 326 is a UV absorber of the hydroxyl phenyl benzotriazole class and can be used to impart light stability in organic materials and as an adhesive. A pale yellow powder, it contains a range of UV protection with an absorption band width from 220nm to 400nm 收起 | |
| Speedblock 327 | Lambson Group Ltd. | Speedblock 327 is a UV absorber of the hydroxyl phenyl benzotriazole class that has absorption bands in the 200-230nm & 300-360nm ranges. A pale yellow powder, this product can be used in adhesives and polymers. | |
| Speedblock 328 | Lambson Group Ltd. | Speedblock 328 is a UV absorber of the hydroxyl phenyl benzotriazole class that can be used in adhesives and polymers. This pale yellow powder can be used alone or with additional additional additives including hindered light stabilisers antioxidants. | |
| Speedblock AO2 | Lambson Group Ltd. | Speedblock AO2 is a sterically hindered phenolic anti-oxidant. It is an efficient and non-discolouring stabiliser for organic substrates including elastomers and adhesives. A white crystalline powder, it is non-polluting, non-toxic with head and water res...展开 Speedblock AO2 is a sterically hindered phenolic anti-oxidant. It is an efficient and non-discolouring stabiliser for organic substrates including elastomers and adhesives. A white crystalline powder, it is non-polluting, non-toxic with head and water resisting performance while being able to combine with other stabilisers. 收起 | |
| Speedblock UV-0 | Lambson Group Ltd. | SpeedBlock UV-0 is a benzophenone type UV absorber for use in polymer processing, coatings and adhesives. SpeedBlock UV-0 is typically used at 0.1 - 5.0% depending on the substrate, processing conditions and end application. | |
| Speedblock UV-6 | Lambson Group Ltd. | SpeedBlock UV-6 is a highly polymer compatible benzophenone type UV absorber for use in polymer processing, coatings and adhesives. SpeedBlock UV-6 provides low odour and volatility during high temperature processing and is typically used at 0.1 - 5.0% de...展开 SpeedBlock UV-6 is a highly polymer compatible benzophenone type UV absorber for use in polymer processing, coatings and adhesives. SpeedBlock UV-6 provides low odour and volatility during high temperature processing and is typically used at 0.1 - 5.0% depending on the substrate, processing conditions and end application. 收起 | |
| Speedcure 7005 | Lambson Group Ltd. | SpeedCure 7005 is a liquid polymeric Norrish Type II photoinitiator of the benzophenone family, with absorption maxima at 245 and 309 nm. SpeedCure 7005 provides surface cure, low odour and low migration potential when used at 0.5-8 wt% and combined with ...展开 SpeedCure 7005 is a liquid polymeric Norrish Type II photoinitiator of the benzophenone family, with absorption maxima at 245 and 309 nm. SpeedCure 7005 provides surface cure, low odour and low migration potential when used at 0.5-8 wt% and combined with an amine synergist in UV curable formulations. 收起 | |
| Speedcure 7040 | Lambson Group Ltd. | SpeedCure 7040 is a liquid polymeric amine synergist of the aminobenzoate family. SpeedCure 7040 provides low odour, low migration and generates active species when used at 2-10 wt% and combined with Norrish Type II photoinitiators in UV and LED curable f...展开 SpeedCure 7040 is a liquid polymeric amine synergist of the aminobenzoate family. SpeedCure 7040 provides low odour, low migration and generates active species when used at 2-10 wt% and combined with Norrish Type II photoinitiators in UV and LED curable formulations. 收起 | |
| Speedcure 73 | Lambson Group Ltd. | SpeedCure 73 is a liquid Norrish Type I photoinitiator from the hydroxyacetophenone family, with an absorption maximum at 244 nm. SpeedCure 73 provides low yellowing and surface cure when used at 0.5-5 wt% in UV-curable formulations. | |
| Speedcure 84 | Lambson Group Ltd. | SpeedCure 84 is a Norrish Type I photoinitiator from the hydroxyacetophenone family, with an absorption maximum at 244 nm. SpeedCure 84 provides low yellowing and surface cure when used at 0.5-5 wt% in UV curable formulations. | |
| Speedcure 97 | Lambson Group Ltd. | SpeedCure 97 is a Norrish Type I photoinitiator from the aminoacetophenone family, with an absorption maximum at 306 nm. SpeedCure 97 provides high reactivity, surface and depth cure when used at 0.5-5 wt% in UV and LED curable formulations. | |
| Speedcure BDMB | Lambson Group Ltd. | SpeedCure BDMB is a Norrish Type I photoinitiator from the aminoacetophenone family, with an absorption maximumat 321 nm. SpeedCure BDMB provides high reactivity, surface and depth cure when used at 0.5-5 wt% in UV and LED curable formulations. | |
| Speedcure BEDB | Lambson Group Ltd. | SpeedCure BEDB is a liquid amine synergist of the aminobenzoate family. SpeedCure BEDB generates active species when used at 2-8 wt% in combination with Norrish Type II photoinitiators and reduces oxygen inhibition in UV and LED curable formulations. | |
| Speedcure BEM | Lambson Group Ltd. | SpeedCure BEM is a Norrish Type II photoinitiator of the benzophenone family, with an absorption maximum at 254.nm. SpeedCure BEM provides high reactivity and surface cure when used at 0.5-5 wt% and combined with an amine synergist in UV curable formulati...展开 SpeedCure BEM is a Norrish Type II photoinitiator of the benzophenone family, with an absorption maximum at 254.nm. SpeedCure BEM provides high reactivity and surface cure when used at 0.5-5 wt% and combined with an amine synergist in UV curable formulations. 收起 | |
| Speedcure BKL | Lambson Group Ltd. | SpeedCure BKL is a Norrish Type I photoinitiator from the acetophenone family, with an absorption maximum at 253.nm. SpeedCure BKL provides high reactivity and surface cure when used at 0.5-5wt% in UV curable formulations. | |
| Speedcure BMS | Lambson Group Ltd. | SpeedCure BMS is a Norrish Type II photoinitiator of the benzophenone family, with absorption maxima at 246 and 315.nm. SpeedCure BMS provides high reactivity, surface cure and depth cure when used at 0.5-5 wt% and combined with an amine synergist in UV a...展开 SpeedCure BMS is a Norrish Type II photoinitiator of the benzophenone family, with absorption maxima at 246 and 315.nm. SpeedCure BMS provides high reactivity, surface cure and depth cure when used at 0.5-5 wt% and combined with an amine synergist in UV and LED curable formulations. 收起 | |
| Speedcure BP | Lambson Group Ltd. | SpeedCure BP is a Norrish Type II photoinitiator from the benzophenone family, with an absorption maximum at 252 nm. SpeedCure BP provides high reactivity and surface cure when used at 0.5-5 wt% and combined with an amine synergist in UV-curable formulati...展开 SpeedCure BP is a Norrish Type II photoinitiator from the benzophenone family, with an absorption maximum at 252 nm. SpeedCure BP provides high reactivity and surface cure when used at 0.5-5 wt% and combined with an amine synergist in UV-curable formulations. 收起 | |
| Speedcure CPTX | Lambson Group Ltd. | SpeedCure CPTX is a Norrish Type II photoinitiator of the thioxanthone family, with absorption maxima at 257, 314 and 389 nm. SpeedCure CPTX provides long wavelength sensitisation of appropriate photoinitiators and depth cure when used at 0.1-5 wt% and co...展开 SpeedCure CPTX is a Norrish Type II photoinitiator of the thioxanthone family, with absorption maxima at 257, 314 and 389 nm. SpeedCure CPTX provides long wavelength sensitisation of appropriate photoinitiators and depth cure when used at 0.1-5 wt% and combined with an amine synergist in UV and LED curable formulations. 收起 | |
| Speedcure DETX | Lambson Group Ltd. | SpeedCure DETX is a Norrish Type II photoinitiator of the thioxanthone family, with absorption maxima at 261, 291 and 386 nm. SpeedCure DETX provides long wavelength sensitisation of appropriate photoinitiators and depth cure when used at 0.1-5 wt% and co...展开 SpeedCure DETX is a Norrish Type II photoinitiator of the thioxanthone family, with absorption maxima at 261, 291 and 386 nm. SpeedCure DETX provides long wavelength sensitisation of appropriate photoinitiators and depth cure when used at 0.1-5 wt% and combined with an amine synergist in UV and LED curable formulations. 收起 | |
| Speedcure DMB | Lambson Group Ltd. | SpeedCure DMB is an amine synergist of the aliphatic amine family. SpeedCure DMB generates active species when used at 2-8 wt% in combination with Norrish Type II photoinitiators and reduces oxygen inhibition in UV and LED curable formulations. | |
| Speedcure EDB | Lambson Group Ltd. | SpeedCure EDB is an amine synergist of the aminobenzoate family. SpeedCure EDB generates active species when used at 2-8 wt% in combination with Norrish Type II photoinitiators and reduces oxygen inhibition in UV and LED curable formulations. | |
| Speedcure EHA | Lambson Group Ltd. | SpeedCure EHA is a liquid amine synergist of the aminobenzoate family. SpeedCure EHA generates active species when used at 2-8 wt% in combination with Norrish Type II photoinitiators and reduces oxygen inhibition in UV and LED curable formulations. | |
| Speedcure EPD | Lambson Group Ltd. | Speedcure EPD is a highly efficient amine synergist which, when used with Type II photoinitiators, generates free radicals that initiate photo-polymerisation of suitable resin formulations. This white to off white powder has low toxicity and odour in addi...展开 Speedcure EPD is a highly efficient amine synergist which, when used with Type II photoinitiators, generates free radicals that initiate photo-polymerisation of suitable resin formulations. This white to off white powder has low toxicity and odour in addition to solubility in most common organic solvents and UV curable monomers. It is applied to wood varnishes, printing inks, decorative coatings for metal cans and food cartons, adhesives, sealants and metal primers. 收起 | |
| Speedcure MBF | Lambson Group Ltd. | SpeedCure MBF is a liquid Norrish Type II photoinitiator of the benzoylformate family, with an absorption maximum at 244_nm. SpeedCure MBF provides very low yellowing and surface cure when used at 0.5-5 wt% in UV curable formulations. | |
| Speedcure MBP | Lambson Group Ltd. | SpeedCure MBP is a Norrish Type II photoinitiator from the benzophenone family, with absorption maximum at 259.nm. SpeedCure MBP provides high reactivity and surface cure when used at 0.5-5 wt% and combined with an amine synergist in UV curable formulatio...展开 SpeedCure MBP is a Norrish Type II photoinitiator from the benzophenone family, with absorption maximum at 259.nm. SpeedCure MBP provides high reactivity and surface cure when used at 0.5-5 wt% and combined with an amine synergist in UV curable formulations. 收起 | |
| Speedcure PBZ | Lambson Group Ltd. | SpeedCure PBZ is a Norrish Type II photoinitiator of the benzophenone family, with an absorption maximum at 290 nm. SpeedCure PBZ provides high reactivity, surface cure and depth cure when used at 0.5-5 wt% and combined with an amine synergist in UV and L...展开 SpeedCure PBZ is a Norrish Type II photoinitiator of the benzophenone family, with an absorption maximum at 290 nm. SpeedCure PBZ provides high reactivity, surface cure and depth cure when used at 0.5-5 wt% and combined with an amine synergist in UV and LED curable formulations. 收起 | |
| Speedcure PDO | Lambson Group Ltd. | SpeedCure PDO is a Norrish Type I photoinitiator from the oxime ester family, with absorption maximum at 259 nm. SpeedCure PDO provides high reactivity, low yellowing and low volatiles when used at 0.5-5 wt% in UV formulations for electronics applications...展开 SpeedCure PDO is a Norrish Type I photoinitiator from the oxime ester family, with absorption maximum at 259 nm. SpeedCure PDO provides high reactivity, low yellowing and low volatiles when used at 0.5-5 wt% in UV formulations for electronics applications. 收起 | |
| Speedcure XFs | Lambson Group Ltd. | SpeedCure XFs is a blend of difunctional and monofunctional Norrish Type I photoinitiators from the hydroxyacetophenone family, with an absorption maximum at 252 nm. SpeedCure XFs provides low yellowing, surface cure and increased reactivity when used at ...展开 SpeedCure XFs is a blend of difunctional and monofunctional Norrish Type I photoinitiators from the hydroxyacetophenone family, with an absorption maximum at 252 nm. SpeedCure XFs provides low yellowing, surface cure and increased reactivity when used at 0.5-5 wt% in UV curable formulations. 收起 | |
| Sulfolane Anhydrous | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Sulfolane is a colorless and tasteless solid at room temperature, melted at 27.8℃. Most industrial products are colorless and light yellow liquid. Sulfolane has high solubility property and selectivity. It is soluble in water and easily soluble in aromati...展开 Sulfolane is a colorless and tasteless solid at room temperature, melted at 27.8℃. Most industrial products are colorless and light yellow liquid. Sulfolane has high solubility property and selectivity. It is soluble in water and easily soluble in aromatics and alcohol, but has little solubility in paraffin and olefin hydrocarbon. Sulfolane has high stability with hot acid and alkali. It doesn’t react with acid, alkali, sulfur, oralcohol at room temperature, and also doesn’t decompose and polymerize. When the temperature is higher than 240℃, the sulfolane will decompose SO2. Sulfolane has stable chemical property, it will not appear polyreaction and decomposition under common condition with the existence of acid and alkali. 收起 | |
| Sulfolane Aqueous | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | Sulfolane is a colorless and tasteless solid at room temperature, melted at 27.8℃. Most industrial products are colorless and light yellow liquid. Sulfolane has high solubility property and selectivity. It is soluble in water and easily soluble in aromati...展开 Sulfolane is a colorless and tasteless solid at room temperature, melted at 27.8℃. Most industrial products are colorless and light yellow liquid. Sulfolane has high solubility property and selectivity. It is soluble in water and easily soluble in aromatics and alcohol, but has little solubility in paraffin and olefin hydrocarbon. Sulfolane has high stability with hot acid and alkali. It doesn’t react with acid, alkali, sulfur, oralcohol at room temperature, and also doesn’t decompose and polymerize. When the temperature is higher than 240℃, the sulfolane will decompose SO2. Sulfolane has stable chemical property, it will not appear polyreaction and decomposition under common condition with the existence of acid and alkali. 收起 | |
| UVB2000 Special Tertiary Amine Acrylate | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVB2000 Special Tertiary Amine Acrylate is a difunctional amine coinitiator which, when used in conjunction with a photosensitizer such as benzophenone, promotes rapid curing under UV light. Additional benefits include reduced odors, both at press side an...展开 UVB2000 Special Tertiary Amine Acrylate is a difunctional amine coinitiator which, when used in conjunction with a photosensitizer such as benzophenone, promotes rapid curing under UV light. Additional benefits include reduced odors, both at press side and in the cured film, and reduced blooming. It is ideal for use in a wide range of applications. 收起 | |
| UVB2200 Reactive Amine Acrylate | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVB2200 Reactive Amine Acrylate is a very low viscosity, highly reactive amine modified polyetheracrylate oligomer for use in UV and EB curing systems. UVB2200 can be used as the sole binder or with monomer diluents. It is ideal for use in a wide range of...展开 UVB2200 Reactive Amine Acrylate is a very low viscosity, highly reactive amine modified polyetheracrylate oligomer for use in UV and EB curing systems. UVB2200 can be used as the sole binder or with monomer diluents. It is ideal for use in a wide range of applications. 收起 | |
| UVE3216 Modified Epoxy Acrylate | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVE3216 Modified Epoxy Acrylate is a high molecular weight, acid modified epoxy acrylate. It blended with 10% tripropylene glycol diacrylate. It allows high gloss, fast cure response, higher flexibility and low shrikage. UVE3216 is ideal for use in a wide...展开 UVE3216 Modified Epoxy Acrylate is a high molecular weight, acid modified epoxy acrylate. It blended with 10% tripropylene glycol diacrylate. It allows high gloss, fast cure response, higher flexibility and low shrikage. UVE3216 is ideal for use in a wide range of applications. 收起 | |
| Uvi-Cure S105E | Lambson Group Ltd. | UviCure S105E is a high purity, low viscosity difunctional cycloaliphatic epoxide resin which gives clear, hard, glossy coatings when polymerised with onium salt photoinitiators. | |
| Uvi-Cure S110-LV | Lambson Group Ltd. | Uvi-Cure S110-LV is a standard cycloaliphatic epoxy base resin used in metal decoration coatings, overprint varnishes, white base coats, DVD adhesives, electrical coatings and sealants in addition to flexo, screen and ink jet inks. This product contains l...展开 Uvi-Cure S110-LV is a standard cycloaliphatic epoxy base resin used in metal decoration coatings, overprint varnishes, white base coats, DVD adhesives, electrical coatings and sealants in addition to flexo, screen and ink jet inks. This product contains low viscosity enabling a greater scope for meeting end-use processing needs. When this pale yellow to colourless transparent liquid is combined with photoinitiators it produces a clear, hard, glossy coatings. 收起 | |
| Uvi-Cure S128 | Lambson Group Ltd. | UviCure S128 is an adipate based difunctional cycloaliphatic epoxide resin which can be used alone or as an additive in UviCure S105 based formulations to increase the flexibility of a cured coating when polymerised with onium salt photoinitiators. | |
| Uvi-Cure S130 | Lambson Group Ltd. | UviCure S130 is an alcohol functional mono oxetane. It is used as a reactive diluent in cationic formulations and will increase curing speed and adhesion when polymerised with onium salt photoinitiators. | |
| UviCure S105 | Lambson Group Ltd. | UviCure S105 is a low viscosity difunctional cycloaliphatic epoxide resin which gives clear, hard, glossy coatings when polymerised with onium salt photoinitiators. | |
| UVU 6451 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVU 6451 is a tetrafunctional aliphatic urethane acrylate oligomer developed for UV/EB-cured coatings and inks. It imparts hardness, very fast cure response, and non-yellowing characteristics to these applications. | |
| UVU6219 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVU6219 is an aliphatic polyester based urethane diacrylate oligomer blended with 20% TPGDA, tripropylene glycol diacrylate. It is a flexible oligomer offering good weatherability, and low skin irritation. UVU6219 is ideal for use in a wide range of appli...展开 UVU6219 is an aliphatic polyester based urethane diacrylate oligomer blended with 20% TPGDA, tripropylene glycol diacrylate. It is a flexible oligomer offering good weatherability, and low skin irritation. UVU6219 is ideal for use in a wide range of applications. 收起 | |
| UVU6305 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVU6305 is a trifunctional aliphatic polyester urethane acrylate oligomer developed for use in UV and EB cured inks and coatings. Weatherability, low viscosity, and fast cure are among the key attributes of UVU6305. It is ideal for use in a wide range of ...展开 UVU6305 is a trifunctional aliphatic polyester urethane acrylate oligomer developed for use in UV and EB cured inks and coatings. Weatherability, low viscosity, and fast cure are among the key attributes of UVU6305. It is ideal for use in a wide range of applications. 收起 | |
| UVU6609 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVU6609 is a hexafunctional aliphatic urethane acrylate oligomer. It offers low viscosity and good abrasion and heat resistance. UVU6609 is ideal for use in a wide range of applications. | |
| UVU6906 | Beijing Entrepreneur Science &Trading Co., Ltd. 北京安特普纳科贸有限公司 | UVU6906 is a multifunctional urethane acrylate oligomer that imparts chemical resistance, fast cure response, weatherability, and abrasion resistance to radiation-cure coatings. It is ideal for use in a wide range of applications. |
