| BLUESIL ADD 10086 | Elkem Silicones | BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints ...展开 BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints and silicone binders. 收起 | |
| BLUESIL ADD 11013 | Elkem Silicones | BLUESIL ADD 11013 is a polyether-modified polydimethylsiloxane for use in solventless paints and varnishes, and in water-based paints and inks. | |
| BLUESIL BP 9200 | Elkem Silicones | BLUESIL BP 9200 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9300 | Elkem Silicones | BLUESIL BP 9300 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9705 | Elkem Silicones | BLUESIL BP 9705 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL BP 9710 | Elkem Silicones | BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and...展开 BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and it does not contain ecotoxic surfactant. After it has dried on the surface, BLUESIL BP 9710 repels water and allows walls to breathe. Experience acquired over more than 40 years shows that silicone water repellents are a good answer to humidity problems in construction materials, particularly when for esthetical reasons the natural aspect of the material should be preserved. BLUESIL BP 9710 has been awarded a test certificate by CSTC (Centre Scientifique et Technique de - ): ref HD-340/133-151 on the 2006.02.20. 收起 | |
| BLUESIL BP 9800 | Elkem Silicones | BLUESIL BP 9800 is an aqueous APE-free polymethylsiloxane resin emulsion. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9821 | Elkem Silicones | BLUESIL BP 9821 is an aqueous APE-free polymethylsiloxane resin emulsion with low VOC content. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9878 | Elkem Silicones | BLUESIL BP 9878 is an aqueous polymethylsiloxane resin emulsion.This emulsion provides two fundamental properties of the silicone technology to the paint film: water repellency and permeability to water vapour. | |
| BLUESIL BP 9900 | Elkem Silicones | BLUESIL BP 9900 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive for building materials. | |
| BLUESIL BP 9920 | Elkem Silicones | BLUESIL BP 9920is anon-ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL EMUL 1803 | Elkem Silicones | BLUESIL EMUL 1803 is a non-ionic silicone emulsion containing silicone oil and resin. This emulsion is intended for mould-release of cast polyurethane elastomers. | |
| BLUESIL EMUL 269 | Elkem Silicones | BLUESIL EMUL 269 is an aqueous emulsion of an hydrogeno polysiloxane. | |
| BLUESIL EMUL 284 | Elkem Silicones | BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening prop...展开 BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening properties (textile applications). 收起 | |
| BLUESIL EMUL 3500 | Elkem Silicones | BLUESIL EMUL 3500 is a general purpose; non-ionic oil in water silicone emulsion, of a high viscosity hydroxyl terminated polysiloxane. | |
| BLUESIL EMUL 35B | Elkem Silicones | BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream...展开 BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream, neither during storage nor in use.Perfect stability in contact with hard water or zinc (i.e. in galvanized metal containers).Excellent heat stability after dilution.Very good wetting power. 收起 | |
| BLUESIL EMUL 55 | Elkem Silicones | BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component...展开 BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component elements making up polishes and cleaners for artificial leather fabrics (PVC, PUR) and furniture polishes. 收起 | |
| BLUESIL EMUL 872 | Elkem Silicones | BLUESIL EMUL 872 is a slightly anionic aqueous emulsion with a 60% dry content, for general purposes. This is a concentrated version of BLUESIL EMUL E1P. | |
| BLUESIL EMUL E1P | Elkem Silicones | BLUESIL EMUL E1P is an oil in water emulsion containing 35 % of a silicone oil. It can be used in many industries. | |
| BLUESIL EMUL E1P U1 | Elkem Silicones | BLUESIL EMUL E1P U1 is a general purpose, non-ionic, aqueous silicone emulsion. | |
| BLUESIL EMULSION 2400 | Elkem Silicones | BLUESIL EMUL 2400 is a general purpose; non-ionic oil in water silicone emulsion of a methyl-hydrogen polysiloxane. | |
| BLUESIL FLD 21625 | Elkem Silicones | BLUESIL FLD 21625is anα/ω-epoxy functionalised polydimethylsiloxane fluid. | |
| BLUESIL FLD 45 | Elkem Silicones | BLUESIL FLD 45 is a low viscosity dimethylpolysiloxane oil used to prevent floating and flooding and improve leveling of air-drying paints. | |
| BLUESIL FLD 47V1 000 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V100 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V350 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V50 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V500 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL PI 2074 | Elkem Silicones | BLUESIL PI 2074 is a cationic photoinitiator for use with epoxy resins, vinyl ethers or any other type of oligomer which polymerises cationically. It is also suited to the formulation of hybrid radical / cationic systems. | |
| BLUESIL RES 6405 | Elkem Silicones | BLUESIL RES 6405 is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6405X | Elkem Silicones | BLUESIL RES 6405X is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6406XM | Elkem Silicones | BLUESIL RES 6406XM is a 60% solids methylphenylsilicone resin in Xylene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6407 | Elkem Silicones | BLUESIL RES 6407 is a 70% solids methylphenylsilicone resin in Toluene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6482X | Elkem Silicones | BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It i...展开 BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It is also more compatible than other silicones with urea-formaldehyde, melamine-formaldehyde, epoxy, polyurethane and acrylic resins. Another use is as an additive for epoxy paints. It also improves weathering resistance. 收起 | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL SP 3309 | Elkem Silicones | BLUESIL SP 3309 is a polyether modified trisiloxane. | |
| BLUESIL TCS 7001 | Elkem Silicones | BLUESIL TCS 7001 is an alkyl polysiloxane solution in solvent phase specifically developed for the waterproofing of fabrics and leathers exposed to difficult weather conditions by spraying or impregnating. | |
| BURGESS 2211 | Burgess Pigment Company | BURGESS 2211 is a surface modified calcined aluminum silicate that has low warpage and high impact strength. This product is often used in urethane and polyester applications, and can also be used as an extender or filler in paints, coatings, adhesives, a...展开 BURGESS 2211 is a surface modified calcined aluminum silicate that has low warpage and high impact strength. This product is often used in urethane and polyester applications, and can also be used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS 30P® | Burgess Pigment Company | BURGESS 30P® is a flash calcined median particle size clay used extensively in PVC compounds for improving electricals. This product exhibits low specific gravity and excellent color, and can be used as an extender or filler in paints, coatings, adhesives...展开 BURGESS 30P® is a flash calcined median particle size clay used extensively in PVC compounds for improving electricals. This product exhibits low specific gravity and excellent color, and can be used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS 5178 | Burgess Pigment Company | BURGESS 5178 is hydrophobic and a chemical bond between the calcined clay and the polymer exists. This product has been designed to provide excellent wet and dry electrical properties through a proprietary surface treatment. It is often used as an extende...展开 BURGESS 5178 is hydrophobic and a chemical bond between the calcined clay and the polymer exists. This product has been designed to provide excellent wet and dry electrical properties through a proprietary surface treatment. It is often used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS CB | Burgess Pigment Company | BURGESS CB is a surface modified calcined aluminum silicate that has been designed for use in crosslinked polyethylene and polyester. This product can be used as an extender or filler in paints, coatings, adhesives, and sealants. | |
| BURGESS ICEBERG® | Burgess Pigment Company | BURGESS ICEBERG® is a conventionally calcined median particle size, 91-93 GE brightness clay used as an extender of TiO2. It is used in trade sales interior/exterior flat paints and as a filler in polyurethane sealants. This product can provide better opa...展开 BURGESS ICEBERG® is a conventionally calcined median particle size, 91-93 GE brightness clay used as an extender of TiO2. It is used in trade sales interior/exterior flat paints and as a filler in polyurethane sealants. This product can provide better opacity, higher degree of whiteness, better tint strength, easy dispersion, and low moisture levels in moisture sensitive applications. 收起 | |
| BURGESS ICECAP K® | Burgess Pigment Company | BURGESS ICECAP K® is an excellent extender for TiO2 in coatings where a high hegman grind is required. It has good electricals, low compression set, and low water absorption. This product can be used as an extender or filler in paints, coatings, adhesives...展开 BURGESS ICECAP K® is an excellent extender for TiO2 in coatings where a high hegman grind is required. It has good electricals, low compression set, and low water absorption. This product can be used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS ICECAP KSF | Burgess Pigment Company | BURGESS ICECAP KSF is a medium particle size anhydrous (calcined) kaolin clay that is used extensively as a “mild abrasive agent” in various polish applications. This product is a very finely ground dry white powder that exhibits dispersion and extremely ...展开 BURGESS ICECAP KSF is a medium particle size anhydrous (calcined) kaolin clay that is used extensively as a “mild abrasive agent” in various polish applications. This product is a very finely ground dry white powder that exhibits dispersion and extremely low 325 (45 micron) mesh residue. 收起 | |
| BURGESS KE | Burgess Pigment Company | BURGESS KE is an uniquely processed silane modified anhydrous aluminum silicate designed for use in crosslinked polyethylene and polyester systems. This product is a very pure, high brightness, low residue, calcined kaolin that can be used as an extender ...展开 BURGESS KE is an uniquely processed silane modified anhydrous aluminum silicate designed for use in crosslinked polyethylene and polyester systems. This product is a very pure, high brightness, low residue, calcined kaolin that can be used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS NO. 10 | Burgess Pigment Company | BURGESS NO. 10 is a fine particle size, medium brightness hydrous kaolin clay. This product exhibits dispersion in water based, acid pH, alkyd, or solvent based coatings and inks, electrodeposition body primers, as well as EIFS. | |
| BURGESS NO. 17 | Burgess Pigment Company | BURGESS NO. 17 is a fine particle size, high brightness hydrous kaolin clay used to extend TiO2 in semigloss paints and inks. This product is well ground, has excellent whiteness and dispersion, and high brightness. | |
| BURGESS NO. 20 | Burgess Pigment Company | BURGESS NO. 20 is a fine particle size, medium brightness hydrous kaolin clay. This product is used in jacketing layer of wire and cable insulation compounds, rubber roll covers, polishing compounds and concrete curing compounds. It can also be used as an...展开 BURGESS NO. 20 is a fine particle size, medium brightness hydrous kaolin clay. This product is used in jacketing layer of wire and cable insulation compounds, rubber roll covers, polishing compounds and concrete curing compounds. It can also be used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS NO. 27 | Burgess Pigment Company | BURGESS NO. 27 is an ultra fine particle size, medium brightness hydrous kaolin clay. This product is used as an extender in semigloss, satin, and gloss paints. | |
| BURGESS NO. 28 | Burgess Pigment Company | BURGESS NO. 28 is an ultra fine particle size, higher brightness hydrous kaolin clay. This product is used to extend TiO2 while maintaining tint strength and gloss. It is used extensively in water based satin and semigloss coating systems. | |
| BURGESS NO. 30® | Burgess Pigment Company | BURGESS NO. 30® is a partially calcined clay used extensively in PVC compounds to improve insulation resistance. This product exhibits excellent dispersion and color uniformity, and can be used as an extender or filler in paints, coatings, adhesives, and ...展开 BURGESS NO. 30® is a partially calcined clay used extensively in PVC compounds to improve insulation resistance. This product exhibits excellent dispersion and color uniformity, and can be used as an extender or filler in paints, coatings, adhesives, and sealants. 收起 | |
| BURGESS NO. 40 | Burgess Pigment Company | BURGESS NO. 40 is a median particle size, medium brightness hydrous kaolin clay. This product is an acid pH clay exhibiting excellent dispersion properties, and can be used in trade sales coatings and adhesives. | |
| BURGESS NO. 50® | Burgess Pigment Company | BURGESS NO. 50® is a high brightness, fine particle size calcined kaolin that is an extender of TiO2 in coatings or polymeric systems. This product facilitates reduction of prime pigment while maintaining opacity, whiteness, and tint strength of coatings ...展开 BURGESS NO. 50® is a high brightness, fine particle size calcined kaolin that is an extender of TiO2 in coatings or polymeric systems. This product facilitates reduction of prime pigment while maintaining opacity, whiteness, and tint strength of coatings and retention of physical properties in filled polymeric systems. 收起 | |
| BURGESS NO. 60 | Burgess Pigment Company | BURGESS NO. 60 is an acid pH, fine particle size, medium brightness hydrous kaolin clay with excellent dispersion properties. This product is used in inks, adhesives and industrial finishes, electrostatic deposition body primers, and EIFS. | |
| BURGESS NO. 97 | Burgess Pigment Company | BURGESS NO. 97 is an ultra fine particle size, medium brightness hydrous kaolin clay that exhibits excellent tint strength. This product is a well-ground extender of TiO2 in semigloss, satin, and gloss paints. | |
| BURGESS NO. 98 | Burgess Pigment Company | BURGESS NO. 98 is an ultra fine particle size, higher brightness hydrous kaolin clay that exhibits excellent tint strength and dispersion. This product is a well ground, premium extender of TiO2 in water based, solvent or alkyd semigloss, satin, and gloss...展开 BURGESS NO. 98 is an ultra fine particle size, higher brightness hydrous kaolin clay that exhibits excellent tint strength and dispersion. This product is a well ground, premium extender of TiO2 in water based, solvent or alkyd semigloss, satin, and gloss paints. 收起 | |
| BURGESS OPTIPOZZ® | Burgess Pigment Company | BURGESS OPTIPOZZ® is a high reactivity metakaolin produced by a patented process. This product increases chemical resistance and durability, and reduces shrinkage. It can be used as an extender or filler in paints, coatings, adhesives, and sealants. | |
| BURGESS OPTIWHITE® | Burgess Pigment Company | BURGESS OPTIWHITE® is a premium whiteness flash calcined extender for TiO2 exhibiting GE brightness used extensively in First Line interior/exterior flat or low sheen water based and alkyd paint systems. This product exhibits excellent whiteness retention...展开 BURGESS OPTIWHITE® is a premium whiteness flash calcined extender for TiO2 exhibiting GE brightness used extensively in First Line interior/exterior flat or low sheen water based and alkyd paint systems. This product exhibits excellent whiteness retention and hiding when embedded in coatings and polymers. It can provide excellent dispersion, high hiding, and improved film properties. 收起 | |
| BURGESS OPTIWHITE MX® | Burgess Pigment Company | BURGESS OPTIWHITE MX® is a flash calcined clay exhibiting GE Brightness and extension of TiO2, whiteness, touchup, and tint strength. This product is used extensively in flat or low sheen interior/exterior trade sales water-based, alkyd, or solvent-based ...展开 BURGESS OPTIWHITE MX® is a flash calcined clay exhibiting GE Brightness and extension of TiO2, whiteness, touchup, and tint strength. This product is used extensively in flat or low sheen interior/exterior trade sales water-based, alkyd, or solvent-based coatings by reducing the amount of TiO2 and lowering raw material costs while maintaining opacity, whiteness, and tint strength. 收起 | |
| BURGESS OPTIWHITE P® | Burgess Pigment Company | BURGESS OPTIWHITE P® is a flash calcined clay used extensively to extend TiO2. This product exhibits GE Brightness, improves touchup, scrub, and burnish resistance. It is used in flat interior trade sales paints which do not require maximum whiteness. | |
| BURGESS POLYCLAY | Burgess Pigment Company | BURGESS POLYCLAY is a fine particle size, medium brightness hydrous kaolin clay used in inks. | |
| BURGESS THERMOGLACE H | Burgess Pigment Company | BURGESS THERMOGLACE H is a delaminated, fine particle size, medium brightness hydrous kaolin clay. This product is used in primers and trade sales coatings for the reduction of mud-cracking (micro-cracking due to film stress) and reduction of permeability...展开 BURGESS THERMOGLACE H is a delaminated, fine particle size, medium brightness hydrous kaolin clay. This product is used in primers and trade sales coatings for the reduction of mud-cracking (micro-cracking due to film stress) and reduction of permeability. 收起 | |
| CAF 2534 | Elkem Silicones | CAF 2534 is a one component silicone rubber that cures when in contact with air humidity. It is intended for use as a formulation base for the development of tie-coats in the fouling release treatment of boat hulls. | |
| JMT-150ANO | Tayca Corporation | JMT-150ANO is a cationic titanium dioxide with an average primary particle size of 15 nm. It is surface treated with alkylsilane, making it suitable for use as a water repellant colorant in paints, inks and electrophotography. | |
| JMT-150AO | Tayca Corporation | JMT-150AO is an anionic titanium dioxide with an average primary particle size of 15 nm. It is surface treated with alkylsilane, making it suitable for use as a water repellant colorant in paints, inks and electrophotography. | |
| JMT-150FI | Tayca Corporation | JMT-150FI is an anionic titanium dioxide with an average primary particle size of 15 nm. It is surface treated with alkylsilane, making it suitable for use as a water repellant colorant in paints, inks and electrophotography. | |
| JMT-150IB | Tayca Corporation | JMT-150IB is an anionic titanium dioxide with an average primary particle size of 15 nm. It is surface treated with alkylsilane, making it suitable for use as a water repellant colorant in paints, inks and electrophotography. | |
| JR-301 | Tayca Corporation | JR-301 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .3µm particle...展开 JR-301 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .3µm particle size and 18 g/100g of oil absorption. 收起 | |
| JR-403 | Tayca Corporation | JR-403 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average ....展开 JR-403 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .25µm particle size and 19 g/100g of oil absorption. 收起 | |
| JR-405 | Tayca Corporation | JR-405 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .21µm particl...展开 JR-405 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .21µm particle size and 15 g/100g of oil absorption. 收起 | |
| JR-600A | Tayca Corporation | JR-600A is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .25µm partic...展开 JR-600A is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .25µm particle size and 19 g/100g of oil absorption. 收起 | |
| JR-600E | Tayca Corporation | JR-600E is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .27µm partic...展开 JR-600E is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .27µm particle size and 21 g/100g of oil absorption. 收起 | |
| JR-603 | Tayca Corporation | JR-603 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum and zirconium with an average...展开 JR-603 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum and zirconium with an average .28µm particle size and 21 g/100g of oil absorption. 收起 | |
| JR-605 | Tayca Corporation | JR-605 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .25µm particl...展开 JR-605 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum with an average .25µm particle size and 19 g/100g of oil absorption. 收起 | |
| JR-701 | Tayca Corporation | JR-701 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum, silicone and zinc with an av...展开 JR-701 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum, silicone and zinc with an average .27µm particle size and 20 g/100g of oil absorption. 收起 | |
| JR-800 | Tayca Corporation | JR-800 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for inks that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .27...展开 JR-800 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for inks that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .27µm particle size and 29 g/100g of oil absorption. 收起 | |
| JR-805 | Tayca Corporation | JR-805 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for inks that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .29...展开 JR-805 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for inks that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .29µm particle size and 22 g/100g of oil absorption. 收起 | |
| JR-806 | Tayca Corporation | JR-806 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for inks that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .25...展开 JR-806 is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for inks that are applied to automobiles, household products and other white-colored products. It contains aluminum and silicon with an average .25µm particle size and 21 g/100g of oil absorption. 收起 | |
| JRNC | Tayca Corporation | JRNC is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum, silicone and zinc with an aver...展开 JRNC is a rutile crystal structured white pigment used as a coloring agent. This titanium dioxide is used for paints that are applied to automobiles, household products and other white-colored products. It contains aluminum, silicone and zinc with an average .27µm particle size and 21 g/100g of oil absorption. 收起 | |
| K-White #105 | Tayca Corporation | K-White #105 is a white powder aluminum triphosphate with an average particle size of 1.6 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent...展开 K-White #105 is a white powder aluminum triphosphate with an average particle size of 1.6 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #140W | Tayca Corporation | K-White #140W is a white powder aluminum triphosphate with an average particle size of 2.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solven...展开 K-White #140W is a white powder aluminum triphosphate with an average particle size of 2.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #450H | Tayca Corporation | K-White #450H is a white powder aluminum triphosphate with an average particle size of 3.5 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solven...展开 K-White #450H is a white powder aluminum triphosphate with an average particle size of 3.5 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #82 | Tayca Corporation | K-White #82 is a white powder aluminum triphosphate with an average particle size of 3.5 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent-...展开 K-White #82 is a white powder aluminum triphosphate with an average particle size of 3.5 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #84 | Tayca Corporation | K-White #84 is a white powder aluminum triphosphate with an average particle size of 3.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent-...展开 K-White #84 is a white powder aluminum triphosphate with an average particle size of 3.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #84S | Tayca Corporation | K-White #84S is a white powder aluminum triphosphate with an average particle size of 3.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent...展开 K-White #84S is a white powder aluminum triphosphate with an average particle size of 3.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #85 | Tayca Corporation | K-White #85 is a white powder aluminum triphosphate with an average particle size of 3.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent-...展开 K-White #85 is a white powder aluminum triphosphate with an average particle size of 3.7 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White #94 | Tayca Corporation | K-White #94 is a white powder aluminum triphosphate with an average particle size of 6.3 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent-...展开 K-White #94 is a white powder aluminum triphosphate with an average particle size of 6.3 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White Ca650 | Tayca Corporation | K-White Ca650 is a white powder aluminum triphosphate with an average particle size of 3.5 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solven...展开 K-White Ca650 is a white powder aluminum triphosphate with an average particle size of 3.5 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| K-White G105 | Tayca Corporation | K-White G105 is a white powder aluminum triphosphate with an average particle size of 2.3 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent...展开 K-White G105 is a white powder aluminum triphosphate with an average particle size of 2.3 microns. It is designed to be used as an anti-corrosive, white pigment in a wide range of fields such as paints, coatings and inks. It can be used with both solvent- and water-based applications. 收起 | |
| LYNDCOAT 15 RTU | Elkem Silicones | LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RT...展开 LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RTU also helps keep molds and vents clean, reducing defects and downtime. Lyndcoat™ 15 RTU typically is durable through multiple production cycles. The need for reapplication is dependent on factors such as the rubber compound, curing time, curing temperature, tread design and application technique. Lyndcoat™ 15 RTU is designed for processes requiring low viscosity mold lubricants. 收起 | |
| LYNDCOAT BR 1100 RTU | Elkem Silicones | LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the c...展开 LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1100 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1100 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as Lyndcoat™ BR2101 RTU is highly recommended. 收起 | |
| LYNDCOAT BR 1102 | Elkem Silicones | LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the c...展开 LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1102 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1102 RTU is of medium viscosity and does not contain mica. 收起 | |
| LYNDCOAT BR 1103 RTU | Elkem Silicones | LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the c...展开 LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR1103 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. LYNDCOAT® BR1103 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as LYNDCOAT® BR2201 RTU is highly recommended. 收起 | |
| LYNDCOAT BR 1110 RTU | Elkem Silicones | LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers ...展开 LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. LYNDCOAT BR 1110 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. LYNDCOAT BR 1110 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as LYNDCOAT BR 2101 RTU, is highly recommended. 收起 | |
| LYNDCOAT BR 1211 | Elkem Silicones | LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtim...展开 LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtimes. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. 收起 |
