| Acronal® 296 D ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 阴离子乳液聚合物，粘度中等。它含有细小、良好分散的颗粒。它与颜填料具有出色的相容性。对颜料具有非常高的粘合力。未着色的Acronal®296 D apare涂膜透明、柔韧、高光泽，具有极高的耐水性和非常好的耐皂化性能 | |
| Acronal® 296 DS ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 高品质、通用型建筑涂料用乳液聚合物。Acronal® 296 DS ap是一种阴离子型低粘度的乳液聚合物，它由细小的微粒组成。与颜填料有出色的兼容性，具备超强的颜料粘结力。Acronal® 296 DS ap乳液膜在室温下不粘手。Acronal® 296 DS ap乳液膜透明，柔软且有光泽，具有极好的耐水性，且具备出色的耐皂化特性。 | |
| Acronal® 7016 G | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 一种阴离子型中等粘度的乳液聚合物。它由细小的微粒组成，是一种拥有优异户外耐久性和耐沾污性的纯丙烯酸共聚物。能使涂膜拥有良好的耐擦洗性、抗粘连性、对混凝土表面有良好的附着力。 | |
| Acronal® 7026 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 良好分散的的聚合物乳液，粘度低。该乳液形成的涂膜在很宽的温度范围内具有高弹性，尤其是在寒冷气候环境下。与填料和颜料具有出色的相容性。它具有非常高的颜料粘合力。用Acronal®7026形成的涂膜具有出色的耐水、耐碱性能和耐风化性能。Acronal®7026配制的弹性墙面涂料具有良好的耐毛细裂纹，由于采用了紫外表面交联技术，即使在温暖高污染的环境下也具有非常好的耐玷污性能 | |
| Acronal® 7035 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 耐擦洗性能优异的高PVC内墙涂料用乳液聚合物 Acronal®7035是不含APEO的低粘度阴离子乳液.它由细小的乳液粒子组成. Acronal®7035具有很高的对颜填料的粘结力，因此它即使在很高PVC时仍然 使得涂料具有突出的耐擦洗性 | |
| Acronal® 7035 G | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 耐擦洗性能优异的高PVC内墙涂料用乳液聚合物。Acronal®7035G是不含APEO的低粘度阴离子乳液.它由细小的乳液粒子组成。Acronal®7035G具有很高的对颜填料的粘结力，因此它即使在很高PVC时仍然使得涂料具有突出的耐擦洗性 | |
| Acronal® 7037 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 具有极佳耐擦洗性多功能内墙建筑涂料用乳液聚合物,Acronal® 7037是一种不含APEO的低黏度阴离子乳液聚合物。它由细小的乳液粒子组成。Acronal® 7037 具有很高的对颜填料的粘结力，因此它即使在很高PVC时仍然使得涂料具有突出的耐擦洗性。 | |
| Acronal® 7051 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 适用于真石漆和质感涂料的水性聚合物乳液 Acronal®7051是一种具有中等黏度的细微分散乳液聚合物。它是一种与常用颜料及骨料具有良好相容性的纯丙烯酸乳液，同时其具有优异的钙离子稳定性。其涂膜坚韧，具有柔性及抗粘连性。Acronal® 7051形成的膜具高耐水性、耐光性，优异的抗皂化性及耐候性。即使在水中长时间浸泡，涂膜也不会水白。 | |
| Acronal® A 684 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 通用型，具有出色的附着力和出色的耐候性 | |
| Acronal® DS 6266 ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 可广泛用于各种乳胶漆和质感面漆的聚合物乳液 Acronal®DS 6266 ap 是一种中等粘度的阴离子型聚合物乳液。它拥有极细的 粒径，能形成无色、透明滑爽的涂膜。产品性能优异，具有良好的抗发白性、低吸水性和高耐候性。 | |
| Acronal® ECO 338 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种细粒径，低黏度的水性乳液。无气味，而且不包含氨水，溶剂及增塑剂。它与常用的颜料与填料展现优异的相容性。形成的涂膜透明，柔性且有光泽，并具备好的耐水性及耐水解性。 | |
| Acronal® ECO 502 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是低黏度，细小乳胶，无气味，不含氨水及任何溶剂或增塑剂，拥有出色的颜料相容性和粘结能力，而且配方内不需要助成膜助剂。其干膜透明，有光泽和弹性，并有很好的耐水和抗水解性能。 | |
| Acronal® ECO 612 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 全丙烯酸共聚物，用于低光泽建筑涂料。用Acronal®ECO 612 ap形成的涂料能在保持VOC含量接近零的条件下满足严苛性能。由于其出色的附着力和抗粘连性能，Acronal®ECO 612 ap配制的涂料非常适合各种表面类型和应用。另外，Acronal®ECO 612 ap表现出优秀的耐常规家庭污染物的能力 | |
| Acronal® ECO 702 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种阴离子型中等黏度，细小粒径的水性乳胶。拥有优异的颜料和填料的相容性与粘结性能。Acronal ECO 702 ap 在无颜填料时形成的膜透明，有弹性和光泽，并具有出色的耐水和抗皂化性能。 | |
| Acronal® ECO 9056 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 阴离子乳液聚合物，具有中等粘度。它含有细小良好分散的颗粒。它与颜料和填料具有出色的相容性。它具有非常高的颜料粘合力。未着色的Acronal®ECO 9056涂膜可在室温下指干。Acronal®ECO 9056的涂膜透明、柔韧和高光，具有极高的耐水性和非常好的耐皂化性能 | |
| Acronal® Flex SC 138 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 良好分散的聚合物乳液，粘度低。与填料和颜料具有出色的相容性。它具有非常高的颜料粘合力。用Acronal®FLEX SC 138形成的涂膜具有出色的耐水、耐碱性能和耐候性。Acronal®FLEX SC 138配制的弹性墙面涂料即使在温暖高污染的环境下也具有良好的耐毛细裂纹以及非常好的耐玷污性能 | |
| Acronal® GS 409 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种低粘度细小粒径聚合物乳液。它与填料和颜料具有优异的相容性，同时具有极高的颜料粘结力。由Acronal GS 409 ap形成的漆膜具有优异的耐水性、耐碱性和耐候性。采用Acronal GS 409 ap配制的弹性涂料能能够提供毛细裂纹的桥接，即使在温暖和污染的环境中，也具有非常出色的耐沾污性。 | |
| Acronal® JC 7043 X | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种拥有细小粒径和低粘度的阴离子R-C乳液。它是一 种长链的丙烯酸和苯乙烯共聚物，具备优异的对粉化基材的渗透性和优异的耐碱性，适用于水性渗透性和耐碱性底漆，该底漆可替代溶剂型体系。该产品对粉化砖石基材具有优异的粘结力。 Acronal® JC 7043 适用于制备全效合一水性底漆产品。 | |
| Acronal® PA 510 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种阴离子型的分散介质的粘度。该乳液具有非常细的颗粒，提供优良的增稠响应。 ACRONAL®PA510配方的高光泽涂料耐高挡。 ACRONAL®PA510具有优异的湿附着力对木材和任何关键基材，尤其是老化醇酸的基材. | |
| Acronal® PA 807 ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 乳液聚合物，耐久、低粘灰，用于高品质户外乳胶漆。Acronal® PA 807 ap是一种阴离子乳液聚合物，粘度中等，含有细小、良好分散的颗粒。它是一种全丙烯酸共聚物具有出色的户外耐久性和良好的耐玷污性能。该聚合物制备的涂膜具有良好的耐擦洗性能，防粘连性能，良好的对圬工表面的附着力以及特别好的湿遮盖力。Acronal® PA 807 ap适合用于制备各种应用的油漆，可配制不同光泽水平。 | |
| Acronal® PS 791 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 乳液聚合物，用于高品质通用型建筑涂料，Acronal® PS 791 ap是一种阴离子乳液聚合物，粘度低，含有细小、良好分散的颗粒。它具有与颜填料出色的相容性和非常高的颜料粘合力。未着色的Acronal® PS 791 ap涂膜可在室温下指干。Acronal® PS 791 ap形成的涂膜透明、柔韧、光泽高，具有极高的耐水性，和非常好的耐皂化性能 | |
| DA-100 | DCC (Dairen Chemical Corp.) | DA-100 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-100 forms a flexible film with adhesive properties for broad applications. DA-100 is used as a base emu...展开 DA-100 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-100 forms a flexible film with adhesive properties for broad applications. DA-100 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-100 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-117 | DCC (Dairen Chemical Corp.) | DA-117 is a non-plasticized, aqueous, milky, white dispersion of a vinyl acetate-ethylene copolymer with high solid contents developed to provide a versatile base for construction applications. After evaporation of its water content, DA-117 forms a flexib...展开 DA-117 is a non-plasticized, aqueous, milky, white dispersion of a vinyl acetate-ethylene copolymer with high solid contents developed to provide a versatile base for construction applications. After evaporation of its water content, DA-117 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 500-1500 mPa.s. DA-117 is used in joint compounds and decorative coatings, and carpet back coatings. 收起 | |
| DA-1210 | DCC (Dairen Chemical Corp.) | DA-1210 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1210 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1210 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1210 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1210 is used in construction adhesives, sealing slurries, and repair mortars. 收起 | |
| DA-125 | DCC (Dairen Chemical Corp.) | DA-125 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -8 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-125 is used as general adhesive f...展开 DA-125 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -8 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-125 is used as general adhesive for packaging, bookbinding, and bonding for plastic films, coated papers. DA-125 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-125 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-128 | DCC (Dairen Chemical Corp.) | DA-128 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13°C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128 is used as general adhesive f...展开 DA-128 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13°C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128 is used as general adhesive for packaging, bookbinding, and bonding for plastic films, coated papers. DA-128 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-128 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-128H | DCC (Dairen Chemical Corp.) | DA-128H is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128H is used as general adhesiv...展开 DA-128H is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128H is used as general adhesive for packaging, bookbinding, and bonding for plastic films, coated papers. DA-128H is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-128H is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-1410 | DCC (Dairen Chemical Corp.) | DA-1410 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1410 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1410 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1410 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1410 is used in construction adhesives. 收起 | |
| DA-1420 | DCC (Dairen Chemical Corp.) | DA-1420 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1420 improves adhesion, flexural strength, plasticity, abrasion resistance, and workability of modified compound...展开 DA-1420 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1420 improves adhesion, flexural strength, plasticity, abrasion resistance, and workability of modified compounds. DA-1420 is used in tile adhesives. 收起 | |
| DA-1430 | DCC (Dairen Chemical Corp.) | DA-1430 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1430 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. D...展开 DA-1430 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1430 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. DA-1430 is used in tile adhesives, and trowelling compounds. 收起 | |
| DA-1450 | DCC (Dairen Chemical Corp.) | DA-1450 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1450 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. D...展开 DA-1450 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1450 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. DA-1450 is used in tile adhesives, and construction adhesives. 收起 | |
| DA-183 | DCC (Dairen Chemical Corp.) | DA-183 is a vinyl acetate-ethylene copolymer emulsion for cement or plaster based mortars. The addition causes of DA-183 increases the adhesion of mortars to other mineral surfaces. These modified coatings show much better elasticity. DA-183 is used in mo...展开 DA-183 is a vinyl acetate-ethylene copolymer emulsion for cement or plaster based mortars. The addition causes of DA-183 increases the adhesion of mortars to other mineral surfaces. These modified coatings show much better elasticity. DA-183 is used in mortars or grouts. 收起 | |
| DA-265H | DCC (Dairen Chemical Corp.) | DA-265H is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene-acrylate terpolymer emulsion with a solid content of 65%. A water-resistant, clear and flexible film is formed after drying. This film exhibits stability against degradation, disco...展开 DA-265H is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene-acrylate terpolymer emulsion with a solid content of 65%. A water-resistant, clear and flexible film is formed after drying. This film exhibits stability against degradation, discoloration, oxygen, and the ozone. Because of DA-265H's adjusted ethylene content, this film is extremely tacky and uses no plasticizers to get softness or flexibility. DA-265H is used in mineral coatings, and floor, wall, or ceiling adhesives. 收起 | |
| DA-3510 | DCC (Dairen Chemical Corp.) | DA-3510 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. This resin is soft and flexible, because of its relatively high ethylene content. DA-3510 enhances the adhesion, fle...展开 DA-3510 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. This resin is soft and flexible, because of its relatively high ethylene content. DA-3510 enhances the adhesion, flexural strength, plasticity, and workability of modified compounds. DA-3510 is recommended for use as a sole binder for making construction adhesives and seals. 收起 | |
| DA-371 | DCC (Dairen Chemical Corp.) | DA-371 is an aqueous, non-plasticized, milky white emulsion synthesized from vinyl acetate and ethylene. DA-371 with different paint formulations can bring about many changes of the gloss of indoor-paints in accordance with the customers’ demand. DA-371 i...展开 DA-371 is an aqueous, non-plasticized, milky white emulsion synthesized from vinyl acetate and ethylene. DA-371 with different paint formulations can bring about many changes of the gloss of indoor-paints in accordance with the customers’ demand. DA-371 is used in low VOC interior paints, semi flat and semi gloss paints, deep shade paints, exterior paints, and plaster and textured coatings. 收起 | |
| DA-500 | DCC (Dairen Chemical Corp.) | DA-500 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-500 forms a flexible film with adhesive properties for a broad range of applications. DA-500 is used in...展开 DA-500 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-500 forms a flexible film with adhesive properties for a broad range of applications. DA-500 is used in base for EPI wood glue systems, as a base emulsion for floor, wall or ceiling adhesives, and plastic (PVC) or metal foil bonding. 收起 | |
| DA-502 | DCC (Dairen Chemical Corp.) | DA-502 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-502 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosit...展开 DA-502 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-502 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosity at 25 °C of 3000-4000 mPa.s. DA-502 is used in base for EPI wood glue systems, as a base emulsion for floor, wall or ceiling adhesives, and plastic (PVC) or metal foil bonding. 收起 | |
| DA-511 | DCC (Dairen Chemical Corp.) | DA-511 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-511 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosit...展开 DA-511 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-511 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosity at 25 °C of 1500-2500 mPa.s. DA-511 is used in base for EPI wood glue systems, as a base emulsion for floor, wall or ceiling adhesives, and plastic (PVC) or metal foil bonding. 收起 | |
| DA-523 | DCC (Dairen Chemical Corp.) | DA-523 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-523 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosit...展开 DA-523 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-523 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosity at 25 °C of 700-1000 mPa.s. DA-523 is used in base for EPI wood glue systems, as a base emulsion for floor, wall or ceiling adhesives, and plastic (PVC) or metal foil bonding. 收起 | |
| DA-524 | DCC (Dairen Chemical Corp.) | DA-524 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-524 forms a tough but still flexible film with adhesive properties for a broad range of applications. I...展开 DA-524 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-524 forms a tough but still flexible film with adhesive properties for a broad range of applications. It has a viscosity at 25 °C of 1500-2500 mPa.s. DA-524 is used in base for EPI wood glue systems, as a base emulsion for floor, wall or ceiling adhesives, and plastic (PVC) or metal foil bonding. 收起 | |
| DA-652 | DCC (Dairen Chemical Corp.) | DA-652 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, the extra viscous DA-652 forms a flexible film with adhesive properties for a broad range of applications....展开 DA-652 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, the extra viscous DA-652 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosity at 25 °C of 15000-25000 mPa.s. DA-652 is used as base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| Laromer® PO 94 F | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 胺改性聚醚丙烯酸酯，适用于辐射固化油墨以及木材，木制品，纸张和塑料辐射固化涂料配方。反应速度非常快，具有非常好的耐化学品性。 | |
| Picassian® AC-126 | Stahl Polymers | Picassian® AC-126 is a waterbased, anionic, styrene-acrylic copolymer emulsion agent that is used as an anticorrosive primer on concrete flooring, sport floors, roofing porous tiles as well as being used as an universal decorative primers. It provides glo...展开 Picassian® AC-126 is a waterbased, anionic, styrene-acrylic copolymer emulsion agent that is used as an anticorrosive primer on concrete flooring, sport floors, roofing porous tiles as well as being used as an universal decorative primers. It provides glossy, hard, and transparent films once coalesced. This product has good water resistance, humidity resistance, adhesion, corrosion resistance, blister resistance, and mechanical properties. It also has good compatibility with other binders such as acrylics and polyurethanes. 收起 | |
| Picassian® AC-169 | Stahl Polymers | Picassian® AC-169 is a waterbased anionic self crosslinking stryene acrylic copolymer emulsion agent. It is used in furniture coatings, wood floor primers, and sanding sealers. This product has good blocking resistance properties, good scratch resistance ...展开 Picassian® AC-169 is a waterbased anionic self crosslinking stryene acrylic copolymer emulsion agent. It is used in furniture coatings, wood floor primers, and sanding sealers. This product has good blocking resistance properties, good scratch resistance properties, good clarity properties, and is quick and easy to sand. 收起 | |
| Relca® HY-460 | Stahl Polymers | Relca® HY-460 is an aqueous anionic dispersion of an alkyd modified aliphatic urethane. It is used in decorative applications, interior DTM applications, exterior DTM applications, interior wood coatings, and exterior wood coating applications. This produ...展开 Relca® HY-460 is an aqueous anionic dispersion of an alkyd modified aliphatic urethane. It is used in decorative applications, interior DTM applications, exterior DTM applications, interior wood coatings, and exterior wood coating applications. This product has fast drying properties, good adhesion properties, good shear stability properties, good pigment wetting properties, and is solvent free. 收起 | |
| Relca® HY-625 | Stahl Polymers | Relca® HY-625 is an aqueous anionic dispersion of an aliphatic polyester urethane. It is used in wood and parquet flooring, furniture coatings, and wood coatings. This product is solvent free, has good Taber abrasion resistance properties, good water resi...展开 Relca® HY-625 is an aqueous anionic dispersion of an aliphatic polyester urethane. It is used in wood and parquet flooring, furniture coatings, and wood coatings. This product is solvent free, has good Taber abrasion resistance properties, good water resistance properties, good hydrolysis resistance properties, high hardness properties, and good adhesion properties with wood. 收起 | |
| Relca® PU-476 | Stahl Polymers | Relca® PU-476 is an aqueous anionic dispersion of an alkyd modified aliphatic urethane. It is used in interior DTM applications, wood coatings, and parquet flooring. This product is solvent free, has good open time properties, high hardness properties, go...展开 Relca® PU-476 is an aqueous anionic dispersion of an alkyd modified aliphatic urethane. It is used in interior DTM applications, wood coatings, and parquet flooring. This product is solvent free, has good open time properties, high hardness properties, good adhesion properties, good chemical resistance properties, good pigment wetting properties, good scratch resistance properties, and good black heel mar resistance properties. 收起 | |
| Relca® PU-655 | Stahl Polymers | Relca PU-655 is an aqueous, anionic dispersion of an aliphatic polycarbonate urethane. It is used in parquet flooring, wood coatings, and metal pre-treatment. This product is solvent free, has good water resistance properties, good chemical resistance pro...展开 Relca PU-655 is an aqueous, anionic dispersion of an aliphatic polycarbonate urethane. It is used in parquet flooring, wood coatings, and metal pre-treatment. This product is solvent free, has good water resistance properties, good chemical resistance properties, good hydrolysis resistance properties, and good adhesion properties with metal and wood. 收起 | |
| Versamine® 911 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 中等粘度，固化快的改性胺类环氧固化剂。它用于防表面泛白，同时具有良好柔韧性的体系。推荐用于无溶剂涂料，装饰涂料及快速固化地坪和复合材料的修补。 |
