| Acronal® 296 D ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 阴离子乳液聚合物，粘度中等。它含有细小、良好分散的颗粒。它与颜填料具有出色的相容性。对颜料具有非常高的粘合力。未着色的Acronal®296 D apare涂膜透明、柔韧、高光泽，具有极高的耐水性和非常好的耐皂化性能 | |
| Acronal® 296 DS ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 高品质、通用型建筑涂料用乳液聚合物。Acronal® 296 DS ap是一种阴离子型低粘度的乳液聚合物，它由细小的微粒组成。与颜填料有出色的兼容性，具备超强的颜料粘结力。Acronal® 296 DS ap乳液膜在室温下不粘手。Acronal® 296 DS ap乳液膜透明，柔软且有光泽，具有极好的耐水性，且具备出色的耐皂化特性。 | |
| Acronal® 7016 G | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 一种阴离子型中等粘度的乳液聚合物。它由细小的微粒组成，是一种拥有优异户外耐久性和耐沾污性的纯丙烯酸共聚物。能使涂膜拥有良好的耐擦洗性、抗粘连性、对混凝土表面有良好的附着力。 | |
| Acronal® 7026 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 良好分散的的聚合物乳液，粘度低。该乳液形成的涂膜在很宽的温度范围内具有高弹性，尤其是在寒冷气候环境下。与填料和颜料具有出色的相容性。它具有非常高的颜料粘合力。用Acronal®7026形成的涂膜具有出色的耐水、耐碱性能和耐风化性能。Acronal®7026配制的弹性墙面涂料具有良好的耐毛细裂纹，由于采用了紫外表面交联技术，即使在温暖高污染的环境下也具有非常好的耐玷污性能 | |
| Acronal® 7035 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 耐擦洗性能优异的高PVC内墙涂料用乳液聚合物 Acronal®7035是不含APEO的低粘度阴离子乳液.它由细小的乳液粒子组成. Acronal®7035具有很高的对颜填料的粘结力，因此它即使在很高PVC时仍然 使得涂料具有突出的耐擦洗性 | |
| Acronal® 7035 G | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 耐擦洗性能优异的高PVC内墙涂料用乳液聚合物。Acronal®7035G是不含APEO的低粘度阴离子乳液.它由细小的乳液粒子组成。Acronal®7035G具有很高的对颜填料的粘结力，因此它即使在很高PVC时仍然使得涂料具有突出的耐擦洗性 | |
| Acronal® 7037 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 具有极佳耐擦洗性多功能内墙建筑涂料用乳液聚合物,Acronal® 7037是一种不含APEO的低黏度阴离子乳液聚合物。它由细小的乳液粒子组成。Acronal® 7037 具有很高的对颜填料的粘结力，因此它即使在很高PVC时仍然使得涂料具有突出的耐擦洗性。 | |
| Acronal® 7051 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 适用于真石漆和质感涂料的水性聚合物乳液 Acronal®7051是一种具有中等黏度的细微分散乳液聚合物。它是一种与常用颜料及骨料具有良好相容性的纯丙烯酸乳液，同时其具有优异的钙离子稳定性。其涂膜坚韧，具有柔性及抗粘连性。Acronal® 7051形成的膜具高耐水性、耐光性，优异的抗皂化性及耐候性。即使在水中长时间浸泡，涂膜也不会水白。 | |
| Acronal® A 684 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 通用型，具有出色的附着力和出色的耐候性 | |
| Acronal® DS 6266 ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 可广泛用于各种乳胶漆和质感面漆的聚合物乳液 Acronal®DS 6266 ap 是一种中等粘度的阴离子型聚合物乳液。它拥有极细的 粒径，能形成无色、透明滑爽的涂膜。产品性能优异，具有良好的抗发白性、低吸水性和高耐候性。 | |
| Acronal® ECO 338 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种细粒径，低黏度的水性乳液。无气味，而且不包含氨水，溶剂及增塑剂。它与常用的颜料与填料展现优异的相容性。形成的涂膜透明，柔性且有光泽，并具备好的耐水性及耐水解性。 | |
| Acronal® ECO 502 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是低黏度，细小乳胶，无气味，不含氨水及任何溶剂或增塑剂，拥有出色的颜料相容性和粘结能力，而且配方内不需要助成膜助剂。其干膜透明，有光泽和弹性，并有很好的耐水和抗水解性能。 | |
| Acronal® ECO 612 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 全丙烯酸共聚物，用于低光泽建筑涂料。用Acronal®ECO 612 ap形成的涂料能在保持VOC含量接近零的条件下满足严苛性能。由于其出色的附着力和抗粘连性能，Acronal®ECO 612 ap配制的涂料非常适合各种表面类型和应用。另外，Acronal®ECO 612 ap表现出优秀的耐常规家庭污染物的能力 | |
| Acronal® ECO 702 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种阴离子型中等黏度，细小粒径的水性乳胶。拥有优异的颜料和填料的相容性与粘结性能。Acronal ECO 702 ap 在无颜填料时形成的膜透明，有弹性和光泽，并具有出色的耐水和抗皂化性能。 | |
| Acronal® ECO 9056 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 阴离子乳液聚合物，具有中等粘度。它含有细小良好分散的颗粒。它与颜料和填料具有出色的相容性。它具有非常高的颜料粘合力。未着色的Acronal®ECO 9056涂膜可在室温下指干。Acronal®ECO 9056的涂膜透明、柔韧和高光，具有极高的耐水性和非常好的耐皂化性能 | |
| Acronal® Flex SC 138 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 良好分散的聚合物乳液，粘度低。与填料和颜料具有出色的相容性。它具有非常高的颜料粘合力。用Acronal®FLEX SC 138形成的涂膜具有出色的耐水、耐碱性能和耐候性。Acronal®FLEX SC 138配制的弹性墙面涂料即使在温暖高污染的环境下也具有良好的耐毛细裂纹以及非常好的耐玷污性能 | |
| Acronal® GS 409 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种低粘度细小粒径聚合物乳液。它与填料和颜料具有优异的相容性，同时具有极高的颜料粘结力。由Acronal GS 409 ap形成的漆膜具有优异的耐水性、耐碱性和耐候性。采用Acronal GS 409 ap配制的弹性涂料能能够提供毛细裂纹的桥接，即使在温暖和污染的环境中，也具有非常出色的耐沾污性。 | |
| Acronal® JC 7043 X | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种拥有细小粒径和低粘度的阴离子R-C乳液。它是一 种长链的丙烯酸和苯乙烯共聚物，具备优异的对粉化基材的渗透性和优异的耐碱性，适用于水性渗透性和耐碱性底漆，该底漆可替代溶剂型体系。该产品对粉化砖石基材具有优异的粘结力。 Acronal® JC 7043 适用于制备全效合一水性底漆产品。 | |
| Acronal® PA 510 | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 是一种阴离子型的分散介质的粘度。该乳液具有非常细的颗粒，提供优良的增稠响应。 ACRONAL®PA510配方的高光泽涂料耐高挡。 ACRONAL®PA510具有优异的湿附着力对木材和任何关键基材，尤其是老化醇酸的基材. | |
| Acronal® PA 807 ap | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 乳液聚合物，耐久、低粘灰，用于高品质户外乳胶漆。Acronal® PA 807 ap是一种阴离子乳液聚合物，粘度中等，含有细小、良好分散的颗粒。它是一种全丙烯酸共聚物具有出色的户外耐久性和良好的耐玷污性能。该聚合物制备的涂膜具有良好的耐擦洗性能，防粘连性能，良好的对圬工表面的附着力以及特别好的湿遮盖力。Acronal® PA 807 ap适合用于制备各种应用的油漆，可配制不同光泽水平。 | |
| Acronal® PS 791 AP | BASF Dispersions & Pigments Asia Pacific 巴斯夫亚洲分散液 & 颜料 | 乳液聚合物，用于高品质通用型建筑涂料，Acronal® PS 791 ap是一种阴离子乳液聚合物，粘度低，含有细小、良好分散的颗粒。它具有与颜填料出色的相容性和非常高的颜料粘合力。未着色的Acronal® PS 791 ap涂膜可在室温下指干。Acronal® PS 791 ap形成的涂膜透明、柔韧、光泽高，具有极高的耐水性，和非常好的耐皂化性能 | |
| KRATON® D1101 JO Polymer | Kraton Polymers International Ltd. | KRATON® D1101 JO Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as a crumb dusted with organic dusting agent. This product is versatile with a combination of high strength, wi...展开 KRATON® D1101 JO Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as a crumb dusted with organic dusting agent. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1101 JO Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1101 JSM Polymer | Kraton Polymers International Ltd. | KRATON® D1101 JSM Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as a powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide ...展开 KRATON® D1101 JSM Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as a powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1101 JSM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1101 JU Polymer | Kraton Polymers International Ltd. | KRATON® D1101 JU Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as a undusted crumb. This product is versatile with a combination of high strength, wide range of hardness, and...展开 KRATON® D1101 JU Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as a undusted crumb. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1101 JU Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1102 JS Polymer | Kraton Polymers International Ltd. | KRATON® D1102 JS Polymer is a clear linear block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide ra...展开 KRATON® D1102 JS Polymer is a clear linear block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1102 JS Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1102 JSZ Polymer | Kraton Polymers International Ltd. | KRATON® D1102 JSZ Polymer is a clear linear block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide r...展开 KRATON® D1102 JSZ Polymer is a clear linear block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1102 JSZ Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1111 KT Polymer | Kraton Polymers International Ltd. | KRATON® D1111 KT Polymer is a linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low viscosi...展开 KRATON® D1111 KT Polymer is a linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1111 KT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1111 KU Polymer | Kraton Polymers International Ltd. | KRATON® D1111 KU Polymer is a linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as non-dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low vis...展开 KRATON® D1111 KU Polymer is a linear triblock copolymer based on styrene and butadiene with a polystyrene content of 31%. It is supplied as non-dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1111 KU Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1113 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1113 BT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as dusted pellets. This product is versatile with a combination of high strength, low hardness, and low viscosit...展开 KRATON® D1113 BT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as dusted pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1113 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1113 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1113 PT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low visco...展开 KRATON® D1113 PT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1113 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1114 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1114 BT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 19%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness,...展开 KRATON® D1114 BT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 19%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1114 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1114 PSM Polymer | Kraton Polymers International Ltd. | KRATON® D1114 PSM Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 19%. It is supplied as powder dusted with silica. This product is versatile with a combination of high strength, low hardness, and ...展开 KRATON® D1114 PSM Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 19%. It is supplied as powder dusted with silica. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1114 PSM Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1114 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1114 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 19%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low vi...展开 KRATON® D1114 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 19%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1114 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1116 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1116 ES Polymer is a clear, radial triblock copolymer based on styrene and butadiene with a polystyrene content of 23%. It is supplied as a porous pellet dusted with an amorphous silica. This product is versatile with a combination of high streng...展开 KRATON® D1116 ES Polymer is a clear, radial triblock copolymer based on styrene and butadiene with a polystyrene content of 23%. It is supplied as a porous pellet dusted with an amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1116 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1116 ESM Polymer | Kraton Polymers International Ltd. | KRATON® D1116 ESM Polymer is a clear, radial triblock copolymer based on styrene and butadiene with a polystyrene content of 23%. It is supplied as a powder dusted with an amorphous silica. This product is versatile with a combination of high strength, wi...展开 KRATON® D1116 ESM Polymer is a clear, radial triblock copolymer based on styrene and butadiene with a polystyrene content of 23%. It is supplied as a powder dusted with an amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1116 ESM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1117 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1117 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 17%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low vi...展开 KRATON® D1117 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 17%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1117 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 AS Polymer | Kraton Polymers International Ltd. | KRATON® D1118 AS Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide ran...展开 KRATON® D1118 AS Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 AS Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1118 ASM Polymer | Kraton Polymers International Ltd. | KRATON® D1118 ASM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of h...展开 KRATON® D1118 ASM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 ASM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1118 AT Polymer | Kraton Polymers International Ltd. | KRATON® D1118 AT Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardne...展开 KRATON® D1118 AT Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 AT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, sealants, and coatings. 收起 | |
| KRATON® D1118 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1118 BT Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range o...展开 KRATON® D1118 BT Polymer is a clear, linear triblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 BT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1118 ES Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide ran...展开 KRATON® D1118 ES Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 ESM Polymer | Kraton Polymers International Ltd. | KRATON® D1118 ESM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of h...展开 KRATON® D1118 ESM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 ESM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 ET Polymer | Kraton Polymers International Ltd. | KRATON® D1118 ET Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardne...展开 KRATON® D1118 ET Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 ET Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 ETM Polymer | Kraton Polymers International Ltd. | KRATON® D1118 ETM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as powder dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and...展开 KRATON® D1118 ETM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as powder dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 ETM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 KT Polymer | Kraton Polymers International Ltd. | KRATON® D1118 KT Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, wide range of hardness, and lo...展开 KRATON® D1118 KT Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 KT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1118 KTM Polymer | Kraton Polymers International Ltd. | KRATON® D1118 KTM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as dusted powder. This product is versatile with a combination of high strength, wide range of hardness, and low visco...展开 KRATON® D1118 KTM Polymer is a clear, diblock copolymer based on styrene and butadiene with a polystyrene content of 33%. It is supplied as dusted powder. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1118 KTM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1119 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1119 BT Polymer is a clear, linear triblock copolymer based on styrene asnd isoprene with a polystyrene content of 22%. It is supplied as porous pellet dusted with talc. This product is versatile with a combination of high strength, low hardness,...展开 KRATON® D1119 BT Polymer is a clear, linear triblock copolymer based on styrene asnd isoprene with a polystyrene content of 22%. It is supplied as porous pellet dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1119 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1119 PSM Polymer | Kraton Polymers International Ltd. | KRATON® D1119 PSM Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 22%. It is supplied as powder dusted with silica. This product is versatile with a combination of high strength, low hardness, and ...展开 KRATON® D1119 PSM Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 22%. It is supplied as powder dusted with silica. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1119 PSM Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1119 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1119 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 22%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low vi...展开 KRATON® D1119 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 22%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1119 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1124 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1124 BT Polymer is a clear, branched triblock copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardnes...展开 KRATON® D1124 BT Polymer is a clear, branched triblock copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1124 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1124 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1124 PT Polymer is a clear, branched copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity...展开 KRATON® D1124 PT Polymer is a clear, branched copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1124 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1126 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1126 PT Polymer is a clear, radial copolymer based on styrene and isoprene, with a polystyrene content of 21%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity ...展开 KRATON® D1126 PT Polymer is a clear, radial copolymer based on styrene and isoprene, with a polystyrene content of 21%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1126 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1152 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1152 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1152 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1152 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1153 AS Polymer | Kraton Polymers International Ltd. | KRATON® D1153 AS Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1153 AS Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1153 AS Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1153 AT Polymer | Kraton Polymers International Ltd. | KRATON® D1153 AT Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of ha...展开 KRATON® D1153 AT Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1153 AT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1153 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1153 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1153 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1153 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1155 BO Polymer | Kraton Polymers International Ltd. | KRATON® D1155 BO Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as dusted, porous pellets. This product is versatile with a combination of high strength, wide range of hardness, and...展开 KRATON® D1155 BO Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as dusted, porous pellets. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1155 BO Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1155 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1155 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide r...展开 KRATON® D1155 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1155 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1155 JO Polymer | Kraton Polymers International Ltd. | KRATON® D1155 JO Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, wide range of hardness, and l...展开 KRATON® D1155 JO Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1155 JO Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1155 JOP Polymer | Kraton Polymers International Ltd. | KRATON® D1155 JOP Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, wide range of hardness, and ...展开 KRATON® D1155 JOP Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 40% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1155 JOP Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1157 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1157 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1157 ES Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1157 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1157 ETM Polymer | Kraton Polymers International Ltd. | KRATON® D1157 ETM Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as powder dusted with talc. This product is versatile with a combination of high strength, wide range of hardness,...展开 KRATON® D1157 ETM Polymer is a clear, linear block copolymer based on styrene and butadiene with bound styrene of 29.5% mass. It is supplied as powder dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1157 ETM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1160 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1160 BT Polymer is a clear linear triblock copolymer based on styrene and isoprene with bound styrene of 18.5% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, a...展开 KRATON® D1160 BT Polymer is a clear linear triblock copolymer based on styrene and isoprene with bound styrene of 18.5% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1160 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 BO Polymer | Kraton Polymers International Ltd. | KRATON® D1161 BO Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as porous pellets dusted with Calcium Stearate. This product is versatile with a combination of high strength, low ...展开 KRATON® D1161 BO Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as porous pellets dusted with Calcium Stearate. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 BO Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 BSM Polymer | Kraton Polymers International Ltd. | KRATON® D1161 BSM Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as powder dusted with silica. This product is versatile with a combination of high strength, low hardness, and low...展开 KRATON® D1161 BSM Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as powder dusted with silica. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 BSM Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1161 BT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, an...展开 KRATON® D1161 BT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 JS Polymer | Kraton Polymers International Ltd. | KRATON® D1161 JS Polymer is a clear, linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as dusted crumbs. This product is versatile with a combination of high strength, low hardness, and low viscosity for e...展开 KRATON® D1161 JS Polymer is a clear, linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as dusted crumbs. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 JS Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 JSP Polymer | Kraton Polymers International Ltd. | KRATON® D1161 JSP Polymer is a clear, linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosi...展开 KRATON® D1161 JSP Polymer is a clear, linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 JSP Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 JU Polymer | Kraton Polymers International Ltd. | KRATON® D1161 JU Polymer is a clear, linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as non-dusted crumbs. This product is versatile with a combination of high strength, low hardness, and low viscosity f...展开 KRATON® D1161 JU Polymer is a clear, linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as non-dusted crumbs. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 JU Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 KT Polymer | Kraton Polymers International Ltd. | KRATON® D1161 KT Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low ...展开 KRATON® D1161 KT Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 KT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 KU Polymer | Kraton Polymers International Ltd. | KRATON® D1161 KU Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as non-dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and ...展开 KRATON® D1161 KU Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as non-dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 KU Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1161 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low v...展开 KRATON® D1161 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1161 PTM Polymer | Kraton Polymers International Ltd. | KRATON® D1161 PTM Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted powder. This product is versatile with a combination of high strength, low hardness, and low viscosi...展开 KRATON® D1161 PTM Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted powder. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1161 PTM Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1162 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1162 BT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 43%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness,...展开 KRATON® D1162 BT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 43%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1162 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1162 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1162 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 43%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low vi...展开 KRATON® D1162 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 43%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1162 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1163 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1163 BT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, an...展开 KRATON® D1163 BT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 15%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1163 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1163 JSP Polymer | Kraton Polymers International Ltd. | KRATON® D1163 JSP Polymer is a clear linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosit...展开 KRATON® D1163 JSP Polymer is a clear linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1163 JSP Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1163 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1163 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low v...展开 KRATON® D1163 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1163 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1163 PTM Polymer | Kraton Polymers International Ltd. | KRATON® D1163 PTM Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted powder. This product is versatile with a combination of high strength, low hardness, and low viscosi...展开 KRATON® D1163 PTM Polymer is a clear, linear triblock copolymer based on styrene and isoprene, with a polystyrene content of 15%. It is supplied as dusted powder. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1163 PTM Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1164 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1164 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 29%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low vi...展开 KRATON® D1164 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 29%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1164 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1165 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1165 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low vi...展开 KRATON® D1165 PT Polymer is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1165 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1170 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1170 BT Polymer is a clear, linear triblock copolymer based on styrene, butadiene and isoprene with a polystyrene content of 19%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, lo...展开 KRATON® D1170 BT Polymer is a clear, linear triblock copolymer based on styrene, butadiene and isoprene with a polystyrene content of 19%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1170 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1171 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1171 PT Polymer is a clear, linear triblock copolymer based on styrene, butadiene and isoprene with a polystyrene content of 19%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness,...展开 KRATON® D1171 PT Polymer is a clear, linear triblock copolymer based on styrene, butadiene and isoprene with a polystyrene content of 19%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1171 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, and hot melt adhesives. 收起 | |
| KRATON® D1173 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1173 BT Polymer is a clear, linear triblock copolymer based on styrene, butadiene and isoprene with a polystyrene content of 18%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, low hardness...展开 KRATON® D1173 BT Polymer is a clear, linear triblock copolymer based on styrene, butadiene and isoprene with a polystyrene content of 18%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1173 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, and hot melt adhesives. 收起 | |
| KRATON® D1183 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1183 BT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, an...展开 KRATON® D1183 BT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1183 BT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1183 PT Polymer | Kraton Polymers International Ltd. | KRATON® D1183 PT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low visco...展开 KRATON® D1183 PT Polymer is a clear, linear block copolymer based on styrene and isoprene with a polystyrene content of 16%. It is supplied as dusted dense pellets. This product is versatile with a combination of high strength, low hardness, and low viscosity for easy thermoplastic processing as a melt or in solution. KRATON® D1183 PT Polymer is used in pressure sensitive adhesives, hot melt spray, diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 AIM Polymer | Kraton Polymers International Ltd. | KRATON® D1184 AIM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with calcium carbonate. This product is versatile with a combination of high strength, wide range...展开 KRATON® D1184 AIM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with calcium carbonate. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 AIM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 AS Polymer | Kraton Polymers International Ltd. | KRATON® D1184 AS Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1184 AS Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 AS Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 ASM Polymer | Kraton Polymers International Ltd. | KRATON® D1184 ASM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range ...展开 KRATON® D1184 ASM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 ASM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 AT Polymer | Kraton Polymers International Ltd. | KRATON® D1184 AT Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of ha...展开 KRATON® D1184 AT Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 AT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 ES Polymer | Kraton Polymers International Ltd. | KRATON® D1184 ES Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1184 ES Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 ES Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1184 ESM Polymer | Kraton Polymers International Ltd. | KRATON® D1184 ESM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range ...展开 KRATON® D1184 ESM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 ESM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1184 ET Polymer | Kraton Polymers International Ltd. | KRATON® D1184 ET Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of ha...展开 KRATON® D1184 ET Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 ET Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1184 KIM Polymer | Kraton Polymers International Ltd. | KRATON® D1184 KIM Polymer is a clear, branched triblock copolymer based on styrene and butadiene, with a polystyrene content of 31%. It is supplied as dusted powder. This product is versatile with a combination of high strength, wide range of hardness, an...展开 KRATON® D1184 KIM Polymer is a clear, branched triblock copolymer based on styrene and butadiene, with a polystyrene content of 31%. It is supplied as dusted powder. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 KIM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 KT Polymer | Kraton Polymers International Ltd. | KRATON® D1184 KT Polymer is a clear, branched triblock copolymer based on styrene and butadiene, with a polystyrene content of 31%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, wide range of hardn...展开 KRATON® D1184 KT Polymer is a clear, branched triblock copolymer based on styrene and butadiene, with a polystyrene content of 31%. It is supplied as dusted porous pellets. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 KT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1184 KU Polymer | Kraton Polymers International Ltd. | KRATON® D1184 KU Polymer is a clear, branched triblock copolymer based on styrene and butadiene, with a polystyrene content of 31%. It is supplied as non-dusted porous pellets. This product is versatile with a combination of high strength, wide range of h...展开 KRATON® D1184 KU Polymer is a clear, branched triblock copolymer based on styrene and butadiene, with a polystyrene content of 31%. It is supplied as non-dusted porous pellets. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1184 KU Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 | |
| KRATON® D1186 AS Polymer | Kraton Polymers International Ltd. | KRATON® D1186 AS Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide...展开 KRATON® D1186 AS Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1186 AS Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1186 ASM Polymer | Kraton Polymers International Ltd. | KRATON® D1186 ASM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range ...展开 KRATON® D1186 ASM Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as powder dusted with amorphous silica. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1186 ASM Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1186 AT Polymer | Kraton Polymers International Ltd. | KRATON® D1186 AT Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of ha...展开 KRATON® D1186 AT Polymer is a clear, branched block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1186 AT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, road and pipe coatings, and sealants. 收起 | |
| KRATON® D1186 BT Polymer | Kraton Polymers International Ltd. | KRATON® D1186 BT Polymer is a clear, branched triblock copolymer based on styrene and butadiene with a polystyrene content of 30%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range...展开 KRATON® D1186 BT Polymer is a clear, branched triblock copolymer based on styrene and butadiene with a polystyrene content of 30%. It is supplied as porous pellets dusted with talc. This product is versatile with a combination of high strength, wide range of hardness, and low viscosity for easy thermoplastic melt processing or processing in solution. KRATON® D1186 BT Polymer is used in pressure sensitive adhesives, hot melt spray diaper adhesives, construction adhesives, coatings, and sealants. 收起 |
