| A-C 316A | DKSH | A-C 316A is a hard, high drop point, high density, oxidized polyethylene (HDOxPEs) homopolymer, in finer powder form than A C 316, for use in waterborne coatings and inks, overprint varnishes, polishes and textiles to improve surface properties including ...展开 A-C 316A is a hard, high drop point, high density, oxidized polyethylene (HDOxPEs) homopolymer, in finer powder form than A C 316, for use in waterborne coatings and inks, overprint varnishes, polishes and textiles to improve surface properties including mar and abrasion resistance by lowering the coefficient of friction. In textiles, this can help improve sewability and fabric cutting, helping to extend cutting machine lifetime. Its acid number of 16 allows it to be emulsified into water. Can also provide heat resistance to hot melt adhesives (HMAs). In addition, may be used as a metal release agent for PVC processing and is a fusion control for PVC formulations. It will not affect clarity in transparent PVC applications. Very effective for use in processing PVC regrind. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 325 | DKSH | A-C 325 is a Hard, high drop point, high density, oxidized polyethylene (HDOxPEs) homopolymer powder (granule) for use in water borne coatings and inks, overprint varnishes, polishes and textiles to improve surface properties including mar and abrasion re...展开 A-C 325 is a Hard, high drop point, high density, oxidized polyethylene (HDOxPEs) homopolymer powder (granule) for use in water borne coatings and inks, overprint varnishes, polishes and textiles to improve surface properties including mar and abrasion resistance by lowering the coefficient of friction. In textiles, this can help improve sewability and fabric cutting, extending cutting machine lifetime. Its acid number of 25 allows it to be emulsified into water. Can also provide heat resistance to hot melt adhesives (HMAs). This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 400 | DKSH | A-C 400 is a Ethylene vinyl acetate (EVA) copolymer in prill form, with a VA content of 13%, used extensively in hot melt adhesives (HMAs) to control rheology and boost adhesion. It can be added as a diluent but provides the dual function of reducing appl...展开 A-C 400 is a Ethylene vinyl acetate (EVA) copolymer in prill form, with a VA content of 13%, used extensively in hot melt adhesives (HMAs) to control rheology and boost adhesion. It can be added as a diluent but provides the dual function of reducing application viscosity at melt, while providing an adhesion boost versus homopolymer, non functional diluents (FT, byproduct, thermally degraded (TD) and PE homopolymer waxes). It is completely miscible in EVA adhesive resins, as would be expected by the similar chemistry. It is also used in candles to provide paraffin crystal nucleation, which increases thermal and breakage resistance, adhesion to glass, and fragrance retention. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 400A | DKSH | A-C 400A is a Ethylene vinyl acetate (EVA) copolymer in powder form, with a VA content of 13%, used extensively in hot melt adhesives (HMAs) to control rheology and boost adhesion. It can be added as a diluent but provides the dual function of reducing ap...展开 A-C 400A is a Ethylene vinyl acetate (EVA) copolymer in powder form, with a VA content of 13%, used extensively in hot melt adhesives (HMAs) to control rheology and boost adhesion. It can be added as a diluent but provides the dual function of reducing application viscosity at melt, while providing an adhesion boost versus homopolymer, non functional diluents (FT, byproduct, thermally degraded (TD) and PE homopolymer waxes). It is completely miscible in EVA adhesive resins, as would be expected by the similar chemistry. It is also used in candles to provide paraffin crystal nucleation, which raises thermal and breakage resistance, adhesion to glass, and fragrance retention. Is also a dispersing agent for color masterbatch in stryenic resins. Excellent dispersing agent and process aid for EVA-based wire and cable compounds. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 405M | DKSH | A-C 405M is an ethylene vinyl acetate (EVA) copolymer in prill form, with a VA content of 8%, for use in solvent borne coatings to control rheology and provide metallic flake orientation. Used extensively in automotive basecoats. This product is available...展开 A-C 405M is an ethylene vinyl acetate (EVA) copolymer in prill form, with a VA content of 8%, for use in solvent borne coatings to control rheology and provide metallic flake orientation. Used extensively in automotive basecoats. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 405T | DKSH | A-C 405T is an ethylene vinyl acetate (EVA) copolymer in prill form, with a VA content of 6%, for use in solvent borne coatings to control rheology and provide metallic flake orientation. Used extensively in automotive basecoats. This product is available...展开 A-C 405T is an ethylene vinyl acetate (EVA) copolymer in prill form, with a VA content of 6%, for use in solvent borne coatings to control rheology and provide metallic flake orientation. Used extensively in automotive basecoats. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 540 | DKSH | A-C 540 is an ethylene acrylic acid (EAA) copolymer in a prill form, with an acrylic acid (AA) content of 5%, for use in adhesives to promote adhesion to various substrates. It is also used in aqueous floor polishes to provide drag (raising the coefficien...展开 A-C 540 is an ethylene acrylic acid (EAA) copolymer in a prill form, with an acrylic acid (AA) content of 5%, for use in adhesives to promote adhesion to various substrates. It is also used in aqueous floor polishes to provide drag (raising the coefficient of friction) thereby controlling the final coefficient of friction. Its acid number of 40 aids emulsification. Also used in solvent borne coatings to control rheology and provide metallic flake orientation. Used extensively in automotive basecoats. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 540A | DKSH | A-C 540A is a Ethylene acrylic acid (EAA) copolymer in a powdered form, with an acrylic acid (AA) content of 5%, for use in adhesives to promote adhesion to various substrates. It is also used in aqueous floor polishes to provide drag (raising the coeffic...展开 A-C 540A is a Ethylene acrylic acid (EAA) copolymer in a powdered form, with an acrylic acid (AA) content of 5%, for use in adhesives to promote adhesion to various substrates. It is also used in aqueous floor polishes to provide drag (raising the coefficient of friction) thereby controlling the final coefficient of friction. Its acid number of 40 aids emulsification. Also used in solvent borne coatings to control rheology and provide metallic flake orientation. Used extensively in automotive basecoats. Is a dispersing agent for color masterbatch in engineering resins. Excellent external lubricant for polyamide compounds.This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 6 | DKSH | A-C 6 is a low density polyethylene (LDPE) homopolymer in a prill form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also used as...展开 A-C 6 is a low density polyethylene (LDPE) homopolymer in a prill form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also used as a gellant for hydrocarbon oils, a paraffin crystal nucleator in wax blends such as candles, and a viscosity diluent in HMAs. Can also be partially substituted for FT (Fisher Tropsch) Wax in adhesive applications without detracting from formulation properties. Used in cable flooding compounds, along with polybutene. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 617 | DKSH | A-C 617 is a Low density polyethylene (LDPE) homopolymer in a prill form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also used ...展开 A-C 617 is a Low density polyethylene (LDPE) homopolymer in a prill form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also used as a gellant for hydrocarbon oils, a paraffin crystal nucleator in wax blends such as candles, and a viscosity diluent in HMAs. Can also be partially substituted for FT (Fisher Tropsch) Wax in adhesive applications without detracting from formulation properties. Is used as a dispersing agent in color masterbatch applications. In PVC applications it finds use as an external lubricant. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 617A | DKSH | A-C 617A is a low density polyethylene (LDPE) homopolymer in a powdered form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also u...展开 A-C 617A is a low density polyethylene (LDPE) homopolymer in a powdered form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also used as a gellant for hydrocarbon oils, a paraffin crystal nucleator in wax blends such as candles, and a viscosity diluent in HMAs. Can also be partially substituted for FT (Fisher Tropsch) Wax in adhesive applications without detracting from formulation properties. In PVC applications it finds use as an external lubricant. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 629 | DKSH | A-C 629 is a low density Oxidized Polyethylene (LDOxPE) homopolymer in prill form for use in solvent borne coatings as a rheological aid. It also finds use as a metal release agent in PVC. It can also be atmospherically emulsified for use in aqueous appli...展开 A-C 629 is a low density Oxidized Polyethylene (LDOxPE) homopolymer in prill form for use in solvent borne coatings as a rheological aid. It also finds use as a metal release agent in PVC. It can also be atmospherically emulsified for use in aqueous applications, such as textiles, lubricants, coatings and inks, to lower the COF and provide surface properties such as mar & abrasion resistance and increased slip. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 629A | DKSH | A-C 629A is a low density Oxidized Polyethylene (LDOxPE) homopolymer in prill form for use in solvent borne coatings as a rheological aid. It also finds use as a metal release agent in PVC. It is a pigment dispersing agent for color masterbatch. It can al...展开 A-C 629A is a low density Oxidized Polyethylene (LDOxPE) homopolymer in prill form for use in solvent borne coatings as a rheological aid. It also finds use as a metal release agent in PVC. It is a pigment dispersing agent for color masterbatch. It can also be atmospherically emulsified for use in aqueous applications, such as textiles, lubricants, coatings and inks, to lower the COF and provide surface properties such as mar & abrasion resistance and increased slip. This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| A-C 6A | DKSH | A-C 6A is a low density polyethylene (LDPE) homopolymer in a powdered form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also use...展开 A-C 6A is a low density polyethylene (LDPE) homopolymer in a powdered form, for use in solvent borne coatings, heatset and liquid solvent borne inks, to improve surface properties such as rub, mar & abrasion resistance, by lowering the COF. It is also used as a gellant for hydrocarbon oils, a paraffin crystal nucleator in wax blends such as candles, and a viscosity diluent in HMAs. Can also be partially substituted for FT (Fisher Tropsch) Wax in adhesive applications without detracting from formulation properties. Used in cable flooding compounds, along with polybutene. Is used as a dispersing agent in color masterbatch applications.This product is available in China, Philippines, Australia and New Zealand. 收起 | Request Sample |
| Acrylic Resin GA-003 | DKSH | Acrylic Resin GA-003 is a solid acrylic resin containing epoxy functionality (GMA acrylic). It is used in thermosetting powder coatings to provide excellent outdoor durability. Typical applications include automotive trim and wheel clear coat. GA-003 can ...展开 Acrylic Resin GA-003 is a solid acrylic resin containing epoxy functionality (GMA acrylic). It is used in thermosetting powder coatings to provide excellent outdoor durability. Typical applications include automotive trim and wheel clear coat. GA-003 can be used with curative like 1, 12-dodecanedioic acid (DDDA) to produce clear coating of high gloss, smoothness and clarity. Other polyacrylic acids and polyanhydrides can also be used as curatives for specific coating properties. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| CO2PURE AIR PURIFIER | DKSH | CO2PURE AIR PURIFIER is an organic Painting with Single environmental technology, cleanses and purifies air, works day and night against environmental pollution by reducing gases CO2, NOx and VOC's, its lack of smell makes it particularly suitable for pai...展开 CO2PURE AIR PURIFIER is an organic Painting with Single environmental technology, cleanses and purifies air, works day and night against environmental pollution by reducing gases CO2, NOx and VOC's, its lack of smell makes it particularly suitable for painting walls, ceilings indoors and outdoors, public places, schools, hospitals etc. This product is available in Asia. 收起 | Request Sample |
| DENSURF HR 700A | DKSH | DENSURF HR 700A is ambient curing silicon resin used in heat and corrosion resistant coatings. Thermal stability up to 600-650 °C and corrosion protection are achieved in combination with the suitable formulations. This product is available for North Ame...展开 DENSURF HR 700A is ambient curing silicon resin used in heat and corrosion resistant coatings. Thermal stability up to 600-650 °C and corrosion protection are achieved in combination with the suitable formulations. This product is available for North America and for Japan, India, South Korea, Taiwan and China in Asia (all other countries are excluded). 收起 | Request Sample |
| DENSURF HR 800 | DKSH | DENSURF HR 800 is an air-drying silicon resin used in heat resistant coatings. It is compatible with organic resins such as alkyd resin. It gives thermal stability up to 650°C when formulated with suitable thermally stable pigments and fillers such as alu...展开 DENSURF HR 800 is an air-drying silicon resin used in heat resistant coatings. It is compatible with organic resins such as alkyd resin. It gives thermal stability up to 650°C when formulated with suitable thermally stable pigments and fillers such as aluminum and iron oxide pigments. This product is available for North America and for Japan, India, South Korea, Taiwan and China in Asia (all other countries are excluded). 收起 | Request Sample |
| DENSURF HR 900 | DKSH | DENSURF HR 900 is an air-drying silicon resin used in heat resistant coatings. It is compatible with organic resins such as alkyd resin. It gives thermal stability up to 650°C when formulated with suitable thermally stable pigments and fillers such as alu...展开 DENSURF HR 900 is an air-drying silicon resin used in heat resistant coatings. It is compatible with organic resins such as alkyd resin. It gives thermal stability up to 650°C when formulated with suitable thermally stable pigments and fillers such as aluminum and iron oxide pigments. This product is available for North America and for Japan, India, South Korea, Taiwan and China in Asia (all other countries are excluded). 收起 | Request Sample |
| GMA | DKSH | Glycidyl methacrylate (GMA) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy funct...展开 Glycidyl methacrylate (GMA) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy functionalization to polyolefins and other acrylate resins. Glycidyl methacrylate is produced by several companies worldwide, including Dow Chemical. This product is available in Europe and Asia. 收起 | Request Sample |
| GMA 97 | DKSH | Glycidyl methacrylate (GMA 97) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy fu...展开 Glycidyl methacrylate (GMA 97) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy functionalization to polyolefins and other acrylate resins. Glycidyl methacrylate is produced by several companies worldwide, including Dow Chemical. This product is available in Europe and Asia. 收起 | Request Sample |
| IPDA | DKSH | IPDA is a colorless or pale yellow transparent liquid with an amine-like odor at room temperature. It is a mixture of two stero-isomers of 3-aminomethyl-3,5,5-trimethylcyclohe-xylamine. IPDA is a cycloalifatic diamine with special structure and is used in...展开 IPDA is a colorless or pale yellow transparent liquid with an amine-like odor at room temperature. It is a mixture of two stero-isomers of 3-aminomethyl-3,5,5-trimethylcyclohe-xylamine. IPDA is a cycloalifatic diamine with special structure and is used in all typical reactions of this kind of amine functional chemicals. It is widely miscible with a full range of alifatic, aromatic and halogenated solvents of different polarity. Chemical description: 3-aminomethyl-3,5,5-trimethylcyclohexylamine. This product is available in Europe and Korea. 收起 | Request Sample |
| ITAMID B | DKSH | ITAMID B is a polyaminoamide resin of high viscosity at room temperature and which is used combined with liquid or solid epoxy resins to obtain products hardening even at room temperature and which is used in the anticorrosion paints, protective coatings ...展开 ITAMID B is a polyaminoamide resin of high viscosity at room temperature and which is used combined with liquid or solid epoxy resins to obtain products hardening even at room temperature and which is used in the anticorrosion paints, protective coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces. ITAMID B, which can also be used neat, is usually used in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. In solvent free systems ITAMID B is usually used in combination with liquid epoxy resins giving high adhesion properties. With an epoxy resin of an epoxy weight equivalent of about 190g/eq, ITAMID B is normally used in equal parts. This ratio can be varied, even widely, whilst bearing in mind that a greater percentage of polyamide resin increases flexibility but reduces resistance to chemicals. More frequently ITAMID B is combined with a solid epoxy resin in solvent systems whose pot-life changes with the percentage of solvent and temperature in addition to the type of epoxy resin used. For example, a formulation with 40% of solvents with an epoxy resin of epoxy equivalent weight 475 and a ratio of 65/35 epoxy to polyamide will exhibit a pot-life at room temperature of about two days. 收起 | Request Sample |
| ITAMID C | DKSH | ITAMID C is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C is used above all in the field of anticorrosion paints, protective coatings with high resi...展开 ITAMID C is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C is used above all in the field of anticorrosion paints, protective coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces. ITAMID C, can be dissolved readily in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. In solvent free systems, ITAMID C when used combined with liquid epoxy resins gives rise to products featuring high adhesion properties and which can be applied by spatula process or by spraying. When ITAMID C is used with an epoxy resin with an epoxy equivalent weight of around 190, the normal ratio used is 60 p.p. of epoxy to 40 p.p. of polyaminoamide. However, this ratio can be varied, even widely, whilst bearing in mind that a greater percentage of polyamine resin increases flexibility but reduces resistance to chemicals. In solvent systems ITAMID C is usually combined with a solid epoxy resin whose pot-life changes with the percentage of dryness and temperature in addition to the type of epoxy used. For example, a formulation at dryness 40% with an epoxy resin of epoxy weight equivalent 475 and a ratio of 75/25 epoxy to polyamine will exhibit a pot-life at room temperature of about two days. 收起 | Request Sample |
| ITAMID C/F | DKSH | ITAMID C/F is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C/F is used above all in the field of anticorrosion paints, protective coatings with high ...展开 ITAMID C/F is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C/F is used above all in the field of anticorrosion paints, protective coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces. ITAMID C/F, can be dissolved readily in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. In solvent free systems, ITAMID C/F when used combined with liquid epoxy resins gives rise to products featuring high adhesion properties and which can be applied by spatula process or by spraying. When ITAMID C/F is used with an epoxy resin with an epoxy equivalent weight of around 190, the normal ratio used is 60 p.p. of epoxy to 40 p.p. of polyaminoamide. However, this ratio can be varied, even widely, whilst bearing in mind that a greater percentage of polyamine resin increases flexibility but reduces resistance to chemicals. In solvent systems ITAMID C/F is usually combined with a solid epoxy resin whose pot-life changes with the percentage of dryness and temperature in addition to the type of epoxy used. For example, a formulation at dryness 40% with an epoxy resin of epoxy weight equivalent 475 and a ratio of 75/25 epoxy to polyamine will exhibit a pot-life at room temperature of about two days. 收起 | Request Sample |
| ITAMID D | DKSH | ITAMID D is a rather fluid polyaminoamide resin which is used in combination with epoxy resins, mainly liquid ones, to obtain hardening products even at room temperature and which are used above all in the field of reactive adhesives, solvent free coating...展开 ITAMID D is a rather fluid polyaminoamide resin which is used in combination with epoxy resins, mainly liquid ones, to obtain hardening products even at room temperature and which are used above all in the field of reactive adhesives, solvent free coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces and good thermal resistance. ITAMID D, which is normally used neat, however dissolves readily in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. The low viscosity of ITAMID D when used in combination with liquid epoxy resins gives rise to products which can be applied even by processes of spatula, spraying and pouring. When ITAMID D is used in combination with an epoxy resin with a epoxy equivalent weight of around 190, depending on the applications the ratio between epoxy and polyamine may vary between 65/35 and 75/25 with pot-lives varying between 110 and 130 minutes. It must however be keep in mind that a higher percentage of polyamine resin increases flexibility but reduces the resistance to chemical agents. 收起 | Request Sample |
| ITAMID FL300 | DKSH | ITAMID FL300 is a liquid epoxy resin hardener made up of low viscosity polyaminoamide resin. ITAMID FL300 is to be found used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masses,...展开 ITAMID FL300 is a liquid epoxy resin hardener made up of low viscosity polyaminoamide resin. ITAMID FL300 is to be found used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masses, paints and floorings. Compared with traditional hardeners, ITAMID FL300 exhibits lower sensitivity to carbonatation and higher reactivity. Hardening times can be considerably reduced by including into the formulate either appropriate accelerator substances (e.g. 2-3% of tris(dimethylaminomethyl)phenol) or fastcure hardener like ITAMINE M150 or ITAMINE MB501. 收起 | Request Sample |
| ITAMID FL31 | DKSH | ITAMID FL31 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL31 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings...展开 ITAMID FL31 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL31 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings. Compared with traditional hardeners, ITAMID FL31 exhibits no sensitivity to carbonatation and higher reactivity. Hardening times can be considerably reduced by including into the formulate either appropriate accelerator substances (e.g. 2-3% of tris(dimethylaminomethyl)phenol) or fastcure hardener like ITAMINE M160 or ITAMINE MB501. 收起 | Request Sample |
| ITAMID FL32 | DKSH | ITAMID FL32 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL32 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings...展开 ITAMID FL32 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL32 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings. Compared with traditional hardeners, ITAMID FL32 exhibits no sensitivity to carbonatation and higher reactivity. Hardening times can be considerably reduced by including into the formulate either appropriate accelerator substances (e.g. 2-3% of tris(dimethylaminomethyl)phenol) or fastcure hardener like ITAMINE M160 or ITAMINE MB501. 收起 | Request Sample |
| ITAMID FL328 | DKSH | ITAMID FL328 is a liquid epoxy resin hardener made up of low viscosity, modified polyaminoamide adduct. ITAMID FL328 allow the dispersion of epoxy resin in water. ITAMID FL328 is used in the formulation of epoxy mortars (for laying tiles, repair of concre...展开 ITAMID FL328 is a liquid epoxy resin hardener made up of low viscosity, modified polyaminoamide adduct. ITAMID FL328 allow the dispersion of epoxy resin in water. ITAMID FL328 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.) and primer. 收起 | Request Sample |
| ITAMID FL40/S | DKSH | ITAMID FL40/S is a liquid epoxy resin hardener made up of low viscosity polyaminoamide-imidazoline resin. ITAMID FL40/S is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masse...展开 ITAMID FL40/S is a liquid epoxy resin hardener made up of low viscosity polyaminoamide-imidazoline resin. ITAMID FL40/S is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masses, paints and floorings. Compared with traditional hardeners, ITAMID FL40/S exhibits lower sensitivity to carbonatation and lower reactivity, i.e. it gives longer utilisation and hardening times. 收起 | Request Sample |
| ITAMID FL41W3 | DKSH | ITAMID FL41W3 is a liquid epoxy resin hardener made up of a modified, low viscosity polyaminoamide resin. ITAMID FL41W3 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, encapsulatio...展开 ITAMID FL41W3 is a liquid epoxy resin hardener made up of a modified, low viscosity polyaminoamide resin. ITAMID FL41W3 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, encapsulations and paints. Compared with traditional hardeners, ITAMID FL41W3 exhibits improved resistance to chemical agents and dilute inorganic acids, and pronounced capacity for reaction at low temperatures and in presence of water. 收起 | Request Sample |
| ITAMID FL540 | DKSH | ITAMID FL540, is a liquid epoxy resin hardener made up of a low viscosity, modified polyaminoamide adduct. ITAMID FL540 is used in the formulation of adhesives, epoxy mortars and paints even on wet surfaces and under water. | Request Sample |
| ITAMID M30P | DKSH | ITAMID M30P is a thermoplastic polyamide resin for use in flexographic or gravure lamination inks. The product shows excellent adhesion to many substrates (metal or polyolefin). The product has excellent flexibility and is particularly suitable for bondin...展开 ITAMID M30P is a thermoplastic polyamide resin for use in flexographic or gravure lamination inks. The product shows excellent adhesion to many substrates (metal or polyolefin). The product has excellent flexibility and is particularly suitable for bonding of PVC. 收起 | Request Sample |
| Luna ESBO A | DKSH | Luna ESBO A is an epoxidized soya Oil Acrylate oligomer. Used for UV & EB curable systems, as reactive effective wetter/coupling agent. Key benefits are in UV & EB inks and coatings to improve adhesion and solve delamination issues, to improve flexibility...展开 Luna ESBO A is an epoxidized soya Oil Acrylate oligomer. Used for UV & EB curable systems, as reactive effective wetter/coupling agent. Key benefits are in UV & EB inks and coatings to improve adhesion and solve delamination issues, to improve flexibility and to bring high functionality. Moderate cure speed, with low odor and skin irritancy. Good compatibility with non polar substrates. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-add RC961 | DKSH | Luna-add RC961 is a micronized amide wax to improve degassing of powder coatings applied over porous substrates. The additive also helps to improve surface slip and optimizes the orientation of aluminum modified powder in metallic formulations. This produ...展开 Luna-add RC961 is a micronized amide wax to improve degassing of powder coatings applied over porous substrates. The additive also helps to improve surface slip and optimizes the orientation of aluminum modified powder in metallic formulations. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-cryl 550 | DKSH | Luna-cryl 550 is a glycidyl-functional acrylic hardener designed to produce low gloss, exterior-durable polyester powder coatings. Benefits include consistent gloss, smooth matte appearance and consistent performance. “One-shot” low gloss coatings can be ...展开 Luna-cryl 550 is a glycidyl-functional acrylic hardener designed to produce low gloss, exterior-durable polyester powder coatings. Benefits include consistent gloss, smooth matte appearance and consistent performance. “One-shot” low gloss coatings can be produced by using Luna-cryl 550 in conjunction with polyesters having acid values between 30-35 mg KOH/g. Standard polyester resins used for TGIC, HAA, GMA or Araldite PT-910 powder coatings are well suited for use with Lunacryl 550. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-cryl 700 | DKSH | Luna-cryl 700 is a glycidyl functional acrylic resin which can be used as a curing agent for saturated carboxyl polyesters having low acid values (i.e., 33) to produce exterior durable powder coatings with dead matte to low gloss finishes (60° gloss range...展开 Luna-cryl 700 is a glycidyl functional acrylic resin which can be used as a curing agent for saturated carboxyl polyesters having low acid values (i.e., 33) to produce exterior durable powder coatings with dead matte to low gloss finishes (60° gloss range 0–20). This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-cryl 710 | DKSH | Luna-cryl 710 is a glycidyl functional acrylic resin which can be used as a curing agent for saturated carboxyl polyesters having low acid values (i.e., 33) to produce exterior durable powder coatings with dead matte to low gloss finishes (60° gloss range...展开 Luna-cryl 710 is a glycidyl functional acrylic resin which can be used as a curing agent for saturated carboxyl polyesters having low acid values (i.e., 33) to produce exterior durable powder coatings with dead matte to low gloss finishes (60° gloss range 0–20). Luna-cryl 710 offers improved flexibility as compared to its predecessor, Luna-cryl 700. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-pal A81 | DKSH | Luna-pal A81 is a polyaldehyde resin produced by condensation of urea aliphatic aldehydes. It is ideal for use in Pigment pastes and Industrial coatings. This product is available in Europe, Asia and North America. | Request Sample |
| Luna-pal A81 K | DKSH | Luna-pal A81 K is a polyaldehyde resin with wide solubility and compatibility. It is ideal for use in pigment pastes and industrial coatings. Luna-pal A81 K has a softening range of 80-100ºC. This product is available in Europe, Asia and North America. | Request Sample |
| Luna-pal A91 K | DKSH | Luna-pal A91 K is a polyaldehyde resin with wide solubility and compatibility. It is ideal for use in pigment pastes and industrial coatings. Luna-pal A91 K has a softening range of 90-100ºC. This product is available in Europe, Asia and North America. | Request Sample |
| Luna-pal KY-A81-C (Benzene Free) | DKSH | Luna-pal KY-A81-C (Benzene Free) is a polyaldehyde resin for pigment dispersions, or to optimize pigment dispersion in inks and coatings. It shows excellent compatibility with many coating/printing raw materials. It is soluble in most organic solvents and...展开 Luna-pal KY-A81-C (Benzene Free) is a polyaldehyde resin for pigment dispersions, or to optimize pigment dispersion in inks and coatings. It shows excellent compatibility with many coating/printing raw materials. It is soluble in most organic solvents and has very good wetting and dispersion properties. It is a multifunctional additive used also to improve the adhesion, gloss, hardness, and solid content. It can also be used in universal pigment pastes. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-tex RC3940F | DKSH | Luna-tex RC3940F is a stable combination of modified PTFE and polyethylene waxes for producing a high abrasion resistant and uniform surface texture for powder coatings. The product offers a very consistent textured surface effect. This product is availab...展开 Luna-tex RC3940F is a stable combination of modified PTFE and polyethylene waxes for producing a high abrasion resistant and uniform surface texture for powder coatings. The product offers a very consistent textured surface effect. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-tribo K T405 | DKSH | Luna-tribo K T405 is a masterbatch of an additive in a carboxylated polyester to enhance tribochargeability in powder coatings. Active content: 5% of a hindered tertiary amine. | Request Sample |
| Luna-vin UM 40/50 | DKSH | Luna-vin UM40/50 is a medium molecular weight co-polymer of vinyl chloride and vinyl acetate resin. Chemical name: Vinyl Chloride-Vinyl Acetates Terpolymer. This product is available in Europe, Asia and North America. | Request Sample |
| Luna-vin VAGD-W | DKSH | Luna-vin VAGD-W is a high molecular weight, with hydroxyl functional group, partially hydrolyzed vinyl chloride/vinyl acetate resin. Chemical name: Vinyl Chloride-Vinyl Acetates Terpolymer. This product is available in Europe, Asia and North America. | Request Sample |
| Luna-vin VAGH-W | DKSH | Luna-vin VAGH-W is a high molecular weight, with hydroxyl functional group, partially hydrolyzed vinyl chloride/vinyl acetate resin. Chemical name: Vinyl Chloride-Vinyl Acetates Terpolymer. This product is available in Europe, Asia and North America. | Request Sample |
| Luna-vin VMCC/A-W-N17 | DKSH | Luna-vin VMCC/A-W-N17 is a high molecular weight, with carboxyl functional group, comprised of vinyl chloride, vinyl acetate and maleic acid. Chemical name: Vinyl Chloride-Vinyl Acetates Terpolymer. This product is available in Europe, Asia and North Amer...展开 Luna-vin VMCC/A-W-N17 is a high molecular weight, with carboxyl functional group, comprised of vinyl chloride, vinyl acetate and maleic acid. Chemical name: Vinyl Chloride-Vinyl Acetates Terpolymer. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-vin VMCH-W | DKSH | Luna-vin VMCH-W is a high molecular weight, with carboxyl fuctional group, group, comprised of vinyl chloride, vinyl acetate and maleic acid. Chemical name: Vinyl Chloride-Vinyl Acetates Maleic Acid Terpolymer resin. This product is available in Europe, A...展开 Luna-vin VMCH-W is a high molecular weight, with carboxyl fuctional group, group, comprised of vinyl chloride, vinyl acetate and maleic acid. Chemical name: Vinyl Chloride-Vinyl Acetates Maleic Acid Terpolymer resin. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| Luna-vin VYHH-W (UM55) | DKSH | Luna-vin VYHH-W (UM55) is a high molecular weight copolymer of vinyl chloride and vinyl acetate resin. Chemical name: Vinyl Chloride-Vinyl Acetates Copolymer. This product is available in Europe, Asia and North America. | Request Sample |
| MKC Silicate (Methyl Silicate Origomer) | DKSH | MKC Silicate is a self-cleaning additive for Paints (exterior deco, coil). It is made up of oligomers formed by the partial hydrolysis of tetramethoxysilane. By the hydrolysis of alcoxysilanes, silanol groups are generated and make the coating surface hyd...展开 MKC Silicate is a self-cleaning additive for Paints (exterior deco, coil). It is made up of oligomers formed by the partial hydrolysis of tetramethoxysilane. By the hydrolysis of alcoxysilanes, silanol groups are generated and make the coating surface hydrophilic. In the rain, the hydrophilic surface enhances dirt removal with a self-cleaning effect. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| ROPOL PC-21 | DKSH | ROPOL PC-21 is Polycarbonated based on 1,5 Pentanediol and 1,6 Hexanediol, which enables it to obtain high performance polyurethane preparations, improving weather, heat and hydrolysis resistance. This product is available in Europe and Asia. | Request Sample |
| ROPOL PC-22 | DKSH | ROPOL PC-22 is Polycarbonated based on 1,5 Pentanediol and 1,6 Hexanediol, which enables it to obtain high performance polyurethane preparations, improving weather, heat and hydrolysis resistance. This product is available in Europe and Asia. | Request Sample |
| UVP-1300 (Unsaturated Polyester Acrylate Resin) | DKSH | UVP-1300 (Unsaturated Polyester Acrylate Resin) is a Solid resin for UV cured powder coatings. This product is available in Europe, Asia Pacific. | Request Sample |
| VYLON 103 | DKSH | VYLON 103 is a high molecular weight copolyester with medium Tg. VYLON 103 has very good adhesion properties on PVC, PET and other plastics. VYLON 103 is compliant with FDA 175.105 and EC 10/2011. This product is available in Europe, USA and India. | Request Sample |
| VYLON 200 | DKSH | VYLON 200 is a high molecular weight copolyester, with high Tg. VYLON 200 has an excellent adhesion to various substrate materials such as PET, PVC, and metals... VYLON 200 is suitable for inks, primers, coating and adhesion, heat seal lacquers for fle...展开 VYLON 200 is a high molecular weight copolyester, with high Tg. VYLON 200 has an excellent adhesion to various substrate materials such as PET, PVC, and metals... VYLON 200 is suitable for inks, primers, coating and adhesion, heat seal lacquers for flexible food packaging. VYLON 200 has an excellent flexibility, bending performance, workability, corrosion resistance, durability, heat-resistance, solvent solubility, pigment dispersibility and flame resistance. VYLON 200 is compliant with FDA 175.105 (only for non alcoholic food and beverage) and EC 10/2011. This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLON 600 | DKSH | VYLON 600 is a high molecular weight copolyester with medium Tg. VYLON 600 has excellent adhesion strength on metal, PET and PVC. Particularly recommended on coil coating and TTR. VYLON 600 is compliant with FDA 175.105 (only for non alcoholic food and...展开 VYLON 600 is a high molecular weight copolyester with medium Tg. VYLON 600 has excellent adhesion strength on metal, PET and PVC. Particularly recommended on coil coating and TTR. VYLON 600 is compliant with FDA 175.105 (only for non alcoholic food and beverage) and EC 10/2011. This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLON 630 | DKSH | VYLON 630 is a high molecular weight copolyester with low Tg. VYLON 630 has excellent flexibility and good general adhesion strength. VYLON 630 is recommended for adhesion on PET, PVC, metals, coil and can coatings. VYLON 630 is compliant with FDA 175....展开 VYLON 630 is a high molecular weight copolyester with low Tg. VYLON 630 has excellent flexibility and good general adhesion strength. VYLON 630 is recommended for adhesion on PET, PVC, metals, coil and can coatings. VYLON 630 is compliant with FDA 175.105 (only for non alcoholic food and beverage). This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLON 670 | DKSH | VYLON 670 is a high molecular weight copolyester with low Tg. VYLON 670 has excellent adhesion on metal and PET. VYLON 670 is recommended for heat seal application and coil coating. VYLON 670 is compliant with FDA 175.105 (only for non alcoholic food a...展开 VYLON 670 is a high molecular weight copolyester with low Tg. VYLON 670 has excellent adhesion on metal and PET. VYLON 670 is recommended for heat seal application and coil coating. VYLON 670 is compliant with FDA 175.105 (only for non alcoholic food and beverage) and EC 10/2011 This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLON GK-255 | DKSH | VYLON GK-255 is a high molecular weight copolyester, with high Tg. VYLON GK-255 has an excellent adhesion to various substrate materials such as PET, PVC, and metals... VYLON GK-255 is suitable for inks, primers, coating and adhesion, heat seal lacquer...展开 VYLON GK-255 is a high molecular weight copolyester, with high Tg. VYLON GK-255 has an excellent adhesion to various substrate materials such as PET, PVC, and metals... VYLON GK-255 is suitable for inks, primers, coating and adhesion, heat seal lacquers for flexible food packaging. VYLON GK-255 has an excellent flexibility, solvent solubility with high acid value. VYLON GK-255 is compliant with FDA 175.105 (only for non alcoholic food and beverage) and EC 10/2011. This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLON GK-360 | DKSH | VYLON GK-360 is a high molecular weight copolyester, with high Tg. VYLON GK-360 has an excellent weather resistance compare to other grades, and has good adhesion to PET and metal substrates. VYLON GK-360 is suitable for can and coil coatings, screen pr...展开 VYLON GK-360 is a high molecular weight copolyester, with high Tg. VYLON GK-360 has an excellent weather resistance compare to other grades, and has good adhesion to PET and metal substrates. VYLON GK-360 is suitable for can and coil coatings, screen printing inks, primers, coating and adhesion, heat seal lacquers for flexible food packaging. VYLON GK-360 is compliant with FDA 175.105. This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLON GK-888 | DKSH | VYLON GK-888 is a high molecular weight copolyester, with high Tg. VYLON GK-888 has an excellent chemical resistance due to its high Tg. VYLON GK-888 is suitable for can and coil coatings. VYLON GK-888 is compliant with FDA 175.105 and EC 10/2011. Thi...展开 VYLON GK-888 is a high molecular weight copolyester, with high Tg. VYLON GK-888 has an excellent chemical resistance due to its high Tg. VYLON GK-888 is suitable for can and coil coatings. VYLON GK-888 is compliant with FDA 175.105 and EC 10/2011. This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLONAL MD-1480 | DKSH | VYLONAL MD-1480 is a waterbased, high molecular weight copolyester. VYLONAL MD-1480 series have a Low Tg, are 100% solvent free and have Good adhesion strength on PET. VYLONAL MD-1480 series are compliant with FDA 175.105 and EC 10/2011 This product ...展开 VYLONAL MD-1480 is a waterbased, high molecular weight copolyester. VYLONAL MD-1480 series have a Low Tg, are 100% solvent free and have Good adhesion strength on PET. VYLONAL MD-1480 series are compliant with FDA 175.105 and EC 10/2011 This product is available in Europe, USA and India. 收起 | Request Sample |
| VYLONAL MD-2000 | DKSH | VYLONAL MD-2000 is a waterbased, high molecular weight copolyester. VYLONAL MD-2000 series have a high Tg, are 100% solvent free and have Good adhesion strength on PET. VYLONAL MD-2000 series are compliant with FDA 175.105 and EC 10/2011. This produc...展开 VYLONAL MD-2000 is a waterbased, high molecular weight copolyester. VYLONAL MD-2000 series have a high Tg, are 100% solvent free and have Good adhesion strength on PET. VYLONAL MD-2000 series are compliant with FDA 175.105 and EC 10/2011. This product is available in Europe, USA and India. 收起 | Request Sample |
| Wannate IPDI | DKSH | Wannate IPDI is a cycloaliphatic diisocyanate and as such a prefered raw material for the the synthesis of lightstable and water-risistant polyurethanes. It is a low-viscosity liquid with a week but specific odour. This product is available in Germany, Sw...展开 Wannate IPDI is a cycloaliphatic diisocyanate and as such a prefered raw material for the the synthesis of lightstable and water-risistant polyurethanes. It is a low-viscosity liquid with a week but specific odour. This product is available in Germany, Switzerland, Austria, Benelux, UK and Korea. 收起 | Request Sample |
