| CF1-141 | NuSil Silicone Technology 1 | CF1-141 is a high technology silicone primer that is specially formulated to be used with platinum-cured systems and is colored red to provide an easy visual determination of surface coverage. It is a lower Volatile Organic Component (VOC) product and air...展开 CF1-141 is a high technology silicone primer that is specially formulated to be used with platinum-cured systems and is colored red to provide an easy visual determination of surface coverage. It is a lower Volatile Organic Component (VOC) product and air dries. This primer improves adhesion of addition-cured systems to various substrates such as glass, metals, plastics, ceramics and other silicone materials. 收起 | |
| CF1-3800 | NuSil Silicone Technology 1 | CF1-3800 is a thermally conductive, fluorosilicone elastomer that cures at room temperature, or rapidly with the addition of heat. It can be used to adhere covers on housings, modules, and other configurations that require a non-flowable material. This pr...展开 CF1-3800 is a thermally conductive, fluorosilicone elastomer that cures at room temperature, or rapidly with the addition of heat. It can be used to adhere covers on housings, modules, and other configurations that require a non-flowable material. This product can also be utilized as an adhesive, sealant or molding material when solvent resistance is needed. It can provide the transfer of heat between electrical components and heat sinks, and can operate at a temperature range of -65°C to 225°C (-85°F to 437°F). 收起 | |
| CF2-135 | NuSil Silicone Technology 1 | CF2-135 is a silicone primer that is specifically designed to be used with platinum-cured systems where conventional primers will not be sufficient. This product will help to improve the adhesion of addition-cured systems to various substrates such as woo...展开 CF2-135 is a silicone primer that is specifically designed to be used with platinum-cured systems where conventional primers will not be sufficient. This product will help to improve the adhesion of addition-cured systems to various substrates such as wood, metals, ceramics, plastics, and other silicone materials. For the best bonding results, be sure that the surface being primed is clean and degreased. 收起 | |
| CF5-3521-2 | NuSil Silicone Technology 1 | CF5-3521-2 is a two part, 50 mole % fluorosilicone that has a 1:1 Mix Ratio (Part A:B). It can be cured at room temperature, or more rapidly by heating it in an oven or with a heating lamp. The product is especially useful as a coating, sealant, adhesive ...展开 CF5-3521-2 is a two part, 50 mole % fluorosilicone that has a 1:1 Mix Ratio (Part A:B). It can be cured at room temperature, or more rapidly by heating it in an oven or with a heating lamp. The product is especially useful as a coating, sealant, adhesive or molding material in applications that require solvent resistance. 收起 | |
| CF6-135 | NuSil Silicone Technology 1 | CF6-135 is a one-component, high technology silicone primer that is translucent to preserve visibility with translucent products. It is specially designed to be used with platinum cured systems where conventional primers are insufficient. This product wil...展开 CF6-135 is a one-component, high technology silicone primer that is translucent to preserve visibility with translucent products. It is specially designed to be used with platinum cured systems where conventional primers are insufficient. This product will improve the adhesion of addition-cured systems to many different substrates such as glass, metals, plastics, ceramics and other silicone material. 收起 | |
| CV-1161 | NuSil Silicone Technology 1 | CV-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid and particulate contaminants. It can be used in applications that require low outgassing and minimal volatile condesable materials. This ...展开 CV-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid and particulate contaminants. It can be used in applications that require low outgassing and minimal volatile condesable materials. This product is ideal for adhering and bonding silicone elastomers, metals, paper, glass, fabric organics rubbers, some synthetics, and films such as polyester or kapton. 收起 | |
| CV-1500 | NuSil Silicone Technology 1 | CV-1500 is a one part, black, electrically conductive RTV silicone adhesive/sealant that can be used for RFI and EMI shielding in electrical and space applications that require static dissipation. It can also protect components from extremes in temperatur...展开 CV-1500 is a one part, black, electrically conductive RTV silicone adhesive/sealant that can be used for RFI and EMI shielding in electrical and space applications that require static dissipation. It can also protect components from extremes in temperature, humidity, radiation, thermal and mechanical stress. This adhesive is well suited for form-in-place conductive gaskets and attaching heating coils to solar collector plates. 收起 | |
| CV-2500 | NuSil Silicone Technology 1 | CV-2500 is a strong silicone based adhesive that is made to handle extreme conditions in space applications including condensation, humidity, radiation, and both mechanical and thermal stress. It can also be an adhesive in applications that involve solar ...展开 CV-2500 is a strong silicone based adhesive that is made to handle extreme conditions in space applications including condensation, humidity, radiation, and both mechanical and thermal stress. It can also be an adhesive in applications that involve solar cell arrays where clarity and low volatility is needed. 收起 | |
| CV-2566 | NuSil Silicone Technology 1 | CV-2566 is a flowable silicone adhesive that has a broad operating temperature range. The primary use for this product is to be used for applications that require low outgassing and helps eliminate condensation in sensitive devices. In space and electroni...展开 CV-2566 is a flowable silicone adhesive that has a broad operating temperature range. The primary use for this product is to be used for applications that require low outgassing and helps eliminate condensation in sensitive devices. In space and electronic applications, it can be utilized as a sealant or adhesive to help control high vacuum environments. 收起 | |
| CV-2567 | NuSil Silicone Technology 1 | CV-2567 is a pourable RTV siicone that can be used as a diluent for reducing the viscosity of other controlled volatility silicones. This product meets the ASTM 595 low outgas specifications outlined in NASA and the European Space Agency. It can be used a...展开 CV-2567 is a pourable RTV siicone that can be used as a diluent for reducing the viscosity of other controlled volatility silicones. This product meets the ASTM 595 low outgas specifications outlined in NASA and the European Space Agency. It can be used as an adhesive or sealant for electronic and space applications. 收起 | |
| CV-2568 | NuSil Silicone Technology 1 | CV-2568 is a thixotropic RTV silicone that has a low density and has controlled volatility. This product act as a bonding or sealant in space applications. It has a broad operating temperature range and can provide radiation resistance, oxidation and ther...展开 CV-2568 is a thixotropic RTV silicone that has a low density and has controlled volatility. This product act as a bonding or sealant in space applications. It has a broad operating temperature range and can provide radiation resistance, oxidation and thermal stability. It can also be utilized in applications that require low outgassing under extreme operating conditions. 收起 | |
| CV-2900 | NuSil Silicone Technology 1 | CV-2900 is a non-corrosive silicone adhesive that is designed for enhanced performance in extreme low and high temperatures. It can be used as a bond and sealant for applications such as overhead or vertical joints that require a non-slumping and one-part...展开 CV-2900 is a non-corrosive silicone adhesive that is designed for enhanced performance in extreme low and high temperatures. It can be used as a bond and sealant for applications such as overhead or vertical joints that require a non-slumping and one-part material. It can also be utilized as an adhesive , caulking or potting material in electronics/space applications that require minimal outgassing and provides protection from condensation in sensitive devices. 收起 | |
| CV-2943 | NuSil Silicone Technology 1 | CV-2943 is a thermally conductive RTV silicone that has controlled volatility and is designed for enhanced performance in extreme high or low temperatures. It can be used for applications that require low outgassing and minimal volatile condensables under...展开 CV-2943 is a thermally conductive RTV silicone that has controlled volatility and is designed for enhanced performance in extreme high or low temperatures. It can be used for applications that require low outgassing and minimal volatile condensables under extreme operating conditions. This product is also utilized as an adhesive for openings in housings or modules where grooves and other configurations require a limited flow material. 收起 | |
| CV2-1142 | NuSil Silicone Technology 1 | CV2-1142 is a non-corrosive, non-slumping, translucent RTV silicone adhesive/sealant that has controlled volatility. It can be used in applications that require low outgassing under extreme operating conditions. This product is useful for sealing and bond...展开 CV2-1142 is a non-corrosive, non-slumping, translucent RTV silicone adhesive/sealant that has controlled volatility. It can be used in applications that require low outgassing under extreme operating conditions. This product is useful for sealing and bonding in applications such as overhead or vertical joints that require a non-slumping, one-part material. It can also be utilized as a sealant, caulking, adhesive or potting material in space and electrical applications that require minimal outgassing. 收起 | |
| CV2-1161 | NuSil Silicone Technology 1 | CV2-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid particulate contaminants. It is able to withstand normal pressure variations as well as high temperature exposure. This product is ideal...展开 CV2-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid particulate contaminants. It is able to withstand normal pressure variations as well as high temperature exposure. This product is ideal for bonding and adhering silicone elastomers, paper, metals, glass, fabric, films, and some synthetics. It can also be used for applications that require low outgassing and minimal volatile condensable materials. 收起 | |
| CV3-2500 | NuSil Silicone Technology 1 | CV3-2500 is an optically clear silicone that is has controlled volatility. It is an ideal product for applications that require a low viscosity to create a superior flow and low outgassing. This is how it helps keep condensation from affecting sensitive d...展开 CV3-2500 is an optically clear silicone that is has controlled volatility. It is an ideal product for applications that require a low viscosity to create a superior flow and low outgassing. This is how it helps keep condensation from affecting sensitive devices. It can also be utilized as an adhesive for projects involving solar arrays. 收起 | |
| CV4-1161-5 | NuSil Silicone Technology 1 | CV4-1161-5 is a one-part, double-sided pressure sensitive adhesive tape that is best used to adhere and bond metals, paper, glass, fabric, organic rubbers, synthetics and films. It has the ability to collect dust in and around sensitive electronic compone...展开 CV4-1161-5 is a one-part, double-sided pressure sensitive adhesive tape that is best used to adhere and bond metals, paper, glass, fabric, organic rubbers, synthetics and films. It has the ability to collect dust in and around sensitive electronic components and is designed to withstand extreme temperature/pressure variations. 收起 | |
| CV4-2289-1 | NuSil Silicone Technology 1 | CV4-2289-1 is a thixotropic silicone elastomer that can be used as an adhesive that offers superior tear strength. This silicone also demonstrates flexibility at extremely low temperatures with a stiffening temperature of approximately -115°C. It can be u...展开 CV4-2289-1 is a thixotropic silicone elastomer that can be used as an adhesive that offers superior tear strength. This silicone also demonstrates flexibility at extremely low temperatures with a stiffening temperature of approximately -115°C. It can be used to protect electronic components, cable harness breakouts, seals, and gaskets from harsh environmental conditions. 收起 | |
| CV7-1142-1 | NuSil Silicone Technology 1 | CV7-1142-1 is a non corrosive material that has a white color and it is a non-slumping silicone RTV. It can be used as a caulking, adhesive or sealant that protects sensitive circuits, connectors and switches in space applications. This product has a broa...展开 CV7-1142-1 is a non corrosive material that has a white color and it is a non-slumping silicone RTV. It can be used as a caulking, adhesive or sealant that protects sensitive circuits, connectors and switches in space applications. This product has a broad operating temperature range so it can withstand hot and cold conditions. It also can be used for sealing openings in modules or housings where grooves or other configurations require a non-flowable to limited flow material. 收起 | |
| EPM-2420 | NuSil Silicone Technology 1 | EPM-2420 is a general purpose silicone adhesive that has a low volatility and a 1:1 Mix Ratio (Part A: Part B). The primary function of this adhesive is to protect electric components and assemblies against vibration, shock, dust, moisture, chemicals and ...展开 EPM-2420 is a general purpose silicone adhesive that has a low volatility and a 1:1 Mix Ratio (Part A: Part B). The primary function of this adhesive is to protect electric components and assemblies against vibration, shock, dust, moisture, chemicals and other hazards. It is also ideal for applications where a low viscosity and clarity are important. 收起 | |
| EPM-2890 | NuSil Silicone Technology 1 | EPM-2890 is a one part, white, silicone adhesive that is thermally conductive and non corrosive. It has the ability to operate on a wide temperature range and provide moderate heat transfer between electrical components and their heat sinks. This product ...展开 EPM-2890 is a one part, white, silicone adhesive that is thermally conductive and non corrosive. It has the ability to operate on a wide temperature range and provide moderate heat transfer between electrical components and their heat sinks. This product can also function as a caulking, sealing, potting or adhesive material in electronics applications that require minimal outgassing to prevent condensation from building in sensitive devices. 收起 | |
| FS-3730-2 | NuSil Silicone Technology 1 | FS-3730-2 is a black adhesive/sealant that is based on a fluorosilicone polymer with 100 mole % fluorosilicone. It can be utilized to bond or protect hardware components that are exposed to aviation fuels or gasoline. This product can also be used for sea...展开 FS-3730-2 is a black adhesive/sealant that is based on a fluorosilicone polymer with 100 mole % fluorosilicone. It can be utilized to bond or protect hardware components that are exposed to aviation fuels or gasoline. This product can also be used for sealing or bonding applications requiring fuel and/or solvent resistance. Another strong property is that it bonds aggressively to most surfaces. 收起 | |
| FS1-3730 | NuSil Silicone Technology 1 | FS1-3730 is an adhesive/sealant that is translucent and based on a 100 mole % fluorosilicone polymer. This product can be utilized for sealing and bonding applications that require solvent and/or fuel resistance. It is a very strong product and will bond ...展开 FS1-3730 is an adhesive/sealant that is translucent and based on a 100 mole % fluorosilicone polymer. This product can be utilized for sealing and bonding applications that require solvent and/or fuel resistance. It is a very strong product and will bond aggressively to most surfaces. 收起 | |
| FS3-3730 | NuSil Silicone Technology 1 | FS3-3730 is a translucent, one-part, adhesive/sealant that has 100 mole % flouorosilicone. It is strong and will bond aggressively to most surfaces. This product can be utilized for bonding and sealing applications that require solven and/or fuel resistan...展开 FS3-3730 is a translucent, one-part, adhesive/sealant that has 100 mole % flouorosilicone. It is strong and will bond aggressively to most surfaces. This product can be utilized for bonding and sealing applications that require solven and/or fuel resistance. It can also be used for protecting or bonding hardware components that have been exposed to gasoline or aviation fuels. 收起 | |
| Polyester Modified Silicon Resin SM1072A | Jiangsu Sanmu Group Corporation 江苏三木集团有限公司 | SM1072A is a polyester modified silicone resin. It has high-low temperature resistance and hydrophobic moisture resistance, as well as good weather resistance and chemical resistance. After fully curing, the hardness is ≥ 5H, with high gloss, fullness and...展开 SM1072A is a polyester modified silicone resin. It has high-low temperature resistance and hydrophobic moisture resistance, as well as good weather resistance and chemical resistance. After fully curing, the hardness is ≥ 5H, with high gloss, fullness and yellowing resistance. SM1072A can be widely used in heat resisting coatings, used as a basic resin for non-stick coatings and special coatings for frying pans, electric cookers, ovens, stoves, toasters, electric irons, kitchen ventilators, and gas stoves. 收起 | |
| PSA-1170 | NuSil Silicone Technology 1 | PSA-1170 is a one-part, non-curing, pressure sensitive silicone adhesive that has a translucent appearance and a low viscosity. It can be used for temporarily adhering to various substrates such as silicone, glass, metals, and organic rubbers. PSA-1170 is...展开 PSA-1170 is a one-part, non-curing, pressure sensitive silicone adhesive that has a translucent appearance and a low viscosity. It can be used for temporarily adhering to various substrates such as silicone, glass, metals, and organic rubbers. PSA-1170 is supplied in flammable solvents so it needs to be handled cautiously. Allow solvent to evaporate before adhering or attaching adhesive-coated objects together. 收起 | |
| R-1008-0 | NuSil Silicone Technology 1 | R-1008-0 is a translucent, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating mus...展开 R-1008-0 is a translucent, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 收起 | |
| R-1008-1 | NuSil Silicone Technology 1 | R-1008-1 is a white, RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating t...展开 R-1008-1 is a white, RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F).This product can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. 收起 | |
| R-1008-2 | NuSil Silicone Technology 1 | R-1008-2 is a black RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion, and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating t...展开 R-1008-2 is a black RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion, and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F).This product can be used on silicone rubber parts as a marking ink where the coating must maintain long term stability. 收起 | |
| R-1008-8 | NuSil Silicone Technology 1 | R-1008-8 is a violet, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must mai...展开 R-1008-8 is a violet, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 收起 | |
| R-1130 | NuSil Silicone Technology 1 | R-1130 is a non-corrosive, rapid curing, nun-slumping RTV silicone adhesive that can be used as a coating for semi-conductors and integrated circuits. It can also be utilized as an adhesive/sealant for electrical wires, terminals, mounting resistors and ...展开 R-1130 is a non-corrosive, rapid curing, nun-slumping RTV silicone adhesive that can be used as a coating for semi-conductors and integrated circuits. It can also be utilized as an adhesive/sealant for electrical wires, terminals, mounting resistors and connectors. It is ideal for overhead or side wall applications due to its non-slumping characteristics. 收起 | |
| R-1140 | NuSil Silicone Technology 1 | R-1140 is a one part, translucent, non-slumping silicone adhesive that is supplied in ready to use Semco® cartridges. This product bonds aggressively to most surfaces including glass, ceramics, metals, natural and synthetic fibers, wood, painted surfaces ...展开 R-1140 is a one part, translucent, non-slumping silicone adhesive that is supplied in ready to use Semco® cartridges. This product bonds aggressively to most surfaces including glass, ceramics, metals, natural and synthetic fibers, wood, painted surfaces and other silicone rubbers. It is best used for applications that require an operating temperature rang of 65 to 240°C (-85 to 465°F). 收起 | |
| R-2100-1 | NuSil Silicone Technology 1 | R-2100-1 is a white silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...展开 R-2100-1 is a white silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2100-2 | NuSil Silicone Technology 1 | R-2100-2 is a black silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...展开 R-2100-2 is a black silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2100-3 | NuSil Silicone Technology 1 | R-2100-3 is a red silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal ...展开 R-2100-3 is a red silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2100-6 | NuSil Silicone Technology 1 | R-2100-6 is a green silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...展开 R-2100-6 is a green silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2145 | NuSil Silicone Technology 1 | R1-2145 is an extremely tough gray silicone adhesive that does not require atmospheric moisture to cure and the product is available in easy to use, airless side by side kits that eliminate mixing and deairing. It rapidly cures at room temperature by appl...展开 R1-2145 is an extremely tough gray silicone adhesive that does not require atmospheric moisture to cure and the product is available in easy to use, airless side by side kits that eliminate mixing and deairing. It rapidly cures at room temperature by applying heat in an oven or a heat gun or lamp. This adhesive can be used for bonding and sealing silicones to each other and other substrates such as metals and plastics. It is ready for rapid production or prototyping due to the a rapid cure. 收起 | |
| R-2634 | NuSil Silicone Technology 1 | R-2634 is a two-part, electrically conductive RTV silicone that is designed for enhanced performance in extreme high and low temperatures. It can be used as an adhesive to bond covers on housings or where grooves and other configurations require a non-flo...展开 R-2634 is a two-part, electrically conductive RTV silicone that is designed for enhanced performance in extreme high and low temperatures. It can be used as an adhesive to bond covers on housings or where grooves and other configurations require a non-flowable material. This product is especially useful for sealing formed-in-place conductive gaskets and grounding connections. It can also be used for EMI and RFI shielding for aerospace and electrical applications. 收起 | |
| R-2949 | NuSil Silicone Technology 1 | R-2949 is a two-part, white, thermally conductive silicone that can cure rapidly with the addition of heat. It is an ideal product to be used in applications that require protection against extreme low and high temperatures. It can be used as an adhesive ...展开 R-2949 is a two-part, white, thermally conductive silicone that can cure rapidly with the addition of heat. It is an ideal product to be used in applications that require protection against extreme low and high temperatures. It can be used as an adhesive to bond openings in housings and modules where grooves or other configurations require a limited flow material with moderate thermal conductivity. It can also provide the transfer of heat between electrical components and their heat sinks. 收起 | |
| R-3930 | NuSil Silicone Technology 1 | R-3930 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It is designed for spraying, dip casting, and RTV curing of thin elastomeric films. It can also be utilized for...展开 R-3930 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It is designed for spraying, dip casting, and RTV curing of thin elastomeric films. It can also be utilized for bonding, coating, and sealing applications that require solvent and/or fuel resistance. It bonds aggressively to most surfaces and can help minimize ice adhesion. 收起 | |
| R-3975 | NuSil Silicone Technology 1 | R-3975 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It can be utilized for bonding, coating, and sealing applications that require solvent and/or fuel resistance. ...展开 R-3975 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It can be utilized for bonding, coating, and sealing applications that require solvent and/or fuel resistance. It bonds aggressively to most surfaces and can help minimize ice adhesion. It is designed for spraying, dip casting, and RTV curing of thin elastomeric films. 收起 | |
| R1-2145 | NuSil Silicone Technology 1 | R1-2145 is an extremely tough gray silicone adhesive that rapidly cures at room temperature by applying heat in an oven or a heat gun or lamp. It does not require atmospheric moisture to cure and the product is available in easy to use, airless side by si...展开 R1-2145 is an extremely tough gray silicone adhesive that rapidly cures at room temperature by applying heat in an oven or a heat gun or lamp. It does not require atmospheric moisture to cure and the product is available in easy to use, airless side by side kits that eliminate mixing and deairing, This adhesive can be used for bonding and sealing silicones to each other and other substrates such as metals and plastics. It is ready for rapid production or prototyping due to the a rapid cure. 收起 | |
| R1-3930-11 | NuSil Silicone Technology 1 | R1-3930-11 is a gray fluorosilicone, adhesive, sealant, and coating that bonds aggressively to most surfaces. This product can be utilized for sealing, coating, and bonding applications that require solvent and/or fuel resistance. It can also be used for ...展开 R1-3930-11 is a gray fluorosilicone, adhesive, sealant, and coating that bonds aggressively to most surfaces. This product can be utilized for sealing, coating, and bonding applications that require solvent and/or fuel resistance. It can also be used for bonding or protecting hardware components exposed to gasoline or aviation fuels. It can be further dispersed for spraying applications. 收起 | |
| R3-2160 | NuSil Silicone Technology 1 | R3-2160 is a two-part, pourable silicone system that has a high tear strength and good physical properties. It is designed for enhance performance in extreme high and low temperatures. The ideal use for this high temperature adhesive/sealant is for pottin...展开 R3-2160 is a two-part, pourable silicone system that has a high tear strength and good physical properties. It is designed for enhance performance in extreme high and low temperatures. The ideal use for this high temperature adhesive/sealant is for potting connectors, seals and gaskets, molded high voltage terminals, and cable harness breakouts. 收起 | |
| R3-3930-11 | NuSil Silicone Technology 1 | R3-3930-11 is a gray, two-part, RTV silicone that can be further dispersed for spraying applications. It has strong physical attributes which make it bond aggressively to most surfaces. It can also be utilized in applications where coating, sealing, and ...展开 R3-3930-11 is a gray, two-part, RTV silicone that can be further dispersed for spraying applications. It has strong physical attributes which make it bond aggressively to most surfaces. It can also be utilized in applications where coating, sealing, and bonding are necessary for fuel and /or solvent resistance.This product can be used to bond or protect hardware components that are exposed to gasoline or aviation fuels. 收起 | |
| R31-2186 | NuSil Silicone Technology 1 | R31-2186 is a translucent, thixotropic, silicone adhesive that has a high tear strength and cures at room temperature, and rapidly with the addition of heat. The consistency of this product allows it to be supplied in easy-to-use, airless side-by-side kit...展开 R31-2186 is a translucent, thixotropic, silicone adhesive that has a high tear strength and cures at room temperature, and rapidly with the addition of heat. The consistency of this product allows it to be supplied in easy-to-use, airless side-by-side kits that remove the need to mix. It can be used as an adhesive for sealing and bonding silicones to each other and other substrates such as plastics and metals. 收起 | |
| R32-2186 | NuSil Silicone Technology 1 | R32-2186 is a two-part, translucent, thixotropic, high tear strength silicone adhesive that cures rapidly with the application of heat in an oven, or by a heat gun or lamp. It does not require atmospheric moisture to cure. This adhesive can be used for bo...展开 R32-2186 is a two-part, translucent, thixotropic, high tear strength silicone adhesive that cures rapidly with the application of heat in an oven, or by a heat gun or lamp. It does not require atmospheric moisture to cure. This adhesive can be used for bonding and sealing silicones to each other and other substrates such as metals and plastics. This product is ready for rapid production or prototyping due to its rapid cure rate. 收起 | |
| R33-2186 | NuSil Silicone Technology 1 | R33-2183 is a fast-curing silicone adhesive that cures at room temperature, or rapidly with the use of heat in an oven, or a heat gun lamp. It does not require atmospheric moisture to cure. This product can be used as an adhesive for sealing and bonding s...展开 R33-2183 is a fast-curing silicone adhesive that cures at room temperature, or rapidly with the use of heat in an oven, or a heat gun lamp. It does not require atmospheric moisture to cure. This product can be used as an adhesive for sealing and bonding silicones to each other and other substrates such as metals and plastics. It is best used for applications requiring an operating temperature range of –65°C to 240°C (-85 to 465°F). 收起 | |
| R4-1140 | NuSil Silicone Technology 1 | R4-1140 is a one-part, self leveling, solvent-free silicone adhesive that cures at room temperature upon exposure to atmospheric moisture. This product bonds aggressively to many surfaces including ceramics, metals, glass, synthetic and natural fibers, wo...展开 R4-1140 is a one-part, self leveling, solvent-free silicone adhesive that cures at room temperature upon exposure to atmospheric moisture. This product bonds aggressively to many surfaces including ceramics, metals, glass, synthetic and natural fibers, wood, painted surfaces, many plastics and other silicone rubbers. 收起 | |
| SCV-2590 | NuSil Silicone Technology 1 | SCV-2590 is a two-part, clear silicone elastomer that can be used as an adhesive in low strength applications such as solar cell arrays where clarity, and a low volatility are needed. In electronic and space applications it can prevent condensation from b...展开 SCV-2590 is a two-part, clear silicone elastomer that can be used as an adhesive in low strength applications such as solar cell arrays where clarity, and a low volatility are needed. In electronic and space applications it can prevent condensation from building in sensitive devices. This product also features Ultra Low OutgassingTM which exceeds specifications outlined in NASA and the European Space Agency. 收起 | |
| SCV-2590-2 | NuSil Silicone Technology 1 | SCV-2590-2 is a black silicone that has low viscosity and can be utilized as an adhesive in optical applications requiring a black material to block light. This product offers a broad operating temperature range and can be used to protect electronic assem...展开 SCV-2590-2 is a black silicone that has low viscosity and can be utilized as an adhesive in optical applications requiring a black material to block light. This product offers a broad operating temperature range and can be used to protect electronic assemblies from extreme temperatures, humidity and radiation. It also features Ultra Low OutgassingTM which makes it ideal to protect sensitive devices from condensation. 收起 | |
| SCV1-2590 | NuSil Silicone Technology 1 | SCV1-2590 is an optically clear silicone system with low viscosity and is a suitable adhesive in applications such as solar cell arrays, where clarity and low volatility are important. It can also be used in space and electric applications that require lo...展开 SCV1-2590 is an optically clear silicone system with low viscosity and is a suitable adhesive in applications such as solar cell arrays, where clarity and low volatility are important. It can also be used in space and electric applications that require low outgassing to avoid condensation in sensitive devices. 收起 | |
| SCV1-2596 | NuSil Silicone Technology 1 | SCV1-2596 is an electrically conductive silicone adhesive/sealant that features Ultra Low OutgassingTM. It can be utilized in applications that require minimal volatile condensables under extreme operating conditions. This product can also be used for RFI...展开 SCV1-2596 is an electrically conductive silicone adhesive/sealant that features Ultra Low OutgassingTM. It can be utilized in applications that require minimal volatile condensables under extreme operating conditions. This product can also be used for RFI and EMI shielding in electrical and space applications and is well suited to for form-in-place conductive gaskets. 收起 | |
| SP-120 | NuSil Silicone Technology 1 | SP-120 is a silicone primer that is formulated for use with one and two-part RTV systems, and does not need mixing.The translucent color of SP-120 helps to preserve visibility with other translucent products. This primer will also improve the adhesion of ...展开 SP-120 is a silicone primer that is formulated for use with one and two-part RTV systems, and does not need mixing.The translucent color of SP-120 helps to preserve visibility with other translucent products. This primer will also improve the adhesion of the RTV systems to other substrates such as metals, ceramics, glass, and wood. 收起 | |
| SP-121 | NuSil Silicone Technology 1 | SP-121 is a specially formulated silicone primer that is designed to be used with one and two-part RTV systems. This primer is red in color and provides an easy visual determination of surface coverage when using it. It will also improve the adhesion of t...展开 SP-121 is a specially formulated silicone primer that is designed to be used with one and two-part RTV systems. This primer is red in color and provides an easy visual determination of surface coverage when using it. It will also improve the adhesion of the RTV systems to various substrates such as glass, metals, rigid plastics, and ceramics. 收起 | |
| SP-124 | NuSil Silicone Technology 1 | SP-124 is a silicone primer that is designed for use with condensation cured systems where conventional silicone primers are ineffective. This product will help to improve the adhesion of one and two-part condensation cured systems to various substrates s...展开 SP-124 is a silicone primer that is designed for use with condensation cured systems where conventional silicone primers are ineffective. This product will help to improve the adhesion of one and two-part condensation cured systems to various substrates such as glass, ceramics, metal, rigid plastics, wood and some composites. It can be applied by wiping, brushing or dipping a uniform thin film onto the substrates. 收起 | |
| SP-142 | NuSil Silicone Technology 1 | SP-142 is a translucent silicone primer that is specially designed to be used with platinum-cured systems on polycarbonates. This one-component primer is supplied in VM&P Naphtha and requires no mixing. When brushed, wiped, or dipped on a polycarbonate, i...展开 SP-142 is a translucent silicone primer that is specially designed to be used with platinum-cured systems on polycarbonates. This one-component primer is supplied in VM&P Naphtha and requires no mixing. When brushed, wiped, or dipped on a polycarbonate, it will help improve the adhesion with addition-cured systems. 收起 | |
| SP-270 | NuSil Silicone Technology 1 | SP-270 is a silicone primer that was specifically designed for use with platinum-cured systems where other conventional primers are insufficient. It is a one-component primer supplied in VM&P Naphtha so it requires no mixing at all. When applied to additi...展开 SP-270 is a silicone primer that was specifically designed for use with platinum-cured systems where other conventional primers are insufficient. It is a one-component primer supplied in VM&P Naphtha so it requires no mixing at all. When applied to addition-cured systems with iridite coated materials, it will improve the adhesion. This also holds true with other substrates including glass, metals, some plastics and other silicone materials. 收起 | |
| SP1-204 | NuSil Silicone Technology 1 | SP1-204 is a specially formulated translucent primer that is designed for use with one and two-part RTV systemts. This primer requires no mixing and air dries. It is an ideal product to help improve the adhesion of one and two-part systems to various subs...展开 SP1-204 is a specially formulated translucent primer that is designed for use with one and two-part RTV systemts. This primer requires no mixing and air dries. It is an ideal product to help improve the adhesion of one and two-part systems to various substrates such as glass, metals, plastics, ceramics and wood. 收起 | |
| STANLUX® Gold 12000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 12000 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 1...展开 STANLUX® Gold 12000 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 12000 is available in several shades and has an average size of 16 microns. 收起 | |
| STANLUX® Gold 13000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 13000 is a fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for use in flexographic and gravure systems. STANLUX® Gold 13...展开 STANLUX® Gold 13000 is a fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for use in flexographic and gravure systems. STANLUX® Gold 13000 is available in several shades and has an average size of 16 microns. 收起 | |
| STANLUX® Gold 13300 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 13300 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 1...展开 STANLUX® Gold 13300 is a fine bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment offers opacity, gloss and printability for flexographic and gravure systems. STANLUX® Gold 13300 is available in several shades and has an average size of 12 microns. 收起 | |
| STANLUX® Gold 14000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 14000 is super fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment generates decorative metallic effects and is used in offset printing inks. STANLUX® Gold 14000 i...展开 STANLUX® Gold 14000 is super fine bronze powder constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment generates decorative metallic effects and is used in offset printing inks. STANLUX® Gold 14000 is available in several shades and has an average size of 5 microns. 收起 | |
| STANLUX® Gold 2000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2000 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...展开 STANLUX® Gold 2000 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2000 is available in several shades and has an average size of 50 microns. 收起 | |
| STANLUX® Gold 2100 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2100 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...展开 STANLUX® Gold 2100 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2100 is available in several shades and has an average size of 50 microns. 收起 | |
| STANLUX® Gold 2700 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2700 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...展开 STANLUX® Gold 2700 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2700 is available in several shades and has an average size of 45 microns. 收起 | |
| STANLUX® Gold 2800 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 2800 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...展开 STANLUX® Gold 2800 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 2800 is available in several shades and has an average size of 45 microns. 收起 | |
| STANLUX® Gold 3500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 3500 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...展开 STANLUX® Gold 3500 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 3500 is available in several shades and has an average size of 35 microns. 收起 | |
| STANLUX® Gold 3600 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 3600 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is r...展开 STANLUX® Gold 3600 is a coarse bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in decorative paints and is recommended for applications where high brilliance is required. STANLUX® Gold 3600 is available in several shades and has an average size of 35 microns. 收起 | |
| STANLUX® Gold 4500 (Shade D) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints, and silk screen inks, and it is rec...展开 STANLUX® Gold 4500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints, and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4500 has an average size of 30 microns and a 8% water retention rate with a 3.4 - 4.2 (cm²/g Min) water coverage property. 收起 | |
| STANLUX® Gold 4600 (Shade C) | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 4600 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...展开 STANLUX® Gold 4600 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where high brilliance and hiding power are required. STANLUX® Gold 4600 has an average size of 30 microns and a 1.5% water retention rate with a 3.4 - 4.2 (cm²/g Min) water coverage property. 收起 | |
| STANLUX® Gold 5500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 5500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...展开 STANLUX® Gold 5500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where regular surface finish and hiding power are required. STANLUX® Gold 5500 is available in several shades and has an average size of 23 microns. It possesses a 0.5% water retention rate with a 4.2 - 6.0 (cm²/g Min) water coverage property. 收起 | |
| STANLUX® Gold 6500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 6500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...展开 STANLUX® Gold 6500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where regular surface finish and hiding power are required. STANLUX® Gold 6500 is available in several shades and has an average size of 20 microns. It possesses a 5% water retention rate with a 5.5 - 6.5 (cm²/g Min) water coverage property. 收起 | |
| STANLUX® Gold 7500 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Gold 7500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is reco...展开 STANLUX® Gold 7500 is a bronze powder pigment constituted by lamellar particles of copper, zinc and aluminium alloys covered with stearic acid. This pigment is used in aerosol spray decorative paints, decorative paints and silk screen inks, and it is recommended for applications where regular surface finish and hiding power are required. STANLUX® Gold 7500 is available in several shades and has an average size of 18 microns. It possesses a 0.8% water retention rate with a 6.3 - 7.5 (cm²/g Min) water coverage property. 收起 | |
| STANLUX® Hydro 140 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Hydro 140 is a stabilized aluminium leafing paste with medium-coarse lamellar particles, recommended for use in waterborne paints. This product has a maximum retention of 1% in # 325 mesh. | |
| STANLUX® Hydro 150 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Hydro 150 is a stabilized aluminium leafing paste with medium-coarse lamellar particles, recommended for use in waterborne paints. This product has a maximum retention of 4% in # 325 mesh. | |
| STANLUX® Paste 1130 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1130 is a non-leafing type aluminum paste made of fine lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1130 is specially recommended for use in ...展开 STANLUX® Paste 1130 is a non-leafing type aluminum paste made of fine lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1130 is specially recommended for use in decorative paints, industrial paints, maintenance, protective and marine coatings, and trade paints. It has an average particle size of 11 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) 收起 | |
| STANLUX® Paste 120 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 120 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 120 commonly used for general industrial...展开 STANLUX® Paste 120 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 120 commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 17 microns and a minimum water coverage of 20,000 cm2/g. 收起 | |
| STANLUX® Paste 130N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 130N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 130N is specially recommended for applic...展开 STANLUX® Paste 130N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 130N is specially recommended for application in formulations based on resins that are incompatible with aliphatic solvents and is commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 19 microns and a minimum water coverage of 21,000 cm2/g. 收起 | |
| STANLUX® Paste 140 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 140 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 140 is recommended for application in for...展开 STANLUX® Paste 140 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. This product has a high leafing value that adds a durable and protective property to paints. STANLUX® Paste 140 is recommended for application in formulations that require aluminium pigment with high metallic effect and is commonly used for general industrial paints, decorative and/or architectural paints, and maintenance paints. It has an average particle size of 19 microns and a minimum water coverage of 21,000 cm2/g. 收起 | |
| STANLUX® Paste 1600 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1600 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600 is considered to be standard level and is...展开 STANLUX® Paste 1600 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600 is considered to be standard level and is recommended for paint formulations that require aluminium pigment with high metallic effect including: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. It has an average particle size of 23 microns and uses a combined solvent of MS (Mineral Spirit) and HA (High Aromatic.) 收起 | |
| STANLUX® Paste 1600N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1600N is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600N is considered to be standard level and ...展开 STANLUX® Paste 1600N is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1600N is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 23 microns and uses a HA (High Aromatic) solvent. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. 收起 | |
| STANLUX® Paste 166 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 166 is a leafing type aluminum paste made of medium size lamellar particles covered with stearic acid. STANLUX® Paste 166 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paint...展开 STANLUX® Paste 166 is a leafing type aluminum paste made of medium size lamellar particles covered with stearic acid. STANLUX® Paste 166 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paints, industrial paints, and trade paints. It has an average particle size of 15 microns and a minimum water coverage of 22,000cm2/g. 收起 | |
| STANLUX® Paste 1700 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1700 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1700 is considered to be standard level and is...展开 STANLUX® Paste 1700 is a non-leafing type aluminum paste made of lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1700 is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 21 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. 收起 | |
| STANLUX® Paste 1770 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1770 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770 is considered to be standard level...展开 STANLUX® Paste 1770 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770 is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 16 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. 收起 | |
| STANLUX® Paste 1770/60 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1770/60 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770/60 is considered to be standard...展开 STANLUX® Paste 1770/60 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1770/60 is considered to be standard level and is recommended for formulation systems with low tolerance to aliphatic solvent. It has an average particle size of 16 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. STANLUX® Paste 1770/60 has the same characteristics of Stanlux Paste 1770 with 60% of solids. Applications include: aerosol spray decorative paints, industrial paints, maintenance paints, protective and marine coatings, and trade paints. 收起 | |
| STANLUX® Paste 1870 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 1870 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1870 is considered to be standard level...展开 STANLUX® Paste 1870 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 1870 is considered to be standard level and is recommended for systems requiring differentiated metallic finishes, brighter color, and high hiding power. It has an average particle size of 16 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: aerosol spray decorative paints, industrial paints, and trade paints. 收起 | |
| STANLUX® Paste 200 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 200 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paints, trade pai...展开 STANLUX® Paste 200 is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200 is recommended for application in high grade and brilliant protective paints and is commonly used for decorative paints, trade paints, and printing inks. It has an average particle size of 14 microns and a minimum water coverage of 20,000 cm2/g. 收起 | |
| STANLUX® Paste 2000 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 2000 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 2000 is considered to be standard level...展开 STANLUX® Paste 2000 is a non-leafing type aluminum paste made of medium lamellar particles covered with oleic acid that provides differentiated effects that add a metallic shine to the applied system. STANLUX® Paste 2000 is considered to be standard level and is recommended for systems requiring differentiated metallic effects, and brighter metallic pigment. It has an average particle size of 21 microns and uses a HA (High Aromatic) and MS (Mineral Spirit) solvent. Applications include: decorative paints, industrial paints, and trade paints. 收起 | |
| STANLUX® Paste 200N | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 200N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200N is recommended for application in products requiring high covering power and is commonly used for decorative paints, trade paint...展开 STANLUX® Paste 200N is a leafing type aluminum paste made of lamellar particles covered with stearic acid. STANLUX® Paste 200N is recommended for application in products requiring high covering power and is commonly used for decorative paints, trade paints, and printing inks. It has an average particle size of 14 microns and a minimum water coverage of 20,000 cm2/g. 收起 | |
| STANLUX® Paste 260 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 260 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 260 is specially recommended for printing inks and is commonly used for aerosol spray decorative paints, flexographic printing in...展开 STANLUX® Paste 260 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 260 is specially recommended for printing inks and is commonly used for aerosol spray decorative paints, flexographic printing inks, and gravure printing inks. It has an average particle size of 14 microns and a minimum water coverage of 28,000 cm2/g. 收起 | |
| STANLUX® Paste 266 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 266 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 266 is specially recommended for high grade and brilliant printing inks and is commonly used for aerosol spray decorative paints,...展开 STANLUX® Paste 266 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 266 is specially recommended for high grade and brilliant printing inks and is commonly used for aerosol spray decorative paints, flexographic and gravure printing inks that require aluminium pigment with a high metallic effect. It has an average particle size of 14 microns and a minimum water coverage of 28,000 cm2/g. 收起 | |
| STANLUX® Paste 270/70 IPA | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 270/70 IPA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 270/70 IPA is specially recomme...展开 STANLUX® Paste 270/70 IPA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 270/70 IPA is specially recommended for printing inks and is commonly used for flexography and gravure free of residual solvent odour. It has an average particle size of 11 microns and a minimum water coverage of 30,000 cm2/g. 收起 | |
| STANLUX® Paste 280 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 280 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 280 is specially recommended for high grade printing inks and is commonly used for aerosol spray decorative paints, flexographic ...展开 STANLUX® Paste 280 is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid. STANLUX® Paste 280 is specially recommended for high grade printing inks and is commonly used for aerosol spray decorative paints, flexographic and gravure printing inks that require aluminium pigment with a high metallic effect. It has an average particle size of 12 microns and a minimum water coverage of 34,000 cm2/g. 收起 | |
| STANLUX® Paste 290 60EA | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 290 60EA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 290 60EA is specially recommended f...展开 STANLUX® Paste 290 60EA is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is suitable with solvent for high grade printing inksthat require low odour property. STANLUX® Paste 290 60EA is specially recommended for printing inks and is commonly used for flexography and gravure free of residual solvent odour. It has an average particle size of 9 microns and a minimum water coverage of 45,000 cm2/g. 收起 | |
| STANLUX® Paste 290 60MO | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 290 60MO is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is formulated for high-grade offset printing inks. STANLUX® Paste 290 60MO is specially recommended for printing inks and is commonly u...展开 STANLUX® Paste 290 60MO is a leafing type aluminum paste made of fine lamellar particles covered with stearic acid and is formulated for high-grade offset printing inks. STANLUX® Paste 290 60MO is specially recommended for printing inks and is commonly used for offset printing ink free of residual solvent odour. It has an average particle size of 9 microns and a minimum water coverage of 45,000 cm2/g. 收起 | |
| STANLUX® Paste 340 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Paste 340 is a leafing type aluminum paste made of coarse lamellar particles covered with stearic acid that provide a reflection effect or barrier protection. STANLUX® Paste 340 is specially recommended for printing inks and is commonly used for ...展开 STANLUX® Paste 340 is a leafing type aluminum paste made of coarse lamellar particles covered with stearic acid that provide a reflection effect or barrier protection. STANLUX® Paste 340 is specially recommended for printing inks and is commonly used for maintenance, protective and marine coatings, and roof coatings. It has an average particle size of 21 microns and a minimum water coverage of 9,000 cm2/g. 收起 | |
| STANLUX® Pell Gold 130 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Pell Gold 130 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to appl...展开 STANLUX® Pell Gold 130 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to applied systems. STANLUX® Pell Gold 130 is available is several shades and is recommended for use in flexographic and gravure printing inks. 收起 | |
| STANLUX® Pell Gold 131 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Pell Gold 131 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to appl...展开 STANLUX® Pell Gold 131 is a fine bronze powder pigment in pellet form, that disperses in solvents like ethyl acetate or ethyl alcohol and eliminates dust during handling. It has an average particle size of 16 microns and provides opacity and gloss to applied systems. STANLUX® Pell Gold 130 is recommended for use in flexographic and gravure printing inks. 收起 | |
| STANLUX® Silver 3201 | Aldoro Indústria de Pós e Pigmentos Metálicos Ltda | STANLUX® Silver 3201 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX®...展开 STANLUX® Silver 3201 is a non-leafing type aluminium pigment with narrowly curved lamellar particle distribution that presents a metallic effect and is recommended in formulations that require a coarse aluminium pigment with high metallic effect. STANLUX® Silver 3201 has an average particle size of 29 microns and can be used in auto parts paints, automotive paints (original and refinish), plastic coatings, and printing inks. 收起 |
