| Additive ST2/14 | Ichemco | Additive ST2/14 is a polycondensed urethane solution in toluene/xylene. This product is most commonly used as an ink additive to increase printability in PP acrylic and solvent-based pressure sensitive adhesive tape applications. | |
| Additive ST2/14 ECO | Ichemco | Additive ST2/14 ECO is a polycondensed urethane solution in aliphatic solvents. This product is most commonly used as an ink additive to increase printability in PP acrylic and solvent-based pressure sensitive adhesive tape applications. | |
| Bitoner® C5 Resin BT-2104 | Qingdao Bater Chemical Co., Ltd. | Bitoner® C5 Resin BT-2104, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin obtained from petroleum-derived monomers. It has good compatibility with a wide range of polymers, good thermal stability, low wa...view more Bitoner® C5 Resin BT-2104, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin obtained from petroleum-derived monomers. It has good compatibility with a wide range of polymers, good thermal stability, low wax cloud point, low odor, and water resistance. BT-2104 has recommended applications in solvent based PSA, sealants, coatings, hot melt adhesives, and HMPSA. view less | |
| Bitoner® C9 Resin BP-100 | Qingdao Bater Chemical Co., Ltd. | Bitoner® C9 Resin BP-100, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with SAS, EVA, and other polymers, good thermal resistance, low...view more Bitoner® C9 Resin BP-100, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with SAS, EVA, and other polymers, good thermal resistance, low odor, low VOC, and water resistance. BP-100 has recommended applications in sealants, shoe adhesives, rubber, coatings, and hot melt adhesives. view less | |
| Bitoner® C9 Resin BP-120 | Qingdao Bater Chemical Co., Ltd. | Bitoner® C9 Resin BP-120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with resins and polymers, good thermal resistance, low odor, lo...view more Bitoner® C9 Resin BP-120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with resins and polymers, good thermal resistance, low odor, low VOC, and water resistance. BP-120 has recommended applications in sealants, solvent based adhesives, rubber, coatings, printing ink, and hot melt adhesives. view less | |
| Bitoner® C9 Resin BP-140 | Qingdao Bater Chemical Co., Ltd. | Bitoner® C9 Resin BP-140, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with resins and polymers, good thermal resistance, low odor, lo...view more Bitoner® C9 Resin BP-140, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with resins and polymers, good thermal resistance, low odor, low VOC, and water resistance. BP-140 has recommended applications in sealants, solvent based adhesives, rubber, coatings, PSA, asphalt modification, printing ink, and hot melt adhesives. view less | |
| Bitoner® C9 Resin BP-150 | Qingdao Bater Chemical Co., Ltd. | Bitoner® C9 Resin BP-150, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin. It has good compatibility with rosin modified phenolic resins, water resistance, and recommended applications in sealants, solvent...view more Bitoner® C9 Resin BP-150, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin. It has good compatibility with rosin modified phenolic resins, water resistance, and recommended applications in sealants, solvent based adhesives, rubber, coatings, PSA, printing ink, and hot melt adhesives. view less | |
| Bitoner® H-100 | Qingdao Bater Chemical Co., Ltd. | Bitoner® H-100, in the form of a white granular, is thermoplastic hydrogenated aromatic resin obtained from petroleum-derived monomers. It has good thermal resistance, low odor, water resistance, and good compatibility with SBS, SIS, and EVA. H-100 has re...view more Bitoner® H-100, in the form of a white granular, is thermoplastic hydrogenated aromatic resin obtained from petroleum-derived monomers. It has good thermal resistance, low odor, water resistance, and good compatibility with SBS, SIS, and EVA. H-100 has recommended applications in solvent adhesives, plastic modification, hot melt adhesives, and wax modification. view less | |
| Bitoner® Hydrogenated C9 Resins H-120 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Hydrogenated C9 Resins H-120, in the form of a white granular, is thermoplastic hydrogenated aromatic resin obtained from petroleum-derived monomers. It has good thermal resistance, low odor, water resistance, and good compatibility with SBS, SIS...view more Bitoner® Hydrogenated C9 Resins H-120, in the form of a white granular, is thermoplastic hydrogenated aromatic resin obtained from petroleum-derived monomers. It has good thermal resistance, low odor, water resistance, and good compatibility with SBS, SIS, and EVA. H-120 has recommended applications in solvent adhesives, hot melt adhesives, and wax modification. view less | |
| Bitoner® Resin BA-120 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin BA-120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with other polymers and resins, good thermal resistance, water res...view more Bitoner® Resin BA-120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aromatic resin obtained from petroleum-derived monomers. It has good compatibility with other polymers and resins, good thermal resistance, water resistance, low odor, and very low VOC. BA-120 has recommended applications in sealants, rubber, coatings, printing ink, hot melt adhesive, and solvent based adhesives. view less | |
| Bitoner® Resin BT-100 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin BT-100, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin. It has good chemical stability, water resistance, good affinity with a wide range of fillers, and has recommended applications in th...view more Bitoner® Resin BT-100, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin. It has good chemical stability, water resistance, good affinity with a wide range of fillers, and has recommended applications in thermoplastic road marking paints, rubber, sealants, and hot melt adhesives. view less | |
| Bitoner® Resin BT-1102 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin BT-1102, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin. It has good chemical stability, water resistance, good affinity with a wide range of fillers, and has recommended applications in t...view more Bitoner® Resin BT-1102, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin. It has good chemical stability, water resistance, good affinity with a wide range of fillers, and has recommended applications in thermoplastic road marking paints, coatings, sealants, and hot melt adhesives. view less | |
| Bitoner® Resin BT-1200H | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin BT-1200H, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin obtained from petroleum-derived monomers. It has good compatibility with APAO, NR, and other polymers, good thermal stability, low ...view more Bitoner® Resin BT-1200H, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin obtained from petroleum-derived monomers. It has good compatibility with APAO, NR, and other polymers, good thermal stability, low odor, low volatility, and water resistance. BT-1200H has recommended applications in sealants, wax modifications, asphalt modification, rubber, coatings, and hot melt adhesives. view less | |
| Bitoner® Resin BT-2110 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin BT-2110, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin obtained from petroleum-derived monomers. It has good compatibility with polymers and SIS, low wax cloud point, good thermal stabili...view more Bitoner® Resin BT-2110, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, aliphatic resin obtained from petroleum-derived monomers. It has good compatibility with polymers and SIS, low wax cloud point, good thermal stability, low odor, low volatility, and water resistance. BT-2104 has recommended applications in solvent based PSA, sealants, coatings, hot melt adhesives, and HMPSA. view less | |
| Bitoner® Resin C-2120 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin C-2120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, modified C5 hydrocarbon resin. It has good heat stability, low odor, good compatibility, and solubility in various solvents. C-2120 has recommended a...view more Bitoner® Resin C-2120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, modified C5 hydrocarbon resin. It has good heat stability, low odor, good compatibility, and solubility in various solvents. C-2120 has recommended applications in hot melt adhesives, sealants, solvent based PSA, HMPSA, and coatings. view less | |
| Bitoner® Resin C-2125 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin C-2125, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, modified C5 hydrocarbon resin. It has good heat stability, low odor, good compatibility, and solubility in various solvents. C-2120 has recommended a...view more Bitoner® Resin C-2125, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, modified C5 hydrocarbon resin. It has good heat stability, low odor, good compatibility, and solubility in various solvents. C-2120 has recommended applications in hot melt adhesives, sealants, solvent based PSA, HMPSA, and coatings. view less | |
| Bitoner® Resin C2130 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin C2130, in the form of a slightly yellow granular, is low molecular weight, C9 modified C5 hydrocarbon resin. It has low odor, low volatility, good heat stability, good compatibility, and recommended applications in sealants, coatings, hot m...view more Bitoner® Resin C2130, in the form of a slightly yellow granular, is low molecular weight, C9 modified C5 hydrocarbon resin. It has low odor, low volatility, good heat stability, good compatibility, and recommended applications in sealants, coatings, hot melt adhesives, PSA, and rubber compounds. view less | |
| Bitoner® Resin DH-1110 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin DH-1110, in the form of a white granular, is a thermoplastic resin obtained from hydrogenation and polymerization of cyclic ingredients such as derived monomers. It has good heat stability, good initial color, low VOC, water resistance, and...view more Bitoner® Resin DH-1110, in the form of a white granular, is a thermoplastic resin obtained from hydrogenation and polymerization of cyclic ingredients such as derived monomers. It has good heat stability, good initial color, low VOC, water resistance, and good compatibility. DH-1110 has recommended applications in hot melt adhesives, sealants, pressure sensitive adhesives, and wax modifications. view less | |
| Bitoner® Resin LH-3100 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin LH-3100, in the form of a water white granular, is hydrogenated C9 hydrocarbon resin. It has good heat stability, good chemical stability, odorless, low VOC, and good compatibility with various polymers. LH-3100 has recommended applications...view more Bitoner® Resin LH-3100, in the form of a water white granular, is hydrogenated C9 hydrocarbon resin. It has good heat stability, good chemical stability, odorless, low VOC, and good compatibility with various polymers. LH-3100 has recommended applications in sealants, coatings, ink, pressure sensitive adhesives, and hot melt adhesives. view less | |
| Bitoner® Resin TR-100 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin TR-100, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, C9 and C5 co-polymerized resin. It has low odor, low volatility, good heat stability, good compatibility, water resistance, and has recommended appli...view more Bitoner® Resin TR-100, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, C9 and C5 co-polymerized resin. It has low odor, low volatility, good heat stability, good compatibility, water resistance, and has recommended applications in sealants, coatings, hot melt adhesives, PSA, and rubber compounds. view less | |
| Bitoner® Resin TR-120 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin TR-120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, modified C9 hydrocarbon resin. . It has low odor, low volatility, good heat stability, good compatibility, water resistance, and has recommended appl...view more Bitoner® Resin TR-120, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, modified C9 hydrocarbon resin. . It has low odor, low volatility, good heat stability, good compatibility, water resistance, and has recommended applications in sealants, coatings, hot melt adhesives, PSA, and rubber compounds. view less | |
| Bitoner® Resin TR-2080 | Qingdao Bater Chemical Co., Ltd. | Bitoner® Resin TR-2080, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, C9 and C5 co-polymerized resin. It has low odor, low volatility, good heat resistance, good compatibility, water resistance, and has recommended app...view more Bitoner® Resin TR-2080, in the form of a slightly yellow granular, is thermoplastic, low molecular weight, C9 and C5 co-polymerized resin. It has low odor, low volatility, good heat resistance, good compatibility, water resistance, and has recommended applications in sealants, coatings, hot melt adhesives, PSA, and rubber compounds. view less | |
| Blendex 31 | Ichemco | Blendex 31 is a solvent-based, heat sealable adhesive. This product has a total solids content of 21-23% and a Brookfield viscosity at 25°C of 400-1000 cPs. Blendex 31 is most commonly used to bond rubber compounds to metal and polymeric substrates. | |
| Blendex 55 F | Ichemco | Blendex 55 F is a solvent-free, one-component moisture curing polyurethane adhesive. This product has a viscosity at 100°C of 750-1000 mPa.s. Blendex 55 F is most commonly used in fabric and film lamination applications. | |
| Blendex 70 A | Ichemco | Blendex 70 A is a monocomponent polyurethane adhesive in solvent phase (Ethyl Acetate). solvent-based, heat sealable adhesive. This product has a total solids content of 64-66% and a Brookfield viscosity at 25°C of 670-870 cPs. Blendex 70 A is most common...view more Blendex 70 A is a monocomponent polyurethane adhesive in solvent phase (Ethyl Acetate). solvent-based, heat sealable adhesive. This product has a total solids content of 64-66% and a Brookfield viscosity at 25°C of 670-870 cPs. Blendex 70 A is most commonly used as a solvent adhesive in coating system applications. view less | |
| Blendex 75 A | Ichemco | Blendex 75 A is a monocomponent polyurethane adhesive in solvent phase (Ethyl Acetate) solvent-based, heat sealable adhesive. This product has a total solids content of 74-76% and a Brookfield viscosity at 25°C of 3300-5300 cPs. Blendex 75 A is most comm...view more Blendex 75 A is a monocomponent polyurethane adhesive in solvent phase (Ethyl Acetate) solvent-based, heat sealable adhesive. This product has a total solids content of 74-76% and a Brookfield viscosity at 25°C of 3300-5300 cPs. Blendex 75 A is most commonly used as a solvent adhesive in coating system applications. view less | |
| Blendex 81 T | Ichemco | Blendex 81 T is a a two-component polyurethane adhesive in ethyl acetate, solvent-based, heat sealable adhesive. This product has a total solids content of 58-62% and a Brookfield viscosity at 25°C of 2300-4300 cPs. Blendex 81 T is most commonly used in f...view more Blendex 81 T is a a two-component polyurethane adhesive in ethyl acetate, solvent-based, heat sealable adhesive. This product has a total solids content of 58-62% and a Brookfield viscosity at 25°C of 2300-4300 cPs. Blendex 81 T is most commonly used in film and fabric lamination applications. view less | |
| Blendex B1 | Ichemco | Blendex B1 is a liquid blend of synthetic polymers and natural resins. This product has a viscosity at 3500-8000 cPa. Blendex B1 is most commonly used in solvent adhesive production applications. | |
| Blendex S 24/20 | Ichemco | Blendex S 24/20 is a thermoplastic polyurethane in methyl-ethyl-ketone solution, solvent-based, heat sealable adhesive. This product has a total solids content of 20-22% and a Brookfield viscosity at 25°C of 5500-7500 cPs. Blendex S 24/20 is most commonl...view more Blendex S 24/20 is a thermoplastic polyurethane in methyl-ethyl-ketone solution, solvent-based, heat sealable adhesive. This product has a total solids content of 20-22% and a Brookfield viscosity at 25°C of 5500-7500 cPs. Blendex S 24/20 is most commonly used as a soft heat sealable adhesive in lamination applications. view less | |
| Blendex S 24/25 A | Ichemco | Blendex S 24/25 A is a solution of a thermoplastic polyurethane in acetone solvent-based, heat sealable adhesive. This product has a total solids content of 24-26% and a Brookfield viscosity at 25°C of 5000-7000 cPs. Blendex S 24/25 A is most commonly us...view more Blendex S 24/25 A is a solution of a thermoplastic polyurethane in acetone solvent-based, heat sealable adhesive. This product has a total solids content of 24-26% and a Brookfield viscosity at 25°C of 5000-7000 cPs. Blendex S 24/25 A is most commonly used as a soft heat sealable adhesive in lamination applications. view less | |
| Blendex S 24/25 MA | Ichemco | Blendex S 24/25 MA is a mat solution of a thermoplastic polyurethane in acetone, solvent-based, heat sealable adhesive. This product has a total solids content of 23-25%. Blendex S 24/25 MA is most commonly used as a soft heat sealable adhesive in lamina...view more Blendex S 24/25 MA is a mat solution of a thermoplastic polyurethane in acetone, solvent-based, heat sealable adhesive. This product has a total solids content of 23-25%. Blendex S 24/25 MA is most commonly used as a soft heat sealable adhesive in lamination applications. view less | |
| Blendex S 79 | Ichemco | Blendex S 79 is a solvent-based, heat sealable adhesive. This product has a total solids content of 29-31% and a Brookfield viscosity at 25°C of 4500-10,500 mPa.s. Blendex S 79 is most commonly used in fabric, paper, and plastic film direct coating applic...view more Blendex S 79 is a solvent-based, heat sealable adhesive. This product has a total solids content of 29-31% and a Brookfield viscosity at 25°C of 4500-10,500 mPa.s. Blendex S 79 is most commonly used in fabric, paper, and plastic film direct coating applications. view less | |
| Blendex S 79 T | Ichemco | Blendex S 79 T is a solvent-based, heat sealable adhesive. This product has a total solids content of 33-35% and a Brookfield viscosity at 25°C of 5000-15,000 mPa.s. Blendex S 79 T is most commonly used in fabric, paper, and plastic film direct and transf...view more Blendex S 79 T is a solvent-based, heat sealable adhesive. This product has a total solids content of 33-35% and a Brookfield viscosity at 25°C of 5000-15,000 mPa.s. Blendex S 79 T is most commonly used in fabric, paper, and plastic film direct and transfer coating applications. view less | |
| Blendex S12 20 | Ichemco | Blendex S12 20 is a thermoplastic polyurethane in methyl-ethyl-ketone solution, solvent-based, heat sealable adhesive. This product has a total solids content of 19-21% and a Brookfield viscosity at 25°C of 2000-6000 cPs. Blendex S12 20 is most commonly...view more Blendex S12 20 is a thermoplastic polyurethane in methyl-ethyl-ketone solution, solvent-based, heat sealable adhesive. This product has a total solids content of 19-21% and a Brookfield viscosity at 25°C of 2000-6000 cPs. Blendex S12 20 is most commonly used as a soft heat sealable adhesive in lamination applications. view less | |
| Blendex Seal 81 DH | Ichemco | Blendex Seal 81 DH is a water-based, heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 50-200 mPa.s. Blendex Seal 81 DH is most commonly used as a heat sealable elastic adhesive in leather, fo...view more Blendex Seal 81 DH is a water-based, heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 50-200 mPa.s. Blendex Seal 81 DH is most commonly used as a heat sealable elastic adhesive in leather, foam, woven, non-woven, and synthetic leather applications. view less | |
| Blendex Seal 81 DH (V1) | Ichemco | Blendex Seal 81 DH (V1) is a water dispersion of vinyl-acrylic copolimers and slightly tacky additives heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 12,000-17,000 mPa.s. Blendex Seal 81 D...view more Blendex Seal 81 DH (V1) is a water dispersion of vinyl-acrylic copolimers and slightly tacky additives heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 12,000-17,000 mPa.s. Blendex Seal 81 DH (V1) is most commonly used as a heat sealable elastic adhesive in leather, foam, woven, non-woven, and synthetic leather applications. view less | |
| Blendex Seal 81 DH (V2) | Ichemco | Blendex Seal 81 DH (V2) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 17,000-27,000 mPa.s. Blendex Seal 81 DH (V2) is most commonly used as a heat sealable elastic adhesi...view more Blendex Seal 81 DH (V2) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 17,000-27,000 mPa.s. Blendex Seal 81 DH (V2) is most commonly used as a heat sealable elastic adhesive in leather, foam, woven, non-woven, and synthetic leather applications. view less | |
| Blendex Seal 81 DH (V3) | Ichemco | Blendex Seal 81 DH (V3) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 27,000-37,000 mPa.s. Blendex Seal 81 DH (V3) is most commonly used as a heat sealable elastic adhesi...view more Blendex Seal 81 DH (V3) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50%, and a Brookfield viscosity at 25°C of 27,000-37,000 mPa.s. Blendex Seal 81 DH (V3) is most commonly used as a heat sealable elastic adhesive in leather, foam, woven, non-woven, and synthetic leather applications. view less | |
| Blendex Seal C6 | Ichemco | Blendex Seal C6 is a water-based, heat sealable adhesive. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 7500-10,500 mPa.s. Blendex Seal C6 is most commonly used as a soft heat sealable adhesive in leather, foam, f...view more Blendex Seal C6 is a water-based, heat sealable adhesive. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 7500-10,500 mPa.s. Blendex Seal C6 is most commonly used as a soft heat sealable adhesive in leather, foam, fabric, non-woven, and synthetic leather applications. view less | |
| Blendex Seal C6 (V3) | Ichemco | Blendex Seal C6 (V3) is a a water dispersion of polyvinylacetate/maleate copolymer, stabilised with synthetic and cellulosic stabilisers, heat sealable adhesive. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 27,00...view more Blendex Seal C6 (V3) is a a water dispersion of polyvinylacetate/maleate copolymer, stabilised with synthetic and cellulosic stabilisers, heat sealable adhesive. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 27,000-37,000 mPa.s. Blendex Seal C6 (V3) is most commonly used as a soft heat sealable adhesive in leather, foam, fabric, non-woven, and synthetic leather applications. view less | |
| Blendex Seal DH 14 | Ichemco | Blendex Seal DH 14 is a polyester based, aliphatic acqueous polyurethane dispersion, water-based, heat sealable adhesive. This product has a total solids content of 29-31%. Blendex Seal DH 14 is most commonly used as a heat sealable adhesive in textile ap...view more Blendex Seal DH 14 is a polyester based, aliphatic acqueous polyurethane dispersion, water-based, heat sealable adhesive. This product has a total solids content of 29-31%. Blendex Seal DH 14 is most commonly used as a heat sealable adhesive in textile applications. view less | |
| Blendex Seal DH 70 | Ichemco | Blendex Seal DH 70 is a water-based, heat sealable adhesive based on modified acrylic polymers. This product has a total solids content of 23-25% and a Brookfield viscosity at 25°C of 8000-16,000 mPa.s. Blendex Seal DH 70 is most commonly used as a heat s...view more Blendex Seal DH 70 is a water-based, heat sealable adhesive based on modified acrylic polymers. This product has a total solids content of 23-25% and a Brookfield viscosity at 25°C of 8000-16,000 mPa.s. Blendex Seal DH 70 is most commonly used as a heat sealable adhesive in fabric, non-woven, leather, foam, and synthetic leather applications. view less | |
| Blendex Seal DH 76 | Ichemco | Blendex Seal DH 76 is a water-based, heat sealable adhesive, formulated with modified acrylic co-polymers.. This product has a total solids content of 37.5-39.5% and a Brookfield viscosity at 25°C of 1000-1500 mPa.s. Blendex Seal DH 76 is most commonly us...view more Blendex Seal DH 76 is a water-based, heat sealable adhesive, formulated with modified acrylic co-polymers.. This product has a total solids content of 37.5-39.5% and a Brookfield viscosity at 25°C of 1000-1500 mPa.s. Blendex Seal DH 76 is most commonly used as a heat sealable elastic adhesive in woven, non-woven, leather, foam, and synthetic leather applications. view less | |
| Blendex Seal DH 8 | Ichemco | Blendex Seal DH 8 is a water-based, heat sealable adhesive based on a modified acrylic polymer. This product has a total solids content of 52-54%, and a Brookfield viscosity at 25°C of 2000-5000 mPa.s. Blendex Seal DH 8 is most commonly used as a heat s...view more Blendex Seal DH 8 is a water-based, heat sealable adhesive based on a modified acrylic polymer. This product has a total solids content of 52-54%, and a Brookfield viscosity at 25°C of 2000-5000 mPa.s. Blendex Seal DH 8 is most commonly used as a heat sealable adhesive in fabric, leather, foam, non-woven, and synthetic leather applications. view less | |
| Blendex Seal DH 8 M | Ichemco | Blendex Seal DH 8 M is a water-based, heat sealable adhesive based on a modified acrylic polymer. This product has a total solids content of 46-50% and a Brookfield viscosity at 25°C of 3000-6500 mPa.s. Blendex Seal DH 8 M is most commonly used as a heat ...view more Blendex Seal DH 8 M is a water-based, heat sealable adhesive based on a modified acrylic polymer. This product has a total solids content of 46-50% and a Brookfield viscosity at 25°C of 3000-6500 mPa.s. Blendex Seal DH 8 M is most commonly used as a heat sealable adhesive in fabric, non-woven, leather, foam, and synthetic leather applications. view less | |
| Blendex Seal DH 8 M (V2) | Ichemco | Blendex Seal DH 8 M (V2) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50% and a Brookfield viscosity at 25°C of 17,000-27,000 mPa.s. Blendex Seal DH 8 M (V2) is most commonly used as a heat sealable adhesive in f...view more Blendex Seal DH 8 M (V2) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50% and a Brookfield viscosity at 25°C of 17,000-27,000 mPa.s. Blendex Seal DH 8 M (V2) is most commonly used as a heat sealable adhesive in fabric, non-woven, leather, foam, and synthetic leather applications. view less | |
| Blendex Seal DH 8 M (V3) | Ichemco | Blendex Seal DH 8 M (V3) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50% and a Brookfield viscosity at 25°C of 27,000-37,000 mPa.s. Blendex Seal DH 8 M (V3) is most commonly used as a heat sealable adhesive in f...view more Blendex Seal DH 8 M (V3) is a water-based, heat sealable adhesive. This product has a total solids content of 46-50% and a Brookfield viscosity at 25°C of 27,000-37,000 mPa.s. Blendex Seal DH 8 M (V3) is most commonly used as a heat sealable adhesive in fabric, non-woven, leather, foam, and synthetic leather applications. view less | |
| Blendex WUM | Ichemco | Blendex WUM is a water-based, synthetic latex heat sealable adhesive. This product has a total solids content of 39-41% and a Brookfield viscosity at 25°C of 1000-3000 mPa.s. Blendex WUM is most commonly used as a remoistable adhesive in paper and cardboa...view more Blendex WUM is a water-based, synthetic latex heat sealable adhesive. This product has a total solids content of 39-41% and a Brookfield viscosity at 25°C of 1000-3000 mPa.s. Blendex WUM is most commonly used as a remoistable adhesive in paper and cardboard applications. view less | |
| Ithane 02 | Ichemco | Ithane 02 is an aromatic thermoplastic polyurethane in a dry granule form. This product has a Brookfield viscosity at 25°C of 460-680 cPs. Ithane 02 is most commonly used in shoe adhesive applications. | |
| Ithane 15/25 | Ichemco | Ithane 15/25 is a solvent-based, heat sealable adhesive. This product has a total solids content of 24-26%. Ithane 15/25 is most commonly used as a soft heat sealable adhesive in lamination applications. | |
| Ithane 46 | Ichemco | Ithane 46 is a solvent-based, heat sealable adhesive. This product has a total solids content of 35-37% and a Brookfield viscosity at 25°C of 1000-2000 cPs. Ithane 46 is most commonly used in transparent and aluminum-containing structure lamination applic...view more Ithane 46 is a solvent-based, heat sealable adhesive. This product has a total solids content of 35-37% and a Brookfield viscosity at 25°C of 1000-2000 cPs. Ithane 46 is most commonly used in transparent and aluminum-containing structure lamination applications. view less | |
| Release K 100 Q | Ichemco | Release K 100 Q is a synthetic resin blend. This product has a total solids content of 99-100%. Release K 100 Q is most commonly used as a release agent in polyolephinic self-adhesive tape applications. | |
| Release ST8 Dry | Ichemco | Release ST8 Dry is a synthetic resin-based compound. This product has a total solids content of 98-100%. Release ST8 Dry is most commonly used as a release coat in corona-treated polyolephynic backing adhesive tape applications. | |
| Release ST9 HM Dry | Ichemco | Release ST9 HM Dry is a synthetic resin-based compound. This product has a total solids content of 99-100%. Release ST9 HM Dry is most commonly used as a release coat in toluene or hexane/isopropyl alcohol-soluble corona-treated polyolephynic backing adhe...view more Release ST9 HM Dry is a synthetic resin-based compound. This product has a total solids content of 99-100%. Release ST9 HM Dry is most commonly used as a release coat in toluene or hexane/isopropyl alcohol-soluble corona-treated polyolephynic backing adhesive tape applications. view less | |
| S.L. A 20 | Ichemco | S.L. A 20 is an APEO-free, water dispersion of acrylic copolymers. This product has a total solids content of 44-46% and a Brookfield viscosity at 25°C of less than 300 cPs. S.L. A 20 is most commonly used as a binder in water gloss enamel, primer, and ...view more S.L. A 20 is an APEO-free, water dispersion of acrylic copolymers. This product has a total solids content of 44-46% and a Brookfield viscosity at 25°C of less than 300 cPs. S.L. A 20 is most commonly used as a binder in water gloss enamel, primer, and clear varnish applications. view less | |
| S.L. AU 11 | Ichemco | S.L. AU 11 is a self crosslinking acrylic copolymer emulsion. This product has a total solids content of 37-39% and a Brookfield viscosity at 25°C of less than 300 cPs. S.L. AU 11 is most commonly used in transparent wood floor varnish production applicat...view more S.L. AU 11 is a self crosslinking acrylic copolymer emulsion. This product has a total solids content of 37-39% and a Brookfield viscosity at 25°C of less than 300 cPs. S.L. AU 11 is most commonly used in transparent wood floor varnish production applications. view less | |
| Solacril 105 ACP | Ichemco | Solacril 105 ACP is a solventborne, solvent-based pressure sensitive adhesive. This product has a total solids content of 49-51%, has a tack of 2-5 cm, and has a peel of 2500-3000 g/in. Solacril 105 ACP is most commonly used in the production of protectiv...view more Solacril 105 ACP is a solventborne, solvent-based pressure sensitive adhesive. This product has a total solids content of 49-51%, has a tack of 2-5 cm, and has a peel of 2500-3000 g/in. Solacril 105 ACP is most commonly used in the production of protective films for plastic and metal surfaces, as well as removable tapes and labels. view less | |
| Solacril 2010 | Ichemco | Solacril 2010 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 53-57% and a peel of 1200-1600 g/in. Solacril 2010 is most commonly used in industrial pressure sensitive adhesive tape and decal produc...view more Solacril 2010 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 53-57% and a peel of 1200-1600 g/in. Solacril 2010 is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. view less | |
| Solacril 203 | Ichemco | Solacril 203 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 38-42% and a peel of 600-800 g/in. Solacril 203 is most commonly used in protective film applications. | |
| Solacril 204 | Ichemco | Solacril 204 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 49-51%, has a tack of 1-3 cm, and a peel of 500-800 g/in. Solacril 204 is most commonly used in protective film applications. | |
| Solacril 44 | Ichemco | Solacril 44 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 49-51%, has a tack of greater than 20 cm, and a peel of 1000-1300 g/in. Solacril 44 is most commonly used in plastic, paper, polyurethane ...view more Solacril 44 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 49-51%, has a tack of greater than 20 cm, and a peel of 1000-1300 g/in. Solacril 44 is most commonly used in plastic, paper, polyurethane foam, fabric, and leather substrate applications. view less | |
| Solacril 44 D | Ichemco | Solacril 44 D is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 34-36%, has a tack of 3-9 cm, and a peel of 950-1450 g/in. Solacril 44 D is most commonly used in plastic, paper, polyurethane foam, fab...view more Solacril 44 D is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 34-36%, has a tack of 3-9 cm, and a peel of 950-1450 g/in. Solacril 44 D is most commonly used in plastic, paper, polyurethane foam, fabric, and leather substrate applications. view less | |
| Solacril 55 MED | Ichemco | Solacril 55 MED is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 38-42%, has a tack of 3-5 cm, and a peel of 1700-1900 g/in. Solacril 55 MED is most commonly used in plastic, paper, polyurethane foam...view more Solacril 55 MED is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 38-42%, has a tack of 3-5 cm, and a peel of 1700-1900 g/in. Solacril 55 MED is most commonly used in plastic, paper, polyurethane foam, fabric, and leather substrate applications. view less | |
| Solacril 701 | Ichemco | Solacril 701 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 42-44% and a peel of 2000-2400 g/in. Solacril 701 is most commonly used in plastic film as well as paper, polyurethane foam, fabric, and ...view more Solacril 701 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 42-44% and a peel of 2000-2400 g/in. Solacril 701 is most commonly used in plastic film as well as paper, polyurethane foam, fabric, and leather substrate applications. view less | |
| Solacril 744 | Ichemco | Solacril 744 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 48-52%, has a tack of 5-10 cm, and has a peel of 900-1100 g/in. Solacril 744 is most commonly used in industrial pressure sensitive adhes...view more Solacril 744 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 48-52%, has a tack of 5-10 cm, and has a peel of 900-1100 g/in. Solacril 744 is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. view less | |
| Solacril 744 AS | Ichemco | Solacril 744 AS is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 38-42%, has a tack of 3-8 cm, and has a peel of 900-1200 g/in. Solacril 744 AS is most commonly used in industrial pressure sensitive ...view more Solacril 744 AS is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 38-42%, has a tack of 3-8 cm, and has a peel of 900-1200 g/in. Solacril 744 AS is most commonly used in industrial pressure sensitive adhesive tape, label, and decal production applications. view less | |
| Solacril 744 D | Ichemco | Solacril 744 D is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 34-36% and a peel of 1100 g/in. Solacril 744 D is most commonly used in industrial pressure sensitive adhesive tape and decal productio...view more Solacril 744 D is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 34-36% and a peel of 1100 g/in. Solacril 744 D is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. view less | |
| Solacril 744 T | Ichemco | Solacril 744 T is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 19-21%, has a tack of 5-10 cm, and has a peel of 850-1100 g/in. Solacril 744 T is most commonly used in industrial pressure sensitive a...view more Solacril 744 T is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 19-21%, has a tack of 5-10 cm, and has a peel of 850-1100 g/in. Solacril 744 T is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. view less | |
| Solacril 758 | Ichemco | Solacril 758 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 49-51%. Solacril 758 is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. | |
| Solacril 758/35 | Ichemco | Solacril 758/35 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 34-36%. Solacril 758/35 is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. | |
| Solacril 758/46 | Ichemco | Solacril 758/46 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 45-47%. Solacril 758/46 is most commonly used in industrial pressure sensitive adhesive tape and decal production applications. | |
| Solacril 957 MED | Ichemco | Solacril 957 MED is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 45-47% and a peel of 1400-1600 g/in. Solacril 957 MED is most commonly used in medical applications. | |
| Solacril SPR 12 M3 | Ichemco | Solacril SPR 12 M3 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 8.5-10.5%. Solacril SPR 12 M3 is most commonly used in spray applications. | |
| Solacril WS 33 | Ichemco | Solacril WS 33 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 29-31%. Solacril WS 33 is most commonly used as a base in finished adhesive applications. | |
| Solacril WS 40 | Ichemco | Solacril WS 40 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 50-52% and a peel of 800-1200 g/in. Solacril WS 40 is most commonly used in single and double-sided tape, as well as water-soluble labe...view more Solacril WS 40 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 50-52% and a peel of 800-1200 g/in. Solacril WS 40 is most commonly used in single and double-sided tape, as well as water-soluble label production applications. view less | |
| Solacril WS 60 | Ichemco | Solacril WS 60 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 50-52% and a peel of 600-900 g/in. Solacril WS 60 is most commonly used in single and double-sided tape, as well as water-soluble label...view more Solacril WS 60 is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 50-52% and a peel of 600-900 g/in. Solacril WS 60 is most commonly used in single and double-sided tape, as well as water-soluble label production applications. view less | |
| Solacril WS 60 AF | Ichemco | Solacril WS 60 AF is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 50-52%. Solacril WS 60 AF is most commonly used in single and double-sided tape, as well as water-soluble label production applicati...view more Solacril WS 60 AF is a solventborne, acrylic-based pressure sensitive adhesive. This product has a total solids content of 50-52%. Solacril WS 60 AF is most commonly used in single and double-sided tape, as well as water-soluble label production applications. view less | |
| Tackifier 15 | Ichemco | Tackifier 15 is a solvent-free, waterborne tackifier dispersion of a mixed alyphatic-aromatic hydrocarbon resin. This product has a total solids content of 49-52% and a Brookfield viscosity at 25°C of 50-1000 mPa.s. Tackifier 15 is most commonly used to...view more Tackifier 15 is a solvent-free, waterborne tackifier dispersion of a mixed alyphatic-aromatic hydrocarbon resin. This product has a total solids content of 49-52% and a Brookfield viscosity at 25°C of 50-1000 mPa.s. Tackifier 15 is most commonly used to enhance adhesive performance in polymeric latex, and adhesive tape and label applications. view less | |
| Tackifier 55 | Ichemco | Tackifier 55 is a solvent-free, waterborne dispersion of modified natural resins. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 400-1000 mPa.s. Tackifier 55 is most commonly used in acrylic, SBR, and NR adhesive m...view more Tackifier 55 is a solvent-free, waterborne dispersion of modified natural resins. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 400-1000 mPa.s. Tackifier 55 is most commonly used in acrylic, SBR, and NR adhesive modification applications. view less | |
| Tackifier 65 | Ichemco | Tackifier 65 is a solvent-free, waterborne tackifier dispersion. This product has a total solids content of 50-54% and a Brookfield viscosity at 25°C of less than 1000 mPa.s. Tackifier 65 is most commonly used to enhance adhesive performance in polymeric ...view more Tackifier 65 is a solvent-free, waterborne tackifier dispersion. This product has a total solids content of 50-54% and a Brookfield viscosity at 25°C of less than 1000 mPa.s. Tackifier 65 is most commonly used to enhance adhesive performance in polymeric latex, as well as self-adhesive tape and label applications. view less | |
| Tackifier 68 | Ichemco | Tackifier 68 is a solvent-free, waterborne dispersion of a stabilized rosin ester. This product has a total solids content of 52-54% and a Brookfield viscosity at 25°C of 200-600 cPs. Tackifier 68 is most commonly used to enhance pressure sensitive proper...view more Tackifier 68 is a solvent-free, waterborne dispersion of a stabilized rosin ester. This product has a total solids content of 52-54% and a Brookfield viscosity at 25°C of 200-600 cPs. Tackifier 68 is most commonly used to enhance pressure sensitive properties in acrylic, SBR, and synthetic water-based polymer adhesive applications. view less | |
| Tackifier 71 | Ichemco | Tackifier 71 is an acrylic aqueous dispersion. This product has a total solids content of 49-51% and a Brookfield viscosity at 25°C of 40-150 mPa.s. Tackifier 71 is most commonly used as a tackifier in water-based acrylic pressure sensitive adhesive produ...view more Tackifier 71 is an acrylic aqueous dispersion. This product has a total solids content of 49-51% and a Brookfield viscosity at 25°C of 40-150 mPa.s. Tackifier 71 is most commonly used as a tackifier in water-based acrylic pressure sensitive adhesive production applications. view less | |
| Tackifier 80 | Ichemco | Tackifier 80 is a solvent-free, waterborne tackifier dispersion. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 100-500 cPs. Tackifier 80 is most commonly used as a tackifier in acrylic polymer-based pressure sensi...view more Tackifier 80 is a solvent-free, waterborne tackifier dispersion. This product has a total solids content of 54-56% and a Brookfield viscosity at 25°C of 100-500 cPs. Tackifier 80 is most commonly used as a tackifier in acrylic polymer-based pressure sensitive adhesive production applications. view less | |
| Tackifier 95 | Ichemco | Tackifier 95 is a solvent-free, waterborne tackifier dispersion. This product has a total solids content of 50-57% and a Brookfield viscosity at 25°C of less than 1000 mPa.s. Tackifier 95 is most commonly used to enhance pressure sensitive properties in p...view more Tackifier 95 is a solvent-free, waterborne tackifier dispersion. This product has a total solids content of 50-57% and a Brookfield viscosity at 25°C of less than 1000 mPa.s. Tackifier 95 is most commonly used to enhance pressure sensitive properties in polymeric latex, as well as self-adhesive tape and label applications. view less | |
| Tackmelt A 34 MED | Ichemco | Tackmelt A 34 MED is a hot melt pressure sensitive adhesive based on SIS synthetic rubber and synthetic resins. This product has a viscosity at 150°C of 7000-10,000 mPa.s and a viscosity at 185°C of 1500-2500 mPa.s. Tackmelt A 34 MED is most commonly used...view more Tackmelt A 34 MED is a hot melt pressure sensitive adhesive based on SIS synthetic rubber and synthetic resins. This product has a viscosity at 150°C of 7000-10,000 mPa.s and a viscosity at 185°C of 1500-2500 mPa.s. Tackmelt A 34 MED is most commonly used in medical applications where skin contact is expected. view less | |
| Tackmelt A 43 MED | Ichemco | Tackmelt A 43 MED is a hot melt pressure sensitive adhesive based on SIS synthetic rubber and synthetic resins. This product has a viscosity at 150°C of 6000-8000 mPa.s and a viscosity at 185°C of 1200-2000 mPa.s. Tackmelt A 43 MED is most commonly used i...view more Tackmelt A 43 MED is a hot melt pressure sensitive adhesive based on SIS synthetic rubber and synthetic resins. This product has a viscosity at 150°C of 6000-8000 mPa.s and a viscosity at 185°C of 1200-2000 mPa.s. Tackmelt A 43 MED is most commonly used in medical applications where skin contact is expected. view less | |
| Tackmelt A 44 | Ichemco | Tackmelt A 44 is a hot melt pressure sensitive adhesive based on SIS synthetic rubber and synthetic resins. It contains special antioxidants to guarantee a good ageing resistance. Tackmelt A 44 is most commonly used in label and double-sided adhesive tape...view more Tackmelt A 44 is a hot melt pressure sensitive adhesive based on SIS synthetic rubber and synthetic resins. It contains special antioxidants to guarantee a good ageing resistance. Tackmelt A 44 is most commonly used in label and double-sided adhesive tape applications. view less | |
| Tackmelt A 44 UV | Ichemco | Tackmelt A 44 UV is a hot-melt adhesive, based on SIS synthetic rubber and synthetic resins. It contains special antioxidants and UV stabilizer to guarantee a good ageing and light resistance. This product has a viscosity at 150°C of 7000-13,000 mPa.s and...view more Tackmelt A 44 UV is a hot-melt adhesive, based on SIS synthetic rubber and synthetic resins. It contains special antioxidants and UV stabilizer to guarantee a good ageing and light resistance. This product has a viscosity at 150°C of 7000-13,000 mPa.s and a viscosity at 185°C of 2000-5000 mPa.s. Tackmelt A 44 UV is most commonly used in label and double-sided adhesive tape applications. view less | |
| Tackmelt A40 | Ichemco | Tackmelt A40 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 12,000-20,000 mPa.s and a viscosity at 185°C of 4000-8000 mPa.s. Tackmelt A40 is most commonly used in permanent label production applications. | |
| Tackmelt A43 A | Ichemco | Tackmelt A43 A is an amber-colored hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 17,000-27,000 mPa.s and a viscosity at 185°C of 4000-6000 mPa.s. Tackmelt A43 A is most commonly used in label and double-sided tape produc...view more Tackmelt A43 A is an amber-colored hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 17,000-27,000 mPa.s and a viscosity at 185°C of 4000-6000 mPa.s. Tackmelt A43 A is most commonly used in label and double-sided tape production applications. view less | |
| Tackmelt A45 | Ichemco | Tackmelt A45 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 18,000-30,000 mPa.s and a viscosity at 180°C of 6000-9000 mPa.s. Tackmelt A45 is most commonly used in label and double-sided tape production applications. | |
| Tackmelt A46 M | Ichemco | Tackmelt A46 M is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 12,000-16,000 mPa.s and a viscosity at 185°C of 3000-7000 mPa.s. Tackmelt A46 M is most commonly used in label and double-sided tape production applications...view more Tackmelt A46 M is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 12,000-16,000 mPa.s and a viscosity at 185°C of 3000-7000 mPa.s. Tackmelt A46 M is most commonly used in label and double-sided tape production applications. view less | |
| Tackmelt A48 M2 | Ichemco | Tackmelt A48 M2 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 60,000-90,000 mPa.s and a viscosity at 180°C of 16,000-25,000 mPa.s. Tackmelt A48 M2 is most commonly used in adhesive applications where high tack, cohesi...view more Tackmelt A48 M2 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 60,000-90,000 mPa.s and a viscosity at 180°C of 16,000-25,000 mPa.s. Tackmelt A48 M2 is most commonly used in adhesive applications where high tack, cohesion, and thermal resistance are required. view less | |
| Tackmelt A49 | Ichemco | Tackmelt A49 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 20,000-40,000 mPa.s and a viscosity at 185°C of 4000-8000 mPa.s. Tackmelt A49 is most commonly used in label and double-sided tape production applications. | |
| Tackmelt A8 | Ichemco | Tackmelt A8 is a hot melt pressure sensitive adhesive based on thermoplastic elastomers (SIS) and synthetic resins. Special synergic antioxidants are added to guarantee the best ageing resistance. This product has a viscosity at 150°C of 9600-12500 mPa.s...view more Tackmelt A8 is a hot melt pressure sensitive adhesive based on thermoplastic elastomers (SIS) and synthetic resins. Special synergic antioxidants are added to guarantee the best ageing resistance. This product has a viscosity at 150°C of 9600-12500 mPa.s and a viscosity at 180°C of 2500-4500 mPa.s. Tackmelt A8 is most commonly used at medium-low temperatures to laminate different products such as synthetic leathers, foams, non-wovens, and fabrics. view less | |
| Tackmelt A9 | Ichemco | Tackmelt A9 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 20,000-40,000 mPa.s and a viscosity at 180°C of 7000-11,000 mPa.s. Tackmelt A9 is most commonly used in medium-low temperature lamination applications. | |
| Tackmelt HM 10 A | Ichemco | Tackmelt HM 10 A is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 25,000-35,000 mPa.s and a viscosity at 185°C of 5000-10,000 mPa.s. Tackmelt HM 10 A is most commonly used in dielectric tape production applications. | |
| Tackmelt HM 15 A | Ichemco | Tackmelt HM 15 A is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 50,000-80,000 mPa.s and a viscosity at 180°C of 20,000-25,000 mPa.s. Tackmelt HM 15 A is most commonly used in double-sided adhesive tape, as well as insu...view more Tackmelt HM 15 A is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 50,000-80,000 mPa.s and a viscosity at 180°C of 20,000-25,000 mPa.s. Tackmelt HM 15 A is most commonly used in double-sided adhesive tape, as well as insulating foam and panel production applications. view less | |
| Tackmelt HM 15 B | Ichemco | Tackmelt HM 15 B is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 60,000-90,000 mPa.s and a viscosity at 180°C of 15,000-20,000 mPa.s. Tackmelt HM 15 B is most commonly used in double-sided adhesive tape, as well as insu...view more Tackmelt HM 15 B is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 60,000-90,000 mPa.s and a viscosity at 180°C of 15,000-20,000 mPa.s. Tackmelt HM 15 B is most commonly used in double-sided adhesive tape, as well as insulating foam and panel production applications. view less | |
| Tackmelt R 002 | Ichemco | Tackmelt R 002 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 90,000-160,000 mPa.s and a viscosity at 180°C of 20,000-40,000 mPa.s. Tackmelt R 002 is most commonly used in opaque removable film and paper label producti...view more Tackmelt R 002 is a hot melt pressure sensitive adhesive. This product has a viscosity at 150°C of 90,000-160,000 mPa.s and a viscosity at 180°C of 20,000-40,000 mPa.s. Tackmelt R 002 is most commonly used in opaque removable film and paper label production applications. view less |
