| Airase® 4500 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Airase® 4500 Defoamer is a proprietary organic oil defoamer designed to control and typically eliminate foam, pinholes and entrapped air in waterbased inks, adhesives and coatings without generating surface defects. It does not contain added mineral oils,...view more Airase® 4500 Defoamer is a proprietary organic oil defoamer designed to control and typically eliminate foam, pinholes and entrapped air in waterbased inks, adhesives and coatings without generating surface defects. It does not contain added mineral oils, hazardous air pollutants (HAPs), or alkyl phenol ethoxylates (APEs). view less | |
| Airase® 5700 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Airase® 5700 Defoamer is a structured siloxane defoamer line (SSDL) defoamer - a member of aline of products that spans the application space from strong defoaming to high compatibility. Airase® 5700 Defoamer is a formulated product that contains no adde...view more Airase® 5700 Defoamer is a structured siloxane defoamer line (SSDL) defoamer - a member of aline of products that spans the application space from strong defoaming to high compatibility. Airase® 5700 Defoamer is a formulated product that contains no added solvent, HAPs, or alkylphenol ethoxylates. This siloxane-based defoamer was developed for use in a wide range of water-based applications. Airase® 5700 Defoamer is formulated for incorporation in the let-down of a coating or ink. Airase® 5700 Defoamer can provide an excellent balance of effective defoaming and film compatibility. view less | |
| Carbowet® 138 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Carbowet® 138 Surfactant is a multifunctional additive for pigment and substrate wetting. This nonionic surfactant is typically used alone or in combination with an anionic surfactant. This cost-effective surfactant can provide rapid substrate and pigment...view more Carbowet® 138 Surfactant is a multifunctional additive for pigment and substrate wetting. This nonionic surfactant is typically used alone or in combination with an anionic surfactant. This cost-effective surfactant can provide rapid substrate and pigment wetting and perform in a wide range of applications. view less | |
| Carbowet® GA-211 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Carbowet® GA-211 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-211 surfactant can provide exceptional dry pigment w...view more Carbowet® GA-211 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-211 surfactant can provide exceptional dry pigment wetting and deaeration and optimal milling efficiency, allowing for faster and stronger color development. The combination of properties provided by Carbowet® GA-211 surfactant can be used in a variety of applications for dynamic wetting, compatibilization, emulsification, and stabilization where an easy-to-incorporate liquid additive is desired. Carbowet® GA-211 surfactant offers low foam and strong dynamic wetting properties. view less | |
| Carbowet® GA-221 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Carbowet® GA-221 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-221 surfactant can provide exceptional dry pigment w...view more Carbowet® GA-221 Surfactant is an optimized combination of nonionic additives designed to provide multifunctional wetting and stabilization benefits in a wide range of aqueous formulations. Carbowet® GA-221 surfactant can provide exceptional dry pigment wetting and deaeration and optimizes milling efficiency, allowing for faster and stronger color development. The combination of properties provided by Carbowet® GA-221 surfactant can be used in a variety of applications for dynamic wetting, compatibilization, emulsification, and stabilization where an easy-to-incorporate liquid additive is desired. Compared to related products, Carbowet® GA-221 surfactant offers the most stabilization benefits and is a first choice for organic and carbon black pigment dispersions. view less | |
| DYNOL™ 604 Surfactant | Evonik Operations GmbH, BL Interface & Performance | DYNOL™ 604 Surfactant is a low-VOC, low foam, nonionic wetting agent ideal for high-performance waterborne applications. This wetting agent has the ability to reduce both equilibrium and dynamic surface tension to a degree not found with other surfactants...view more DYNOL™ 604 Surfactant is a low-VOC, low foam, nonionic wetting agent ideal for high-performance waterborne applications. This wetting agent has the ability to reduce both equilibrium and dynamic surface tension to a degree not found with other surfactants. view less | |
| Dynol™ 607 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Dynol™ 607 surfactant has been developed to meet the growing need for high performance and cost effective surfactants. It provides a unique balance of properties for a wide range of waterbased industrial applications compared with traditional surfactants ...view more Dynol™ 607 surfactant has been developed to meet the growing need for high performance and cost effective surfactants. It provides a unique balance of properties for a wide range of waterbased industrial applications compared with traditional surfactants such as fluorosurfactants and silicones. Dynol™ 607 applications may include, coatings, graphic arts, adhesives, latex dipping, dye and pigment synthesis, pigment grinding, metalworking fluids, waste water treatment and more. view less | |
| Dynol™ 980 Surfactant | Evonik Operations GmbH, BL Interface & Performance | Dynol™ 980 superwetting surfactant is an optimized siloxane-based surfactant providing good equilibrium and dynamic surface tension reduction in a wide range of aqueous formulations. Designed to provide superwetting on difficult-to-wet substrates, it offe...view more Dynol™ 980 superwetting surfactant is an optimized siloxane-based surfactant providing good equilibrium and dynamic surface tension reduction in a wide range of aqueous formulations. Designed to provide superwetting on difficult-to-wet substrates, it offers superior substrate wetting with low foam and excellent compatibility. The characteristics of Dynol™ 980 surfactant enable exceptional performance in waterborne wood coatings and overprint varnishes. This product can also provide good flow and leveling under diverse application conditions. view less | |
| Flytac 102-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...view more Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR. This product has a colour gardener (in 50% Toluene) of 4 max., an acid value of 20mg KOH/g max., and a softening point (R&B) of 97-100℃. view less | |
| FLYTAC 103-85 | Guangzhou Flying Dragon Chemical Ltd. | A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS,...view more A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. view less | |
| Flytac 103-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for thi...view more Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for this product include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It an also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. Flytac 103-E has a softening point (R&B) of 82-90°C min., an acid value of 3-8mg KOH/g max., and a colour gardener (in 50% Toluene) of 8 max. view less | |
| Flytac 104 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used...view more Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used as raw material for the manufacture of a number of products including bookbinding, caulking, paint and coatings, personal care and cosmetics, pressure sensitive adhesives, rubber and plastic modification, solvent-borne adhesives, tapes and labels, waterborne adhesives, and wax modification. This product has an abietic acid of 2.0% max., a softening point (R&B) of 76°C min., and a dehydroabietic acid of 8.0% max. view less | |
| Flytac 105-L | Guangzhou Flying Dragon Chemical Ltd. | Flytac105-L is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, waterborne adhesives, non-wovens, packaging, tapes and labels, as well as in wax depilatories. In...view more Flytac105-L is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, waterborne adhesives, non-wovens, packaging, tapes and labels, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-oxidizing, color-stable, highly tacky liquid resin. Flytac105-L has a softening point (R&B) of 85°C, an acid value of 9mg KOH/g max., and an ash content of 0.2% max. view less | |
| Flytac 106-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 106-100 is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesiv...view more Flytac 106-100 is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesive formulations, it contributes improved resistance to oxidation, greater heat stability, better retention of color, and greater retention of tack-imparting properties than ordinary rosin ester resins. Flytac 106-100 has a color gardener of 8~10, a specific gravity (25°C/25°C) of 1.060~1.090, and a softening point (R&B) of 95-102°C min. view less | |
| Flytac 106-100L | Guangzhou Flying Dragon Chemical Ltd. | Flytac 106-100L is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesi...view more Flytac 106-100L is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesive formulations, it contributes improved resistance to oxidation, greater heat stability, better retention of color, and greater retention of tack-imparting properties than ordinary rosin ester resins. This product has a color gardener of 4~6, a softening point (R&B) of 95-102°C, and a specific gravity (25°C/25°C) of 1.060~1.090. view less | |
| Flytac 107 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 107 is made of derivatives of gum rosin obtained by chemical treatment to reduce the Abietic Acid content. It is used as a tackifier for pressure sensitive adhesive, in the manufacture of SBR and other synthetic rubbers, as well as in important com...view more Flytac 107 is made of derivatives of gum rosin obtained by chemical treatment to reduce the Abietic Acid content. It is used as a tackifier for pressure sensitive adhesive, in the manufacture of SBR and other synthetic rubbers, as well as in important component for making potassium soaps. This product has a dehydrated acid content of 52.0% min., an unsaponifiable material of 10.0% max., and an abietic acid of 1% max. view less | |
| Flytac 111-101 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 111-101 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly st...view more Flytac 111-101 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly stabilized rosins commercially available, and is especially indicated as the tackifier in solvent adhesives and hot-melt applied coatings and adhesives that must excel in these properties. Flytac 111-101 has a tetrahydro resin acid of 10.0% min., an abietic acid of 2.0% max., and a dehydroabietic acid of 10.0% max. view less | |
| Flytac 111-301 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 111-301 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly st...view more Flytac 111-301 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly stabilized rosins commercially available, and is especially indicated as the tackifier in solvent adhesives and hot-melt applied coatings and adhesives that must excel in these properties. Flytac 111-301 has an abietic acid of 0-0.1% max., a softening point (R&B) of 78°C, and a tetrahydro resin acid level of 30.0-40.0%. view less | |
| Flytac 114-125 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-125 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...view more Flytac 114-125 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. This product offers color stability, is resistant to yellowing, and has good heat resistance and adhesion. Flytac 114-125 has a color (Gardner Grade) of 5 max., an acid value of 30mg KOH/g max., and a softening point (R&B) of 125 ± 2°C min. view less | |
| Flytac 114-130 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-130 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...view more Flytac 114-130 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. It offers color stability, resistant to yellowing, good heat resistance and adhesion. Flytac 114-130 has a softening point (R&B) of 130 ± 2°C min., an acid value of 30mg KOH/g max., and a color (Gardener Grade) of 5 max. view less | |
| Flytac 114-135 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-135 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...view more Flytac 114-135 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. It offers color stability, resistant to yellowing, good heat resistance and adhesion. Flytac 114-135 has an acid value of 30mg KOH/g max., a color (Gardner Grade) of 5 max., and a softening point (R&B) of 135 ± 2°C min. view less | |
| Flytac 115 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 115 is a specially designed highly stable 50% water-borne polymeric type tackifier dispersion with 23 degree (rolling & ball) softening point. It is a highly stabilized rosin ester dispersion designed to provide superior performance in adhesives pr...view more Flytac 115 is a specially designed highly stable 50% water-borne polymeric type tackifier dispersion with 23 degree (rolling & ball) softening point. It is a highly stabilized rosin ester dispersion designed to provide superior performance in adhesives properties, and is compatible with anionic & nonionic types of latexes. It adheres to a wide range of substrates. This product has a viscosity ((Brookifield 2#, 60rpm, 25°C,cps) PH(25°C)) of 150 max, a particle size (AVG) of 0.25μm, and a density (25°C) of 1.02g/ml. view less | |
| Flytac 116-110 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-110 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is deal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 190 ± 10mg K...view more Flytac 116-110 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is deal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 190 ± 10mg KOH/g, a softening point (R&B) of 110± 5°C, and a color gardner (50% Benzene solution) of 5 max. view less | |
| Flytac 116-130 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-130 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideally used for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 180...view more Flytac 116-130 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideally used for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 180 ± 10mg KOH/g, a softening point (R&B) of 130 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. view less | |
| Flytac 116-150 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-150 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 170 ± 10mg ...view more Flytac 116-150 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 170 ± 10mg KOH/g, a softening point (R&B) of 150 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. view less | |
| Flytac 116-160 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-160 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 200 ± 10mg ...view more Flytac 116-160 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 200 ± 10mg KOH/g, a softening point (R&B) of 160 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. view less | |
| Flytac 117-115 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-115 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-form...view more Flytac 117-115 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-115 has a softening point (R&B) of 110-120°C min., a dissoluble matter in hot water amount of 0.20, and an acid number of 145mg KOH/g min. view less | |
| Flytac 117-140 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-140 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-form...view more Flytac 117-140 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-140 has a softening point (R&B) of 135-145°C min., an acid number of 145mg KOH/g min., and a dissoluble matter in alcohol of 0.03% max. view less | |
| Flytac 117-95 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-95 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-formi...view more Flytac 117-95 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-95 has an acid number of 150mg KOH/g, a dissoluble matter in alcohol of 0.03% max., and a softening point (R&B) of 90-100°C min. view less | |
| FLYTAC 120-100W | Guangzhou Flying Dragon Chemical Ltd. | A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granu...view more A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granules, SBS and SIS base hot melt and pressure sensitive adhesives, EVA based hot melt adhesives for quality of packing, booking and cigarettes adhesives, hot melt paints and sealants and water or solvent bases adhesives. view less | |
| FLYTAC 120-90W | Guangzhou Flying Dragon Chemical Ltd. | A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granu...view more A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granules, SBS and SIS base hot melt and pressure sensitive adhesives, EVA based hot melt adhesives for quality of packing, booking and cigarettes adhesives, hot melt paints and sealants and water or solvent bases adhesives. view less | |
| Flytac 188-C5 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C5 is a kind of thermal plasticizing resin produced by C5, by-products of petroleum cracking, through pretreatment, polymerization and distillation. The major usages are tackifier for pressure sensitive adhesive, because of its well balance PSA...view more Flytac 188-C5 is a kind of thermal plasticizing resin produced by C5, by-products of petroleum cracking, through pretreatment, polymerization and distillation. The major usages are tackifier for pressure sensitive adhesive, because of its well balance PSA properties such as trackness, adhesive strength and cohesive strength. It can also be used in the production of paints, adhesives and in rubber industries. Flytac 188-C5 has an average molecular weight of 1000-2600, a melt viscosity (CPS at 200°C) of 300 max., and a softening point (R&B) of 95-105°C. view less | |
| Flytac 188-C5/C9 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C5/C9 is a copolymerization hydrocarbon petroleum resin, whose materials are C5 fraction and C9 fraction. It is a new product for the market, and has the good characters of C5 hydrocarbon resin and C9 hydrocarbon resin. It is an important raw m...view more Flytac 188-C5/C9 is a copolymerization hydrocarbon petroleum resin, whose materials are C5 fraction and C9 fraction. It is a new product for the market, and has the good characters of C5 hydrocarbon resin and C9 hydrocarbon resin. It is an important raw material for the product of paints, adhesives, and in rubber industries. Flytac 188-C5/C9 has an ash content of 0.1% max., an acid value of 0.3mg KOH/g max., and a softening point (B&R) of 90~120°C max. view less | |
| Flytac 188-C9 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C9 hydrocarbon petroleum resin is a kind of resin produced by C9 fraction, by products of petroleum cracking, through pretreatment,polymerization and distillation. It isn‘t a high polymer but a low polymer, with the molecular weight between 300...view more Flytac 188-C9 hydrocarbon petroleum resin is a kind of resin produced by C9 fraction, by products of petroleum cracking, through pretreatment,polymerization and distillation. It isn‘t a high polymer but a low polymer, with the molecular weight between 300-3000. It is an important raw material for the production of paints, adhesives and rubber industries. Flytac 188-C9 has a softening point (B&R) of 90-140°C, an acid value of 0.5mg KOH/g max., and an ash amount of 0.1% max. view less | |
| Flytac 188-HC5 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-HC5 hydrocarbon resin is a low molecular weight fully hydrogenated, water-white, inert, thermoplastic resin derived from petrochemical feedstocks. This resin is especially designed as tackifier in hot-melt adhesives requiring excellent color re...view more Flytac 188-HC5 hydrocarbon resin is a low molecular weight fully hydrogenated, water-white, inert, thermoplastic resin derived from petrochemical feedstocks. This resin is especially designed as tackifier in hot-melt adhesives requiring excellent color retention upon aging. It is an important raw material for the production of paints, adhesives and rubber industries. Flytac 188-HC5 has a softening point (B&R) of 95-105°Cg, an acid value of 0.5mg KOH/g max., and an ash amount of 0.02% max. view less | |
| Flytac102-100F | Guangzhou Flying Dragon Chemical Ltd. | Flytac102-100F is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...view more Flytac102-100F is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, Pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR.This product has a melt viscosity (CPS at 150°C) of 850-1300, a softening point (R&B) of 97-103°C, and a specific gravity (25°C/25°C) of 1.060~1.090. view less | |
| Flytac103-90 | Guangzhou Flying Dragon Chemical Ltd. | Flytac103-90 is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses...view more Flytac103-90 is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. This product has a colour gardener (in 50% Toleune) of 3 max., an acid value of 10mg KOH/g max., and a softening point (R&B) of 87-92°C min. view less | |
| Flytac105-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac105-E is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-ox...view more Flytac105-E is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-oxidizing, color-stable, highly tacky liquid resin. This product is ideally used for wax modification, waterborne adhesives, tapes and labels, solventborne adhesives, rubber and plastic modification, and paint and coatings. Flytac105-E has a softening point (R&B) of 78-88°C min., a specific gravity (25°C/25°C) of 1.060~1.090, and an ash content of 0.1% max. view less | |
| Polymer ST 48 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 48 offers a good handling viscosity and is therefore easy to apply manually. Formulation surfaces are quickly tack-free after application, which ensures rapid processing and avoids long waiting times. It is especially recommended for the applic...view more Polymer ST 48 offers a good handling viscosity and is therefore easy to apply manually. Formulation surfaces are quickly tack-free after application, which ensures rapid processing and avoids long waiting times. It is especially recommended for the application as sealant for interior or exterior joints, e.g. expansion or connection joints, interior joints for dry walling, joints at staircases. view less | |
| Polymer ST 61 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 61 is a high quality polymer which is used for wood floor adhesive formulations. Polymer ST 61 allows a high degree of flexibility for the formulations: adhesives with high strength and hardness are possible as well as soft adhesives with high ...view more Polymer ST 61 is a high quality polymer which is used for wood floor adhesive formulations. Polymer ST 61 allows a high degree of flexibility for the formulations: adhesives with high strength and hardness are possible as well as soft adhesives with high elasticity. view less | |
| Polymer ST 61 LV | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 61 LV is a plasticizer-free product which addresses the same formulation properties as Polymer ST 61. Its viscosity is approx. 70 % less, thus it allows quicker dosing, lower formulation viscosities and higher possible filler loading levels. | |
| Polymer ST 77 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 77 is free of phthalates and is highly recommended for demanding applications where a balanced stress-strain behavior is required as in transport and assembly applications. Examples for the use of Polymer ST 77-based formulations are the assemb...view more Polymer ST 77 is free of phthalates and is highly recommended for demanding applications where a balanced stress-strain behavior is required as in transport and assembly applications. Examples for the use of Polymer ST 77-based formulations are the assembly of superstructural parts, bumpers, etc. Mechanical fastening is often avoided as it could cause damage to the materials used. In addition, it could negatively affect the design. view less | |
| Polymer ST 80 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 80 is a high quality binder for adhesive formulations where high bonding strength and high surface hardness after curing are required. | |
| Polymer ST 81 | Evonik Operations GmbH, BL Interface & Performance | Polymer ST 81 does not contain plasticizers, it offers a large variability in formulation design. It allows the formulation of both tin- and phthalate-free products. It allows formulators to enter markets such as wood construction, transport and automotiv...view more Polymer ST 81 does not contain plasticizers, it offers a large variability in formulation design. It allows the formulation of both tin- and phthalate-free products. It allows formulators to enter markets such as wood construction, transport and automotive, assembly as well as light-weight construction. view less | |
| SURFYNOL® 104 | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® 104 surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104 surfactant is a nonionic molecule containing ...view more SURFYNOL® 104 surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104 surfactant is a nonionic molecule containing a hydrophilic portion in the middle of two symmetrical hydrophobic groups. Its unique chemical structure allows this product to provide multifunctional properties such as surface tension reduction, foam control and viscosity stabilization. view less | |
| SURFYNOL® 104A | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® 104A surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104A surfactant is a nonionic molecule containing...view more SURFYNOL® 104A surfactant is one in a series of Air Products’ surfactants that provide a unique combination of performance benefits including wetting, defoaming and improving pigment dispersions. SURFYNOL® 104A surfactant is a nonionic molecule containing a hydrophilic portion in the middle of two symmetrical hydrophobic groups. Its unique chemical structure allows this product to provide multifunctional properties such as surface tension reduction, foam control and viscosity stabilization. view less | |
| SURFYNOL® 104BC | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in 2-Butoxyethanol. | |
| SURFYNOL® 104DPM | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Dipropylene Glycol Monomethyl Ether. | |
| SURFYNOL® 104E | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Ethylene Glycol. | |
| SURFYNOL® 104H SURFACTANT | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 75% active liquid in Ethylene Glycol. | |
| SURFYNOL® 104PA | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Isopropyl Alcohol. | |
| SURFYNOL® 104PG-50 | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 50% active liquid in Propylene Glycol. | |
| SURFYNOL® 104S | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that has multifunctional benefits, including wetting and foam control, in aqueous systems. 46% active powder on Amorphous Silica. | |
| Surfynol® 107 L | Evonik Operations GmbH, BL Interface & Performance | Surfynol® 107 L is a low-viscosity surfactant that provides substratre wetting and defoaming properties. It also acts as coalescing aid. | |
| SURFYNOL® 2502 | Evonik Operations GmbH, BL Interface & Performance | An ethoxylated/propoxylated acetylenic-based surfactant that provides specific performance benefits in a broad range of water-based systems. 100% active liquid. | |
| SURFYNOL® 420 | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that functions both as a wetting agent and foam control agent. 100% active liquid with an HLB of 4. | |
| SURFYNOL® 440 | Evonik Operations GmbH, BL Interface & Performance | A nonfoaming, nonionic surfactant that is employed for substrate wetting. 100% active liquid with an HLB of 8. | |
| SURFYNOL® 465 | Evonik Operations GmbH, BL Interface & Performance | A nonionic, low-foaming surfactant that is utilized for its wetting and slight emulsification properties. It has a high cloud point for utilization in high-temperature systems. 100% active liquid with an HLB of 13. | |
| SURFYNOL® 485W | Evonik Operations GmbH, BL Interface & Performance | A nonionic surfactant that functions as a wetting agent and has slight emulsification properties. 75% active liquid with an HLB of 17. | |
| SURFYNOL® 82 | Evonik Operations GmbH, BL Interface & Performance | This is a 95% Dimethyl Octynediol surfactant. | |
| SURFYNOL® CT-131 | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® CT-131 is a solvent-free, low-foaming pigment grind aid designed for use in aqueous systems. | |
| SURFYNOL® CT-171 | Evonik Operations GmbH, BL Interface & Performance | SURFYNOL® CT-171 is a solvent-free anionic/nonionic grind aid designed to provide both effective pigment wetting and dispersing characteristics for many types of organic pigments. | |
| Surfynol® DF-110 D | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF 110 D is a very compatible molecular defoamer basedon Gemini surfactant technology. Free of silicone and silica. Offers additional dynamic wetting properties. | |
| Surfynol® DF-110BC Defoamer | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF-110BC defoamer is a highly effective, nonionic, molecular defoamer and deaerator. This defoaming/deairentraining agent can be used for a wide variety of applications where foam prevention or foam elimination is necessary without causing surfa...view more Surfynol® DF-110BC defoamer is a highly effective, nonionic, molecular defoamer and deaerator. This defoaming/deairentraining agent can be used for a wide variety of applications where foam prevention or foam elimination is necessary without causing surface defects. view less | |
| SURFYNOL® DF-110L | Evonik Operations GmbH, BL Interface & Performance | Surfynol DF-110C, Surfynol DF-110D, and Surfynol DF-110L molecular defoamers are highly effective, non-ionic organic products. They do not contain silicone, silica or fluoro products. These three defoaming/de-air entraining agents are useful for a wide ...view more Surfynol DF-110C, Surfynol DF-110D, and Surfynol DF-110L molecular defoamers are highly effective, non-ionic organic products. They do not contain silicone, silica or fluoro products. These three defoaming/de-air entraining agents are useful for a wide variety of applications where foam prevention or foam elimination is nescessary without causing surface defects. view less | |
| Surfynol® DF-178 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF-178 Defoamer is a formulated defoamer and de-aerator that provides strong defoaming and microfoam control and is particularly effective in spray applications. It is a liquid, 100% active, silicone-based product developed specifically for appl...view more Surfynol® DF-178 Defoamer is a formulated defoamer and de-aerator that provides strong defoaming and microfoam control and is particularly effective in spray applications. It is a liquid, 100% active, silicone-based product developed specifically for applications in water-borne coatings and graphic arts that demand both powerful defoaming and defect-free surfaces. view less | |
| Surfynol® DF-220 Defoamer | Evonik Operations GmbH, BL Interface & Performance | Surfynol® DF-220 Defoamer is a 100% active, silicone-free, silica-free, and alkylphenol ethoxylate (APE)-free organic defoamer that can provide not only high initial efficacy, but also long term sustained defoaming. It is a clear, low viscosity liquid tha...view more Surfynol® DF-220 Defoamer is a 100% active, silicone-free, silica-free, and alkylphenol ethoxylate (APE)-free organic defoamer that can provide not only high initial efficacy, but also long term sustained defoaming. It is a clear, low viscosity liquid that has been specifically designed to be used in a variety of water-based formulations, including printing inks, coatings and adhesives. view less | |
| SURFYNOL® DF-37 | Evonik Operations GmbH, BL Interface & Performance | A nonionic, acetylenic-based defoamer which promotes foam control as well as surface wetting. 100% active liquid. | |
| SURFYNOL® DF-37 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A nonionic, acetylenic-based defoamer which promotes foam control as well as surface wetting. A unique additive designed to minimize web formation during latex glove and waterborne coating dipping processes. | |
| SURFYNOL® DF-58 | Evonik Operations GmbH, BL Interface & Performance | A silicone-based foam control agent useful in aqueous systems. The product has strong foam control and deairation performance. 100% active liquid. | |
| SURFYNOL® DF-58 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A silicone-based foam control agent useful in aqueous systems. It has strong foam control and deairation performance. Developed for use in water-based coating and ink formulations where strong, rapid defoaming is required. 100% active liquid. | |
| SURFYNOL® DF-62 | Evonik Operations GmbH, BL Interface & Performance | An ether-modified polysiloxane-based defoamer designed to provide excellent knockdown defoaming and sustained antifoaming over time. 100% active liquid. | |
| SURFYNOL® DF-62 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | Ether-modified, silicone defoamer designed to provide excellent knockdown defoaming and sustained antifoaming over time in a variety of waterborne formulations. Useful when long-term defoamer efficacy is needed. 100% active liquid. | |
| SURFYNOL® DF-66 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A liquid, acetylenic-modified polysiloxane-based emulsion defoamer which provides excellent balance of initial knockdown and sustained defoaming with no detrimental effects. Designed for use in aqueous ink and coating systems. 46% active liquid. | |
| SURFYNOL® DF-695 | Evonik Operations GmbH, BL Interface & Performance | A silicone emulsion defoamer, which provides initial and sustained defoaming performance in water-based formulations. 100% active liquid. | |
| SURFYNOL® DF-695 DEFOAMER | Evonik Operations GmbH, BL Interface & Performance | A silicone-based emulsion defoamer designed for use in aqueous ink systems. It is recommended for use in grinding and dispersion as well as letdown applications. 100% active liquid. | |
| SURFYNOL® MD-600S | Evonik Operations GmbH, BL Interface & Performance | This is a highly effective powder product designed to eliminate air entrapment in cementitious-based products for the construction industry. It allows for fast-acting defoaming with long-lasting deaeration, at a molecular level. It also ensures the fast...view more This is a highly effective powder product designed to eliminate air entrapment in cementitious-based products for the construction industry. It allows for fast-acting defoaming with long-lasting deaeration, at a molecular level. It also ensures the fast escape of air entrapped while incorporating water and during mixing. view less | |
| Surfynol® MD20 | Evonik Operations GmbH, BL Interface & Performance | Surfynol® MD20 is a 100% active, nonsilicone, liquid product based on Gemini Surfactant Technology. This multifunctional defoamer provides a combination of foam control and dynamic wetting, with the potential to reduce overall additive levels, while minim...view more Surfynol® MD20 is a 100% active, nonsilicone, liquid product based on Gemini Surfactant Technology. This multifunctional defoamer provides a combination of foam control and dynamic wetting, with the potential to reduce overall additive levels, while minimizing surface defects. Additional advantages of Surfynol® MD20 include, long-lasting defoamer efficacy, ease of incorporation and good compatibility without separation, synergestic with typical wetting agents, eliminates microfoam, wide compounding latitude, solvent-free and temperature and pH stable (pH 1-13). view less | |
| SURFYNOL® PSA-336 | Evonik Operations GmbH, BL Interface & Performance | A powerful solvent-free wetting agent with moderate foaming tendencies. | |
| SURFYNOL® SE | Evonik Operations GmbH, BL Interface & Performance | A nonionic defoaming surfactant which can act as a highly effective wetting agent, defoamer and viscosity stabilizer and often performs more than one of these functions in combination. 80% active liquid with an HLB of 4-5. | |
| SURFYNOL® SE-F | Evonik Operations GmbH, BL Interface & Performance | A nonionic self-emulsifiable surfactant that will reduce surface tension and control foam. 80% active liquid with an HLB of 4-5. | |
| TEGOPAC® Bond 150 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 150 is recommended for usage as a binder in assembly adhesives and sealant formulations. The combination of outstanding through-cure and excellent elastic recovery properties allows formulations with TEGOPAC® Bond 150 to be used in a number ...view more TEGOPAC® Bond 150 is recommended for usage as a binder in assembly adhesives and sealant formulations. The combination of outstanding through-cure and excellent elastic recovery properties allows formulations with TEGOPAC® Bond 150 to be used in a number of demanding applications, e.g. in construction of sandwich elements, for flexible bonding in transport applications or for high quality expansion joints. view less | |
| TEGOPAC® Bond 160 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 160 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 160 shows excellent through cure properties,...view more TEGOPAC® Bond 160 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 160 shows excellent through cure properties, improved water & thermal resistance and excellent elastic recovery properties. The low polymer viscosity allows quick & easy handling. view less | |
| TEGOPAC® Bond 170 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 170 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 170 shows excellent through cure properties,...view more TEGOPAC® Bond 170 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 170 shows excellent through cure properties, improved water & thermal resistance and excellent elastic recovery properties. The low polymer viscosity allows quick & easy handling. view less | |
| TEGOPAC® Bond 251 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Bond 251 is a hybrid polymer with a modified backbone that contains hydrophilic segments. Formulations with TEGOPAC® Bond 251 are suitable to replace flexible PUR adhesives and sealants. | |
| TEGOPAC® RD 1 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® RD 1 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers,...view more TEGOPAC® RD 1 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers, and other additives is possible to address applications like parquet adhesives, roof sealing applications or pressure sensitive adhesives. view less | |
| TEGOPAC® RD 2 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® RD 2 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers,...view more TEGOPAC® RD 2 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers, and other additives is possible to address applications like parquet adhesives, roof sealing applications or pressure sensitive adhesives. view less | |
| TEGOPAC® Seal 100 | Evonik Operations GmbH, BL Interface & Performance | TEGOPAC® Seal 100 is a moisture curing silane-modified polymer recommended for low modulus sealant formulations which are used in construction applications (e.g. for façades, expansion joints, etc. ) or for indoor applications. TEGOPAC® Seal 100 is also ...view more TEGOPAC® Seal 100 is a moisture curing silane-modified polymer recommended for low modulus sealant formulations which are used in construction applications (e.g. for façades, expansion joints, etc. ) or for indoor applications. TEGOPAC® Seal 100 is also recommended for use in sealant and adhesive formulations where vibration and sound dampening is an issue. view less | |
| ZetaSperse® 170 Dispersant | Evonik Operations GmbH, BL Interface & Performance | ZetaSperse® 170 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles with acidic surface groups. A nonionic stabilizing surfactant, ZetaSperse® 170 dispersant utilizes a tertiary amine anchoring grou...view more ZetaSperse® 170 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles with acidic surface groups. A nonionic stabilizing surfactant, ZetaSperse® 170 dispersant utilizes a tertiary amine anchoring group that has been found to have particularly strong affinity for carbon black pigments, titanium dioxide pigments, and other pigments and particles with acidic surface groups. ZetaSperse® 170 dispersant is most effective when used as a secondary dispersant in conjunction with anionic polymeric dispersants and grind resins where it can provide significant wetting, milling, and steric stabilization benefits, often improving milling efficiency, color development, and dispersion stability, allowing formulators to achieve higher performance. view less | |
| ZetaSperse® 179 Dispersant | Evonik Operations GmbH, BL Interface & Performance | ZetaSperse® 179 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles. A nonionic, high-HLB surfactant, ZetaSperse® 179 Dispersant provides performance benefits in the aqueous dispersion of organic, c...view more ZetaSperse® 179 Dispersant was designed to provide steric stabilization for the aqueous dispersion of pigments and particles. A nonionic, high-HLB surfactant, ZetaSperse® 179 Dispersant provides performance benefits in the aqueous dispersion of organic, carbon black, and inorganic pigments as well as fillers and functional solid chemicals. Ideal applications include resinated dispersions, colorants and pigment dispersions, inks and graphic arts, architectural and industrial coatings, and industrial processes. view less |
