| Acclaim® 8200 | Covestro | Acclaim® 8200 polyol is a 8,000-molecular-weight diol based on propylene oxide. This high-performance, low- monol polyether is prepared with Bayer’s proprietary IMPACT® technology, using a patented organo-metallic propoxylation catalyst. It may be use...voir plus Acclaim® 8200 polyol is a 8,000-molecular-weight diol based on propylene oxide. This high-performance, low- monol polyether is prepared with Bayer’s proprietary IMPACT® technology, using a patented organo-metallic propoxylation catalyst. It may be used in polyurethane and other applications, including cast elastomers, sealants, epoxy flexibilizers, defoamers, lubricants, crude oil de-emulsifiers, and plasticizers. As with any product, the use of Acclaim 8200 polyol in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Acclaim® Polyol 4200 | Covestro | Acclaim® Polyol 4200 is a polyether polyol that is suitable for combination with Desmodur in the formulation of solvent-free or low-solvent polyurethanes. It is suitable for combination with many Desmodur® products in the formulation of solvent-free elast...voir plus Acclaim® Polyol 4200 is a polyether polyol that is suitable for combination with Desmodur in the formulation of solvent-free or low-solvent polyurethanes. It is suitable for combination with many Desmodur® products in the formulation of solvent-free elastic coatings, adhesives and sealants. Acclaim® Polyol 4200 can be thinned with solvents such as esters, ketones and aromatics. Only PU grade solvents should be used (< 0.05% by wt. water). voir moins | |
| Baybond® PU 130 | Covestro | Baybond® PU 130 has anionic/non-ionic crosslinking polyether urethane polymer, used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing, and is useful for the sizing of glass fibers u...voir plus Baybond® PU 130 has anionic/non-ionic crosslinking polyether urethane polymer, used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing, and is useful for the sizing of glass fibers used to reinforce thermoplastics, especially polyamide. Glass fiber sizes based on Baybond® PU 130 have excellent filmforming properties and adhesion. This product also exhibits very good colorfastness at high temperatures and is also highly resistant to hydrolysis. Full mechanical properties of Baybond® PU 130 are developed by post-crosslinking for 20 minutes @ 170C. As with any product, use of Baybond® PU 130 in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Baybond® PU 330 | Covestro | Baybond® PU 330 has anionic, non-ionic polyester urethane polymer, used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing, especially for glass fibers used to reinforce thermosets. G...voir plus Baybond® PU 330 has anionic, non-ionic polyester urethane polymer, used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing, especially for glass fibers used to reinforce thermosets. Glass fiber sizes based on Baybond® PU 330 have excellent filmforming properties and adhesion. This product also remains stable when exposed to shear forces. As with any product, use of Baybond® PU 330 in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Baybond® PU 401 A | Covestro | Baybond® PU 401 A has anionic, non-ionic polyester urethane polymer, used as the film-forming component in glass fiber sizes. Commonly used as the film-forming component in glass fiber sizing. Glass fiber sizes based on its polyurethane dispersion have ex...voir plus Baybond® PU 401 A has anionic, non-ionic polyester urethane polymer, used as the film-forming component in glass fiber sizes. Commonly used as the film-forming component in glass fiber sizing. Glass fiber sizes based on its polyurethane dispersion have excellent film-forming properties and very good adhesion. As with any product, use of Baybond® PU 401 A polyurethane dispersion in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Baybond® PU 402 A | Covestro | Baybond® PU 402 A has anionic/non-ionic polyester urethane polymer used as the film-forming component in glass fiber sizes. It was developed for the sizing of glass fibers used to reinforce thermoplastics, particularly polyamide. Glass fiber sizes based o...voir plus Baybond® PU 402 A has anionic/non-ionic polyester urethane polymer used as the film-forming component in glass fiber sizes. It was developed for the sizing of glass fibers used to reinforce thermoplastics, particularly polyamide. Glass fiber sizes based on Baybond® PU 402 A are characterized by their outstanding film-forming properties and very good adhesion. They have high colorfastness, even at elevated temperatures. Baybond® PU 402 A is also very stable against shear forces. As with any product, use of Baybond® PU 402 A in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability voir moins | |
| Baybond® PU 403 | Covestro | Baybond® PU 403 has anionic, non-ionic polyester urethane polymer, used as the film forming component in glass fiber sizes. Its polyurethane disperson is commonly used as the film-forming component in glass fiber sizing. Glass fiber sizes based on Baybond...voir plus Baybond® PU 403 has anionic, non-ionic polyester urethane polymer, used as the film forming component in glass fiber sizes. Its polyurethane disperson is commonly used as the film-forming component in glass fiber sizing. Glass fiber sizes based on Baybond PU® 403 have excellent film-forming properties, and very good adhesion. The mechanical properties of Baybond® PU 403 are improved by post-curing at 150ºC or above for 30 minutes. As with any product, Baybond® PU 403 polyurethane dispersion in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Baybond® PU 405 | Covestro | Baybond® PU 405 has anionic/non-ionic cross linking polyether urethane polymer used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing, and is useful for the sizing of glass fibers us...voir plus Baybond® PU 405 has anionic/non-ionic cross linking polyether urethane polymer used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing, and is useful for the sizing of glass fibers used to reinforce thermoplastics, especially polyamide. Glass fiber sizes based on Baybond® PU 405 have excellent filmforming properties, adhesion and colorfastness. This product is also highly resistant to the effects of shear forces and hydrolysis. Full mechanical properties of Baybond® PU 405 are developed by post-crosslinking for 20 minutes @ 170°C. As with any product, use of Baybond® PU 405 in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Baybond® PU 406 | Covestro | Baybond® PU 406 is a non-ionic polyurethane polymer used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing. It is also useful for the sizing of glass fibers used to reinforce thermop...voir plus Baybond® PU 406 is a non-ionic polyurethane polymer used as the film-forming component in glass fiber sizes. It is commonly used as the filmforming component in glass fiber sizing. It is also useful for the sizing of glass fibers used to reinforce thermoplastics and has excellent film-forming properties and adhesion. Baybond® PU 406 also remains stable when exposed to shear forces. As with any product, use of Baybond® PU 406 in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Baybond® XL 825 | Covestro | Baybond® XL 825 is a waterbased aliphatic blocked polyisocyanate that is suitable for use as a crosslinker for glassfiber sizings. This product non-volatile content (0.9 - 1.1g / 1h / 125°C,convection oven) 30 ± 1, a flow time at 23°C, (4mmcup) of 10 - 5...voir plus Baybond® XL 825 is a waterbased aliphatic blocked polyisocyanate that is suitable for use as a crosslinker for glassfiber sizings. This product non-volatile content (0.9 - 1.1g / 1h / 125°C,convection oven) 30 ± 1, a flow time at 23°C, (4mmcup) of 10 - 55 , and a pH value at 20°C (supply form) of 7-8. Baybond® XL 825 was developed as crosslinker for the sizing of glass fibers used in combination with Baybond binders to reinforce thermoplastics, particularly polyamide. Glass fiber sizes based on Baybond® XL 825 are characterized by their good colorfastness, even at elevated temperatures. The mechanical film properties of sizings based on Baybond® XL 825 are developed fully by postcrosslinking at temperatures from 170°C for a duration of 20 minutes. The product is compatible with the additives normally used in the formulation of glass sizes, e.g. adhesion promoters, lubricants, antistatic agents and plasticizers. voir moins | |
| Baybond® XP 2728 | Covestro | Baybond® XP 2728 is a anionic/non-ionic polycarbonate-polyether urethane polymer used as the film-forming component in glass fiber sizes. It was developed for the sizing of glass fibers used to reinforce thermoplastics, particularly polyamide. Glass fiber...voir plus Baybond® XP 2728 is a anionic/non-ionic polycarbonate-polyether urethane polymer used as the film-forming component in glass fiber sizes. It was developed for the sizing of glass fibers used to reinforce thermoplastics, particularly polyamide. Glass fiber sizes based on Baybond® XP 2728 are characterized by their outstanding film-forming properties and very good adhesion. Baybond® XP 2728 exhibits outstanding hydrolysis resistance and colorfastness, and is also very stable against shear forces. As with any product, use of Baybond® XP 2728 in a given application must be tested (including but not limited to field testing) in advance by the user to determine suitability. voir moins | |
| Bayhydrol® A 242 | Covestro | Bayhydrol® A 242 is a polyacrylic resin used as a coreactant for Bayhydur® and Desmodur® N polyisocyanates in the formulation of aqueous two component polyurethane systems for various applications by brush, roller or spray. | |
| Bayhydrol® HD 2016 | Covestro | Bayhydrol® HD 2016 is a co-solvent free hydroxyl functional acrylic resin dispersed in water. It is used as a coreactant for Bayhydur water-dispersible polyisocyanates in the formulation of < 50g/l VOC coatings. This product can also be combined with othe...voir plus Bayhydrol® HD 2016 is a co-solvent free hydroxyl functional acrylic resin dispersed in water. It is used as a coreactant for Bayhydur water-dispersible polyisocyanates in the formulation of < 50g/l VOC coatings. This product can also be combined with other water-reducible binders. voir moins | |
| Bayhydrol® HD 2017 | Covestro | Bayhydrol® HD 2017 is a hydroxyl-functional acrylic resin dispersed in water with approximately 1% co-solvent. It can be used as a coreactant for Bayhydur® water-dispersible polyisocyanates in the formulation of < 50g/l VOC coatings. | |
| Bayhydrol® PR 435 | Covestro | Bayhydrol® PR 435 is an aqueous aliphatic polyurethane dispersion that contains only 5% by weight of organic cosolvent. | |
| Bayhydrol® UV 2280 | Covestro | Bayhydrol® UV 2280 is a urethane acrylate dispersion. It is supplied as approximately 39% solids dispersion in water. It may be used in the formulation of aqueous UV-curing coatings, especially for applica- tion on wood/wood materials. Generally speaking,...voir plus Bayhydrol® UV 2280 is a urethane acrylate dispersion. It is supplied as approximately 39% solids dispersion in water. It may be used in the formulation of aqueous UV-curing coatings, especially for applica- tion on wood/wood materials. Generally speaking, the coated surfaces can be sanded before UV curing. Additions of 1.0 to 2.5% by weight photoinitiator, calculated on the solid binder, have proved suitable for initiating the curing reaction. voir moins | |
| Bayhydur® 304 | Covestro | Bayhydur® 304 is a hydrophilically modified, aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). It is primarily used as the crosslinker for aqueous polyol binders (Bayhydrol). | |
| Bayhydur® 305 | Covestro | Bayhydur® 305 is a hydrophilic aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). It is a crosslinker for aqueous coatings, developed specially for trade applications where the ease of mixing the hardener by shaking or manual stirring is ...voir plus Bayhydur® 305 is a hydrophilic aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). It is a crosslinker for aqueous coatings, developed specially for trade applications where the ease of mixing the hardener by shaking or manual stirring is a key requirement. voir moins | |
| Bayhydur® 401-70 | Covestro | Bayhydur® 401-70 is a water-dispersible polyisocyanate based on Isophorone Diisocyanate (IPDI) and dissolved in 1-methoxypropylacetate-2/xylene, 1:1. It is mainly used as the co-reactant for aqueous polyol binders from the Bayhydrol range. | |
| Bayhydur® BL XP 2706 | Covestro | Bayhydur® BL XP 2706 is a reactive, blocked aliphatic polyisocyanate. Form supplied is approximately 40% in water (neutralized with 2.8 pts. dimethyl ethanol amine). It is used primarily in combination with Bayhydrol® polyols for the formulation of water...voir plus Bayhydur® BL XP 2706 is a reactive, blocked aliphatic polyisocyanate. Form supplied is approximately 40% in water (neutralized with 2.8 pts. dimethyl ethanol amine). It is used primarily in combination with Bayhydrol® polyols for the formulation of water-reducible, lightfast, one-component polyurethane baking coatings. It is also used as an additive in waterborne baking systems to improve hardness, impact strength, chemical resistance and adhesion. voir moins | |
| Bayhydur® XP 2487/1 | Covestro | Bayhydur® XP 2487/1 is a water-dispersible polyisocyanate based on hexamethylene diisocyanate (HDI). It is a solvent-free crosslinking agent for two-component waterborne polyurethane coatings. | |
| Bayhydur® XP 2547 | Covestro | Bayhydur® XP 2547 is a water-dispersible polyisocyanate based on hexamethylene diisocyanate (HDI). It is a solvent-free crosslinking agent for two-component waterborne polyurethane coatings. Suitable coreactants are hydroxyl-functional waterborne resins s...voir plus Bayhydur® XP 2547 is a water-dispersible polyisocyanate based on hexamethylene diisocyanate (HDI). It is a solvent-free crosslinking agent for two-component waterborne polyurethane coatings. Suitable coreactants are hydroxyl-functional waterborne resins such as Bayhydrol® XP 2542. voir moins | |
| Bayhydur® XP 2655 | Covestro | Bayhydur® XP 2655 is a hydrophilic aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). It is used as a hardener for waterborne two-component polyurethane systems and a crosslinking agent for waterborne systems from which reliable incorpora...voir plus Bayhydur® XP 2655 is a hydrophilic aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). It is used as a hardener for waterborne two-component polyurethane systems and a crosslinking agent for waterborne systems from which reliable incorporation and high chemical resistances are required. voir moins | |
| Bayhydur® XP 2700 | Covestro | Bayhydur® XP 2700 is a hydrophilic aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). Form supplied is approximately 65% in dipropylene glycol dimethyl ether. It is a crosslinker for aqueous coatings, developed specially for trade applica...voir plus Bayhydur® XP 2700 is a hydrophilic aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI). Form supplied is approximately 65% in dipropylene glycol dimethyl ether. It is a crosslinker for aqueous coatings, developed specially for trade applications where the ease of mixing the hardener by manual stirring is a key requirement. voir moins | |
| Bayhytherm® 3146 | Covestro | Bayhytherm® 3146 is a water-reducible, aliphatic, self-crosslinking stoving urethane resin used as binder for waterborne, one-component stoving polyurethane systems. | |
| Baymedix® AP501 | Covestro | Baymedix® AP501 is an aliphatic NCO-terminated prepolymer based on hexamethylene diisocyanate. | |
| Baymedix® AR602 | Covestro | Baymedix® AR602 is a polyether polyol based on a tetra-functional starter molecule. | |
| Baymedix® CD102 | Covestro | Baymedix® CD102 is an aqueous polyurethane dispersion. | |
| Baymedix® CD104 | Covestro | Baymedix® CD104 is an aqueous polyurethane dispersion. | |
| Baymedix® FD103 | Covestro | Baymedix® FD103 is an aqueous polyurethane dispersion. | |
| Baymedix® FP503 | Covestro | Baymedix® FP503 is an aliphatic, hydrophilic NCO prepolymer blend based on hexamethylene diisocyanate (HDI). | |
| CUMAR® 105 | Neville Chemical Company | CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne ...voir plus CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne and epoxy based coatings, IV ink modifiers, adhesives and sealants. voir moins | |
| Desmodur® BL 1100/1 | Covestro | Desmodur® BL 1100/1 is a blocked aromatic polyisocyanate based on TDI, supplied as solvent-free. It is combined with cycloaliphatic diamines to formulate highly flexible, one-component stoving coatings, including those for application by dipping and curta...voir plus Desmodur® BL 1100/1 is a blocked aromatic polyisocyanate based on TDI, supplied as solvent-free. It is combined with cycloaliphatic diamines to formulate highly flexible, one-component stoving coatings, including those for application by dipping and curtain coating and adhesive cements. voir moins | |
| Desmodur® BL 3272 MPA | Covestro | Desmodur® BL 3272 MPA is a blocked aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI) and dissolved in propylene glycol monomethyl ether acetate(MPA/PMA). It was developed as a hardener for lightfast one-pack baking polyurethane coatings w...voir plus Desmodur® BL 3272 MPA is a blocked aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI) and dissolved in propylene glycol monomethyl ether acetate(MPA/PMA). It was developed as a hardener for lightfast one-pack baking polyurethane coatings whose baking temperature can be reduced by the addition of a catalyst, e.g. 0.3 - 1.0 % DBTL, without influencing the storage stability of the ready-to-use formulation. voir moins | |
| Desmodur® BL 3370 MPA | Covestro | Desmodur® BL 3370 PMA is a blocked aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI) and dissolved in propylene glycol monomethyl ether acetate(MPA/PMA). It is used with hydroxyl functional coreactants in the formulation of light-stable o...voir plus Desmodur® BL 3370 PMA is a blocked aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI) and dissolved in propylene glycol monomethyl ether acetate(MPA/PMA). It is used with hydroxyl functional coreactants in the formulation of light-stable one-component baking systems with relatively low curing temperatures. Coatings based on Desmodur® BL 3370 MPA are used for the industrial finishing of appliances, coil coating, can coating, and in the automotive industry for chip-resistant primer-surfacers and topcoats. voir moins | |
| Desmodur® BL 3475 BA/SN | Covestro | Desmodur® BL 3475 BA/SN is a blocked aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI) and dissolved in n-butyl acetate and aromatic 100 (1:1). It was developed as a hardener for lightfast one-pack bakin...voir plus Desmodur® BL 3475 BA/SN is a blocked aliphatic polyisocyanate based on hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI) and dissolved in n-butyl acetate and aromatic 100 (1:1). It was developed as a hardener for lightfast one-pack baking polyurethane coatings with a low baking temperature. Used in the formulation of high-quality industrial coatings, especially for cans and tubes. The product can also be used as an additive to improve the reactivity, flexibility and adhesion of conventional baking systems. voir moins | |
| Desmodur® BL 4265 SN | Covestro | Desmodur® BL 4265 SN is a blocked aliphatic polyisocyanate based on isophorone diisocyanate (IPDI) and dissolved in aromatic 100. It is used with hydroxyl-functional coreactants in the formulation of light-stable one-component baking systems with relative...voir plus Desmodur® BL 4265 SN is a blocked aliphatic polyisocyanate based on isophorone diisocyanate (IPDI) and dissolved in aromatic 100. It is used with hydroxyl-functional coreactants in the formulation of light-stable one-component baking systems with relatively low curing temperatures. Coatings based on Desmodur® BL 4265 SN blocked polyisocyanate are used for the industrial finishing of appliances, coil coating, and can coating, and in the automotive industry for chip-resistant primer-surfacers and topcoats. voir moins | |
| Desmodur® BL 5375 | Covestro | Desmodur® BL 5375 is a blocked aliphatic crosslinking stoving urethane resin based on HMDI and dissolved in solvent naptha 100/1-methoxypropylacetate-2, 1:1. It was developed as a hardener component for lightfast one-pack stoving polyurethane systems. As ...voir plus Desmodur® BL 5375 is a blocked aliphatic crosslinking stoving urethane resin based on HMDI and dissolved in solvent naptha 100/1-methoxypropylacetate-2, 1:1. It was developed as a hardener component for lightfast one-pack stoving polyurethane systems. As with air-drying two-pack PU coatings, the film properties can be influenced by the crosslinking density and the selection of hydroxylbearing polyol co-reactant. voir moins | |
| Desmodur® E 1160 MPA/X | Covestro | Desmodur® E 1160 MPA/X is an aromatic prepolymer based on toluene diisocyanate (TDI). It is suitable for use in the following applications: wood coatings, e.g. for parquet flooring, wall and ceiling paneling, boats and furniture; impregnating agents for m...voir plus Desmodur® E 1160 MPA/X is an aromatic prepolymer based on toluene diisocyanate (TDI). It is suitable for use in the following applications: wood coatings, e.g. for parquet flooring, wall and ceiling paneling, boats and furniture; impregnating agents for mineral building material. Clear impregnating systems based on Desmodur® E 1160 MPA/X provide surfaces with long-term protection against moisture, oil, fuels, aggressive chemicals and chemical damage. voir moins | |
| Desmodur® E 14 | Covestro | Desmodur® E 14 is a solvent-free, linear aromatic prepolymer based on toluene diisocyanate (TDI). It is recommended for the formulation of both coatings and sealants. Combinations with Desmodur E 22 polyisocyanate yield highly flexible water-resistant fin...voir plus Desmodur® E 14 is a solvent-free, linear aromatic prepolymer based on toluene diisocyanate (TDI). It is recommended for the formulation of both coatings and sealants. Combinations with Desmodur E 22 polyisocyanate yield highly flexible water-resistant finishes and sprayable coatings. Desmodur E 14 can be used with amine crosslinkers to provide tough flexible films. voir moins | |
| Desmodur® E 21 | Covestro | Desmodur® E 21 is an aromatic polyisocyanate prepolymer based on diphenylmethane diisocyanate (MDI). It is a solvent-free liquid of medium viscosity. It is suitable for use in the formulation of moisture-curing, one-component systems which, when thinned w...voir plus Desmodur® E 21 is an aromatic polyisocyanate prepolymer based on diphenylmethane diisocyanate (MDI). It is a solvent-free liquid of medium viscosity. It is suitable for use in the formulation of moisture-curing, one-component systems which, when thinned with a suitable solvent, can be used as primers and sealers for porous substrates to provide protection against moisture, oil, fuel and other chemicals. It can also be used as a binder in the formulation of synthetic resin mortars. voir moins | |
| Desmodur® H | Covestro | Desmodur® H is a monomeric aliphatic diisocyanate. It is used mainly in the manufacture of polyisocyanates, for example, polyurethane coating raw materials. | |
| Desmodur® HL BA | Covestro | Desmodur® HL BA is an aliphatic/aromatic polyisocyanate copolymer based on toluene diisocyanate (TDI) and and hexamethylene diisocyanate (HDI) and dissolved in n-butyl acetate. Used in the formulation of fast-drying two-component coatings. Drying times of...voir plus Desmodur® HL BA is an aliphatic/aromatic polyisocyanate copolymer based on toluene diisocyanate (TDI) and and hexamethylene diisocyanate (HDI) and dissolved in n-butyl acetate. Used in the formulation of fast-drying two-component coatings. Drying times of coatings using Desmodur® HL BA are considerably shorter than those of coatings based on Desmodur® CB polyisocyanates and somewhat longer than those based on Desmodur® IL polyisocyanate. voir moins | |
| Desmodur® I | Covestro | Desmodur® I is a monomeric cycloaliphatic diisocyanate. It is also known as 3-isocyanatomethyl-3, 5,5-trimethylcyclohexyl isocyanate or IPDI. It is useful as a reactive building block for the preparation of chemical products, reactive intermediates and po...voir plus Desmodur® I is a monomeric cycloaliphatic diisocyanate. It is also known as 3-isocyanatomethyl-3, 5,5-trimethylcyclohexyl isocyanate or IPDI. It is useful as a reactive building block for the preparation of chemical products, reactive intermediates and polymers. The isocyanate groups present in Desmodur® I diisocyanate can undergo addition reactions at room temperature with compounds which contain active hydrogens, making it a valuable organic intermediate. The difference in reactivity between the isocyanate groups in Desmodur® I diisocyanate is especially useful in the preparation of polyurethane products. voir moins | |
| Desmodur® IL 1351 51% BA | Covestro | Desmodur® IL 1351 51% BA is an aromatic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 51% in butyl acetate. Can be used in combination with Desmophen® 1300 for the formulation of very fast drying, two-component polyurethane ...voir plus Desmodur® IL 1351 51% BA is an aromatic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 51% in butyl acetate. Can be used in combination with Desmophen® 1300 for the formulation of very fast drying, two-component polyurethane coatings. Such systems are used in the furniture industry, among others, where very short drying times and early sandability are required. voir moins | |
| Desmodur® IL 1451 | Covestro | Desmodur® IL 1451 is an aromatic polyisocyanate based on toluene diisocyanate (TDI) and dissolved in n-butyl acetate. Two-pack polyurethane coatings based on Desmodur® IL 1451 are characterized by their rapid initial drying and early sandability. This is ...voir plus Desmodur® IL 1451 is an aromatic polyisocyanate based on toluene diisocyanate (TDI) and dissolved in n-butyl acetate. Two-pack polyurethane coatings based on Desmodur® IL 1451 are characterized by their rapid initial drying and early sandability. This is most important in industrial wood and furniture finishing. voir moins | |
| Desmodur® IL BA | Covestro | Desmodur® IL BA is an aromatic polyisocyanate based on toluene diisocyanate (TDI) and dissolved in n-butyl acetate. Used in the formulation of fast drying two-component clear and pigmented polyurethane coatings for wood, metal, and paper substrates. Coati...voir plus Desmodur® IL BA is an aromatic polyisocyanate based on toluene diisocyanate (TDI) and dissolved in n-butyl acetate. Used in the formulation of fast drying two-component clear and pigmented polyurethane coatings for wood, metal, and paper substrates. Coatings based on Desmodur® IL BA lend themselves to applications requiring high production rates and fast dry-to-handle times. Wood coatings formulated with Desmodur® IL BA show quick sanding properties. The applied finishes show little tendency to run from sharp edges. voir moins | |
| Desmodur® IL EA | Covestro | Desmodur® IL EA is an aromatic polyisocyanate resin based on toluene diisocyanate (TDI). Form supplied is approximately 51 % in ethyl acetate. Can be used as a hardener component for fast-drying, two-component polyurethane coatings. It can also be used i...voir plus Desmodur® IL EA is an aromatic polyisocyanate resin based on toluene diisocyanate (TDI). Form supplied is approximately 51 % in ethyl acetate. Can be used as a hardener component for fast-drying, two-component polyurethane coatings. It can also be used in combination with various Baycoll® products or other hydroxyl-bearing substances to formulate adhesives. Because of its fast drying, Desmodur IL EA is mainly used in coatings for on-line applications, like the packaging industry or in industrial furniture finishing. voir moins | |
| Desmodur® L 67 BA | Covestro | Desmodur® L 67 BA is an aromtic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 67% in butyl acetate. Can be used in combination with various Desmophen® grades or other hydroxyl-bearing substances to formulate air-drying two-c...voir plus Desmodur® L 67 BA is an aromtic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 67% in butyl acetate. Can be used in combination with various Desmophen® grades or other hydroxyl-bearing substances to formulate air-drying two-component polyurethane coatings. Systems crosslinked with Desmodur® L 67 BA can be used as coatings for furniture, parquet flooring, metal, paper, plastics and mineral substrates. voir moins | |
| Desmodur® L 67 MPA/X | Covestro | Desmodur® L 67 MPA/X is an aromtic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 67% in 1-methoxypropylacetate-2/xylene (1:1). Can be used in combination with various Desmophen® grades or other hydroxylbearing substances to ...voir plus Desmodur® L 67 MPA/X is an aromtic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 67% in 1-methoxypropylacetate-2/xylene (1:1). Can be used in combination with various Desmophen® grades or other hydroxylbearing substances to formulate air-drying twocomponent polyurethane coatings. Systems crosslinked with Desmodur® L 67 MPA/X can be used as coatings for furniture, parquet flooring, metal, paper, plastics and mineral substrates. voir moins | |
| Desmodur® L 75 | Covestro | Desmodur® L 75 is an aromatic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 75% in ethyl acetate. Can be used in combination with various Desmophen®, Baycoll®, Desmocoll® grades or other hydroxyl-bearing substances to formul...voir plus Desmodur® L 75 is an aromatic polyisocyanate based on toluene diisocyanate. Form supplied is approximately 75% in ethyl acetate. Can be used in combination with various Desmophen®, Baycoll®, Desmocoll® grades or other hydroxyl-bearing substances to formulate air-drying two-component polyurethane coatings and adhesives. Systems crosslinked with Desmodur L 75 can be used as coatings for furniture, parquet flooring, metal, paper, plastics and mineral substrates. It is also suitable for room-temperature crosslinking of adhesives based on Desmocoll® or Baycoll®. These can be used to bond many materials,e.g. wood, metal and plastic. voir moins | |
| Desmodur® N 100 | Covestro | Desmodur® N 100 is a solvent-free, aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Recommended for use in two-component clear and pigmented interior and exterior finishes. Coatings based on Desmodur N 100, exhibit excellent gloss...voir plus Desmodur® N 100 is a solvent-free, aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Recommended for use in two-component clear and pigmented interior and exterior finishes. Coatings based on Desmodur N 100, exhibit excellent gloss retention and weather resistance when formulated with proper hydroxyl-functional coreactants. These coatings also have very good resistance to solvents, chemicals, and abrasion. voir moins | |
| Desmodur® N 100A | Covestro | Desmodur® N 100A is a solvent-free, aliphatic polyisocyanate (HDI biuret). | |
| Desmodur® N 3200 | Covestro | Desmodur® N 3200 is a solvent free aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Coatings formulated with Desmodur® N 3200 polyisocyanate show the same final properties as those based on Desmodur® N 100. It is particularly suit...voir plus Desmodur® N 3200 is a solvent free aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Coatings formulated with Desmodur® N 3200 polyisocyanate show the same final properties as those based on Desmodur® N 100. It is particularly suitable for the formulation of high-solids two-component coating materials for a variety of applications. voir moins | |
| Desmodur® N 3200A | Covestro | Desmodur® N 3200A is a solvent free aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). | |
| Desmodur® N 3400 | Covestro | Desmodur® N 3400 is a solvent free low viscosity aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Can be used as a hardener or reactive diluent for 100% solids, solvent-borne and aqueous, two-pack polyurethane coatings. Depending ...voir plus Desmodur® N 3400 is a solvent free low viscosity aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Can be used as a hardener or reactive diluent for 100% solids, solvent-borne and aqueous, two-pack polyurethane coatings. Depending on the polyol used, the coatings yield tough but flexible films that can be either soft or extremely hard, have good resistance to chemicals and solvents, good weather stability and good resistance to abrasion. voir moins | |
| Desmodur® N 3600 | Covestro | Desmodur® N 3600 is a low viscosity solvent-free polyfunctional aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Used primarily as the hardener component for light- fast two-pack polyurethane coatings with high resistance to chemi...voir plus Desmodur® N 3600 is a low viscosity solvent-free polyfunctional aliphatic polyisocyanate resin based on hexamethylene diisocyanate (HDI). Used primarily as the hardener component for light- fast two-pack polyurethane coatings with high resistance to chemicals and weathering, very good gloss retention and outstanding mechanical properties. The main applications for systems based on Desmodur® N 3600 are air and force drying coatings for automotive OEM, automotive refinishing, transportation, industrial finishing and plastics. voir moins | |
| Desmodur® N 3790 BA | Covestro | Desmodur® N 3790 BA is an aliphatic polyisocyanate (high functional HDI trimer) supplied at 90% solids in n-butyl acetate. Used primarily as the hardener component for lightfast two-pack polyurethane coatings with high resistance to chemicals and weatheri...voir plus Desmodur® N 3790 BA is an aliphatic polyisocyanate (high functional HDI trimer) supplied at 90% solids in n-butyl acetate. Used primarily as the hardener component for lightfast two-pack polyurethane coatings with high resistance to chemicals and weathering, very good gloss retention and outstanding mechanical properties. The main applications for systems based on Desmodur® N 3790 BA are air and force-drying coatings for automotive OEM, automotive refinishing, transportation, industrial finishing and plastics. voir moins | |
| Desmodur® N 3800 | Covestro | Desmodur® N 3800 is a solvent free flexibilizing aliphatic polyisocyanate. In combination with suitable polyols, it can be used in the formulation of highly flexible coatings that are stable to accelerated and outdoor weathering. These can be used for coa...voir plus Desmodur® N 3800 is a solvent free flexibilizing aliphatic polyisocyanate. In combination with suitable polyols, it can be used in the formulation of highly flexible coatings that are stable to accelerated and outdoor weathering. These can be used for coating plastics. The use of Desmodur® N 3800 as a combination hardener component makes it possible to adjust the flexibility of the polyol mill base. The product can also be used as a flexibilizing component in other applications, e.g. stone-chip protection systems, vehicle repair systems. voir moins | |
| Desmodur® N 75 MPA/X | Covestro | Desmodur® N 75 MPA/X is an aliphatic polyisocyanate that acts as the hardener component for lightfast polyurethane coating systems. | |
| Desmodur® W | Covestro | Desmodur® W is a liquid cycloaliphatic diisocyanate used as a reactive building block for the preparation of chemical products, reactive intermediates and polymers. | |
| Desmodur® Z 4470 BA | Covestro | Desmodur® Z 4470 BA is an aliphatic polyisocyanate for use as the hardener component for lightfast polyurethane coating systems and as an additive resin for alkyd spray coatings. | |
| Desmodur® Z 4470 MPA/X | Covestro | Desmodur® Z 4470 MPA/X is an aliphatic polyisocyanate for use as the hardener component for lightfast polyurethane coating systems and as an additive resin for alkyd spray coatings. | |
| Desmodur® Z 4470 SN | Covestro | Desmodur® Z 4470 SN is an aliphatic polyisocyanate based on isophorone diisocyanate and dissolved in aromatic 100. Has better solubility and compatibility. Mainly used as an additive resin to accelerate drying, curing and chemical crosslinking. | |
| Desmodur® Z 4470 SN/BA | Covestro | Desmodur® Z 4470 SN/BA is an aliphatic polyisocyanate based on isophorone diisocyanate dissolved in Aromatic 100 and n-butyl acetate. Better solubility and compatibility. Mainly used as an additive resin to accelerate drying, curing and chemical crossl...voir plus Desmodur® Z 4470 SN/BA is an aliphatic polyisocyanate based on isophorone diisocyanate dissolved in Aromatic 100 and n-butyl acetate. Better solubility and compatibility. Mainly used as an additive resin to accelerate drying, curing and chemical crosslinking. voir moins | |
| Desmophen® 1300 BA | Covestro | Desmophen® 1300 BA is a polyester polyol. Form supplied is approximately 75% in butyl acetate. This polyester is mainly used as the co-reactant for polyisocyanates in the formulation of fast-drying, two-pack coatings. They are mainly used for clear and p...voir plus Desmophen® 1300 BA is a polyester polyol. Form supplied is approximately 75% in butyl acetate. This polyester is mainly used as the co-reactant for polyisocyanates in the formulation of fast-drying, two-pack coatings. They are mainly used for clear and pigmented finishes for wood, chipboard and hardboard. voir moins | |
| Desmophen® 1300 X | Covestro | Desmophen® 1300 X polyester is mainly used as the co-reactant for polyisocyanates in the formulation of fast-drying, two-pack coatings. They are mainly used as clear and pigmented finishes for wood, chipboard and hardboard. Desmophen 1300 X is a polyester...voir plus Desmophen® 1300 X polyester is mainly used as the co-reactant for polyisocyanates in the formulation of fast-drying, two-pack coatings. They are mainly used as clear and pigmented finishes for wood, chipboard and hardboard. Desmophen 1300 X is a polyester polyol, and the form supplied is approximately 75% in xylene. voir moins | |
| Desmophen® 631 MPA | Covestro | Desmophen® 631 MPA is a saturated polyester resin. | |
| Desmophen® 650 MPA | Covestro | Desmophen® 650 MPA is a branched, hydroxyl-bearing polyester used as a co-reactant, usually with Desmodur N 75, in the formulation of lightfast and weather-stable, two-pack polyurethane coatings. | |
| Desmophen® 650A 65 PMA | Covestro | Desmophen® 650A 65 PMA is a saturated polyester resin that is used as a coreactant for Desmodur N polyisocyanates two-component polyurethane coatings. | |
| Desmophen® 651 MPA | Covestro | Desmophen® 651 MPA is a branched hydroxyl-bearing polyester used as a co-reactant, usually with Desmodur N 75, in the formulation of lightfast and weather-stable two-pack coatings. | |
| Desmophen® 670 BA | Covestro | Desmophen® 670 BA is a slightly branched, hydroxyl- bearing polyester. Form supplied is approximately 80% in butyl acetate. Desmophen® 670 BA is used primarily in the formulation of weather-stable flexible coatings. | |
| Desmophen® C 1100 | Covestro | Desmophen® C 1100 is a linear aliphatic polycarbonate polyester based on hexane diol-1,6 E-caprolactone with an average molecular weight of approximately 1,000. It is a solvent-free medium viscosity liquid used for high-grade building blocks for a variet...voir plus Desmophen® C 1100 is a linear aliphatic polycarbonate polyester based on hexane diol-1,6 E-caprolactone with an average molecular weight of approximately 1,000. It is a solvent-free medium viscosity liquid used for high-grade building blocks for a variety of polyurethane systems. Applications for Desmophen® C 1100 include both interior and exterior applications with very good weatherability, lightfastness, hydrolytic stability and elasticity. voir moins | |
| Desmophen® C 1200 | Covestro | Desmophen® C 1200 is a linear aliphatic polycarbonate polyester based on hexane diol-1,6 E-caprolactone with an average molecular weight of approximately 2,000. It is a solvent-free medium viscosity liquid used for binder for high-grade flexible coatings...voir plus Desmophen® C 1200 is a linear aliphatic polycarbonate polyester based on hexane diol-1,6 E-caprolactone with an average molecular weight of approximately 2,000. It is a solvent-free medium viscosity liquid used for binder for high-grade flexible coatings and sealers. Possible applications include decorative coatings, sealing compounds and joint sealants. voir moins | |
| Desmophen® C 2100 | Covestro | Desmophen® C 2100 is a linear hydroxyl-terminated, aliphatic polycarbonate diol with an average molecular weight of approximately 1,000. It is solvent free and waxy at room temperature. It can be used in high-grade building blocks for a variety of polyur...voir plus Desmophen® C 2100 is a linear hydroxyl-terminated, aliphatic polycarbonate diol with an average molecular weight of approximately 1,000. It is solvent free and waxy at room temperature. It can be used in high-grade building blocks for a variety of polyurethane systems with very good weatherability, lightfastness and hydrolytic stability. voir moins | |
| Desmophen® C 2200 | Covestro | Desmophen® C 2200 is a linear hydroxyl-terminated, aliphatic polycarbonate diol with an average molecular weight of approximately 2,000. It is a polyurethane raw material for applications highly resistant to hydrolysis and hot air. It can be used as a co...voir plus Desmophen® C 2200 is a linear hydroxyl-terminated, aliphatic polycarbonate diol with an average molecular weight of approximately 2,000. It is a polyurethane raw material for applications highly resistant to hydrolysis and hot air. It can be used as a component of polyurethane dispersions, for thermoplastic polyurethanes, casting elastomers, textile coatings and adhesives. It is characterized by lightfastness and high resistance to hydrolysis and hot air. voir moins | |
| Desmophen® NH 1220 | Covestro | Desmophen® NH 1220 resin is a solvent-free, aminefunctional reactive partner for polyisocyanates, and is a low viscosity amine-functional resin developed for use in the formulation of high solids two component polyurethane/ polyurea coatings. Desmophen® N...voir plus Desmophen® NH 1220 resin is a solvent-free, aminefunctional reactive partner for polyisocyanates, and is a low viscosity amine-functional resin developed for use in the formulation of high solids two component polyurethane/ polyurea coatings. Desmophen® NH 1220 resin may be used by itself or as a blend with hydroxyfunctional acrylic resins and crosslinked with an aliphatic polyisocyanate to yield high solids polyurethane/ urea clearcoats. voir moins | |
| Desmophen® NH 1420 | Covestro | Desmophen® NH 1420 resin is a solvent-free, amine-functional reactive partner for polyisocyanates, and is a low viscosity amine functional resin developed for use in the formulation of high solids two-component polyurethane/urea coatings. Desmophen® NH 14...voir plus Desmophen® NH 1420 resin is a solvent-free, amine-functional reactive partner for polyisocyanates, and is a low viscosity amine functional resin developed for use in the formulation of high solids two-component polyurethane/urea coatings. Desmophen® NH 1420 resin may be used by itself or as a blend with hydroxy-functional acrylic resins and crosslinked with an aliphatic polyisocyanate to yield high solids polyurethane/urea clearcoats. voir moins | |
| Desmophen® NH 1520 | Covestro | Desmophen® NH 1520 resin is an amine-functional used as a reactive partner for polyisocyanates. Desmophen® NH 1520 resin is a low viscosity amine-functional resin developed for use in the formulation of high solids two component polyurethane/ polyurea co...voir plus Desmophen® NH 1520 resin is an amine-functional used as a reactive partner for polyisocyanates. Desmophen® NH 1520 resin is a low viscosity amine-functional resin developed for use in the formulation of high solids two component polyurethane/ polyurea coatings. Desmophen® NH 1520 resin may be used by itself or as a blend with hydroxyfunctional acrylic resins and crosslinked with an aliphatic polyisocyanate to yield high solids polyurethane/ urea clearcoats. voir moins | |
| Desmophen® NH 1521 | Covestro | Desmophen® NH 1521 resin is an amine-functional reactive partner for polyisocyanates, supplied with 10% n-butyl acetate. Desmophen® NH 1521 resin is a low viscosity amine-functional resin developed for use in the formulation of high solids two component ...voir plus Desmophen® NH 1521 resin is an amine-functional reactive partner for polyisocyanates, supplied with 10% n-butyl acetate. Desmophen® NH 1521 resin is a low viscosity amine-functional resin developed for use in the formulation of high solids two component polyurethane/ polyurea coatings. Desmophen® NH 1521 resin may be used by itself or as a blend with hydroxyfunctional acrylic resins and crosslinked with an aliphatic polyisocyanate to yield high solids polyurethane/ urea clearcoats. voir moins | |
| Desmotherm® 2170 | Covestro | Desmotherm® 2170 is an aromatic, self-crosslinking, stoving urethane resin. Used as a binder for one-pack stoving polyurethane systems. | |
| Dynasylan® 1124 | Evonik Operations GmbH, BL Silanes | Dynasylan® 1124 is a secondary aminofunctional methoxy-silane. The product acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers). It can also be us...voir plus Dynasylan® 1124 is a secondary aminofunctional methoxy-silane. The product acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers). It can also be used for the chemical modification of polymers and isocyanates. voir moins | |
| DYNASYLAN® 1146 | Evonik Operations GmbH, BL Silanes | Hydrophobic Dynasylan® 1146 diaminofunctional silane is used in adhesives and sealants, and in coatings, to improve the adhesion of amino-reactive resins (e.g. RTV-silicones, two-part urethanes, silylated urethanes, MS polymers, and two-part epoxies) to i...voir plus Hydrophobic Dynasylan® 1146 diaminofunctional silane is used in adhesives and sealants, and in coatings, to improve the adhesion of amino-reactive resins (e.g. RTV-silicones, two-part urethanes, silylated urethanes, MS polymers, and two-part epoxies) to inorganic surfaces, plastic surfaces, and inorganic fillers. Dynasylan® 1146 silane is characterized by randomly distributed linear and cyclic oligosiloxanes and it fulfills the OECD polymer definition. Its low volatility and viscosity make compounding easy. Dynasylan® 1146 silane produces significantly less by-product (VOC) and has a correspondingly low odor level during application. voir moins | |
| Dynasylan® 40 | Evonik Operations GmbH, BL Silanes | Dynasylan® 40 is a ethyl silicate with a silicon dioxide content of approximately 40 - 42 % upon complete hydrolysis (the Si content of Dynasylan® 40 is calculated as SiO2). Dynasylan® 40 is formed in the presence of water from tetraethyl silicate (Si[OEt...voir plus Dynasylan® 40 is a ethyl silicate with a silicon dioxide content of approximately 40 - 42 % upon complete hydrolysis (the Si content of Dynasylan® 40 is calculated as SiO2). Dynasylan® 40 is formed in the presence of water from tetraethyl silicate (Si[OEt]4) by partial hydrolysis of the ethoxy groups to hydroxyl groups and subsequent condensation with formation of siloxane bonds (-Si-O-Si-). Dynasylan® 40 is a colorless, low-viscosity liquid with an SiO2 content of 40% (the Si content of Dynasylan® 40 is calculated as SiO2). The polysilicic acids still have a sufficient content of ethoxy groups which can be activated by acid- or base-catalyzed hydrolysis. Condensation starts even during hydrolysis, with the formation of relatively large polymeric molecules. During storage of these hydrolysates, condensation continues until a gel is formed, where the rate depends on the degree of hydrolysis. The action of the hydrolysates as binders is based on the continuation of the hydrolysis with subsequent gelation and dehydration to give polymeric SiO2 structures. voir moins | |
| Dynasylan® 4148 | Evonik Operations GmbH, BL Silanes | Dynasylan® 4148 is a ready-to-use silane, soluble in water and most organic solvents. Dynasylan® 4148 is a rheological additive which reduces the viscosity of highly-filled polymer systems, like aluminum trihydroxide-filled polyesters or SMC-pastes. Contr...voir plus Dynasylan® 4148 is a ready-to-use silane, soluble in water and most organic solvents. Dynasylan® 4148 is a rheological additive which reduces the viscosity of highly-filled polymer systems, like aluminum trihydroxide-filled polyesters or SMC-pastes. Contrary to most other organofunctional silanes, Dynasylan® 4148 features chemical polarity but has a non-reactive polar group. Furthermore, Dynasylan® 4148 can be used as anti-settling agent for fillers and pigments in paints as well as corrosion inhibitors in glycol based cooling agents. voir moins | |
| Dynasylan® 6490 | Evonik Operations GmbH, BL Silanes | Dynasylan® 6490 is a vinyl silane concentrate (oligomeric siloxane) containing vinyl and methoxy groups. Dynasylan® 6490 is a colourless, nearly odorless low-viscosity liquid. Dynasylan® 6490 is an excellent compatibiliser between inorganic fillers (e.g. ...voir plus Dynasylan® 6490 is a vinyl silane concentrate (oligomeric siloxane) containing vinyl and methoxy groups. Dynasylan® 6490 is a colourless, nearly odorless low-viscosity liquid. Dynasylan® 6490 is an excellent compatibiliser between inorganic fillers (e.g. kaolin, MDH, ATH) and organic polymers (e.g. EPDM, EVA, PE). The high boiling point of Dynasylan® 6490, together with its high flash point, gives it outstanding advantages with respect to safety and handling during processing. From an environmental viewpoint it should be noted that the amount of released hydrolysis methanol (VOC) is significantly reduced compared to monomeric vinyl silanes. voir moins | |
| Dynasylan® A | Evonik Operations GmbH, BL Silanes | Dynasylan® A is the ethyl ester of orthosilicic acid. In the literature it is frequently also referred to under the name TEOS (tetraethoxysilane). Dynasylan® A is a colourless, low-viscosity liquid with SiO2 content of 28.5%. Use requires acid- or alkali-...voir plus Dynasylan® A is the ethyl ester of orthosilicic acid. In the literature it is frequently also referred to under the name TEOS (tetraethoxysilane). Dynasylan® A is a colourless, low-viscosity liquid with SiO2 content of 28.5%. Use requires acid- or alkali-catalysed hydrolysis. Since all 4 ethoxy groups are able to participate in this reaction, Dynasylan® A is regarded as tetrafunctional. Hydrolysis leads to silanol groups which, in a subsequent condensation reaction, form very stable siloxane bonds (-Si-O-Si-). Condensation starts before hydrolysis is complete. During storage of these hydrolysates condensation, continues until a gel is formed. The rate of gelation depends on the concentration of water. voir moins | |
| DYNASYLAN® AMEO-T | Evonik Operations GmbH, BL Silanes | DYNASYLAN® AMEO-T is a blend of primary and secondary aminofunctional silanes. The dual nature of the product allows it to bind chemically to both inorganic materials and organic polymers, thus acting as an adhesion promoter, a surface modifier or as a re...voir plus DYNASYLAN® AMEO-T is a blend of primary and secondary aminofunctional silanes. The dual nature of the product allows it to bind chemically to both inorganic materials and organic polymers, thus acting as an adhesion promoter, a surface modifier or as a reactive reagent. voir moins | |
| Dynasylan® MEMO | Evonik Operations GmbH, BL Silanes | Dynasylan® MEMO is a methacrylfunctional silane that can be used as adhesion promoter, surface modifier, co-monomer for polymer synthesis and crosslinker. Dynasylan® MEMO is a clear, colorless liquid. It is soluble in alcohols, and aliphatic or aromatic h...voir plus Dynasylan® MEMO is a methacrylfunctional silane that can be used as adhesion promoter, surface modifier, co-monomer for polymer synthesis and crosslinker. Dynasylan® MEMO is a clear, colorless liquid. It is soluble in alcohols, and aliphatic or aromatic hydrocarbons. voir moins | |
| Dynasylan® P | Evonik Operations GmbH, BL Silanes | Dynasylan® P is mostly used as crosslinker for silicones. Dynasylan® P is a special silicic acid ester. It is mainly used as crosslinker in the silicone industry. Dynasylan® P can be further used as precursor for inorganic binders and as basic ingredient ...voir plus Dynasylan® P is mostly used as crosslinker for silicones. Dynasylan® P is a special silicic acid ester. It is mainly used as crosslinker in the silicone industry. Dynasylan® P can be further used as precursor for inorganic binders and as basic ingredient in sol-gel formulations. voir moins | |
| Dynasylan® SIVO 202 | Evonik Operations GmbH, BL Silanes | Dynasylan® SIVO 202 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 202 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silyla...voir plus Dynasylan® SIVO 202 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 202 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silylated polyurethanes, MS Polymers), RTV-silicones, two-part polyurethanes and two-part epoxies to inorganic surfaces and some difficult plastic surfaces. In addition, Dynasylan® SIVO 202 can lead to fast sealant curing and high-crosslinked products and it imparts both additional flexibility and hydrophobicity. voir moins | |
| Dynasylan® SIVO 203 | Evonik Operations GmbH, BL Silanes | Dynasylan® SIVO 203 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 203 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silyla...voir plus Dynasylan® SIVO 203 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 203 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silylated polyurethanes, MS Polymers), RTV-silicones, two-part polyurethanes and two-part epoxies to inorganic surfaces and some difficult plastic surfaces. In addition, Dynasylan® SIVO 203 can lead to fast sealant curing and high-crosslinked products and it imparts both additional flexibility and hydrophobicity. voir moins | |
| DYNASYLAN® SIVO 210 | Evonik Operations GmbH, BL Silanes | Dynasylan® SIVO 210 is an aminofunctional silane composition which acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers), as a surface modifier or ...voir plus Dynasylan® SIVO 210 is an aminofunctional silane composition which acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers), as a surface modifier or as chemical modification of substances. Dynasylan® SIVO 210 is a colorless to yellowish liquid with an amine-like odor which is soluble in alcohols, aliphatic or aromatic hydrocarbons. voir moins | |
| Dynasylan® VTEO | Evonik Operations GmbH, BL Silanes | Dynasylan® VTEO is comonly used as a monomer for solvent or water-borne acrylic polymers. It is usually used in small amounts to increase the crosslinking density and improve adhesion on substrates such as concrete and brick. | |
| Dynasylan® VTMO | Evonik Operations GmbH, BL Silanes | Dynasylan® VTMO is comonly used as a monomer for solvent or water-borne acrylic polymers. It is usually used in small amounts to increase the crosslinking density and improve adhesion on substrates such as concrete and brick. | |
| Dynasylan® VTMOEO | Evonik Operations GmbH, BL Silanes | Dynasylan® VTMOEO is a bifunctional organosilane possessing a reactive vinyl group and a hydrolyzable 2-methoxy-ethoxy-silyl group. The dual nature of its reactivity allows Dynasylan® VTMOEO to bind chemically to both inorganic materials (e.g. glass, meta...voir plus Dynasylan® VTMOEO is a bifunctional organosilane possessing a reactive vinyl group and a hydrolyzable 2-methoxy-ethoxy-silyl group. The dual nature of its reactivity allows Dynasylan® VTMOEO to bind chemically to both inorganic materials (e.g. glass, metals, fillers) and organic polymers (e.g. thermosets, thermoplastics, elastomers) thus functioning mainly as an efficient adhesion promoter and/or surface modifier. Dynasylan® VTMOEO is a colorless, low-viscosity liquid with a typical aromatic odor. voir moins | |
| Flytac 102-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...voir plus Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR. This product has a colour gardener (in 50% Toluene) of 4 max., an acid value of 20mg KOH/g max., and a softening point (R&B) of 97-100℃. voir moins | |
| FLYTAC 103-85 | Guangzhou Flying Dragon Chemical Ltd. | A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS,...voir plus A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. voir moins | |
| Flytac 103-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for thi...voir plus Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for this product include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It an also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. Flytac 103-E has a softening point (R&B) of 82-90°C min., an acid value of 3-8mg KOH/g max., and a colour gardener (in 50% Toluene) of 8 max. voir moins | |
| Flytac 104 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used...voir plus Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used as raw material for the manufacture of a number of products including bookbinding, caulking, paint and coatings, personal care and cosmetics, pressure sensitive adhesives, rubber and plastic modification, solvent-borne adhesives, tapes and labels, waterborne adhesives, and wax modification. This product has an abietic acid of 2.0% max., a softening point (R&B) of 76°C min., and a dehydroabietic acid of 8.0% max. voir moins |
