| CUMAR® 105 | Neville Chemical Company | CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne ...voir plus CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne and epoxy based coatings, IV ink modifiers, adhesives and sealants. voir moins | |
| Dynasylan® 1124 | Evonik Operations GmbH, BL Silanes | Dynasylan® 1124 is a secondary aminofunctional methoxy-silane. The product acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers). It can also be us...voir plus Dynasylan® 1124 is a secondary aminofunctional methoxy-silane. The product acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers). It can also be used for the chemical modification of polymers and isocyanates. voir moins | |
| DYNASYLAN® 1146 | Evonik Operations GmbH, BL Silanes | Hydrophobic Dynasylan® 1146 diaminofunctional silane is used in adhesives and sealants, and in coatings, to improve the adhesion of amino-reactive resins (e.g. RTV-silicones, two-part urethanes, silylated urethanes, MS polymers, and two-part epoxies) to i...voir plus Hydrophobic Dynasylan® 1146 diaminofunctional silane is used in adhesives and sealants, and in coatings, to improve the adhesion of amino-reactive resins (e.g. RTV-silicones, two-part urethanes, silylated urethanes, MS polymers, and two-part epoxies) to inorganic surfaces, plastic surfaces, and inorganic fillers. Dynasylan® 1146 silane is characterized by randomly distributed linear and cyclic oligosiloxanes and it fulfills the OECD polymer definition. Its low volatility and viscosity make compounding easy. Dynasylan® 1146 silane produces significantly less by-product (VOC) and has a correspondingly low odor level during application. voir moins | |
| Dynasylan® 40 | Evonik Operations GmbH, BL Silanes | Dynasylan® 40 is a ethyl silicate with a silicon dioxide content of approximately 40 - 42 % upon complete hydrolysis (the Si content of Dynasylan® 40 is calculated as SiO2). Dynasylan® 40 is formed in the presence of water from tetraethyl silicate (Si[OEt...voir plus Dynasylan® 40 is a ethyl silicate with a silicon dioxide content of approximately 40 - 42 % upon complete hydrolysis (the Si content of Dynasylan® 40 is calculated as SiO2). Dynasylan® 40 is formed in the presence of water from tetraethyl silicate (Si[OEt]4) by partial hydrolysis of the ethoxy groups to hydroxyl groups and subsequent condensation with formation of siloxane bonds (-Si-O-Si-). Dynasylan® 40 is a colorless, low-viscosity liquid with an SiO2 content of 40% (the Si content of Dynasylan® 40 is calculated as SiO2). The polysilicic acids still have a sufficient content of ethoxy groups which can be activated by acid- or base-catalyzed hydrolysis. Condensation starts even during hydrolysis, with the formation of relatively large polymeric molecules. During storage of these hydrolysates, condensation continues until a gel is formed, where the rate depends on the degree of hydrolysis. The action of the hydrolysates as binders is based on the continuation of the hydrolysis with subsequent gelation and dehydration to give polymeric SiO2 structures. voir moins | |
| Dynasylan® 4148 | Evonik Operations GmbH, BL Silanes | Dynasylan® 4148 is a ready-to-use silane, soluble in water and most organic solvents. Dynasylan® 4148 is a rheological additive which reduces the viscosity of highly-filled polymer systems, like aluminum trihydroxide-filled polyesters or SMC-pastes. Contr...voir plus Dynasylan® 4148 is a ready-to-use silane, soluble in water and most organic solvents. Dynasylan® 4148 is a rheological additive which reduces the viscosity of highly-filled polymer systems, like aluminum trihydroxide-filled polyesters or SMC-pastes. Contrary to most other organofunctional silanes, Dynasylan® 4148 features chemical polarity but has a non-reactive polar group. Furthermore, Dynasylan® 4148 can be used as anti-settling agent for fillers and pigments in paints as well as corrosion inhibitors in glycol based cooling agents. voir moins | |
| Dynasylan® 6490 | Evonik Operations GmbH, BL Silanes | Dynasylan® 6490 is a vinyl silane concentrate (oligomeric siloxane) containing vinyl and methoxy groups. Dynasylan® 6490 is a colourless, nearly odorless low-viscosity liquid. Dynasylan® 6490 is an excellent compatibiliser between inorganic fillers (e.g. ...voir plus Dynasylan® 6490 is a vinyl silane concentrate (oligomeric siloxane) containing vinyl and methoxy groups. Dynasylan® 6490 is a colourless, nearly odorless low-viscosity liquid. Dynasylan® 6490 is an excellent compatibiliser between inorganic fillers (e.g. kaolin, MDH, ATH) and organic polymers (e.g. EPDM, EVA, PE). The high boiling point of Dynasylan® 6490, together with its high flash point, gives it outstanding advantages with respect to safety and handling during processing. From an environmental viewpoint it should be noted that the amount of released hydrolysis methanol (VOC) is significantly reduced compared to monomeric vinyl silanes. voir moins | |
| Dynasylan® A | Evonik Operations GmbH, BL Silanes | Dynasylan® A is the ethyl ester of orthosilicic acid. In the literature it is frequently also referred to under the name TEOS (tetraethoxysilane). Dynasylan® A is a colourless, low-viscosity liquid with SiO2 content of 28.5%. Use requires acid- or alkali-...voir plus Dynasylan® A is the ethyl ester of orthosilicic acid. In the literature it is frequently also referred to under the name TEOS (tetraethoxysilane). Dynasylan® A is a colourless, low-viscosity liquid with SiO2 content of 28.5%. Use requires acid- or alkali-catalysed hydrolysis. Since all 4 ethoxy groups are able to participate in this reaction, Dynasylan® A is regarded as tetrafunctional. Hydrolysis leads to silanol groups which, in a subsequent condensation reaction, form very stable siloxane bonds (-Si-O-Si-). Condensation starts before hydrolysis is complete. During storage of these hydrolysates condensation, continues until a gel is formed. The rate of gelation depends on the concentration of water. voir moins | |
| DYNASYLAN® AMEO-T | Evonik Operations GmbH, BL Silanes | DYNASYLAN® AMEO-T is a blend of primary and secondary aminofunctional silanes. The dual nature of the product allows it to bind chemically to both inorganic materials and organic polymers, thus acting as an adhesion promoter, a surface modifier or as a re...voir plus DYNASYLAN® AMEO-T is a blend of primary and secondary aminofunctional silanes. The dual nature of the product allows it to bind chemically to both inorganic materials and organic polymers, thus acting as an adhesion promoter, a surface modifier or as a reactive reagent. voir moins | |
| Dynasylan® MEMO | Evonik Operations GmbH, BL Silanes | Dynasylan® MEMO is a methacrylfunctional silane that can be used as adhesion promoter, surface modifier, co-monomer for polymer synthesis and crosslinker. Dynasylan® MEMO is a clear, colorless liquid. It is soluble in alcohols, and aliphatic or aromatic h...voir plus Dynasylan® MEMO is a methacrylfunctional silane that can be used as adhesion promoter, surface modifier, co-monomer for polymer synthesis and crosslinker. Dynasylan® MEMO is a clear, colorless liquid. It is soluble in alcohols, and aliphatic or aromatic hydrocarbons. voir moins | |
| Dynasylan® P | Evonik Operations GmbH, BL Silanes | Dynasylan® P is mostly used as crosslinker for silicones. Dynasylan® P is a special silicic acid ester. It is mainly used as crosslinker in the silicone industry. Dynasylan® P can be further used as precursor for inorganic binders and as basic ingredient ...voir plus Dynasylan® P is mostly used as crosslinker for silicones. Dynasylan® P is a special silicic acid ester. It is mainly used as crosslinker in the silicone industry. Dynasylan® P can be further used as precursor for inorganic binders and as basic ingredient in sol-gel formulations. voir moins | |
| Dynasylan® SIVO 202 | Evonik Operations GmbH, BL Silanes | Dynasylan® SIVO 202 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 202 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silyla...voir plus Dynasylan® SIVO 202 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 202 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silylated polyurethanes, MS Polymers), RTV-silicones, two-part polyurethanes and two-part epoxies to inorganic surfaces and some difficult plastic surfaces. In addition, Dynasylan® SIVO 202 can lead to fast sealant curing and high-crosslinked products and it imparts both additional flexibility and hydrophobicity. voir moins | |
| Dynasylan® SIVO 203 | Evonik Operations GmbH, BL Silanes | Dynasylan® SIVO 203 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 203 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silyla...voir plus Dynasylan® SIVO 203 is a new multifunctional aminosilane adhesion promoter that can be used for a wide variety of applications. Dynasylan® SIVO 203 is mainly dedicated for use in adhesives & sealants to improve the adhesion of hybrid products (e.g. silylated polyurethanes, MS Polymers), RTV-silicones, two-part polyurethanes and two-part epoxies to inorganic surfaces and some difficult plastic surfaces. In addition, Dynasylan® SIVO 203 can lead to fast sealant curing and high-crosslinked products and it imparts both additional flexibility and hydrophobicity. voir moins | |
| DYNASYLAN® SIVO 210 | Evonik Operations GmbH, BL Silanes | Dynasylan® SIVO 210 is an aminofunctional silane composition which acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers), as a surface modifier or ...voir plus Dynasylan® SIVO 210 is an aminofunctional silane composition which acts as an adhesion promoter between inorganic materials (for example glass, metals and fillers) and organic polymers (thermosets, thermoplastics and elastomers), as a surface modifier or as chemical modification of substances. Dynasylan® SIVO 210 is a colorless to yellowish liquid with an amine-like odor which is soluble in alcohols, aliphatic or aromatic hydrocarbons. voir moins | |
| Dynasylan® VTEO | Evonik Operations GmbH, BL Silanes | Dynasylan® VTEO is comonly used as a monomer for solvent or water-borne acrylic polymers. It is usually used in small amounts to increase the crosslinking density and improve adhesion on substrates such as concrete and brick. | |
| Dynasylan® VTMO | Evonik Operations GmbH, BL Silanes | Dynasylan® VTMO is comonly used as a monomer for solvent or water-borne acrylic polymers. It is usually used in small amounts to increase the crosslinking density and improve adhesion on substrates such as concrete and brick. | |
| Dynasylan® VTMOEO | Evonik Operations GmbH, BL Silanes | Dynasylan® VTMOEO is a bifunctional organosilane possessing a reactive vinyl group and a hydrolyzable 2-methoxy-ethoxy-silyl group. The dual nature of its reactivity allows Dynasylan® VTMOEO to bind chemically to both inorganic materials (e.g. glass, meta...voir plus Dynasylan® VTMOEO is a bifunctional organosilane possessing a reactive vinyl group and a hydrolyzable 2-methoxy-ethoxy-silyl group. The dual nature of its reactivity allows Dynasylan® VTMOEO to bind chemically to both inorganic materials (e.g. glass, metals, fillers) and organic polymers (e.g. thermosets, thermoplastics, elastomers) thus functioning mainly as an efficient adhesion promoter and/or surface modifier. Dynasylan® VTMOEO is a colorless, low-viscosity liquid with a typical aromatic odor. voir moins | |
| Flytac 102-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...voir plus Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR. This product has a colour gardener (in 50% Toluene) of 4 max., an acid value of 20mg KOH/g max., and a softening point (R&B) of 97-100℃. voir moins | |
| FLYTAC 103-85 | Guangzhou Flying Dragon Chemical Ltd. | A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS,...voir plus A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. voir moins | |
| Flytac 103-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for thi...voir plus Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for this product include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It an also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. Flytac 103-E has a softening point (R&B) of 82-90°C min., an acid value of 3-8mg KOH/g max., and a colour gardener (in 50% Toluene) of 8 max. voir moins | |
| Flytac 104 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used...voir plus Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used as raw material for the manufacture of a number of products including bookbinding, caulking, paint and coatings, personal care and cosmetics, pressure sensitive adhesives, rubber and plastic modification, solvent-borne adhesives, tapes and labels, waterborne adhesives, and wax modification. This product has an abietic acid of 2.0% max., a softening point (R&B) of 76°C min., and a dehydroabietic acid of 8.0% max. voir moins | |
| Flytac 105-L | Guangzhou Flying Dragon Chemical Ltd. | Flytac105-L is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, waterborne adhesives, non-wovens, packaging, tapes and labels, as well as in wax depilatories. In...voir plus Flytac105-L is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, waterborne adhesives, non-wovens, packaging, tapes and labels, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-oxidizing, color-stable, highly tacky liquid resin. Flytac105-L has a softening point (R&B) of 85°C, an acid value of 9mg KOH/g max., and an ash content of 0.2% max. voir moins | |
| Flytac 106-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 106-100 is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesiv...voir plus Flytac 106-100 is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesive formulations, it contributes improved resistance to oxidation, greater heat stability, better retention of color, and greater retention of tack-imparting properties than ordinary rosin ester resins. Flytac 106-100 has a color gardener of 8~10, a specific gravity (25°C/25°C) of 1.060~1.090, and a softening point (R&B) of 95-102°C min. voir moins | |
| Flytac 106-100L | Guangzhou Flying Dragon Chemical Ltd. | Flytac 106-100L is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesi...voir plus Flytac 106-100L is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesive formulations, it contributes improved resistance to oxidation, greater heat stability, better retention of color, and greater retention of tack-imparting properties than ordinary rosin ester resins. This product has a color gardener of 4~6, a softening point (R&B) of 95-102°C, and a specific gravity (25°C/25°C) of 1.060~1.090. voir moins | |
| Flytac 107 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 107 is made of derivatives of gum rosin obtained by chemical treatment to reduce the Abietic Acid content. It is used as a tackifier for pressure sensitive adhesive, in the manufacture of SBR and other synthetic rubbers, as well as in important com...voir plus Flytac 107 is made of derivatives of gum rosin obtained by chemical treatment to reduce the Abietic Acid content. It is used as a tackifier for pressure sensitive adhesive, in the manufacture of SBR and other synthetic rubbers, as well as in important component for making potassium soaps. This product has a dehydrated acid content of 52.0% min., an unsaponifiable material of 10.0% max., and an abietic acid of 1% max. voir moins | |
| Flytac 111-101 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 111-101 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly st...voir plus Flytac 111-101 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly stabilized rosins commercially available, and is especially indicated as the tackifier in solvent adhesives and hot-melt applied coatings and adhesives that must excel in these properties. Flytac 111-101 has a tetrahydro resin acid of 10.0% min., an abietic acid of 2.0% max., and a dehydroabietic acid of 10.0% max. voir moins | |
| Flytac 111-301 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 111-301 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly st...voir plus Flytac 111-301 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly stabilized rosins commercially available, and is especially indicated as the tackifier in solvent adhesives and hot-melt applied coatings and adhesives that must excel in these properties. Flytac 111-301 has an abietic acid of 0-0.1% max., a softening point (R&B) of 78°C, and a tetrahydro resin acid level of 30.0-40.0%. voir moins | |
| Flytac 114-125 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-125 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...voir plus Flytac 114-125 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. This product offers color stability, is resistant to yellowing, and has good heat resistance and adhesion. Flytac 114-125 has a color (Gardner Grade) of 5 max., an acid value of 30mg KOH/g max., and a softening point (R&B) of 125 ± 2°C min. voir moins | |
| Flytac 114-130 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-130 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...voir plus Flytac 114-130 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. It offers color stability, resistant to yellowing, good heat resistance and adhesion. Flytac 114-130 has a softening point (R&B) of 130 ± 2°C min., an acid value of 30mg KOH/g max., and a color (Gardener Grade) of 5 max. voir moins | |
| Flytac 114-135 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-135 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...voir plus Flytac 114-135 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. It offers color stability, resistant to yellowing, good heat resistance and adhesion. Flytac 114-135 has an acid value of 30mg KOH/g max., a color (Gardner Grade) of 5 max., and a softening point (R&B) of 135 ± 2°C min. voir moins | |
| Flytac 115 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 115 is a specially designed highly stable 50% water-borne polymeric type tackifier dispersion with 23 degree (rolling & ball) softening point. It is a highly stabilized rosin ester dispersion designed to provide superior performance in adhesives pr...voir plus Flytac 115 is a specially designed highly stable 50% water-borne polymeric type tackifier dispersion with 23 degree (rolling & ball) softening point. It is a highly stabilized rosin ester dispersion designed to provide superior performance in adhesives properties, and is compatible with anionic & nonionic types of latexes. It adheres to a wide range of substrates. This product has a viscosity ((Brookifield 2#, 60rpm, 25°C,cps) PH(25°C)) of 150 max, a particle size (AVG) of 0.25μm, and a density (25°C) of 1.02g/ml. voir moins | |
| Flytac 116-110 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-110 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is deal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 190 ± 10mg K...voir plus Flytac 116-110 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is deal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 190 ± 10mg KOH/g, a softening point (R&B) of 110± 5°C, and a color gardner (50% Benzene solution) of 5 max. voir moins | |
| Flytac 116-130 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-130 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideally used for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 180...voir plus Flytac 116-130 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideally used for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 180 ± 10mg KOH/g, a softening point (R&B) of 130 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. voir moins | |
| Flytac 116-150 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-150 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 170 ± 10mg ...voir plus Flytac 116-150 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 170 ± 10mg KOH/g, a softening point (R&B) of 150 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. voir moins | |
| Flytac 116-160 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-160 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 200 ± 10mg ...voir plus Flytac 116-160 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 200 ± 10mg KOH/g, a softening point (R&B) of 160 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. voir moins | |
| Flytac 117-115 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-115 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-form...voir plus Flytac 117-115 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-115 has a softening point (R&B) of 110-120°C min., a dissoluble matter in hot water amount of 0.20, and an acid number of 145mg KOH/g min. voir moins | |
| Flytac 117-140 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-140 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-form...voir plus Flytac 117-140 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-140 has a softening point (R&B) of 135-145°C min., an acid number of 145mg KOH/g min., and a dissoluble matter in alcohol of 0.03% max. voir moins | |
| Flytac 117-95 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-95 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-formi...voir plus Flytac 117-95 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-95 has an acid number of 150mg KOH/g, a dissoluble matter in alcohol of 0.03% max., and a softening point (R&B) of 90-100°C min. voir moins | |
| FLYTAC 120-100W | Guangzhou Flying Dragon Chemical Ltd. | A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granu...voir plus A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granules, SBS and SIS base hot melt and pressure sensitive adhesives, EVA based hot melt adhesives for quality of packing, booking and cigarettes adhesives, hot melt paints and sealants and water or solvent bases adhesives. voir moins | |
| FLYTAC 120-90W | Guangzhou Flying Dragon Chemical Ltd. | A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granu...voir plus A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granules, SBS and SIS base hot melt and pressure sensitive adhesives, EVA based hot melt adhesives for quality of packing, booking and cigarettes adhesives, hot melt paints and sealants and water or solvent bases adhesives. voir moins | |
| Flytac 188-C5 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C5 is a kind of thermal plasticizing resin produced by C5, by-products of petroleum cracking, through pretreatment, polymerization and distillation. The major usages are tackifier for pressure sensitive adhesive, because of its well balance PSA...voir plus Flytac 188-C5 is a kind of thermal plasticizing resin produced by C5, by-products of petroleum cracking, through pretreatment, polymerization and distillation. The major usages are tackifier for pressure sensitive adhesive, because of its well balance PSA properties such as trackness, adhesive strength and cohesive strength. It can also be used in the production of paints, adhesives and in rubber industries. Flytac 188-C5 has an average molecular weight of 1000-2600, a melt viscosity (CPS at 200°C) of 300 max., and a softening point (R&B) of 95-105°C. voir moins | |
| Flytac 188-C5/C9 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C5/C9 is a copolymerization hydrocarbon petroleum resin, whose materials are C5 fraction and C9 fraction. It is a new product for the market, and has the good characters of C5 hydrocarbon resin and C9 hydrocarbon resin. It is an important raw m...voir plus Flytac 188-C5/C9 is a copolymerization hydrocarbon petroleum resin, whose materials are C5 fraction and C9 fraction. It is a new product for the market, and has the good characters of C5 hydrocarbon resin and C9 hydrocarbon resin. It is an important raw material for the product of paints, adhesives, and in rubber industries. Flytac 188-C5/C9 has an ash content of 0.1% max., an acid value of 0.3mg KOH/g max., and a softening point (B&R) of 90~120°C max. voir moins | |
| Flytac 188-C9 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C9 hydrocarbon petroleum resin is a kind of resin produced by C9 fraction, by products of petroleum cracking, through pretreatment,polymerization and distillation. It isn‘t a high polymer but a low polymer, with the molecular weight between 300...voir plus Flytac 188-C9 hydrocarbon petroleum resin is a kind of resin produced by C9 fraction, by products of petroleum cracking, through pretreatment,polymerization and distillation. It isn‘t a high polymer but a low polymer, with the molecular weight between 300-3000. It is an important raw material for the production of paints, adhesives and rubber industries. Flytac 188-C9 has a softening point (B&R) of 90-140°C, an acid value of 0.5mg KOH/g max., and an ash amount of 0.1% max. voir moins | |
| Flytac 188-HC5 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-HC5 hydrocarbon resin is a low molecular weight fully hydrogenated, water-white, inert, thermoplastic resin derived from petrochemical feedstocks. This resin is especially designed as tackifier in hot-melt adhesives requiring excellent color re...voir plus Flytac 188-HC5 hydrocarbon resin is a low molecular weight fully hydrogenated, water-white, inert, thermoplastic resin derived from petrochemical feedstocks. This resin is especially designed as tackifier in hot-melt adhesives requiring excellent color retention upon aging. It is an important raw material for the production of paints, adhesives and rubber industries. Flytac 188-HC5 has a softening point (B&R) of 95-105°Cg, an acid value of 0.5mg KOH/g max., and an ash amount of 0.02% max. voir moins | |
| Flytac102-100F | Guangzhou Flying Dragon Chemical Ltd. | Flytac102-100F is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...voir plus Flytac102-100F is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, Pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR.This product has a melt viscosity (CPS at 150°C) of 850-1300, a softening point (R&B) of 97-103°C, and a specific gravity (25°C/25°C) of 1.060~1.090. voir moins | |
| Flytac103-90 | Guangzhou Flying Dragon Chemical Ltd. | Flytac103-90 is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses...voir plus Flytac103-90 is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. This product has a colour gardener (in 50% Toleune) of 3 max., an acid value of 10mg KOH/g max., and a softening point (R&B) of 87-92°C min. voir moins | |
| Flytac105-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac105-E is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-ox...voir plus Flytac105-E is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-oxidizing, color-stable, highly tacky liquid resin. This product is ideally used for wax modification, waterborne adhesives, tapes and labels, solventborne adhesives, rubber and plastic modification, and paint and coatings. Flytac105-E has a softening point (R&B) of 78-88°C min., a specific gravity (25°C/25°C) of 1.060~1.090, and an ash content of 0.1% max. voir moins | |
| KTR-100 | Suparna Chemicals Ltd. | KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-100 has a softening point of 95 to 105 °C, in butyl acetate of 75 to 95 at 25 °C (cps), and a hydroxyl value of 170 to 200. voir moins | |
| KTR-118 | Suparna Chemicals Ltd. | KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-118 has a softening point of 105 to 115 °C, in butyl acetate of 100 to 120 at 25 °C (cps), and a hydroxyl value of 180 to 210. voir moins | |
| KTR-123 | Suparna Chemicals Ltd. | KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-123 has a softening point of 105 to 115 °C, in butyl acetate of 110 to 140 at 25 °C (cps), and a hydroxyl value of 200 to 230. voir moins | |
| LX®-1035 Resin | Neville Chemical Company | LX®-1035 Resin is a flaked resin that improves cohesive strength and promotes heat resistance of adhesives. In addition it can contribute to rapid solvent release and faster drying of litho inks. It has applications in the adhesives and sealants industry ...voir plus LX®-1035 Resin is a flaked resin that improves cohesive strength and promotes heat resistance of adhesives. In addition it can contribute to rapid solvent release and faster drying of litho inks. It has applications in the adhesives and sealants industry as well as in certain coatings related to the automobile industry. voir moins | |
| LX®-1200 | Neville Chemical Company | LX®-1200 is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, improves tack and bond strength in adhesives and enhances leafing and brilliance in metallic paints and inks. It is applied to mastics, constructi...voir plus LX®-1200 is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, improves tack and bond strength in adhesives and enhances leafing and brilliance in metallic paints and inks. It is applied to mastics, construction and flooring adhesives, high solids solvent-borne alkyd based coatings, litho printing inks and aluminum paint. voir moins | |
| LX®-1200, 130 | Neville Chemical Company | LX®-1200, 130 is an inert thermoplastic hydrocarbon resin flake. This product is applied to mastics, construction and flooring adhesives, high solids solvent-borne alkyd based coatings, litho printing inks, metallic litho printing inks and aluminum paint. | |
| LX®-2161 Resin | Neville Chemical Company | LX®-2161 Resin is an inert thermoplastic hydrocarbon resin of amber flakes that enhances the wetting of pigments and fillers, improves tack and bond strength in adhesives and are soluble in aliphatic solvents and vegetable oils. They can be applied to lit...voir plus LX®-2161 Resin is an inert thermoplastic hydrocarbon resin of amber flakes that enhances the wetting of pigments and fillers, improves tack and bond strength in adhesives and are soluble in aliphatic solvents and vegetable oils. They can be applied to litho printing inks and high solids solvent-borne alkyd based coatings in addition to mastics, construction and flooring adhesives. voir moins | |
| LX®-238 Resin | Neville Chemical Company | LX®-238 Resin is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, is soluble in aromatic and aliphatic solvents/oils and has applications for use in high solids solvent-borne alkyd based coatings and concret...voir plus LX®-238 Resin is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, is soluble in aromatic and aliphatic solvents/oils and has applications for use in high solids solvent-borne alkyd based coatings and concrete cure compounds. voir moins | |
| NEVCHEM® 100 | Neville Chemical Company | NEVCHEM® 100 is a thermoplastic hydrocarbon resin that improves track and bond strength in adhesive and caulks, promote wetting of pigments and fillers, provide leafing characteristics for metallic pigments and enable good thermal stability. They are use...voir plus NEVCHEM® 100 is a thermoplastic hydrocarbon resin that improves track and bond strength in adhesive and caulks, promote wetting of pigments and fillers, provide leafing characteristics for metallic pigments and enable good thermal stability. They are used in hot melt and construction adhesives, sealants and caulks, high solids solvent-borne and alkyd based coatings and litho printing inks. voir moins | |
| NEVCHEM® 110 | Neville Chemical Company | NEVCHEM® 110 is a thermoplastic hydrocarbon resin that promotes tack and bond strength in adhesive and caulks, enhances wetting and pigments of fillers, provide leafing characteristics for metallic pigments and give thermal stability. They are applied to ...voir plus NEVCHEM® 110 is a thermoplastic hydrocarbon resin that promotes tack and bond strength in adhesive and caulks, enhances wetting and pigments of fillers, provide leafing characteristics for metallic pigments and give thermal stability. They are applied to hot melt and construction adhesives, sealants and caulks, high solids solvent-borne and alkyd based coatings and be used in asphalt modification. voir moins | |
| NEVCHEM® 120 | Neville Chemical Company | NEVCHEM® 120 is a thermoplastic hydrocarbon resin derived from petroleum mixed from aromatic/aliphatic feedstreams. This product promotes tack and bond strength in adhesive and caulks, enhances wetting of pigments and fillers, provides leafing characteris...voir plus NEVCHEM® 120 is a thermoplastic hydrocarbon resin derived from petroleum mixed from aromatic/aliphatic feedstreams. This product promotes tack and bond strength in adhesive and caulks, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments and offers thermal stability. They can be applied to hot melt and construction adhesives, sealants and caulks, high solids solvent-borne and alkyd based coatings, litho printing inks and asphalt modification. voir moins | |
| NEVCHEM® 130 | Neville Chemical Company | NEVCHEM® 130 is a thermoplastic hydrocarbon resin. This product contains compatibility and tackifier for EVA, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments and offers thermal stability. They can be applie...voir plus NEVCHEM® 130 is a thermoplastic hydrocarbon resin. This product contains compatibility and tackifier for EVA, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments and offers thermal stability. They can be applied to hot melt and construction adhesives, sealants and caulks, high solids solvent-borne and alkyd based coatings, UV ink modification and asphalt modification. voir moins | |
| NEVCHEM® 140 | Neville Chemical Company | NEVCHEM® 140 is a thermoplastic hydrocarbon resin produced from petroleum mixed from aromatic/aliphatic feedstreams. This product can be applied to construction adhesives, sealants, high solids solvent-borne and alkyd based coatings, litho printing inks a...voir plus NEVCHEM® 140 is a thermoplastic hydrocarbon resin produced from petroleum mixed from aromatic/aliphatic feedstreams. This product can be applied to construction adhesives, sealants, high solids solvent-borne and alkyd based coatings, litho printing inks and asphalt modification. voir moins | |
| NEVCHEM® 150 | Neville Chemical Company | NEVCHEM® 150 is a thermoplastic hydrocarbon resin derived from petroleum mixed from aromatic/aliphatic feedstreams. This product is compatible with medium and long oil alkyds, improves acid and moisture resistance and contains thermal stability. It has ap...voir plus NEVCHEM® 150 is a thermoplastic hydrocarbon resin derived from petroleum mixed from aromatic/aliphatic feedstreams. This product is compatible with medium and long oil alkyds, improves acid and moisture resistance and contains thermal stability. It has applications to sealants and construction adhesives. voir moins | |
| NEVCHEM® 200 | Neville Chemical Company | NEVCHEM® 200 is a thermoplastic C9 hydrocarbon resin that has excellent compatibility and tackifier for EVA, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments and offers thermal stability. It is applied to ho...voir plus NEVCHEM® 200 is a thermoplastic C9 hydrocarbon resin that has excellent compatibility and tackifier for EVA, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments and offers thermal stability. It is applied to hot melt and construction adhesives, sealants, high solids solvent-borne and epoxy based coatings, UV ink modification and concrete cure. voir moins | |
| NEVCHEM® 220 | Neville Chemical Company | NEVCHEM® 220 is a thermoplastic C9 hydrocarbon resin that has excellent compatibility with a range of polymers and elastomers, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments, and improves gloss. It is appl...voir plus NEVCHEM® 220 is a thermoplastic C9 hydrocarbon resin that has excellent compatibility with a range of polymers and elastomers, enhances wetting of pigments and fillers, provides leafing characteristics for metallic pigments, and improves gloss. It is applied to hot melt, solvent based and construction adhesives, sealants, high solids solvent-borne and epoxy based coatings and used in asphalt modification. voir moins | |
| NEVCHEM® 240 | Neville Chemical Company | NEVCHEM® 240 is a thermoplastic C9 hydrocarbon resin compatible with a range of polymers and elastomers that provides leafing characteristics for metallic pigments as well as improves gloss and increases cohesive strength in SBC based adhesives. This prod...voir plus NEVCHEM® 240 is a thermoplastic C9 hydrocarbon resin compatible with a range of polymers and elastomers that provides leafing characteristics for metallic pigments as well as improves gloss and increases cohesive strength in SBC based adhesives. This product is applied to solvent based and construction adhesives, sealants, high solids solvent-borne and alkyd based coatings and is used in asphalt modification. voir moins | |
| NEVCHEM® 250 | Neville Chemical Company | NEVCHEM® 250 is a thermoplastic C9 hydrocarbon resin that is compatible with a range of polymers and elastomers, enhances the wetting of pigments and fillers, improves gloss and increases cohesive strength in SBC based adhesives. This product is applied t...voir plus NEVCHEM® 250 is a thermoplastic C9 hydrocarbon resin that is compatible with a range of polymers and elastomers, enhances the wetting of pigments and fillers, improves gloss and increases cohesive strength in SBC based adhesives. This product is applied to solvent based and construction adhesives, sealants, high solids solvent-borne and alkyd based coatings and used in asphalt modification. voir moins | |
| NEVEX® 1069 | Neville Chemical Company | NEVEX® 1069 is a pure monomer modified C9 aromatic hydrocarbon resin that has compatibility with EVA copolymers, promotes stress and strain properties for EVA systems, enhances wetting of pigments and fillers, improves moisture resistance and contains hea...voir plus NEVEX® 1069 is a pure monomer modified C9 aromatic hydrocarbon resin that has compatibility with EVA copolymers, promotes stress and strain properties for EVA systems, enhances wetting of pigments and fillers, improves moisture resistance and contains heat stability. It has applications in hot melt adhesives, as a modifier for epoxy and alkyd based coatings, in construction and high solid solvent based adhesives and in asphalt modification. voir moins | |
| NEVPENE® 9545 | Neville Chemical Company | NEVPENE® 9545 resin is a unique low molecular weight petroleum hydrocarbon resin. This amber liquid is compatible with most elastomers, has thermal stability and enhances water resistance. It can be applied to adhesives and sealants, construction adhesive...voir plus NEVPENE® 9545 resin is a unique low molecular weight petroleum hydrocarbon resin. This amber liquid is compatible with most elastomers, has thermal stability and enhances water resistance. It can be applied to adhesives and sealants, construction adhesives, high solids solvent borne coatings and in asphalt modification. voir moins | |
| NEVTAC® 10 | Neville Chemical Company | NEVTAC® 10 is a liquid pale amber colored resin that is compatible with aliphatic polymers and waxes. It has applications in pressure sensitive and hot melt adhesives and roofing and butyl elastomer tackifiers. | |
| Polymer ST 48 | Evonik Operations GmbH, BL Silanes | Polymer ST 48 offers a good handling viscosity and is therefore easy to apply manually. Formulation surfaces are quickly tack-free after application, which ensures rapid processing and avoids long waiting times. It is especially recommended for the applic...voir plus Polymer ST 48 offers a good handling viscosity and is therefore easy to apply manually. Formulation surfaces are quickly tack-free after application, which ensures rapid processing and avoids long waiting times. It is especially recommended for the application as sealant for interior or exterior joints, e.g. expansion or connection joints, interior joints for dry walling, joints at staircases. voir moins | |
| Polymer ST 61 | Evonik Operations GmbH, BL Silanes | Polymer ST 61 is a high quality polymer which is used for wood floor adhesive formulations. Polymer ST 61 allows a high degree of flexibility for the formulations: adhesives with high strength and hardness are possible as well as soft adhesives with high ...voir plus Polymer ST 61 is a high quality polymer which is used for wood floor adhesive formulations. Polymer ST 61 allows a high degree of flexibility for the formulations: adhesives with high strength and hardness are possible as well as soft adhesives with high elasticity. voir moins | |
| Polymer ST 61 LV | Evonik Operations GmbH, BL Silanes | Polymer ST 61 LV is a plasticizer-free product which addresses the same formulation properties as Polymer ST 61. Its viscosity is approx. 70 % less, thus it allows quicker dosing, lower formulation viscosities and higher possible filler loading levels. | |
| Polymer ST 77 | Evonik Operations GmbH, BL Silanes | Polymer ST 77 is free of phthalates and is highly recommended for demanding applications where a balanced stress-strain behavior is required as in transport and assembly applications. Examples for the use of Polymer ST 77-based formulations are the assemb...voir plus Polymer ST 77 is free of phthalates and is highly recommended for demanding applications where a balanced stress-strain behavior is required as in transport and assembly applications. Examples for the use of Polymer ST 77-based formulations are the assembly of superstructural parts, bumpers, etc. Mechanical fastening is often avoided as it could cause damage to the materials used. In addition, it could negatively affect the design. voir moins | |
| Polymer ST 80 | Evonik Operations GmbH, BL Silanes | Polymer ST 80 is a high quality binder for adhesive formulations where high bonding strength and high surface hardness after curing are required. | |
| Polymer ST 81 | Evonik Operations GmbH, BL Silanes | Polymer ST 81 does not contain plasticizers, it offers a large variability in formulation design. It allows the formulation of both tin- and phthalate-free products. It allows formulators to enter markets such as wood construction, transport and automotiv...voir plus Polymer ST 81 does not contain plasticizers, it offers a large variability in formulation design. It allows the formulation of both tin- and phthalate-free products. It allows formulators to enter markets such as wood construction, transport and automotive, assembly as well as light-weight construction. voir moins | |
| TEGOPAC® Bond 150 | Evonik Operations GmbH, BL Silanes | TEGOPAC® Bond 150 is recommended for usage as a binder in assembly adhesives and sealant formulations. The combination of outstanding through-cure and excellent elastic recovery properties allows formulations with TEGOPAC® Bond 150 to be used in a number ...voir plus TEGOPAC® Bond 150 is recommended for usage as a binder in assembly adhesives and sealant formulations. The combination of outstanding through-cure and excellent elastic recovery properties allows formulations with TEGOPAC® Bond 150 to be used in a number of demanding applications, e.g. in construction of sandwich elements, for flexible bonding in transport applications or for high quality expansion joints. voir moins | |
| TEGOPAC® Bond 160 | Evonik Operations GmbH, BL Silanes | TEGOPAC® Bond 160 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 160 shows excellent through cure properties,...voir plus TEGOPAC® Bond 160 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 160 shows excellent through cure properties, improved water & thermal resistance and excellent elastic recovery properties. The low polymer viscosity allows quick & easy handling. voir moins | |
| TEGOPAC® Bond 170 | Evonik Operations GmbH, BL Silanes | TEGOPAC® Bond 170 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 170 shows excellent through cure properties,...voir plus TEGOPAC® Bond 170 is a silylated polymer that is used for production of neutral curing adhesives and sealants. The polymer is based on a unique polymer technology with lateral crosslinking groups. TEGOPAC® Bond 170 shows excellent through cure properties, improved water & thermal resistance and excellent elastic recovery properties. The low polymer viscosity allows quick & easy handling. voir moins | |
| TEGOPAC® Bond 251 | Evonik Operations GmbH, BL Silanes | TEGOPAC® Bond 251 is a hybrid polymer with a modified backbone that contains hydrophilic segments. Formulations with TEGOPAC® Bond 251 are suitable to replace flexible PUR adhesives and sealants. | |
| TEGOPAC® RD 1 | Evonik Operations GmbH, BL Silanes | TEGOPAC® RD 1 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers,...voir plus TEGOPAC® RD 1 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers, and other additives is possible to address applications like parquet adhesives, roof sealing applications or pressure sensitive adhesives. voir moins | |
| TEGOPAC® RD 2 | Evonik Operations GmbH, BL Silanes | TEGOPAC® RD 2 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers,...voir plus TEGOPAC® RD 2 is a silane-modified polymers which can be used to reduce viscosities of adhesives & sealant formulations. It can be blended with different types of silane-modified polymers and epoxy polymers. Formulating with various plasticizers, fillers, and other additives is possible to address applications like parquet adhesives, roof sealing applications or pressure sensitive adhesives. voir moins | |
| TEGOPAC® Seal 100 | Evonik Operations GmbH, BL Silanes | TEGOPAC® Seal 100 is a moisture curing silane-modified polymer recommended for low modulus sealant formulations which are used in construction applications (e.g. for façades, expansion joints, etc. ) or for indoor applications. TEGOPAC® Seal 100 is also ...voir plus TEGOPAC® Seal 100 is a moisture curing silane-modified polymer recommended for low modulus sealant formulations which are used in construction applications (e.g. for façades, expansion joints, etc. ) or for indoor applications. TEGOPAC® Seal 100 is also recommended for use in sealant and adhesive formulations where vibration and sound dampening is an issue. voir moins | |
| VPS SIVO 260 | Evonik Operations GmbH, BL Silanes | VPS SIVO 260 is an organofunctional silane oligomer. Acts as an adhesion promoter. Leads to adequate adhesive cure and imparts additional flexibility and hydrophobicity. Soluble in alcohols, aliphatic and aromatic hydrocarbons, but it can undergo reaction...voir plus VPS SIVO 260 is an organofunctional silane oligomer. Acts as an adhesion promoter. Leads to adequate adhesive cure and imparts additional flexibility and hydrophobicity. Soluble in alcohols, aliphatic and aromatic hydrocarbons, but it can undergo reactions with ketones or ester solvents. Helps eliminate the need for special primers in numerous bonding applications. Exhibits excellent wetting on substrates and forms weather- and moisture-resistant bonds to substrates which are partially difficult to adhere, well balanced mechanical properties and significant VOC-reduction compared to conventional amino silanes. Suitable for use in adhesive and sealants, silane modified polyurethane/ polyether, RTV-1/RTV-2 silicones, butyl rubber and improved adhesion especially to polycarbonate. Recommended dosage for VPS SIVO 260 is 0-5-2.0 wt. %. It has a shelf life of 9 months. voir moins | |
| VPS SIVO 280 | Evonik Operations GmbH, BL Silanes | VPS SIVO 280 is an organofunctional silane oligomer. Acts as an adhesion promoter. Leads to adequate adhesive cure and imparts additional flexibility and hydrophobicity. Soluble in alcohols, aliphatic and aromatic hydrocarbons, but it can undergo reaction...voir plus VPS SIVO 280 is an organofunctional silane oligomer. Acts as an adhesion promoter. Leads to adequate adhesive cure and imparts additional flexibility and hydrophobicity. Soluble in alcohols, aliphatic and aromatic hydrocarbons, but it can undergo reactions with ketones or ester solvents. Helps eliminate the need for special primers in numerous bonding applications. Exhibits excellent wetting on substrates and forms weather- and moisture-resistant bonds to substrates which are partially difficult to adhere, well balanced mechanical properties and significant VOC-reduction compared to conventional amino silanes. Suitable for use in adhesive and sealants, silane modified polyurethane/ polyether, RTV-1/RTV-2 silicones, butyl rubber and improved adhesion especially to PMMA. Recommended dosage for VPS SIVO 260 is 0-5-2.0 wt. %. It has a shelf life of 9 months. voir moins | |
| Automated Discharge Systems | Charles Ross & Son Company | A Ross Discharge System can eliminate wasted hours scraping heavy or sticky materials from a mix vessel. With push-button simplicity, the system can automatically discharge a 1000-gallon batch in minutes — into bulk containers, filling or packaging equipm...voir plus A Ross Discharge System can eliminate wasted hours scraping heavy or sticky materials from a mix vessel. With push-button simplicity, the system can automatically discharge a 1000-gallon batch in minutes — into bulk containers, filling or packaging equipment, an extruder, or a two or three-roll mill. voir moins |  |
| Double Planetary Mixer | Charles Ross & Son Company | Ross pioneered the Double Planetary Mixer design more than 60 years ago. Design updates make this mixer suitable for use in applications up to 7,000,000 centipoise. A high speed design variation is also available. |  |
| High Shear Mixer | Charles Ross & Son Company | All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear...voir plus All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear particles and droplets, and expel material at high velocity into the surrounding mix, creating intense hydraulic shear. voir moins |  |
| High Speed Disperser | Charles Ross & Son Company | Ross High Speed Dispersers are the industry standard for durability, faster dispersion and low maintenance costs. Standard models include: explosion-proof, inverter duty motors; heavy duty V-belt drives and bearings; safety switches; an air/oil hydraulic ...voir plus Ross High Speed Dispersers are the industry standard for durability, faster dispersion and low maintenance costs. Standard models include: explosion-proof, inverter duty motors; heavy duty V-belt drives and bearings; safety switches; an air/oil hydraulic lift system with hand/foot controls; and stainless steel wetted parts and shaft guard. Sizes range from 1/2 HP to 200 HP to handle batches from 1 to 2000 gallons. Custom designs are also available. voir moins |  |
| Multi-Shaft Mixer | Charles Ross & Son Company | We offer Dual and Triple Shaft designs to meet your specific process requirements. Our economical Dual Shaft design includes a conventional high speed disperser and a two wing anchor agitator. This configuration is ideal for straight forward dispersion an...voir plus We offer Dual and Triple Shaft designs to meet your specific process requirements. Our economical Dual Shaft design includes a conventional high speed disperser and a two wing anchor agitator. This configuration is ideal for straight forward dispersion and mixing applications. voir moins |  |
| Planetary Dispersers | Charles Ross & Son Company | The patented Planetary Disperser combines a planetary blade and a high speed dispersion blade. The planetary and the high speed disperser blades rotate on their own axes and also rotate continuously around the vessel. The planetary blade feeds materials ...voir plus The patented Planetary Disperser combines a planetary blade and a high speed dispersion blade. The planetary and the high speed disperser blades rotate on their own axes and also rotate continuously around the vessel. The planetary blade feeds materials directly into the high shear zone of the orbiting high speed disperser. This combination of unique mixing actions eliminate the need for multiple mixers i.e. 2 technologies in one machine. voir moins |  |
| Powder Induction | Charles Ross & Son Company | All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear...voir plus All rotor/stator mixers are comprised of a rotor that turns at high speed within a stationary stator. In a “single-stage” unit, the rotor includes a single set of four blades. As the rotating blades pass each opening in the stator, they mechanically shear particles and droplets, and expel material at high velocity into the surrounding mix, creating intense hydraulic shear. voir moins |  |
| PreMax | Charles Ross & Son Company | This single-stage rotor/stator generator is specially contoured to generate both high shear and vigorous flow in a batch mixing environment. Designed especially for pigment dispersions, the Delta rotor/stator generator is used in the Ross PreMax* to produ...voir plus This single-stage rotor/stator generator is specially contoured to generate both high shear and vigorous flow in a batch mixing environment. Designed especially for pigment dispersions, the Delta rotor/stator generator is used in the Ross PreMax* to produce an intense combination of mechanical, hydraulic and cavitational shear, which results in aggressive deagglomeration. voir moins |  |
| Ribbon Blender | Charles Ross & Son Company | Ribbon Blenders are ideal for powder blending applications. The dual action ribbon agitator creates an intimate blend in a short cycle time. Ross stocks Ribbon Blenders in many sizes from 1 - 100 cu.ft. working capacity. |  |
| Sanitary Mixers | Charles Ross & Son Company | Ross serves the requirements of the Food, Cosmetic and Pharmaceutical industries, in virtually every industrialized country around the world. We have the experience and production capacity that no other manufacturer of specialty mixing and blending equipm...voir plus Ross serves the requirements of the Food, Cosmetic and Pharmaceutical industries, in virtually every industrialized country around the world. We have the experience and production capacity that no other manufacturer of specialty mixing and blending equipment can match. voir moins |  |
| Static/Motionless Mixers | Charles Ross & Son Company | Ross LPD/LLPD (low pressure drop) and ISG (interfacial surface generator) Motionless Mixers are well known for their wide ranging uses in turbulent and laminar flow mixing applications. |  |
| Systems And Controls | Charles Ross & Son Company | Ross Systems and Controls (SysCon) is a leading worldwide supplier of control systems. We offer packages that range from simple on/off switches to sophisticated PLC based recipe systems. Each system, standard or custom, is designed to meet your specific n...voir plus Ross Systems and Controls (SysCon) is a leading worldwide supplier of control systems. We offer packages that range from simple on/off switches to sophisticated PLC based recipe systems. Each system, standard or custom, is designed to meet your specific needs. voir moins |  |
| Three Roll Mill | Charles Ross & Son Company | When Ross produced the first Three Roll Mill more than 80 years ago, we revolutionized pigment dispersion — with superior consistency and finer dispersion than ever before. Today the original Ross Three Roll Mills are still the standard by which all other...voir plus When Ross produced the first Three Roll Mill more than 80 years ago, we revolutionized pigment dispersion — with superior consistency and finer dispersion than ever before. Today the original Ross Three Roll Mills are still the standard by which all others are measured — in applications as diverse as magnetic coatings, cosmetics, paints, inks and high performance ceramics. voir moins |  |
| Tumble Blenders | Charles Ross & Son Company | Ross Tumble Blenders are supplied with generous standard features, including double cone design in 316 stainless steel construction, manually operated Butterfly valve for discharge - 24” discharge clearance Hinged stainless steel charging opening, mirror ...voir plus Ross Tumble Blenders are supplied with generous standard features, including double cone design in 316 stainless steel construction, manually operated Butterfly valve for discharge - 24” discharge clearance Hinged stainless steel charging opening, mirror finish on interior surfaces, 150 grit finish on exterior surfaces, and the non-stainless steel components are finished with a durable two-component paint. voir moins |  |
| Vertical Blender | Charles Ross & Son Company | Ross Vertical Blenders provide an excellent design alternative for applications when your product is shear sensitive or your process parameters are critical Products that require low-impact blending are best handled in a Ross Vertical Blender. The blendin...voir plus Ross Vertical Blenders provide an excellent design alternative for applications when your product is shear sensitive or your process parameters are critical Products that require low-impact blending are best handled in a Ross Vertical Blender. The blending action of the slow-turning blending screw is far more gentle than the agitators in a Ribbon Blender of the same working volume. voir moins |  |
