Commercial: Active

Africa & Middle East, Asia Pacific, Europe, Latin America, North America

Also Available In, Density / Specific Gravity, Density, Density, Apparent (Bulk) Density, Melt Mass-Flow Rate (MFR), Melt Mass-Flow Rate (MFR), Melt Volume-Flow Rate (MVR), Melt Volume-Flow Rate (MVR), Spiral Flow, Mold Shrink, Linear-Flow, Mold Shrink, Linear-Trans, Molding Shrinkage, Water Absorption @ 24 hrs, Water Absorption 24h/23C, Water Absorption @ Sat., Water Absorption Sat/23C, Water Absorption @ Equil, Water Absorption 23C/50RH, Viscosity Number, Tensile Modulus, Tensile Modulus, Tensile Strength, Tensile Strength at Yield, Tensile Stress at Yield, Tensile Strength at Break, Tensile Stress at Break, Tensile Stress, Tensile Elongation at Yield, Tensile Strain at Yield, Tensile Elongation at Break, Tensile Strain at Break, Nominal Tensile Strain at Break, Tensile Creep Modulus 1h, Tensile Creep Modulus 1000h, Flexural Modulus, Flexural Modulus, Flexural Strength, Flexural Stress, Flexural Strength at Yield, Flexural Strength at Break, Compressive Strength, Compressive Stress, Coefficient of Friction, Taber Abrasion Resistance, Wear Factor, Film Thickness - Tested, Charpy Notched Impact Strength, Charpy Unnotched Impact Strength, Notched Izod Impact, Notched Izod Impact (Area), Notched Izod Impact Strength, Unnotched Izod Impact, Unnotched Izod Impact Strength, Instrumented Dart Impact, Multi-Axial Instrumented Impact Energy, Multi-Axial Instrumented Impact Peak Force, Gardner Impact, Gardner Impact, Tensile Impact Strength, Rockwell Hardness, Rockwell Hardness, Shore Hardness, Ball Indentation Hardness, DTUL (66 psi) - Unannealed, DTUL (0.45 MPa) Unannealed, DTUL (66 psi) - Annealed, DTUL (0.45 MPa) Annealed, DTUL (264 psi) - Unannealed, DTUL (1.80 MPa) Unannealed, DTUL (264 psi) - Annealed, DTUL (1.80 MPa) Annealed, Continuous Use Temperature, Glass Transition Temperature, Glass Transition Temperature, Vicat Softening Temperature, Vicat Softening Temperature, Ball Indentation Temperature, Melting Temperature, CLTE, Flow, CLTE, Flow (TMA), Coefficient of Linear Thermal Expansion, Flow, CLTE, Transverse, CLTE, Transverse (TMA), Coefficient of Linear Thermal Expansion, Transverse, Specific Heat, Thermal Conductivity, Thermal Conductivity, RTI Elec, RTI Imp, RTI Str, Surface Resistivity, Surface Resistivity, Volume Resistivity, Volume Resistivity, Volume Resistivity, Dielectric Strength, Electric Strength, Dielectric Constant, Dielectric Constant, Relative Permittivity, Dissipation Factor, Dissipation Factor, Dissipation Factor, Arc Resistance, Comparative Tracking Index, High Amp Arc Ignition (HAI), Hot-wire Ignition (HWI), Burning Rate, Glow Wire Flammability Index, Glow Wire Ignition Temperature, Oxygen Index, Oxygen Index, Gloss, Refractive Index, Refractive Index, Light Transmittance, Haze, Melt Density, Melt Thermal Conductivity, Drying Temperature, Drying Time, Drying Time, Maximum, Dew Point, Suggested Max Moisture, Suggested Shot Size, Suggested Max Regrind, Hopper Temperature, Rear Temperature, Middle Temperature, Front Temperature, Nozzle Temperature, Processing (Melt) Temp, Melt Temperature (Optimum), Mold Temperature, Injection Pressure, Holding Pressure, Back Pressure, Screw Speed, Clamp Tonnage, Vent Depth, Injection Notes, Drying Temperature, Drying Time, Cylinder Zone 1 Temp., Cylinder Zone 2 Temp., Cylinder Zone 3 Temp., Cylinder Zone 4 Temp., Adapter Temperature, Melt Temperature, Die Temperature, Extrusion Notes