| 1,4-Butanediol (1,4-BDO) | DCC (Dairen Chemical Corp.) | 1,4-Butanediol (1,4-BDO) is produced by hydro-formulation and hydrogenation of Allyl Alcohol, carbon monoxide and hydrogen. 1,4-Butanediol is a colorless, high-boiling liquid with a low order of toxicity. 1,4-Butanediol is used as a raw material for manuf...展开 1,4-Butanediol (1,4-BDO) is produced by hydro-formulation and hydrogenation of Allyl Alcohol, carbon monoxide and hydrogen. 1,4-Butanediol is a colorless, high-boiling liquid with a low order of toxicity. 1,4-Butanediol is used as a raw material for manufacturing carrier solvent in printing ink, and is a key component of hot melt adhesive. 收起 | |
| Alkoxylated 2-Methyl-1,3-Propanediol | DCC (Dairen Chemical Corp.) | Alkoxylated 2-Methyl-1,3-Propanediol is produced by Alkoxylation of 2-Methyl-1,3-Propanediol and Alkoxide. It is a colorless liquid with two primary hydroxyls. Alkoxylated 2-Methyl-1,3-Propanediol is used as a raw material in printing inks, adhesives, and...展开 Alkoxylated 2-Methyl-1,3-Propanediol is produced by Alkoxylation of 2-Methyl-1,3-Propanediol and Alkoxide. It is a colorless liquid with two primary hydroxyls. Alkoxylated 2-Methyl-1,3-Propanediol is used as a raw material in printing inks, adhesives, and paints. 收起 | |
| CF1-141 | NuSil Silicone Technology 1 | CF1-141 is a high technology silicone primer that is specially formulated to be used with platinum-cured systems and is colored red to provide an easy visual determination of surface coverage. It is a lower Volatile Organic Component (VOC) product and air...展开 CF1-141 is a high technology silicone primer that is specially formulated to be used with platinum-cured systems and is colored red to provide an easy visual determination of surface coverage. It is a lower Volatile Organic Component (VOC) product and air dries. This primer improves adhesion of addition-cured systems to various substrates such as glass, metals, plastics, ceramics and other silicone materials. 收起 | |
| CF1-3800 | NuSil Silicone Technology 1 | CF1-3800 is a thermally conductive, fluorosilicone elastomer that cures at room temperature, or rapidly with the addition of heat. It can be used to adhere covers on housings, modules, and other configurations that require a non-flowable material. This pr...展开 CF1-3800 is a thermally conductive, fluorosilicone elastomer that cures at room temperature, or rapidly with the addition of heat. It can be used to adhere covers on housings, modules, and other configurations that require a non-flowable material. This product can also be utilized as an adhesive, sealant or molding material when solvent resistance is needed. It can provide the transfer of heat between electrical components and heat sinks, and can operate at a temperature range of -65°C to 225°C (-85°F to 437°F). 收起 | |
| CF2-135 | NuSil Silicone Technology 1 | CF2-135 is a silicone primer that is specifically designed to be used with platinum-cured systems where conventional primers will not be sufficient. This product will help to improve the adhesion of addition-cured systems to various substrates such as woo...展开 CF2-135 is a silicone primer that is specifically designed to be used with platinum-cured systems where conventional primers will not be sufficient. This product will help to improve the adhesion of addition-cured systems to various substrates such as wood, metals, ceramics, plastics, and other silicone materials. For the best bonding results, be sure that the surface being primed is clean and degreased. 收起 | |
| CF5-3521-2 | NuSil Silicone Technology 1 | CF5-3521-2 is a two part, 50 mole % fluorosilicone that has a 1:1 Mix Ratio (Part A:B). It can be cured at room temperature, or more rapidly by heating it in an oven or with a heating lamp. The product is especially useful as a coating, sealant, adhesive ...展开 CF5-3521-2 is a two part, 50 mole % fluorosilicone that has a 1:1 Mix Ratio (Part A:B). It can be cured at room temperature, or more rapidly by heating it in an oven or with a heating lamp. The product is especially useful as a coating, sealant, adhesive or molding material in applications that require solvent resistance. 收起 | |
| CF6-135 | NuSil Silicone Technology 1 | CF6-135 is a one-component, high technology silicone primer that is translucent to preserve visibility with translucent products. It is specially designed to be used with platinum cured systems where conventional primers are insufficient. This product wil...展开 CF6-135 is a one-component, high technology silicone primer that is translucent to preserve visibility with translucent products. It is specially designed to be used with platinum cured systems where conventional primers are insufficient. This product will improve the adhesion of addition-cured systems to many different substrates such as glass, metals, plastics, ceramics and other silicone material. 收起 | |
| CV-1161 | NuSil Silicone Technology 1 | CV-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid and particulate contaminants. It can be used in applications that require low outgassing and minimal volatile condesable materials. This ...展开 CV-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid and particulate contaminants. It can be used in applications that require low outgassing and minimal volatile condesable materials. This product is ideal for adhering and bonding silicone elastomers, metals, paper, glass, fabric organics rubbers, some synthetics, and films such as polyester or kapton. 收起 | |
| CV-1500 | NuSil Silicone Technology 1 | CV-1500 is a one part, black, electrically conductive RTV silicone adhesive/sealant that can be used for RFI and EMI shielding in electrical and space applications that require static dissipation. It can also protect components from extremes in temperatur...展开 CV-1500 is a one part, black, electrically conductive RTV silicone adhesive/sealant that can be used for RFI and EMI shielding in electrical and space applications that require static dissipation. It can also protect components from extremes in temperature, humidity, radiation, thermal and mechanical stress. This adhesive is well suited for form-in-place conductive gaskets and attaching heating coils to solar collector plates. 收起 | |
| CV-2500 | NuSil Silicone Technology 1 | CV-2500 is a strong silicone based adhesive that is made to handle extreme conditions in space applications including condensation, humidity, radiation, and both mechanical and thermal stress. It can also be an adhesive in applications that involve solar ...展开 CV-2500 is a strong silicone based adhesive that is made to handle extreme conditions in space applications including condensation, humidity, radiation, and both mechanical and thermal stress. It can also be an adhesive in applications that involve solar cell arrays where clarity and low volatility is needed. 收起 | |
| CV-2566 | NuSil Silicone Technology 1 | CV-2566 is a flowable silicone adhesive that has a broad operating temperature range. The primary use for this product is to be used for applications that require low outgassing and helps eliminate condensation in sensitive devices. In space and electroni...展开 CV-2566 is a flowable silicone adhesive that has a broad operating temperature range. The primary use for this product is to be used for applications that require low outgassing and helps eliminate condensation in sensitive devices. In space and electronic applications, it can be utilized as a sealant or adhesive to help control high vacuum environments. 收起 | |
| CV-2567 | NuSil Silicone Technology 1 | CV-2567 is a pourable RTV siicone that can be used as a diluent for reducing the viscosity of other controlled volatility silicones. This product meets the ASTM 595 low outgas specifications outlined in NASA and the European Space Agency. It can be used a...展开 CV-2567 is a pourable RTV siicone that can be used as a diluent for reducing the viscosity of other controlled volatility silicones. This product meets the ASTM 595 low outgas specifications outlined in NASA and the European Space Agency. It can be used as an adhesive or sealant for electronic and space applications. 收起 | |
| CV-2568 | NuSil Silicone Technology 1 | CV-2568 is a thixotropic RTV silicone that has a low density and has controlled volatility. This product act as a bonding or sealant in space applications. It has a broad operating temperature range and can provide radiation resistance, oxidation and ther...展开 CV-2568 is a thixotropic RTV silicone that has a low density and has controlled volatility. This product act as a bonding or sealant in space applications. It has a broad operating temperature range and can provide radiation resistance, oxidation and thermal stability. It can also be utilized in applications that require low outgassing under extreme operating conditions. 收起 | |
| CV-2900 | NuSil Silicone Technology 1 | CV-2900 is a non-corrosive silicone adhesive that is designed for enhanced performance in extreme low and high temperatures. It can be used as a bond and sealant for applications such as overhead or vertical joints that require a non-slumping and one-part...展开 CV-2900 is a non-corrosive silicone adhesive that is designed for enhanced performance in extreme low and high temperatures. It can be used as a bond and sealant for applications such as overhead or vertical joints that require a non-slumping and one-part material. It can also be utilized as an adhesive , caulking or potting material in electronics/space applications that require minimal outgassing and provides protection from condensation in sensitive devices. 收起 | |
| CV-2943 | NuSil Silicone Technology 1 | CV-2943 is a thermally conductive RTV silicone that has controlled volatility and is designed for enhanced performance in extreme high or low temperatures. It can be used for applications that require low outgassing and minimal volatile condensables under...展开 CV-2943 is a thermally conductive RTV silicone that has controlled volatility and is designed for enhanced performance in extreme high or low temperatures. It can be used for applications that require low outgassing and minimal volatile condensables under extreme operating conditions. This product is also utilized as an adhesive for openings in housings or modules where grooves and other configurations require a limited flow material. 收起 | |
| CV2-1142 | NuSil Silicone Technology 1 | CV2-1142 is a non-corrosive, non-slumping, translucent RTV silicone adhesive/sealant that has controlled volatility. It can be used in applications that require low outgassing under extreme operating conditions. This product is useful for sealing and bond...展开 CV2-1142 is a non-corrosive, non-slumping, translucent RTV silicone adhesive/sealant that has controlled volatility. It can be used in applications that require low outgassing under extreme operating conditions. This product is useful for sealing and bonding in applications such as overhead or vertical joints that require a non-slumping, one-part material. It can also be utilized as a sealant, caulking, adhesive or potting material in space and electrical applications that require minimal outgassing. 收起 | |
| CV2-1161 | NuSil Silicone Technology 1 | CV2-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid particulate contaminants. It is able to withstand normal pressure variations as well as high temperature exposure. This product is ideal...展开 CV2-1161 is a pressure sensitive silicone adhesive that retains its adhesive qualities in the presence of minor liquid particulate contaminants. It is able to withstand normal pressure variations as well as high temperature exposure. This product is ideal for bonding and adhering silicone elastomers, paper, metals, glass, fabric, films, and some synthetics. It can also be used for applications that require low outgassing and minimal volatile condensable materials. 收起 | |
| CV3-2500 | NuSil Silicone Technology 1 | CV3-2500 is an optically clear silicone that is has controlled volatility. It is an ideal product for applications that require a low viscosity to create a superior flow and low outgassing. This is how it helps keep condensation from affecting sensitive d...展开 CV3-2500 is an optically clear silicone that is has controlled volatility. It is an ideal product for applications that require a low viscosity to create a superior flow and low outgassing. This is how it helps keep condensation from affecting sensitive devices. It can also be utilized as an adhesive for projects involving solar arrays. 收起 | |
| CV4-1161-5 | NuSil Silicone Technology 1 | CV4-1161-5 is a one-part, double-sided pressure sensitive adhesive tape that is best used to adhere and bond metals, paper, glass, fabric, organic rubbers, synthetics and films. It has the ability to collect dust in and around sensitive electronic compone...展开 CV4-1161-5 is a one-part, double-sided pressure sensitive adhesive tape that is best used to adhere and bond metals, paper, glass, fabric, organic rubbers, synthetics and films. It has the ability to collect dust in and around sensitive electronic components and is designed to withstand extreme temperature/pressure variations. 收起 | |
| CV4-2289-1 | NuSil Silicone Technology 1 | CV4-2289-1 is a thixotropic silicone elastomer that can be used as an adhesive that offers superior tear strength. This silicone also demonstrates flexibility at extremely low temperatures with a stiffening temperature of approximately -115°C. It can be u...展开 CV4-2289-1 is a thixotropic silicone elastomer that can be used as an adhesive that offers superior tear strength. This silicone also demonstrates flexibility at extremely low temperatures with a stiffening temperature of approximately -115°C. It can be used to protect electronic components, cable harness breakouts, seals, and gaskets from harsh environmental conditions. 收起 | |
| CV7-1142-1 | NuSil Silicone Technology 1 | CV7-1142-1 is a non corrosive material that has a white color and it is a non-slumping silicone RTV. It can be used as a caulking, adhesive or sealant that protects sensitive circuits, connectors and switches in space applications. This product has a broa...展开 CV7-1142-1 is a non corrosive material that has a white color and it is a non-slumping silicone RTV. It can be used as a caulking, adhesive or sealant that protects sensitive circuits, connectors and switches in space applications. This product has a broad operating temperature range so it can withstand hot and cold conditions. It also can be used for sealing openings in modules or housings where grooves or other configurations require a non-flowable to limited flow material. 收起 | |
| DA-100 | DCC (Dairen Chemical Corp.) | DA-100 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-100 forms a flexible film with adhesive properties for broad applications. DA-100 is used as a base emu...展开 DA-100 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-100 forms a flexible film with adhesive properties for broad applications. DA-100 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-100 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-100L | DCC (Dairen Chemical Corp.) | DA-100L is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-100L forms a flexible film with adhesive properties for broad applications. DA-100L is used as a base e...展开 DA-100L is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-100L forms a flexible film with adhesive properties for broad applications. DA-100L is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-100L is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-101 | DCC (Dairen Chemical Corp.) | DA-101 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-101 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C o...展开 DA-101 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-101 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 1500-2500 mPa.s. DA-101 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-101 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-102 | DCC (Dairen Chemical Corp.) | DA-102 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-102 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C o...展开 DA-102 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-102 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 2500-3700 mPa.s. DA-102 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-102 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-102H | DCC (Dairen Chemical Corp.) | DA-102H is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-102H forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C...展开 DA-102H is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-102H forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 3500-4500 mPa.s. DA-102H is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-102H is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-103 | DCC (Dairen Chemical Corp.) | DA-103 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-103 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C o...展开 DA-103 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-103 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 1500-2500 mPa.s. DA-103 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-103 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-103H | DCC (Dairen Chemical Corp.) | DA-103H is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-103H forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C...展开 DA-103H is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-103H forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 3200-4200 mPa.s. DA-103H is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-103H is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-104 | DCC (Dairen Chemical Corp.) | DA-104 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-104 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C o...展开 DA-104 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-104 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 2000-3000 mPa.s. DA-104 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-104 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-107 | DCC (Dairen Chemical Corp.) | DA-107 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-107 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C o...展开 DA-107 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-107 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 1000-2500 mPa.s. DA-107 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-107 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-1100 | DCC (Dairen Chemical Corp.) | DA-1100 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and it forms a stable emulsion. DA-1100 improves adhesion, flex strength, abrasion resistance, and workability of modified compounds. DA-1100 ca...展开 DA-1100 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and it forms a stable emulsion. DA-1100 improves adhesion, flex strength, abrasion resistance, and workability of modified compounds. DA-1100 can be used in tile adhesives. 收起 | |
| DA-111 | DCC (Dairen Chemical Corp.) | DA-111 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-111 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C o...展开 DA-111 is a non-plasticized, aqueous, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-111 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 1500-2500 mPa.s. It is designed as a medium Tg product at around approximately 14 °C. DA-111 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-111 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-1120 | DCC (Dairen Chemical Corp.) | DA-1120 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and it forms a stable emulsion. DA-1120 improves adhesion, flex strength, abrasion resistance, and workability of modified compounds. DA-1120 ca...展开 DA-1120 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and it forms a stable emulsion. DA-1120 improves adhesion, flex strength, abrasion resistance, and workability of modified compounds. DA-1120 can be used in tile adhesives. 收起 | |
| DA-1122 | DCC (Dairen Chemical Corp.) | DA-1122 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and it forms a stable emulsion. DA-1122 improves adhesion, flex strength, abrasion resistance, and workability of modified compounds. DA-1122 ca...展开 DA-1122 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and it forms a stable emulsion. DA-1122 improves adhesion, flex strength, abrasion resistance, and workability of modified compounds. DA-1122 can be used in tile adhesives. 收起 | |
| DA-1126 | DCC (Dairen Chemical Corp.) | DA-1126 is a water re-dispersible powder based on a vinyl acetate/ethylene copolymer based containing polyvinyl alcohol as a protective colloid. DA-1126 improves adhesion, flexibility, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1126 is a water re-dispersible powder based on a vinyl acetate/ethylene copolymer based containing polyvinyl alcohol as a protective colloid. DA-1126 improves adhesion, flexibility, plasticity, abrasion resistance and workability of modified compounds. It is used in ceramic tile adhesives, and EIFS. 收起 | |
| DA-1130 | DCC (Dairen Chemical Corp.) | DA-1130 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1130 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1130 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1130 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. It can be used in tile adhesives. 收起 | |
| DA-1133 | DCC (Dairen Chemical Corp.) | DA-1133 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1133 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1133 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1133 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1133 is used in construction adhesives. 收起 | |
| DA-117 | DCC (Dairen Chemical Corp.) | DA-117 is a non-plasticized, aqueous, milky, white dispersion of a vinyl acetate-ethylene copolymer with high solid contents developed to provide a versatile base for construction applications. After evaporation of its water content, DA-117 forms a flexib...展开 DA-117 is a non-plasticized, aqueous, milky, white dispersion of a vinyl acetate-ethylene copolymer with high solid contents developed to provide a versatile base for construction applications. After evaporation of its water content, DA-117 forms a flexible film with adhesive properties for broad applications. It has a viscosity at 25 °C of 500-1500 mPa.s. DA-117 is used in joint compounds and decorative coatings, and carpet back coatings. 收起 | |
| DA-1200 | DCC (Dairen Chemical Corp.) | DA-1200 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1200 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1200 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1200 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1200 is used in tile adhesives. 收起 | |
| DA-1210 | DCC (Dairen Chemical Corp.) | DA-1210 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1210 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1210 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1210 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1210 is used in construction adhesives, sealing slurries, and repair mortars. 收起 | |
| DA-125 | DCC (Dairen Chemical Corp.) | DA-125 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -8 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-125 is used as general adhesive f...展开 DA-125 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -8 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-125 is used as general adhesive for packaging, bookbinding, and bonding for plastic films, coated papers. DA-125 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-125 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-128 | DCC (Dairen Chemical Corp.) | DA-128 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13°C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128 is used as general adhesive f...展开 DA-128 is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13°C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128 is used as general adhesive for packaging, bookbinding, and bonding for plastic films, coated papers. DA-128 is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-128 is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-128H | DCC (Dairen Chemical Corp.) | DA-128H is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128H is used as general adhesiv...展开 DA-128H is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. Due to its low Tg at around -13 °C, the dry film remains flexible even at temperatures below 0 °C. In general, DA-128H is used as general adhesive for packaging, bookbinding, and bonding for plastic films, coated papers. DA-128H is used as a base emulsion for the formulation of adhesives for difficult substrates, such as lacquered surfaces, foils, and plastic films in the packaging and paper industry. DA-128H is also a base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-1400 | DCC (Dairen Chemical Corp.) | DA-1400 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1400 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1400 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1400 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1400 is used in tile adhesives, and sealing slurries. 收起 | |
| DA-1410 | DCC (Dairen Chemical Corp.) | DA-1410 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1410 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds....展开 DA-1410 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1410 improves adhesion, flexural strength, plasticity, abrasion resistance and workability of modified compounds. DA-1410 is used in construction adhesives. 收起 | |
| DA-1420 | DCC (Dairen Chemical Corp.) | DA-1420 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1420 improves adhesion, flexural strength, plasticity, abrasion resistance, and workability of modified compound...展开 DA-1420 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1420 improves adhesion, flexural strength, plasticity, abrasion resistance, and workability of modified compounds. DA-1420 is used in tile adhesives. 收起 | |
| DA-1430 | DCC (Dairen Chemical Corp.) | DA-1430 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1430 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. D...展开 DA-1430 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1430 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. DA-1430 is used in tile adhesives, and trowelling compounds. 收起 | |
| DA-1450 | DCC (Dairen Chemical Corp.) | DA-1450 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1450 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. D...展开 DA-1450 is a water re-dispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. DA-1450 improves adhesion, flex strength, plasticity, abrasion resistance, and workability of modified compounds. DA-1450 is used in tile adhesives, and construction adhesives. 收起 | |
| DA-180L | DCC (Dairen Chemical Corp.) | DA-180L is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. After the evaporation of its water content, DA-180L dries to a clear, soft and flexible film to provide a better waterproofing property. DA-180L ...展开 DA-180L is a non-plasticized, aqueous, milky, white copolymer dispersion based on vinyl acetate and ethylene. After the evaporation of its water content, DA-180L dries to a clear, soft and flexible film to provide a better waterproofing property. DA-180L is used in general adhesives. 收起 | |
| DA-265 | DCC (Dairen Chemical Corp.) | DA-265 is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene-acrylate terpolymer emulsion with a solid content of 65%. After drying, a water-resistant, clear and flexible film is formed, exhibiting stability against degradation, discoloration...展开 DA-265 is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene-acrylate terpolymer emulsion with a solid content of 65%. After drying, a water-resistant, clear and flexible film is formed, exhibiting stability against degradation, discoloration by UV-light, oxygen and the ozone. DA-265 is used in mineral coatings, and floor, wall, or ceiling adhesives. . 收起 | |
| DA-265H | DCC (Dairen Chemical Corp.) | DA-265H is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene-acrylate terpolymer emulsion with a solid content of 65%. A water-resistant, clear and flexible film is formed after drying. This film exhibits stability against degradation, disco...展开 DA-265H is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene-acrylate terpolymer emulsion with a solid content of 65%. A water-resistant, clear and flexible film is formed after drying. This film exhibits stability against degradation, discoloration, oxygen, and the ozone. Because of DA-265H's adjusted ethylene content, this film is extremely tacky and uses no plasticizers to get softness or flexibility. DA-265H is used in mineral coatings, and floor, wall, or ceiling adhesives. 收起 | |
| DA-310 | DCC (Dairen Chemical Corp.) | DA-310 is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene copolymer emulsion containing incorporated carboxylic groups. It exhibits VAE emulsion properties together with increased adhesion to metals, like aluminum. DA-310 is used for seali...展开 DA-310 is a non-plasticized, aqueous, milky, white vinyl acetate-ethylene copolymer emulsion containing incorporated carboxylic groups. It exhibits VAE emulsion properties together with increased adhesion to metals, like aluminum. DA-310 is used for sealing plastics or metals to other substrates, and as a raw material for adhesives. 收起 | |
| DA-3510 | DCC (Dairen Chemical Corp.) | DA-3510 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. This resin is soft and flexible, because of its relatively high ethylene content. DA-3510 enhances the adhesion, fle...展开 DA-3510 is a water-redispersible vinyl acetate/ethylene copolymer powder that is readily dispersible in water and forms a stable emulsion. This resin is soft and flexible, because of its relatively high ethylene content. DA-3510 enhances the adhesion, flexural strength, plasticity, and workability of modified compounds. DA-3510 is recommended for use as a sole binder for making construction adhesives and seals. 收起 | |
| DA-6200 | DCC (Dairen Chemical Corp.) | DA-6200 is a water re-dispersible powder based on vinyl acetate/ethylene copolymer containing polyvinyl alcohol as a protective colloid. DA-6200 contains a fine mineral filler as an anti-blocking agent. It is free of solvents, plasticizers and film-formin...展开 DA-6200 is a water re-dispersible powder based on vinyl acetate/ethylene copolymer containing polyvinyl alcohol as a protective colloid. DA-6200 contains a fine mineral filler as an anti-blocking agent. It is free of solvents, plasticizers and film-forming agents. DA-6200 is recommended for blending with inorganic binders such as cement, hydrated lime to modify mortar hydration systems, tile adhesives, EIFS, and finishing plasters. 收起 | |
| DA-652 | DCC (Dairen Chemical Corp.) | DA-652 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, the extra viscous DA-652 forms a flexible film with adhesive properties for a broad range of applications....展开 DA-652 is an aqueous, non-plasticized, milky white copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, the extra viscous DA-652 forms a flexible film with adhesive properties for a broad range of applications. It has a viscosity at 25 °C of 15000-25000 mPa.s. DA-652 is used as base emulsion for floor, wall, or ceiling adhesives. 收起 | |
| DA-691 | DCC (Dairen Chemical Corp.) | DA-691 is a non-plasticized, aqueous, milky white, cross-linkable copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-691 forms a flexible and soft film. It has a viscosity at 25 °C of 100-500 mPa.s. DA-691...展开 DA-691 is a non-plasticized, aqueous, milky white, cross-linkable copolymer dispersion based on vinyl acetate and ethylene. After evaporation of its water content, DA-691 forms a flexible and soft film. It has a viscosity at 25 °C of 100-500 mPa.s. DA-691's main use is in EPI wood glue. 收起 | |
| DA-901 | DCC (Dairen Chemical Corp.) | DA-901 is a non-plasticized, aqueous, milky white terpolymer dispersion based on vinyl chloride, vinyl acetate and ethylene. Due to it's low Tg levels it provides a soft transparent film. It is generally used as an adhesive and provides a fire retardant p...展开 DA-901 is a non-plasticized, aqueous, milky white terpolymer dispersion based on vinyl chloride, vinyl acetate and ethylene. Due to it's low Tg levels it provides a soft transparent film. It is generally used as an adhesive and provides a fire retardant property. DA-901 is used as a general adhesive and is specially suitable for wood applications. 收起 | |
| DA-908 | DCC (Dairen Chemical Corp.) | DA-908 is an aqueous, milky white terpolymer dispersion based on vinyl chloride, vinyl acetate and ethylene. DA-908 leads to a clear film with low surface tack, and resistance to water, alkali, solvents, light, and aging. It has a Tg value of 20-30 °C and...展开 DA-908 is an aqueous, milky white terpolymer dispersion based on vinyl chloride, vinyl acetate and ethylene. DA-908 leads to a clear film with low surface tack, and resistance to water, alkali, solvents, light, and aging. It has a Tg value of 20-30 °C and is a cloudy substance initially. DA-908 is used as a base emulsion for general adhesives and EPI wood adhesives. 收起 | |
| DA-910 | DCC (Dairen Chemical Corp.) | DA-910 is a copolymer of Ethylene and Vinyl Chloride with amide functionality. It has fire retardant, water, and alkali resistance properties. It has a Tg rating of between -2 and 2 °C. DA-910 can be used as a base sealant emulsion in non-woven fabrics an...展开 DA-910 is a copolymer of Ethylene and Vinyl Chloride with amide functionality. It has fire retardant, water, and alkali resistance properties. It has a Tg rating of between -2 and 2 °C. DA-910 can be used as a base sealant emulsion in non-woven fabrics and paper binder, paper and fabric impregnation binder, flocking binder, car sheet and carpet back coating, and adhesive for high frequency curing. 收起 | |
| DA-920 | DCC (Dairen Chemical Corp.) | DA-920 is a copolymer of Ethylene and Vinyl Chloride with amide functionality. It has fire retardant, water, and alkali resistance properties. It has a Tg rating of between 18 and 22 °C. DA-920 can be used as a base sealant emulsion in non-woven fabrics a...展开 DA-920 is a copolymer of Ethylene and Vinyl Chloride with amide functionality. It has fire retardant, water, and alkali resistance properties. It has a Tg rating of between 18 and 22 °C. DA-920 can be used as a base sealant emulsion in non-woven fabrics and paper binder, paper and fabric impregnation binder, flocking binder, car sheet and carpet back coating, and adhesive for high frequency curing. 收起 | |
| DA-930 | DCC (Dairen Chemical Corp.) | DA-930 is a copolymer of Ethylene and Vinyl Chloride with amide functionality. It has fire retardant, water, and alkali resistance properties. It has a Tg rating of between 28 and 32 °C. DA-930 can be used as a base sealant emulsion in non-woven fabrics a...展开 DA-930 is a copolymer of Ethylene and Vinyl Chloride with amide functionality. It has fire retardant, water, and alkali resistance properties. It has a Tg rating of between 28 and 32 °C. DA-930 can be used as a base sealant emulsion in non-woven fabrics and paper binder, paper and fabric impregnation binder, flocking binder, car sheet and carpet back coating, and adhesive for high frequency curing. 收起 | |
| EPM-2420 | NuSil Silicone Technology 1 | EPM-2420 is a general purpose silicone adhesive that has a low volatility and a 1:1 Mix Ratio (Part A: Part B). The primary function of this adhesive is to protect electric components and assemblies against vibration, shock, dust, moisture, chemicals and ...展开 EPM-2420 is a general purpose silicone adhesive that has a low volatility and a 1:1 Mix Ratio (Part A: Part B). The primary function of this adhesive is to protect electric components and assemblies against vibration, shock, dust, moisture, chemicals and other hazards. It is also ideal for applications where a low viscosity and clarity are important. 收起 | |
| EPM-2890 | NuSil Silicone Technology 1 | EPM-2890 is a one part, white, silicone adhesive that is thermally conductive and non corrosive. It has the ability to operate on a wide temperature range and provide moderate heat transfer between electrical components and their heat sinks. This product ...展开 EPM-2890 is a one part, white, silicone adhesive that is thermally conductive and non corrosive. It has the ability to operate on a wide temperature range and provide moderate heat transfer between electrical components and their heat sinks. This product can also function as a caulking, sealing, potting or adhesive material in electronics applications that require minimal outgassing to prevent condensation from building in sensitive devices. 收起 | |
| FS-3730-2 | NuSil Silicone Technology 1 | FS-3730-2 is a black adhesive/sealant that is based on a fluorosilicone polymer with 100 mole % fluorosilicone. It can be utilized to bond or protect hardware components that are exposed to aviation fuels or gasoline. This product can also be used for sea...展开 FS-3730-2 is a black adhesive/sealant that is based on a fluorosilicone polymer with 100 mole % fluorosilicone. It can be utilized to bond or protect hardware components that are exposed to aviation fuels or gasoline. This product can also be used for sealing or bonding applications requiring fuel and/or solvent resistance. Another strong property is that it bonds aggressively to most surfaces. 收起 | |
| FS1-3730 | NuSil Silicone Technology 1 | FS1-3730 is an adhesive/sealant that is translucent and based on a 100 mole % fluorosilicone polymer. This product can be utilized for sealing and bonding applications that require solvent and/or fuel resistance. It is a very strong product and will bond ...展开 FS1-3730 is an adhesive/sealant that is translucent and based on a 100 mole % fluorosilicone polymer. This product can be utilized for sealing and bonding applications that require solvent and/or fuel resistance. It is a very strong product and will bond aggressively to most surfaces. 收起 | |
| FS3-3730 | NuSil Silicone Technology 1 | FS3-3730 is a translucent, one-part, adhesive/sealant that has 100 mole % flouorosilicone. It is strong and will bond aggressively to most surfaces. This product can be utilized for bonding and sealing applications that require solven and/or fuel resistan...展开 FS3-3730 is a translucent, one-part, adhesive/sealant that has 100 mole % flouorosilicone. It is strong and will bond aggressively to most surfaces. This product can be utilized for bonding and sealing applications that require solven and/or fuel resistance. It can also be used for protecting or bonding hardware components that have been exposed to gasoline or aviation fuels. 收起 | |
| n-Propanol | DCC (Dairen Chemical Corp.) | n-Propanol is a by-product which is produced by hydro-formulation and hydrogenation of Allyl Alcohol, carbon monoxide, and hydrogen. It is a medium boiling point, colorless liquid and has a typical alcohol odor, and is soluble in water, alcohol, and ether...展开 n-Propanol is a by-product which is produced by hydro-formulation and hydrogenation of Allyl Alcohol, carbon monoxide, and hydrogen. It is a medium boiling point, colorless liquid and has a typical alcohol odor, and is soluble in water, alcohol, and ether. n-Propanol is used in solvents, as an intermediate chemical for synthesis, industrial coatings, adhesives, and printing inks. 收起 | |
| Picassian® AC-111 | Stahl Polymers | Picassian® AC-111 is an aqueous emulsion of an anionic acrylic copolymer that is used in leather finishes. It makes films clear, gloss, soft, and tack free. This product is flexible, elastic, has good chemical resistance properties, good scrub resistance ...展开 Picassian® AC-111 is an aqueous emulsion of an anionic acrylic copolymer that is used in leather finishes. It makes films clear, gloss, soft, and tack free. This product is flexible, elastic, has good chemical resistance properties, good scrub resistance properties, and low water absorption properties. 收起 | |
| Picassian® AC-213 | Stahl Polymers | Picassian® AC-213 is a waterbased anionic pure acrylic copolymer emulsion agent that is used in adhesives, textile coatings, and industrial shoe polish. It has good adhesion properties, good water resistance properties, good humidity resistance properties...展开 Picassian® AC-213 is a waterbased anionic pure acrylic copolymer emulsion agent that is used in adhesives, textile coatings, and industrial shoe polish. It has good adhesion properties, good water resistance properties, good humidity resistance properties, and improves scrub resistance properties. 收起 | |
| Picassian® AC-222 | Stahl Polymers | Picassian® AC-222 is a waterbased anionic alkali soluable acrylic copolymer emulsion agent. It is used in many wood and board coatings, basecoats, grinding binders, pigment sealers, flexo inks, gravure inks, leather finishes, and hobby adhesives. This pro...展开 Picassian® AC-222 is a waterbased anionic alkali soluable acrylic copolymer emulsion agent. It is used in many wood and board coatings, basecoats, grinding binders, pigment sealers, flexo inks, gravure inks, leather finishes, and hobby adhesives. This product has good pigment wetting attributes, high pigment loading capacity attributes, is quick to sand, and is quick to dry. 收起 | |
| Picassian® AC-246 | Stahl Polymers | Picassian® AC-246 is a waterbased, anionic, acrylic copolymer emulsion agent. It is used in inks, overprints, coated paper, metalized substrates, and glossy wood varnishes. This product has good holdout properties, good water resistance properties, good g...展开 Picassian® AC-246 is a waterbased, anionic, acrylic copolymer emulsion agent. It is used in inks, overprints, coated paper, metalized substrates, and glossy wood varnishes. This product has good holdout properties, good water resistance properties, good grease resistance properties, good alcohol compatibility, and good pigment compatibility. 收起 | |
| Picassian® AC-295 | Stahl Polymers | Picassian® AC-295 is a waterbased anionic styrene acrylic copolymer emulsion agent. It is used in anticorrosive coatings, concrete flooring, and with UV coatings as a way of reducing cost. This product has good adhesive properties with metallic and plasti...展开 Picassian® AC-295 is a waterbased anionic styrene acrylic copolymer emulsion agent. It is used in anticorrosive coatings, concrete flooring, and with UV coatings as a way of reducing cost. This product has good adhesive properties with metallic and plastic substrates, is widely compatible with many types of binders, has good clarity properties, has good gloss properties, has good chemical resistance properties, and has fast hardness development properties. 收起 | |
| Picassian® PU-508 | Stahl Polymers | Picassian® PU-508 is a soft polyether aromatically modified polyurethane resin. It is used in flexo and gravure printing inks, in overprint varnishes, and in plasticizing grades of laminating inks. This product is tin free, TDI free, has good flexibility ...展开 Picassian® PU-508 is a soft polyether aromatically modified polyurethane resin. It is used in flexo and gravure printing inks, in overprint varnishes, and in plasticizing grades of laminating inks. This product is tin free, TDI free, has good flexibility properties, has good heat seal resistance properties, and has good adhesion on aluminium foil. 收起 | |
| Picassian® PU-518 | Stahl Polymers | Picassian® PU-518 is a non reactive, high molecular weighted, semi aliphatic polyether modified polyurethane resin. It is used in flexo and gravure inks, and as an adhesive promoter. This product is Tin free, TDI free, has good adhesion properties on alum...展开 Picassian® PU-518 is a non reactive, high molecular weighted, semi aliphatic polyether modified polyurethane resin. It is used in flexo and gravure inks, and as an adhesive promoter. This product is Tin free, TDI free, has good adhesion properties on aluminium foil, is soluble in alcohol rich mixtures, and is fully compatible with alcohol soluble nitrocellulose. 收起 | |
| Picassian® PU-546 | Stahl Polymers | Picassian® PU-546 is a non reactive, film forming, seal aliphatic, polyether modified polyurethane resin. It is used in flexo and gravure printing inks primarily, This product is tin free, TDI free, has pigment wetting attributes, is soluble in alcohol ri...展开 Picassian® PU-546 is a non reactive, film forming, seal aliphatic, polyether modified polyurethane resin. It is used in flexo and gravure printing inks primarily, This product is tin free, TDI free, has pigment wetting attributes, is soluble in alcohol rich mixtures, and has solvent retention values that are lower than those of conventional inks. 收起 | |
| Picassian® PU-548 | Stahl Polymers | Picassian® PU-548 is a non reactive, moderately tough, aromatic, polyester modified polyurethane resin. It is used as an adhesion promoter in gravure inks primarily. This product is tin free, TDI free, has good compatibility with other alcohol soluble res...展开 Picassian® PU-548 is a non reactive, moderately tough, aromatic, polyester modified polyurethane resin. It is used as an adhesion promoter in gravure inks primarily. This product is tin free, TDI free, has good compatibility with other alcohol soluble resins, and is very resistant to oils, water, and fats. 收起 | |
| Picassian® PU-551 | Stahl Polymers | Picassian® PU-551 is a film forming, semi-aliphatic, polyether modified polyurethane resin. It is used in sole binder inks, high speed flexo printing, and print plastics. This product has no webbing effect, has good adhesion properties, good dispersing pr...展开 Picassian® PU-551 is a film forming, semi-aliphatic, polyether modified polyurethane resin. It is used in sole binder inks, high speed flexo printing, and print plastics. This product has no webbing effect, has good adhesion properties, good dispersing properties, good wetting properties, good flow properties, good flexibility properties, and good blocking resistance properties. 收起 | |
| Picassian® PU-559 | Stahl Polymers | Picassian® PU-559 is a non reactive, moderately tough, aliphatic, polyether modified polyurethane resin. It is used in high performance flexo inks, high performance gravure inks, and non yellowing nitrocellulose based gravure inks. This product provides g...展开 Picassian® PU-559 is a non reactive, moderately tough, aliphatic, polyether modified polyurethane resin. It is used in high performance flexo inks, high performance gravure inks, and non yellowing nitrocellulose based gravure inks. This product provides good adhesion properties when used on polyolefin flims, has good compatibility with many kinds of resins, has good resistance properties with water, and many types of fat and oil. 收起 | |
| Picassian® PU-635 | Stahl Polymers | Picassian® PU-635 is an aqueous, non ionic dispersion of an aliphatic polyester urethane. It is used in leather basecoats, and in textiles. This product has low hardness properties, gives films high elongation properties, gives films good flexibility prop...展开 Picassian® PU-635 is an aqueous, non ionic dispersion of an aliphatic polyester urethane. It is used in leather basecoats, and in textiles. This product has low hardness properties, gives films high elongation properties, gives films good flexibility properties, is crosslinkable at room temperature, and is highly compatible with other binders. 收起 | |
| Picassian® PU-648 | Stahl Polymers | Picassian® PU-648 is a waterbased anionic dispersion of an aliphatic polyether urethane. It is used in leather basecoats, textiles, and graphic arts. This product is solvent free, has good UV resistance properties, low water absorption properties, good co...展开 Picassian® PU-648 is a waterbased anionic dispersion of an aliphatic polyether urethane. It is used in leather basecoats, textiles, and graphic arts. This product is solvent free, has good UV resistance properties, low water absorption properties, good coverage properties, good filling properties, and maintains flexibility at negative 30 degrees Celsius. 收起 | |
| PSA-1170 | NuSil Silicone Technology 1 | PSA-1170 is a one-part, non-curing, pressure sensitive silicone adhesive that has a translucent appearance and a low viscosity. It can be used for temporarily adhering to various substrates such as silicone, glass, metals, and organic rubbers. PSA-1170 is...展开 PSA-1170 is a one-part, non-curing, pressure sensitive silicone adhesive that has a translucent appearance and a low viscosity. It can be used for temporarily adhering to various substrates such as silicone, glass, metals, and organic rubbers. PSA-1170 is supplied in flammable solvents so it needs to be handled cautiously. Allow solvent to evaporate before adhering or attaching adhesive-coated objects together. 收起 | |
| R-1008-0 | NuSil Silicone Technology 1 | R-1008-0 is a translucent, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating mus...展开 R-1008-0 is a translucent, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 收起 | |
| R-1008-1 | NuSil Silicone Technology 1 | R-1008-1 is a white, RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating t...展开 R-1008-1 is a white, RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F).This product can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. 收起 | |
| R-1008-2 | NuSil Silicone Technology 1 | R-1008-2 is a black RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion, and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating t...展开 R-1008-2 is a black RTV silicone coating and marking ink that is a one part, flowable silicone elastomer dispersion, and cures in 7 days at room temperature when exposed to atmospheric moisture. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F).This product can be used on silicone rubber parts as a marking ink where the coating must maintain long term stability. 收起 | |
| R-1008-8 | NuSil Silicone Technology 1 | R-1008-8 is a violet, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must mai...展开 R-1008-8 is a violet, one part, flowable silicone elastomer dispersion that cures in 7 days at room temperature when exposed to atmospheric moisture. It can be used as a marking ink for silicone rubber parts and other components where the coating must maintain long term stability. It is best used for applications that require an operating temperature of 65°C to 260°C (-85°F to 465°F). 收起 | |
| R-1130 | NuSil Silicone Technology 1 | R-1130 is a non-corrosive, rapid curing, nun-slumping RTV silicone adhesive that can be used as a coating for semi-conductors and integrated circuits. It can also be utilized as an adhesive/sealant for electrical wires, terminals, mounting resistors and ...展开 R-1130 is a non-corrosive, rapid curing, nun-slumping RTV silicone adhesive that can be used as a coating for semi-conductors and integrated circuits. It can also be utilized as an adhesive/sealant for electrical wires, terminals, mounting resistors and connectors. It is ideal for overhead or side wall applications due to its non-slumping characteristics. 收起 | |
| R-1140 | NuSil Silicone Technology 1 | R-1140 is a one part, translucent, non-slumping silicone adhesive that is supplied in ready to use Semco® cartridges. This product bonds aggressively to most surfaces including glass, ceramics, metals, natural and synthetic fibers, wood, painted surfaces ...展开 R-1140 is a one part, translucent, non-slumping silicone adhesive that is supplied in ready to use Semco® cartridges. This product bonds aggressively to most surfaces including glass, ceramics, metals, natural and synthetic fibers, wood, painted surfaces and other silicone rubbers. It is best used for applications that require an operating temperature rang of 65 to 240°C (-85 to 465°F). 收起 | |
| R-2100-1 | NuSil Silicone Technology 1 | R-2100-1 is a white silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...展开 R-2100-1 is a white silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2100-2 | NuSil Silicone Technology 1 | R-2100-2 is a black silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...展开 R-2100-2 is a black silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2100-3 | NuSil Silicone Technology 1 | R-2100-3 is a red silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal ...展开 R-2100-3 is a red silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2100-6 | NuSil Silicone Technology 1 | R-2100-6 is a green silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is idea...展开 R-2100-6 is a green silicone ink that has a strong adhesion to other silicones and is dipersed in Xylene. It is designed to be used in application that require a rapid cure schedule and it provides a high capacity for single print applications. It is ideal as a marking ink on silicone parts as well as other components where the coating must demonstrate a long-term stability. 收起 | |
| R-2145 | NuSil Silicone Technology 1 | R1-2145 is an extremely tough gray silicone adhesive that does not require atmospheric moisture to cure and the product is available in easy to use, airless side by side kits that eliminate mixing and deairing. It rapidly cures at room temperature by appl...展开 R1-2145 is an extremely tough gray silicone adhesive that does not require atmospheric moisture to cure and the product is available in easy to use, airless side by side kits that eliminate mixing and deairing. It rapidly cures at room temperature by applying heat in an oven or a heat gun or lamp. This adhesive can be used for bonding and sealing silicones to each other and other substrates such as metals and plastics. It is ready for rapid production or prototyping due to the a rapid cure. 收起 | |
| R-2634 | NuSil Silicone Technology 1 | R-2634 is a two-part, electrically conductive RTV silicone that is designed for enhanced performance in extreme high and low temperatures. It can be used as an adhesive to bond covers on housings or where grooves and other configurations require a non-flo...展开 R-2634 is a two-part, electrically conductive RTV silicone that is designed for enhanced performance in extreme high and low temperatures. It can be used as an adhesive to bond covers on housings or where grooves and other configurations require a non-flowable material. This product is especially useful for sealing formed-in-place conductive gaskets and grounding connections. It can also be used for EMI and RFI shielding for aerospace and electrical applications. 收起 | |
| R-2949 | NuSil Silicone Technology 1 | R-2949 is a two-part, white, thermally conductive silicone that can cure rapidly with the addition of heat. It is an ideal product to be used in applications that require protection against extreme low and high temperatures. It can be used as an adhesive ...展开 R-2949 is a two-part, white, thermally conductive silicone that can cure rapidly with the addition of heat. It is an ideal product to be used in applications that require protection against extreme low and high temperatures. It can be used as an adhesive to bond openings in housings and modules where grooves or other configurations require a limited flow material with moderate thermal conductivity. It can also provide the transfer of heat between electrical components and their heat sinks. 收起 | |
| R-3930 | NuSil Silicone Technology 1 | R-3930 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It is designed for spraying, dip casting, and RTV curing of thin elastomeric films. It can also be utilized for...展开 R-3930 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It is designed for spraying, dip casting, and RTV curing of thin elastomeric films. It can also be utilized for bonding, coating, and sealing applications that require solvent and/or fuel resistance. It bonds aggressively to most surfaces and can help minimize ice adhesion. 收起 | |
| R-3975 | NuSil Silicone Technology 1 | R-3975 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It can be utilized for bonding, coating, and sealing applications that require solvent and/or fuel resistance. ...展开 R-3975 is a one-part RTV silicone elastomer dispersed in tert butyl acetate and the slight addition of heat will accelerate the curing process. It can be utilized for bonding, coating, and sealing applications that require solvent and/or fuel resistance. It bonds aggressively to most surfaces and can help minimize ice adhesion. It is designed for spraying, dip casting, and RTV curing of thin elastomeric films. 收起 | |
| R1-2145 | NuSil Silicone Technology 1 | R1-2145 is an extremely tough gray silicone adhesive that rapidly cures at room temperature by applying heat in an oven or a heat gun or lamp. It does not require atmospheric moisture to cure and the product is available in easy to use, airless side by si...展开 R1-2145 is an extremely tough gray silicone adhesive that rapidly cures at room temperature by applying heat in an oven or a heat gun or lamp. It does not require atmospheric moisture to cure and the product is available in easy to use, airless side by side kits that eliminate mixing and deairing, This adhesive can be used for bonding and sealing silicones to each other and other substrates such as metals and plastics. It is ready for rapid production or prototyping due to the a rapid cure. 收起 | |
| R1-3930-11 | NuSil Silicone Technology 1 | R1-3930-11 is a gray fluorosilicone, adhesive, sealant, and coating that bonds aggressively to most surfaces. This product can be utilized for sealing, coating, and bonding applications that require solvent and/or fuel resistance. It can also be used for ...展开 R1-3930-11 is a gray fluorosilicone, adhesive, sealant, and coating that bonds aggressively to most surfaces. This product can be utilized for sealing, coating, and bonding applications that require solvent and/or fuel resistance. It can also be used for bonding or protecting hardware components exposed to gasoline or aviation fuels. It can be further dispersed for spraying applications. 收起 | |
| R3-2160 | NuSil Silicone Technology 1 | R3-2160 is a two-part, pourable silicone system that has a high tear strength and good physical properties. It is designed for enhance performance in extreme high and low temperatures. The ideal use for this high temperature adhesive/sealant is for pottin...展开 R3-2160 is a two-part, pourable silicone system that has a high tear strength and good physical properties. It is designed for enhance performance in extreme high and low temperatures. The ideal use for this high temperature adhesive/sealant is for potting connectors, seals and gaskets, molded high voltage terminals, and cable harness breakouts. 收起 | |
| R3-3930-11 | NuSil Silicone Technology 1 | R3-3930-11 is a gray, two-part, RTV silicone that can be further dispersed for spraying applications. It has strong physical attributes which make it bond aggressively to most surfaces. It can also be utilized in applications where coating, sealing, and ...展开 R3-3930-11 is a gray, two-part, RTV silicone that can be further dispersed for spraying applications. It has strong physical attributes which make it bond aggressively to most surfaces. It can also be utilized in applications where coating, sealing, and bonding are necessary for fuel and /or solvent resistance.This product can be used to bond or protect hardware components that are exposed to gasoline or aviation fuels. 收起 |
