| ACCULIN® 1000 (2071A) | The International Group, Inc. (IGI Wax) | ACCULIN® 1000 is a hard, high melting point polyethylene. | |
| ACCULIN® 1500 (2057A) | The International Group, Inc. (IGI Wax) | ACCULIN® 1500 is an extremely pure, inert, narrow melt point product that exhibits very specific expansion behavior. | |
| ACCULIN® 1500 (2073A) | The International Group, Inc. (IGI Wax) | ACCULIN® 1500 is a hard, low melting point polyethylene. | |
| ACCULIN® 2000 (2074A) | The International Group, Inc. (IGI Wax) | ACCULIN® 2000 is a hard, high melting point polyethylene. | |
| ACCULIN® 500 (2056A) | The International Group, Inc. (IGI Wax) | ACCULIN® 500 is a hard, low melting point polyethylene. | |
| ACCULIN® 600 (2059A) | The International Group, Inc. (IGI Wax) | ACCULIN® 600 is a hard, low melting point polyethylene. | |
| ACCULIN® 655 (2061A) | The International Group, Inc. (IGI Wax) | ACCULIN® 655 is a hard, low melting point polyethylene. | |
| ACCULIN® 725 (2063A) | The International Group, Inc. (IGI Wax) | ACCULIN® 725 is a hard, low melting point polyethylene. | |
| Aquaban® 9001A | The International Group, Inc. (IGI Wax) | Aquaban® 9001A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. This product should be diluted with water before use, depending upon protection required. Typical dilution ...展開 Aquaban® 9001A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. This product should be diluted with water before use, depending upon protection required. Typical dilution is 1:1 with water. 收起 | |
| Aquaban® 9009A | The International Group, Inc. (IGI Wax) | Aquaban® 9009A is a water-based treatment for paper and corrugated board. It imparts a high level of water repellence. | |
| Aquaban® 9010A | The International Group, Inc. (IGI Wax) | Aquaban® 9010A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. For corrugated application, the product should be diluted with water before use, depending upon protection ...展開 Aquaban® 9010A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. For corrugated application, the product should be diluted with water before use, depending upon protection required. Typical dilution is 1:1 with water. For general purpose application other than corrugated, the product can be used without dilution. 收起 | |
| ASTORLITE® J50 (4636A) | The International Group, Inc. (IGI Wax) | ASTORLITE® J50 is a soft, white, opaque wax specially designed for jar / container candles. Its cohesive strength and low shrinkage allow it to adhere to the container. Jar / container candles can be made with a single filling with no top-off necessary. | |
| Bake-Guard 9156A | The International Group, Inc. (IGI Wax) | Bake-Guard 9156A is a high performance water-based coating for corrugated board and paper substrates where exceptional grease and water resistance are required. Other unique features of this product are its high angle of slide and ease of printability. | |
| Barrier-Grip 9471A | The International Group, Inc. (IGI Wax) | Barrier-Grip 9471A is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Grip 9471B | The International Group, Inc. (IGI Wax) | Barrier-Grip 9471B is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Grip 9472B | The International Group, Inc. (IGI Wax) | Barrier-Grip 9472B is a water-based coating designed as an economical pre-coat for application onto kraft liners or other paper substrates. It seals the substrate and provides a uniform surface onto which functional coatings may be applied, optimising the...展開 Barrier-Grip 9472B is a water-based coating designed as an economical pre-coat for application onto kraft liners or other paper substrates. It seals the substrate and provides a uniform surface onto which functional coatings may be applied, optimising the performance of the functional coatings. 收起 | |
| Barrier-Grip R5701H | The International Group, Inc. (IGI Wax) | Barrier-Grip R5701H is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Grip R6709A | The International Group, Inc. (IGI Wax) | Barrier-Grip R6709A is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Seal R6728A | The International Group, Inc. (IGI Wax) | Barrier-Seal R6728A is a water-based coating designed for SBS cup stock and other paper based substrates. It can be used for any packaging application that requires excellent water resistance, oil resistance and heat seal. | |
| C Glass Flake GF007/C | Glassflake Ltd | C Glass Flake GF007/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting i...展開 C Glass Flake GF007/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in a wider thickness specification. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| C Glass Flake GF750/C | Glassflake Ltd | C Glass Flake GF750/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting i...展開 C Glass Flake GF750/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in a wider thickness specification. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| C Glass Flake GF750MC | Glassflake Ltd | C Glass Flake GF750MC is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/-2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in...展開 C Glass Flake GF750MC is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/-2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in a wider thickness specification. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF001 | Glassflake Ltd | ECR Glass Flake GF001 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF001 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF002 | Glassflake Ltd | ECR Glass Flake GF002 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.3 - 2.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF002 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.3 - 2.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF003 | Glassflake Ltd | ECR Glass Flake GF003 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 2.3 - 3.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF003 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 2.3 - 3.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF005 | Glassflake Ltd | ECR Glass Flake GF005 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties ...展開 ECR Glass Flake GF005 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF007 | Glassflake Ltd | ECR Glass Flake GF007 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF007 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100M (Milled) | Glassflake Ltd | ECR Glass Flake GF100M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF100M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100M (Unmilled) | Glassflake Ltd | ECR Glass Flake GF100 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier p...展開 ECR Glass Flake GF100 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF100nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF100nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF100nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF100nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF350nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF350nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF350nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF350nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF350nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF350nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500M (Milled) | Glassflake Ltd | ECR Glass Flake GF500M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF500M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500M (Unmilled) | Glassflake Ltd | ECR Glass Flake GF500 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier p...展開 ECR Glass Flake GF500 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF500nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF500nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF500nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF500nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750M (Milled) | Glassflake Ltd | ECR Glass Flake GF750 (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF750 (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750M (Unmilled) | Glassflake Ltd | ECR Glass Flake GF750 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier p...展開 ECR Glass Flake GF750 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF750nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF750nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF750nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF750nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| EVACOTE® 7089A | The International Group, Inc. (IGI Wax) | EVACOTE® 7089A is a specialty formulation of petroleum waxes and polymers suitable in consistency to be utilized as a sealant and coating for fertilizer applications. | |
| EVACOTE® 7292C | The International Group, Inc. (IGI Wax) | EVACOTE® 7292C is a premium multi-component formulation having good barrier properties against both water and moisture vapor. Its low viscosity might assist in achieving better machinability for application. | |
| EXOCOAT™ AM | Axcentive Sarl | EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down v...展開 EXOCOAT® AM by Axcentive is a water-based, doped nano-titanium oxide sol with a strong antimicrobial effect and anatase structure. It prevents the build-up of microbes as the photocatalytic effect results in effective radical formation which breaks down viruses and bacteria. It eradicates viruses such as influenza, SARS-COV-2, dengue & hepatitis and bacteria such as E. coli, MSRA, streptococcus, listeria, pneumonia, and salmonella. It is activated by light and displays quick drying at room temperature. Spray application is recommended to reach thin monolayers. It exhibits curing at room temperature up to 300°C and super hard particles (1GPa Vickers). It is easy to apply & durable, allowing longer disinfection intervals while preserving hygiene level. It shows non-silver leaching, efficacious even under low light conditions, lower service frequency, and no need for frequent disinfection routine. It is used in the state-of-the-art continuous antimicrobial coating for high-traffic areas. EXOCOAT® AM is suitable for topcoats for any surface inside buildings, stores, hospitals, and vehicles. The shelf life of this product is 9 months. 收起 | |
| Hanos ASP-100F | Hanwha Chemical Corporation | Hanos ASP-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechan...展開 Hanos ASP-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechanical strength. This product is well suited for use in conductive transparent electrodes, conductive nano ink, conductive heating films, nano device, nano-bio material and chemical sensors. 收起 | |
| Hanos AST-100F | Hanwha Chemical Corporation | Hanos AST-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechan...展開 Hanos AST-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechanical strength. This product is well suited for use in conductive transparent electrodes, conductive nano ink, conductive heating films, nano device, nano-bio material and chemical sensors. 收起 | |
| Hanos MWCNT CM-150 | Hanwha Chemical Corporation | Hanos MWCNT CM-150 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-150 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-150 Composite material is well suited for the production of ESD, EMI shielding, reinforced material, heat exchangers, etc. 收起 | |
| Hanos MWCNT CM-250 | Hanwha Chemical Corporation | Hanos MWCNT CM-250 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-250 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-250 Composite material is well suited for the production of for inks & paste, ESD, EMI Shielding, reinforced materials, heat exchanger, etc. 收起 | |
| Hanos MWCNT CM-280 | Hanwha Chemical Corporation | Hanos MWCNT CM-280 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-280 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-280 Composite material is well suited for the production of for inks & paste, ESD, EMI Shielding, reinforced materials, heat exchanger, etc. 收起 | |
| Hanos MWCNT CM-350 | Hanwha Chemical Corporation | Hanos MWCNT CM-350 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-350 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-350 Composite material is well suited for the production of for inks & paste, ESD, EMI Shielding, reinforced materials, heat exchanger, etc. 收起 | |
| Hanos PS Compound / Sheet | Hanwha Chemical Corporation | Hanos PS Compound / Sheet is a conductive product for Electrostatic Dissipative(ESD) or antistatic purpose with special CNT layers. It can be used in various industrial areas to prevent electrical damages of target products. It is well suited for use as a...展開 Hanos PS Compound / Sheet is a conductive product for Electrostatic Dissipative(ESD) or antistatic purpose with special CNT layers. It can be used in various industrial areas to prevent electrical damages of target products. It is well suited for use as a filler in the production of sheets or as a black pigment in inks and paints. 收起 | |
| Hanos PS Ink | Hanwha Chemical Corporation | Hanos PS Ink is a PP pellet coating ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applicati...展開 Hanos PS Ink is a PP pellet coating ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications such as conductive films or inks for chip trays. 收起 | |
| Hanos SW01 | Hanwha Chemical Corporation | Hanos SW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications ...展開 Hanos SW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications such as conductive films or inks for chip trays. 收起 | |
| Hanos TW01 | Hanwha Chemical Corporation | Hanos TW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications ...展開 Hanos TW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications such as conductive films or inks for chip trays. 收起 | |
| Hanwha 2-EH (2-Ethyl-1-Hexanol) | Hanwha Chemical Corporation | Hanwha 2-EH is an colorless, transparent liquid made of 2-Ethyl-1-Hexanol. It is primarily used as the main ingredient in the production of certain types of plasticizers. It is well suited for use in making solvents, stabilizers and acrylates as well. | |
| Hanwha CP-430 | Hanwha Chemical Corporation | Hanwha CP-430 is a Vinyl Chloride-Vinyl Acetate Copolymer with outstanding solvent solubility, adhesion, transparency and liquidity. CP-430 is well suited for use in the production of Gravure inks, adhesives and paints. | |
| Hanwha CP-450 | Hanwha Chemical Corporation | Hanwha CP-450 is a Vinyl Chloride-Vinyl Acetate Copolymer with outstanding solvent solubility, adhesion, transparency and liquidity. CP-450 is well suited for use in the production of inks, adhesives and paints. | |
| Hanwha CP-710 | Hanwha Chemical Corporation | Hanwha CP-710 is a Vinyl Chloride-Vinyl Acetate Copolymer with outstanding solvent solubility, adhesion, transparency and liquidity. CP-710 is well suited for use in the production of inks, adhesives and paints. | |
| Hanwha DIDP (Diisodecyl Phthalate) | Hanwha Chemical Corporation | Hanwha DIDP is a transparent plasticizer made of Diisononyl Phthalate with excellent viscosity and outstanding electrical insulation. It is well suited for use in the production of films, sheets, leathers, wire coatings, wall papers and flooring materials...展開 Hanwha DIDP is a transparent plasticizer made of Diisononyl Phthalate with excellent viscosity and outstanding electrical insulation. It is well suited for use in the production of films, sheets, leathers, wire coatings, wall papers and flooring materials where ever cold, light and chemicals resistance is required. 收起 | |
| Hanwha I-BuOH (2-Methylpropan-1-Ol) | Hanwha Chemical Corporation | Hanwha I-BuOH is an colorless, transparent liquid made of 2-Methylpropan-1-Ol. It is primarily used as the main ingredient in the production of certain types of plasticizers. It is well suited for use in making solvents and amino resins as well. | |
| Hanwha MA (High-purity Maleic Anhydride) | Hanwha Chemical Corporation | Hanwha MA is a pure white flaky solid at room temperature that when heated becomes a colorless transparent liquid. Made of a High-purity Maleic Anhydride, it is primarily used in the production of resins. It can also be used in the production of FRP paint...展開 Hanwha MA is a pure white flaky solid at room temperature that when heated becomes a colorless transparent liquid. Made of a High-purity Maleic Anhydride, it is primarily used in the production of resins. It can also be used in the production of FRP paints, dyes and pigments. 收起 | |
| Hanwha N-BuOH (N-Butyl Alcohol) | Hanwha Chemical Corporation | Hanwha N-BuOH is an colorless, transparent liquid made of N-Butyl Alcohol. It is primarily used as the main ingredient in the production of certain types of plasticizers. It is well suited for use in making solvents, stabilizers and acrylates as well. | |
| Hanwha PA (High-purity Phthalic Anhydride) | Hanwha Chemical Corporation | Hanwha PA is a pure white flaky solid at room temperature that when heated becomes a colorless transparent liquid. Made of High-purity Phthalic Anhydride, it is primarily used in the production of phthalate plasticizers. It can also be used in the product...展開 Hanwha PA is a pure white flaky solid at room temperature that when heated becomes a colorless transparent liquid. Made of High-purity Phthalic Anhydride, it is primarily used in the production of phthalate plasticizers. It can also be used in the production of FRP paints and spandex. 收起 | |
| Hanwha TP-400M | Hanwha Chemical Corporation | Hanwha TP-400M is a PVC resin made from a terpolymer with outstanding adhesion to metals. It is well suited for use in the production of metal coatings, paints and aluminum printing inks. | |
| HCCFlex SP-390 | Hanwha Chemical Corporation | HCCFlex SP-390 is a Non-phthalate plasticizer made of Dioctyl Terephthalate (DOTP) which is non-carcinogenic and contains no environmental hormones. It is well suited for use in the production of films, sheets, leathers, flooring materials, wall papers a...展開 HCCFlex SP-390 is a Non-phthalate plasticizer made of Dioctyl Terephthalate (DOTP) which is non-carcinogenic and contains no environmental hormones. It is well suited for use in the production of films, sheets, leathers, flooring materials, wall papers and wire coatings. 收起 | |
| IGI® 0431G | The International Group, Inc. (IGI Wax) | IGI® 0431G is a crude paraffin slack wax with relatively high oil content and melting point. | |
| IGI® 1230A | The International Group, Inc. (IGI Wax) | IGI® 1230A is a fully refined paraffin wax. | |
| IGI® 1239A | The International Group, Inc. (IGI Wax) | IGI® 1239A is a fully refined wax with a mid-range melting point. | |
| IGI® 1250A | The International Group, Inc. (IGI Wax) | IGI® 1250A is a fully refined paraffin wax. | |
| IGI® 1260A | The International Group, Inc. (IGI Wax) | IGI® 1260A is a fully refined paraffin wax. | |
| IGI® 1297A | The International Group, Inc. (IGI Wax) | IGI® 1297A is a fully refined paraffin wax with excellent heat stability. | |
| IGI® 1303A | The International Group, Inc. (IGI Wax) | IGI® 1303A is a fully refined high-melt paraffin wax that is used in a variety of applications including: hot-melt adhesives, investment casting, rubber products and textiles. | |
| IGI® 2202A | The International Group, Inc. (IGI Wax) | IGI® 2202A is a semi-refined, low-melt, scale wax that is used in a variety of applications including; candles and chlorination. | |
| IGI® 2251A | The International Group, Inc. (IGI Wax) | IGI® 2251A is a flexible physiotherapy wax. IGI® 2251A is a low melting wax that is totally transparent (clear) at 125°F (52°C). | |
| IGI® 2281A | The International Group, Inc. (IGI Wax) | IGI® 2281A is a specially selected grade of white crude scale wax possessing good flexibility as well as high gloss on air cooling. IGI® 2281A is ideal for use in container candles or as a coating wax for vegetables. The storage life of vegetables such as...展開 IGI® 2281A is a specially selected grade of white crude scale wax possessing good flexibility as well as high gloss on air cooling. IGI® 2281A is ideal for use in container candles or as a coating wax for vegetables. The storage life of vegetables such as turnips is improved by prevention of loss of moisture, while appearance is enhanced for improved marketability. Because it maintains flexibility at refrigerated temperatures, chipping and cracking of the coating is minimized when compared to other waxes. 收起 | |
| IGI® 2288A | The International Group, Inc. (IGI Wax) | IGI® 2288A is a refined scale wax designed for heat therapy of arthritic and related ailments. It has a low melting point to avoid discomfort on application, and solidifies to form a soft, flexible coating which is easily peeled from the skin. As IGI® 228...展開 IGI® 2288A is a refined scale wax designed for heat therapy of arthritic and related ailments. It has a low melting point to avoid discomfort on application, and solidifies to form a soft, flexible coating which is easily peeled from the skin. As IGI® 2288A solidifies, it continues to release heat to the treated area. 收起 | |
| IGI® 2289A | The International Group, Inc. (IGI Wax) | IGI® 2289A is a crude scale paraffin wax derived from petroleum. | |
| IGI® 6006A | The International Group, Inc. (IGI Wax) | IGI® 6006A is a specialty wax formulation for “one pour” container candles. | |
| IGI® 6027A | The International Group, Inc. (IGI Wax) | IGI® 6027A is a specialty formulation for container candles. | |
| IGI® 6028A | The International Group, Inc. (IGI Wax) | IGI® 6028A is a specialty formulation of vegetable derived waxes and petroleum derived waxes suitable in consistency to be used for the manufacture of pillar, votive and other molded candles. | |
| IGI® 6046A | The International Group, Inc. (IGI Wax) | IGI® 6046A is a specialty formulation for use in container candles. | |
| Ketjenflex® 12 | Axcentive Sarl | Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl com...展開 Ketjenflex® 12 is a citrate based clear liquid. It is used as a partially bio-based plasticizer for inks, adhesives, and coatings. Ketjenflex® 12 can be used in vinyl formulations such as PVC plastics, vinyl flooring, solution vinyl resins, wood vinyl compounds, and PVC based plastisols. It can also be used in PVC based polymers, nitrocellulose resins, and cyanoacrylate adhesives. 收起 | |
| Ketjenflex® 6 | Axcentive Sarl | Ketjenflex® 6 is a toluene sulfonamide in the form of a white crystalline powder. It is used as a plasticizer in inks, adhesives, and coatings. Ketjenflex® 6 can be used with resins such as nitrocellulose, polyamide, PVAC, rosin, epoxy, and more. | |
| Ketjenflex® 8 | Axcentive Sarl | Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coa...展開 Ketjenflex® 8 is a toluene sulfonamide in the form of a clear, slightly yellow liquid. It is used as a plasticizer and adhesion promoter in inks, adhesives, and coatings. Ketjenflex® 8 can be used with applications such as PVAC, nitrocellulose, powder coatings, synthetic polyamides, epoxy coatings and adhesives, and more. 收起 | |
| Ketjenflex® CP | Axcentive Sarl | Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings. | |
| Ketjenflex® MH | Axcentive Sarl | Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printi...展開 Ketjenflex® MH is a toluene sulfonamide in the form of a hard, transparent resin. It is used at a plasticizing co-resin in coatings, adhesives, and inks. Ketjenflex® MH can be used in nitrocellulose coatings, epoxy based coatings and adhesives, and printing inks. 收起 | |
| Ketjenflex® MS 80 | Axcentive Sarl | Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured in...展開 Ketjenflex® MS 80 is a toluene sulfonamide in the form of a transparent liquid. it is used as a plasticizing co-resin in butyl acetate for coatings, adhesives, and inks. Ketjenflex® MS 80 is the liquid version of Ketjenflex® MH and can easily be poured into desired formulations. It has applications in nitrocellulose coatings, cellulose acetate formulations, and printing inks. 收起 | |
| LA Glass Flake GF001LA | Glassflake Ltd | LA Glass Flake GF001LA is a Low Alkali Glassflake, or LAG, which has been formulated specifically for use as a pigment substrate, giving the finished product unique effects. Glass flakes, or borosilicates as they are often referred to, are a unique substr...展開 LA Glass Flake GF001LA is a Low Alkali Glassflake, or LAG, which has been formulated specifically for use as a pigment substrate, giving the finished product unique effects. Glass flakes, or borosilicates as they are often referred to, are a unique substrate which, unlike natural micas and synthetic micas, have a completely planar and smooth surface. They are also completely transparent, giving rise to effect pigments coated with metal oxides that display high brightness, good color purity, and high chroma. Presently glass flake pigments are used in both cosmetic and industrial applications including automotive coatings. 收起 | |
| LA Glass Flake GF100LA | Glassflake Ltd | LA Glass Flake GF100LA is a Low Alkali Glassflake, or LAG, which has been formulated specifically for use as a pigment substrate, giving the finished product unique effects. Glass flakes, or borosilicates as they are often referred to, are a unique substr...展開 LA Glass Flake GF100LA is a Low Alkali Glassflake, or LAG, which has been formulated specifically for use as a pigment substrate, giving the finished product unique effects. Glass flakes, or borosilicates as they are often referred to, are a unique substrate which, unlike natural micas and synthetic micas, have a completely planar and smooth surface. They are also completely transparent, giving rise to effect pigments coated with metal oxides that display high brightness, good color purity, and high chroma. Presently glass flake pigments are used in both cosmetic and industrial applications including automotive coatings. 收起 | |
| LA Glass Flake GF100MLA | Glassflake Ltd | LA Glass Flake GF100MLA is a Low Alkali Glassflake, or LAG, which has been formulated specifically for use as a pigment substrate, giving the finished product unique effects. Glass flakes, or borosilicates as they are often referred to, are a unique subst...展開 LA Glass Flake GF100MLA is a Low Alkali Glassflake, or LAG, which has been formulated specifically for use as a pigment substrate, giving the finished product unique effects. Glass flakes, or borosilicates as they are often referred to, are a unique substrate which, unlike natural micas and synthetic micas, have a completely planar and smooth surface. They are also completely transparent, giving rise to effect pigments coated with metal oxides that display high brightness, good color purity, and high chroma. Presently glass flake pigments are used in both cosmetic and industrial applications including automotive coatings. 收起 | |
| MICROSERE® 5788A | The International Group, Inc. (IGI Wax) | MICROSERE® 5788A is a unique, low-melt microcrystalline wax that is used in a variety of applications including paper packaging and candles. | |
| MICROSERE® 5806A | The International Group, Inc. (IGI Wax) | MICROSERE® 5806A is a high-melt, amber colored microcrystalline that is used in a variety of applications. | |
| MICROSERE® 5871A | The International Group, Inc. (IGI Wax) | MICROSERE® 5871A is a light colored, high-melt, microcrystalline wax that is used in a variety of applications. | |
| MICROSERE® 5890A | The International Group, Inc. (IGI Wax) | MICROSERE® 5890A is a white, high-melt, microcrystalline wax that is used in a variety of applications. MICROSERE® 5890A complies with the requirements for “Microcrystalline Wax” set by the United States Pharmacopeia (USP) / National Formulary (NF). | |
| MICROSERE® 5896A | The International Group, Inc. (IGI Wax) | MICROSERE® 5896A is a coating-grade, high melt, microcrystalline wax used in a variety of applications including; adhesives, candles, cosmetics, food coatings, inks, lubricants, personal care, polish, and textiles. | |
| MICROSERE® 5897A | The International Group, Inc. (IGI Wax) | MICROSERE® 5897A is a light colored, coating-grade, high melt, microcrystalline wax used in a variety of applications including; adhesives, candles, cosmetics, food coatings, inks, lubricants, personal care, polish, and textiles. | |
| MICROSERE® 5909A | The International Group, Inc. (IGI Wax) | MICROSERE® 5909A is a high-melt, microcrystalline wax that is used in a variety of applications including; plastics, adhesives, candles, cosmetics, food coatings, inks, lubricants, personal care, polish, and textiles. | |
| MICROSERE® 5910A | The International Group, Inc. (IGI Wax) | MICROSERE® 5910A is a high-melt, microcrystalline wax that is used in a variety of applications including; plastics, adhesives, candles, cosmetics, food coatings, inks, lubricants, personal care, polish, and textiles. | |
| MICROSERE® 5999A | The International Group, Inc. (IGI Wax) | MICROSERE® 5999A is an amber colored microcrystalline wax with hard consistency and a high melting point. | |
| Moonshine® AgFlake 100-100 (GFEAGF-1100) | Glassflake Ltd | Moonshine® AgFlake 100-100 are thin borosilicate glass flakes encapsulated in silver. They may be used for functional purposes as a conductive filler. They have an average particle size diameter of 100 μm. High conductivity can be achieved at low loadings...展開 Moonshine® AgFlake 100-100 are thin borosilicate glass flakes encapsulated in silver. They may be used for functional purposes as a conductive filler. They have an average particle size diameter of 100 μm. High conductivity can be achieved at low loadings. Agflakes are lightweight in contrast to equivalent pure metal fillers. They may be used as both a functional and a decorative pigment. Presently glass flake pigments are used in both cosmetic and industrial applications including automotive coatings. 收起 |
