| ACCULIN® 1000 (2071A) | The International Group, Inc. (IGI Wax) | ACCULIN® 1000 is a hard, high melting point polyethylene. | |
| ACCULIN® 1500 (2057A) | The International Group, Inc. (IGI Wax) | ACCULIN® 1500 is an extremely pure, inert, narrow melt point product that exhibits very specific expansion behavior. | |
| ACCULIN® 1500 (2073A) | The International Group, Inc. (IGI Wax) | ACCULIN® 1500 is a hard, low melting point polyethylene. | |
| ACCULIN® 2000 (2074A) | The International Group, Inc. (IGI Wax) | ACCULIN® 2000 is a hard, high melting point polyethylene. | |
| ACCULIN® 500 (2056A) | The International Group, Inc. (IGI Wax) | ACCULIN® 500 is a hard, low melting point polyethylene. | |
| ACCULIN® 600 (2059A) | The International Group, Inc. (IGI Wax) | ACCULIN® 600 is a hard, low melting point polyethylene. | |
| ACCULIN® 655 (2061A) | The International Group, Inc. (IGI Wax) | ACCULIN® 655 is a hard, low melting point polyethylene. | |
| ACCULIN® 725 (2063A) | The International Group, Inc. (IGI Wax) | ACCULIN® 725 is a hard, low melting point polyethylene. | |
| Aquaban® 9001A | The International Group, Inc. (IGI Wax) | Aquaban® 9001A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. This product should be diluted with water before use, depending upon protection required. Typical dilution ...展開 Aquaban® 9001A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. This product should be diluted with water before use, depending upon protection required. Typical dilution is 1:1 with water. 收起 | |
| Aquaban® 9009A | The International Group, Inc. (IGI Wax) | Aquaban® 9009A is a water-based treatment for paper and corrugated board. It imparts a high level of water repellence. | |
| Aquaban® 9010A | The International Group, Inc. (IGI Wax) | Aquaban® 9010A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. For corrugated application, the product should be diluted with water before use, depending upon protection ...展開 Aquaban® 9010A is a concentrated general purpose water-based treatment for paper and corrugated board. It imparts a high level of water repellence. For corrugated application, the product should be diluted with water before use, depending upon protection required. Typical dilution is 1:1 with water. For general purpose application other than corrugated, the product can be used without dilution. 收起 | |
| ASTORLITE® J50 (4636A) | The International Group, Inc. (IGI Wax) | ASTORLITE® J50 is a soft, white, opaque wax specially designed for jar / container candles. Its cohesive strength and low shrinkage allow it to adhere to the container. Jar / container candles can be made with a single filling with no top-off necessary. | |
| Bake-Guard 9156A | The International Group, Inc. (IGI Wax) | Bake-Guard 9156A is a high performance water-based coating for corrugated board and paper substrates where exceptional grease and water resistance are required. Other unique features of this product are its high angle of slide and ease of printability. | |
| Barrier-Grip 9471A | The International Group, Inc. (IGI Wax) | Barrier-Grip 9471A is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Grip 9471B | The International Group, Inc. (IGI Wax) | Barrier-Grip 9471B is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Grip 9472B | The International Group, Inc. (IGI Wax) | Barrier-Grip 9472B is a water-based coating designed as an economical pre-coat for application onto kraft liners or other paper substrates. It seals the substrate and provides a uniform surface onto which functional coatings may be applied, optimising the...展開 Barrier-Grip 9472B is a water-based coating designed as an economical pre-coat for application onto kraft liners or other paper substrates. It seals the substrate and provides a uniform surface onto which functional coatings may be applied, optimising the performance of the functional coatings. 收起 | |
| Barrier-Grip R5701H | The International Group, Inc. (IGI Wax) | Barrier-Grip R5701H is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Grip R6709A | The International Group, Inc. (IGI Wax) | Barrier-Grip R6709A is a water-based product that provides a high performance barrier against water and grease when applied to a paper based substrate. Coated surface also exhibits exceptionally high slide angle. | |
| Barrier-Seal R6728A | The International Group, Inc. (IGI Wax) | Barrier-Seal R6728A is a water-based coating designed for SBS cup stock and other paper based substrates. It can be used for any packaging application that requires excellent water resistance, oil resistance and heat seal. | |
| Benzidine Orange R | Emperor Pigment Co., Ltd. | Benzidine Orange R is a yellowish colored pigment that is used in solvent inks, aqueous inks, and aqueous coatings. It has a density value of 1.4 and a pH value of 7. This product has a color index number of Pigment Orange 16, a CAS number of 6505-28-8, a...展開 Benzidine Orange R is a yellowish colored pigment that is used in solvent inks, aqueous inks, and aqueous coatings. It has a density value of 1.4 and a pH value of 7. This product has a color index number of Pigment Orange 16, a CAS number of 6505-28-8, and an EU number of 229-388-1. 收起 | |
| Benzidine Yellow 121H | Emperor Pigment Co., Ltd. | Benzidine Yellow 121H is a pigment that is bright yellow in color. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used i...展開 Benzidine Yellow 121H is a pigment that is bright yellow in color. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used in PA inks, NC inks, PP inks, and Toluene based inks. 收起 | |
| Benzidine Yellow DHG | Emperor Pigment Co., Ltd. | Benzidine Yellow DHG is a bright yellow colored pigment that is used in offset inks and textile printing. It has a density value of 1.5 and a pH value of 6.0 to 7.0. This product has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, an...展開 Benzidine Yellow DHG is a bright yellow colored pigment that is used in offset inks and textile printing. It has a density value of 1.5 and a pH value of 6.0 to 7.0. This product has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. 收起 | |
| Benzidine Yellow G | Emperor Pigment Co., Ltd. | Benzidine Yellow G is a pigment that is reddish yellow and transparent in color. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5, a pH value of 6.0 to 7.0,...展開 Benzidine Yellow G is a pigment that is reddish yellow and transparent in color. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used in offset inks, waterbased inks, and textile printing. 收起 | |
| Benzidine Yellow G-A | Emperor Pigment Co., Ltd. | Benzidine Yellow G-A is a pigment that is reddish yellow in color. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used i...展開 Benzidine Yellow G-A is a pigment that is reddish yellow in color. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used in offset inks, waterbased inks, and textile printing. 收起 | |
| Benzidine Yellow G-B | Emperor Pigment Co., Ltd. | Benzidine Yellow G-B is a greenish yellow and semitransparent colored pigment that is used in offset inks, waterbased inks, and textile printing. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. T...展開 Benzidine Yellow G-B is a greenish yellow and semitransparent colored pigment that is used in offset inks, waterbased inks, and textile printing. It has a color index number of Pigment Yellow 12, a CAS number of 6358-85-6, and an EU number of 228-787-8. This product has a density value of 1.5 and a pH value of 6.0 to 7.0. 收起 | |
| Benzimidazolone Orange | Emperor Pigment Co., Ltd. | Benzimidazolone Orange is a pigment that is orange in color. It has a color index number of Pigment Orange 64 and a CAS number of 72102-84-2. This product has a heat stability value of 250 degrees Celsius, an oil absorption value of 40 to 60 grams per 100...展開 Benzimidazolone Orange is a pigment that is orange in color. It has a color index number of Pigment Orange 64 and a CAS number of 72102-84-2. This product has a heat stability value of 250 degrees Celsius, an oil absorption value of 40 to 60 grams per 100 grams, and is used in paints and printing inks. 收起 | |
| Benzimidazolone Orange HL | Emperor Pigment Co., Ltd. | Benzimidazolone Orange HL is an orange colored pigment that is used in offset inks, solvent inks, aqueous inks, and paints. It has a color index number of Pigment Orange 36, a CAS number of 12236-62-3, and an EU number of 235-462-4. This product has a den...展開 Benzimidazolone Orange HL is an orange colored pigment that is used in offset inks, solvent inks, aqueous inks, and paints. It has a color index number of Pigment Orange 36, a CAS number of 12236-62-3, and an EU number of 235-462-4. This product has a density value of 1.4 and a pH value of 6.5. 收起 | |
| C Glass Flake GF007/C | Glassflake Ltd | C Glass Flake GF007/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting i...展開 C Glass Flake GF007/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in a wider thickness specification. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| C Glass Flake GF750/C | Glassflake Ltd | C Glass Flake GF750/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting i...展開 C Glass Flake GF750/C is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/- 2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in a wider thickness specification. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| C Glass Flake GF750MC | Glassflake Ltd | C Glass Flake GF750MC is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/-2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in...展開 C Glass Flake GF750MC is a corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of Av. 5 +/-2 microns. The manufacturing process utilized by this flake differs from the normal spun-glass method, resulting in a wider thickness specification. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF001 | Glassflake Ltd | ECR Glass Flake GF001 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF001 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF002 | Glassflake Ltd | ECR Glass Flake GF002 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.3 - 2.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF002 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.3 - 2.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF003 | Glassflake Ltd | ECR Glass Flake GF003 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 2.3 - 3.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF003 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 2.3 - 3.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF005 | Glassflake Ltd | ECR Glass Flake GF005 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties ...展開 ECR Glass Flake GF005 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF007 | Glassflake Ltd | ECR Glass Flake GF007 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties a...展開 ECR Glass Flake GF007 is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100M (Milled) | Glassflake Ltd | ECR Glass Flake GF100M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF100M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100M (Unmilled) | Glassflake Ltd | ECR Glass Flake GF100 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier p...展開 ECR Glass Flake GF100 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 1.0 - 1.3μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF100nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF100nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF100nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF100nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF100nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.100nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF350nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF350nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF350nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF350nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF350nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF350nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.350nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500M (Milled) | Glassflake Ltd | ECR Glass Flake GF500M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF500M (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500M (Unmilled) | Glassflake Ltd | ECR Glass Flake GF500 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier p...展開 ECR Glass Flake GF500 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 3.5 - 5.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF500nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF500nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF500nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF500nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF500nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.500nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750M (Milled) | Glassflake Ltd | ECR Glass Flake GF750 (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF750 (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750M (Unmilled) | Glassflake Ltd | ECR Glass Flake GF750 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier p...展開 ECR Glass Flake GF750 (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of 5.5 - 9.5μm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750nm (Unmilled) | Glassflake Ltd | ECR Glass Flake GF750nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pr...展開 ECR Glass Flake GF750nm (Unmilled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| ECR Glass Flake GF750nmM (Milled) | Glassflake Ltd | ECR Glass Flake GF750nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier pro...展開 ECR Glass Flake GF750nmM (Milled) is an extra corrosion resistant glass flake which is manufactured from modified C glass with a nominal thickness of ca.750nm. Primarily used in anti-corrosive coatings, glass flakes can be used to improve both barrier properties and reinforcement of mechanical properties, giving the finished product an isotropic reinforcement across the plane of the platelet. Glassflake materials are offered with the option of surface pre-treatment with a range of saline coupling agents including; 3-Aminopropyltriethoxy Saline, Vinyl trimethoxy Saline, γ-Glycidoxypropyltrimethoxy Saline and Methacryloxypropyltrimethoxy Saline. 收起 | |
| EVACOTE® 7089A | The International Group, Inc. (IGI Wax) | EVACOTE® 7089A is a specialty formulation of petroleum waxes and polymers suitable in consistency to be utilized as a sealant and coating for fertilizer applications. | |
| EVACOTE® 7292C | The International Group, Inc. (IGI Wax) | EVACOTE® 7292C is a premium multi-component formulation having good barrier properties against both water and moisture vapor. Its low viscosity might assist in achieving better machinability for application. | |
| Fast Blue B | Emperor Pigment Co., Ltd. | Fast Blue B is a pigment that is reddish in color. It has a color index number of Pigment Blue 15, a CAS number of 147-14-8, and an EU number of 205-685-1. This product has a density value of 1.5, a pH value of 7, and is used in offset inks, aqueous inks,...展開 Fast Blue B is a pigment that is reddish in color. It has a color index number of Pigment Blue 15, a CAS number of 147-14-8, and an EU number of 205-685-1. This product has a density value of 1.5, a pH value of 7, and is used in offset inks, aqueous inks, and paints. 收起 | |
| Fast Blue BGNCF | Emperor Pigment Co., Ltd. | Fast Blue BGNCF is a greenish colored pigment that is used in inks. It has a density value of 1.5 and a pH value of 7. This product has a color index number of Pigment Blue 15:4, a CAS number of 147-14-8, and an EU number of 205-685-1. | |
| Fast Blue BGS | Emperor Pigment Co., Ltd. | Fast Blue BGS is a pigment that is greenish in color. It has a color index number of Pigment Blue 15:3, a CAS number of 122390-87-1, and an EU number of 205-685-1. This product has a density value of 1.5, a pH value of 7, and is used in offset inks. | |
| Fast Blue BS | Emperor Pigment Co., Ltd. | Fast Blue BS is a reddish colored pigment that is used in paints and inks. It has a color index number of Pigment Blue 15:1, a CAS number of 12239-87-1, and an EU number of 205-685-1. This product has a density value of 1.5 and a pH value of 7. | |
| Fast Blue Lake | Emperor Pigment Co., Ltd. | Fast Blue Lake is a blue colored pigment that is used in offset inks, waterbased inks, solvent based inks, and Toluene based inks. It has a heat value of 100 degrees Celsius and an oil absorption value of 30 maximum. This product has a color index number ...展開 Fast Blue Lake is a blue colored pigment that is used in offset inks, waterbased inks, solvent based inks, and Toluene based inks. It has a heat value of 100 degrees Celsius and an oil absorption value of 30 maximum. This product has a color index number of Pigment Blue 17, and a CAS number of 71799-04-7. 收起 | |
| Fast Blue Lake BO | Emperor Pigment Co., Ltd. | Fast Blue Lake BO is a blue colored pigment that is used in offset inks. It has a color index number of Pigment Blue 1, and a CAS number of 1325-87-7. This product has a heat value of 140 degrees Celsius and an oil absorption value of less than 45. | |
| Fast Blue Toner | Emperor Pigment Co., Ltd. | Fast Blue Toner is a reddish colored pigment that is used in offset inks, aqueous inks, and solvent inks. It has a density value of 1.6 and a pH value of 7. This product has a color index number of Pigment Blue 1, a CAS number of 1325-410-7, and an EU num...展開 Fast Blue Toner is a reddish colored pigment that is used in offset inks, aqueous inks, and solvent inks. It has a density value of 1.6 and a pH value of 7. This product has a color index number of Pigment Blue 1, a CAS number of 1325-410-7, and an EU number of 215-410-7. 收起 | |
| Fast Blue Toner R | Emperor Pigment Co., Ltd. | Fast Blue Toner R is a pigment that is blue in color. It has a color index number of Pigment Blue 10 and a CAS number of 71798-70-4. This product has a density value of 1.8, a pH value of 6, and is used in offset inks, solvent inks, and aqueous inks. | |
| Fast Milori Blue | Emperor Pigment Co., Ltd. | Fast Milori Blue is a pigment that is blue in color. It has a color index number of Pigment Blue 27, and a CAS number of 14038-43-8. This product has a density value of 1.7 to 1.8, a pH value of 6.0 to 8.0, and is used in offset inks, solvent based paints...展開 Fast Milori Blue is a pigment that is blue in color. It has a color index number of Pigment Blue 27, and a CAS number of 14038-43-8. This product has a density value of 1.7 to 1.8, a pH value of 6.0 to 8.0, and is used in offset inks, solvent based paints, and waterbased paints. 收起 | |
| Fast Orange G | Emperor Pigment Co., Ltd. | Fast Orange G is a pigment that is yellowish transparent in color. It has a color index number of Pigment Orange 13, a CAS number of 3520-72-7, and an EU number of 222-530-3. This product has a density value of 1.5, a pH value of 7, and is used in solvent...展開 Fast Orange G is a pigment that is yellowish transparent in color. It has a color index number of Pigment Orange 13, a CAS number of 3520-72-7, and an EU number of 222-530-3. This product has a density value of 1.5, a pH value of 7, and is used in solvent inks. 收起 | |
| Fast Orange G-R | Emperor Pigment Co., Ltd. | Fast Orange G-R is an orange colored pigment that is used in surface printing inks. It has a color index number of Pigment Orange 13, and a heat resistance value of 160 degrees Celsius. | |
| Fast Orange GRN (Semi-Tr) | Emperor Pigment Co., Ltd. | Fast Orange GRN (Semi-Tr) is a pigment that is orange in color. It has a color index number of Pigment Orange 16, a heat resistance value of 180 degrees Celsius, and is used in offset inks and waterbased inks. | |
| Fast Orange GRN-P(Tr)16 | Emperor Pigment Co., Ltd. | Fast Orange GRN-P(Tr)16 is an orange colored pigment that is used in surface printing inks and inner printing inks. It has a heat resistance value of 180 degrees Celsius and a color index number of Pigment Orange 16. | |
| Fast Orange OP-213(OP) | Emperor Pigment Co., Ltd. | Fast Orange OP-213(OP) is a pigment that is orange in color. It has a color index number of Pigment Orange 34, and a CAS number of 15793-73-4. This product has a density value of 1.40 to 1.45, a pH value of 6.0 to 8.0, and is used in waterbased inks and o...展開 Fast Orange OP-213(OP) is a pigment that is orange in color. It has a color index number of Pigment Orange 34, and a CAS number of 15793-73-4. This product has a density value of 1.40 to 1.45, a pH value of 6.0 to 8.0, and is used in waterbased inks and oil based ink. 收起 | |
| Fast Orange RL-TR | Emperor Pigment Co., Ltd. | Fast Orange RL-TR is a pigment that is reddish in color. It has a color index number of Pigment Orange 34, a CAS number of 15793-72-4, and an EU number of 239-898-6. This product has a density value of 1.4, a pH value of 6.5, and is used in aqueous inks a...展開 Fast Orange RL-TR is a pigment that is reddish in color. It has a color index number of Pigment Orange 34, a CAS number of 15793-72-4, and an EU number of 239-898-6. This product has a density value of 1.4, a pH value of 6.5, and is used in aqueous inks and aqueous coatings. 收起 | |
| Fast Orange RL-T(Tr) | Emperor Pigment Co., Ltd. | Fast Orange RL-T(Tr) is a pigment that is reddish in color. It has a color index number of Pigment Orange 34, a CAS number of 15793-72-4, and an EU number of 239-898-6. This product has a density value of 1.4, a pH value of 6,5, and is used in solvent ink...展開 Fast Orange RL-T(Tr) is a pigment that is reddish in color. It has a color index number of Pigment Orange 34, a CAS number of 15793-72-4, and an EU number of 239-898-6. This product has a density value of 1.4, a pH value of 6,5, and is used in solvent inks, aqueous inks, and aqueous coatings. 收起 | |
| Fast Orange RL(Semi-Tr) | Emperor Pigment Co., Ltd. | Fast Orange RL(Semi-Tr) is an orange colored pigment that is used in waterbased inks. It has a color index number of Pigment Orange 34, a density value of 1.6, and a pH value of 6.0 to 7.0. | |
| Fast Orange RN | Emperor Pigment Co., Ltd. | Fast Orange RN is an orange colored pigment that is used in aqueous inks and air drying paints. It has a color index number of Pigment Orange 5, a CAS number of 3468-63-1, and an EU number of 222-429-4. This product has a density value of 1.4 and a pH val...展開 Fast Orange RN is an orange colored pigment that is used in aqueous inks and air drying paints. It has a color index number of Pigment Orange 5, a CAS number of 3468-63-1, and an EU number of 222-429-4. This product has a density value of 1.4 and a pH value of 5.5. 收起 | |
| Fast Red BBC-S | Emperor Pigment Co., Ltd. | Fast Red BBC-S is a pigment that is bluish red in color. It has a color index number of Pigment Red 48:2, a CAS number of 7023-61-2, and an EU number of 230-303-5. This product has a density value of 1.8, a pH value of 7.0 to 8.0, and is used in NC inks, ...展開 Fast Red BBC-S is a pigment that is bluish red in color. It has a color index number of Pigment Red 48:2, a CAS number of 7023-61-2, and an EU number of 230-303-5. This product has a density value of 1.8, a pH value of 7.0 to 8.0, and is used in NC inks, PA inks, and PP inks. 收起 | |
| Fast Red BBN | Emperor Pigment Co., Ltd. | Fast Red BBN is a yellowish red colored pigment that is used in offset inks. It has a density value of 1.8 and a pH value of 7.0 to 8.0. This product has a color index number of Pigment Red 48:1, a CAS number of 7585-41-3, and an EU number of 231-494-8. | |
| Fast Red BBN-W | Emperor Pigment Co., Ltd. | Fast Red BBN-W is a pigment that is yellowish red in color. It has a color index number of Pigment Red 48:1, a CAS number of 7858-41-3, and an EU number of 231-494-8. This product has a density value of 1.8, a pH value of 7.0 to 8.0, and is used in waterb...展開 Fast Red BBN-W is a pigment that is yellowish red in color. It has a color index number of Pigment Red 48:1, a CAS number of 7858-41-3, and an EU number of 231-494-8. This product has a density value of 1.8, a pH value of 7.0 to 8.0, and is used in waterbased inks and in offset inks. 收起 | |
| Fast Red BBS-W | Emperor Pigment Co., Ltd. | Fast Red BBS-W is a pigment that is red in color. It has a color index number of Pigment Red 48:3, a CAS number of 15782-05-5, and an EU number of 239-879-2. This product has a density value of 1.8, a pH value of 7.0 to 8.0, and is used in waterbased inks...展開 Fast Red BBS-W is a pigment that is red in color. It has a color index number of Pigment Red 48:3, a CAS number of 15782-05-5, and an EU number of 239-879-2. This product has a density value of 1.8, a pH value of 7.0 to 8.0, and is used in waterbased inks. 收起 | |
| Fast Red F2R | Emperor Pigment Co., Ltd. | Fast Red F2R is a yellowish red colored pigment that is used in waterbased inks and in textile printing. It has a color index number of Pigment Red 2, a CAS number of 6041-94-7, and an EU number of 227-930-1. This product has a density value of 1.5 and a ...展開 Fast Red F2R is a yellowish red colored pigment that is used in waterbased inks and in textile printing. It has a color index number of Pigment Red 2, a CAS number of 6041-94-7, and an EU number of 227-930-1. This product has a density value of 1.5 and a pH value of 6.5 to 7.5. 收起 | |
| Fast Red F4R | Emperor Pigment Co., Ltd. | Fast Red F4R is a bluish red colored pigment that is used in textile printing and waterbased inks. It has a density value of 1.5 and a pH value of 6.5 to 7.5. This product has a color index number of Pigment Red 8, a CAS number of 6410-60-6, and an EU num...展開 Fast Red F4R is a bluish red colored pigment that is used in textile printing and waterbased inks. It has a density value of 1.5 and a pH value of 6.5 to 7.5. This product has a color index number of Pigment Red 8, a CAS number of 6410-60-6, and an EU number of 229-100-4. 收起 | |
| Fast Red N | Emperor Pigment Co., Ltd. | Fast Red N is a pigment that is yellowish red in color. It has a color index number of Pigment Red 22, a CAS number of 6448-95-9, and an EU number of 229-245-3. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used in waterbased i...展開 Fast Red N is a pigment that is yellowish red in color. It has a color index number of Pigment Red 22, a CAS number of 6448-95-9, and an EU number of 229-245-3. This product has a density value of 1.5, a pH value of 6.0 to 7.0, and is used in waterbased inks. 收起 | |
| Fast Red Toner 6BMW | Emperor Pigment Co., Ltd. | Fast Red Toner 6BMW is a pigment that is violet in color. It has a color index number of Pigment Violet 2, a CAS number of 1326-04-1, and an EU number of 215-414-9. This product has a density value of 1.8, a pH value of 6, and is used in aqueous inks and ...展開 Fast Red Toner 6BMW is a pigment that is violet in color. It has a color index number of Pigment Violet 2, a CAS number of 1326-04-1, and an EU number of 215-414-9. This product has a density value of 1.8, a pH value of 6, and is used in aqueous inks and coating. 收起 | |
| Fast Rose Lake | Emperor Pigment Co., Ltd. | Fast Rose Lake is a violet colored pigment that is used in aqueous inks. It has a density value of 1.7 and a pH value of 7. This product has a color index number of Pigment Violet 1, a CAS number of 1326-03-0, and an EU number of 215-413-3. | |
| Fast Rose Toner | Emperor Pigment Co., Ltd. | Fast Rose Toner is a violet colored pigment that is used in offset inks and aqueous inks. It has a density value of 1.7 and a pH value of 7. This product has a color index number of Pigment Violet 1, a CAS number of 1326-03-0, and an EU number of 215-413-...展開 Fast Rose Toner is a violet colored pigment that is used in offset inks and aqueous inks. It has a density value of 1.7 and a pH value of 7. This product has a color index number of Pigment Violet 1, a CAS number of 1326-03-0, and an EU number of 215-413-3. 收起 | |
| Fast Rose Toner 6BMW | Emperor Pigment Co., Ltd. | Fast Rose Toner 6BMW is a pigment that is violet in color. It has a color index number of Pigment Violet 2, a CAS number of 1326-04-1, and an EU number of 215-414-9. This product has a density value of 1.8, a pH value of 6, and is used in aqueous inks and...展開 Fast Rose Toner 6BMW is a pigment that is violet in color. It has a color index number of Pigment Violet 2, a CAS number of 1326-04-1, and an EU number of 215-414-9. This product has a density value of 1.8, a pH value of 6, and is used in aqueous inks and aqueous coatings. 收起 | |
| Fast Violet 4R | Emperor Pigment Co., Ltd. | Fast Violet 4R is a pigment that is violet in color. It has a color index number of Pigment Violet 19, and a CAS number of 1047-16-1. This product has a density value of 1.5, a pH value of 6.8, and is used in coloring printing inks, paints, and pigment pr...展開 Fast Violet 4R is a pigment that is violet in color. It has a color index number of Pigment Violet 19, and a CAS number of 1047-16-1. This product has a density value of 1.5, a pH value of 6.8, and is used in coloring printing inks, paints, and pigment printing. 收起 | |
| Fast Violet Lake | Emperor Pigment Co., Ltd. | Fast Violet Lake is a reddish colored pigment that is used in offset inks, aqueous inks, and solvent inks. It has a color index number of Pigment Violet 3, a CAS number of 1325-82-2, and an EU number of 273-548-3. This product has a density value of 1.8 a...展開 Fast Violet Lake is a reddish colored pigment that is used in offset inks, aqueous inks, and solvent inks. It has a color index number of Pigment Violet 3, a CAS number of 1325-82-2, and an EU number of 273-548-3. This product has a density value of 1.8 and a pH value of 6. 收起 | |
| Fast Violet Toner R | Emperor Pigment Co., Ltd. | Fast Violet Toner R is a bluish colored pigment that is used in offset inks and aqueous inks. It has a color index number of Pigment Violet 3, a CAS number of 1325-82-2, and an EU number of 273-548-3. This product has a density value of 1.8 and a pH value...展開 Fast Violet Toner R is a bluish colored pigment that is used in offset inks and aqueous inks. It has a color index number of Pigment Violet 3, a CAS number of 1325-82-2, and an EU number of 273-548-3. This product has a density value of 1.8 and a pH value of 6. 收起 | |
| Fast Yellow 10G | Emperor Pigment Co., Ltd. | Fast Yellow 10G is a greenish yellow colored pigment that is used in air drying paints, offset inks, industrial paints, and in waterbased coatings. It has a density value of 1.6 and a pH value of 6.0 to 7.0. This product has a color index number of Pigmen...展開 Fast Yellow 10G is a greenish yellow colored pigment that is used in air drying paints, offset inks, industrial paints, and in waterbased coatings. It has a density value of 1.6 and a pH value of 6.0 to 7.0. This product has a color index number of Pigment Yellow 3, a CAS number of 6486-23-2, and an EU number of 229-355-1. 收起 | |
| Fast Yellow G | Emperor Pigment Co., Ltd. | Fast Yellow G is a pigment that is bright yellow in color. It has a color index number of Pigment Yellow 1, a CAS number of 2512-29-0, and an EU number of 219-730-8. This product has a density value of 1.6, a pH value of 6.0 to 7.0, and is used in air dry...展開 Fast Yellow G is a pigment that is bright yellow in color. It has a color index number of Pigment Yellow 1, a CAS number of 2512-29-0, and an EU number of 219-730-8. This product has a density value of 1.6, a pH value of 6.0 to 7.0, and is used in air drying paints, offset inks, industrial paints, and in waterbased coatings. 收起 | |
| Hanos ASP-100F | Hanwha Chemical Corporation | Hanos ASP-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechan...展開 Hanos ASP-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechanical strength. This product is well suited for use in conductive transparent electrodes, conductive nano ink, conductive heating films, nano device, nano-bio material and chemical sensors. 收起 | |
| Hanos AST-100F | Hanwha Chemical Corporation | Hanos AST-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechan...展開 Hanos AST-100F is a single-walled carbon nano tube produced by conventional arc-discharge process using Fe-based metal catalysts. It has good electric conductivity and heat conductivity with a high crystallinity and aspect ratio giving it excellent mechanical strength. This product is well suited for use in conductive transparent electrodes, conductive nano ink, conductive heating films, nano device, nano-bio material and chemical sensors. 收起 | |
| Hanos MWCNT CM-150 | Hanwha Chemical Corporation | Hanos MWCNT CM-150 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-150 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-150 Composite material is well suited for the production of ESD, EMI shielding, reinforced material, heat exchangers, etc. 收起 | |
| Hanos MWCNT CM-250 | Hanwha Chemical Corporation | Hanos MWCNT CM-250 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-250 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-250 Composite material is well suited for the production of for inks & paste, ESD, EMI Shielding, reinforced materials, heat exchanger, etc. 收起 | |
| Hanos MWCNT CM-280 | Hanwha Chemical Corporation | Hanos MWCNT CM-280 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-280 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 95 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-280 Composite material is well suited for the production of for inks & paste, ESD, EMI Shielding, reinforced materials, heat exchanger, etc. 收起 | |
| Hanos MWCNT CM-350 | Hanwha Chemical Corporation | Hanos MWCNT CM-350 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitab...展開 Hanos MWCNT CM-350 is a multi-walled carbon nano tube synthesized by catalytic CVD process. It has about 90 wt.% purity without any purification. By virtue of improvements in the synthetic process, it shows enhanced conductivity and dispersibility suitable for conductive composite application. CM-350 Composite material is well suited for the production of for inks & paste, ESD, EMI Shielding, reinforced materials, heat exchanger, etc. 收起 | |
| Hanos PS Compound / Sheet | Hanwha Chemical Corporation | Hanos PS Compound / Sheet is a conductive product for Electrostatic Dissipative(ESD) or antistatic purpose with special CNT layers. It can be used in various industrial areas to prevent electrical damages of target products. It is well suited for use as a...展開 Hanos PS Compound / Sheet is a conductive product for Electrostatic Dissipative(ESD) or antistatic purpose with special CNT layers. It can be used in various industrial areas to prevent electrical damages of target products. It is well suited for use as a filler in the production of sheets or as a black pigment in inks and paints. 收起 | |
| Hanos PS Ink | Hanwha Chemical Corporation | Hanos PS Ink is a PP pellet coating ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applicati...展開 Hanos PS Ink is a PP pellet coating ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications such as conductive films or inks for chip trays. 收起 | |
| Hanos SW01 | Hanwha Chemical Corporation | Hanos SW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications ...展開 Hanos SW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications such as conductive films or inks for chip trays. 收起 | |
| Hanos TW01 | Hanwha Chemical Corporation | Hanos TW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications ...展開 Hanos TW01 is a water-based CNT ink that has excellent surface resistance on film. Eco-friendly, it can impart electrostatic resistance, thermal and added strength to many products. It is well suited for use as a filler in various industrial applications such as conductive films or inks for chip trays. 收起 | |
| Hanwha 2-EH (2-Ethyl-1-Hexanol) | Hanwha Chemical Corporation | Hanwha 2-EH is an colorless, transparent liquid made of 2-Ethyl-1-Hexanol. It is primarily used as the main ingredient in the production of certain types of plasticizers. It is well suited for use in making solvents, stabilizers and acrylates as well. | |
| Hanwha CP-430 | Hanwha Chemical Corporation | Hanwha CP-430 is a Vinyl Chloride-Vinyl Acetate Copolymer with outstanding solvent solubility, adhesion, transparency and liquidity. CP-430 is well suited for use in the production of Gravure inks, adhesives and paints. | |
| Hanwha CP-450 | Hanwha Chemical Corporation | Hanwha CP-450 is a Vinyl Chloride-Vinyl Acetate Copolymer with outstanding solvent solubility, adhesion, transparency and liquidity. CP-450 is well suited for use in the production of inks, adhesives and paints. | |
| Hanwha CP-710 | Hanwha Chemical Corporation | Hanwha CP-710 is a Vinyl Chloride-Vinyl Acetate Copolymer with outstanding solvent solubility, adhesion, transparency and liquidity. CP-710 is well suited for use in the production of inks, adhesives and paints. | |
| Hanwha DIDP (Diisodecyl Phthalate) | Hanwha Chemical Corporation | Hanwha DIDP is a transparent plasticizer made of Diisononyl Phthalate with excellent viscosity and outstanding electrical insulation. It is well suited for use in the production of films, sheets, leathers, wire coatings, wall papers and flooring materials...展開 Hanwha DIDP is a transparent plasticizer made of Diisononyl Phthalate with excellent viscosity and outstanding electrical insulation. It is well suited for use in the production of films, sheets, leathers, wire coatings, wall papers and flooring materials where ever cold, light and chemicals resistance is required. 收起 |
