| 205 | U.S. Zinc | 205 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, paint/coating, ceramics industries, rubber, and in those applications where reasonable purity is required. 205 is a...voir plus 205 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, paint/coating, ceramics industries, rubber, and in those applications where reasonable purity is required. 205 is available in a pelleted form (205P) and with surface treatment (205S). It has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| 205H | U.S. Zinc | 205H is a small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the paint, latex, plastic, and zinc chemicals industries and in applications where moderate...voir plus 205H is a small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the paint, latex, plastic, and zinc chemicals industries and in applications where moderate purity and greater reactivity are required. Grade 205H is available in a pelleted form (205HS) and with surface treatment (205HS). 205H has a surface area range of 6.0 to 8.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| 205HSA | U.S. Zinc | 205HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the plastic, latex, and transparent rubber industries and in those applica...voir plus 205HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a greater surface area and is used by the plastic, latex, and transparent rubber industries and in those applications where great reactivity is required. 205HSA is obtainable with surface treatment (205HSA-S). It has a surface area range of 8.0 to 10.0 m2 /g, a specific gravity of 5.6, and an apparent density of 20 to 40 (pounds/ft3). voir moins | |
| 205L | U.S. Zinc | 205L is a large particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a lower surface area and is used by the paint and ceramics industries and in those applications where benefits result from larger...voir plus 205L is a large particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. It has a lower surface area and is used by the paint and ceramics industries and in those applications where benefits result from larger than average particles. Grade 205L is available in a pelleted form (205LP) and with surface treatment (205LS). 205L has a surface area range of 3.0 to 5.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| 205XL | U.S. Zinc | 205XL is a large particle size French Process in powder form, statistically measured zinc oxide. 205XL is used by the electronics, coating, ceramics, and paint industries and in those applications which develop benefits from larger than average particles....voir plus 205XL is a large particle size French Process in powder form, statistically measured zinc oxide. 205XL is used by the electronics, coating, ceramics, and paint industries and in those applications which develop benefits from larger than average particles. It has a surface area range of 2.5 to 3.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 15 to 30. voir moins | |
| 210 | U.S. Zinc | 210 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, rubber, tape/adhesives, oil additives, traffic paint, wire insulation, glass/ceramics, electrogalvanizing, brake li...voir plus 210 is a French Process in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemicals, rubber, tape/adhesives, oil additives, traffic paint, wire insulation, glass/ceramics, electrogalvanizing, brake lining, and agriculture industries and in applications where General purpose zinc oxide could be used. 210 is available in a pelleted form (210P) and with surface treatment (210S). It has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| 210E | U.S. Zinc | 210E is common purpose French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used in an assortment of applications, including electronics, brake lining, paint, zinc chemicals, coating, and rubber industrie...voir plus 210E is common purpose French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade is used in an assortment of applications, including electronics, brake lining, paint, zinc chemicals, coating, and rubber industries. 210E is available in pelleted form (210E-P) and with surface treatment (210ES). It has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| 210H | U.S. Zinc | 210H is a small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the latex, paint, plastic, and zinc chemicals industries. 210H is availab...voir plus 210H is a small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the latex, paint, plastic, and zinc chemicals industries. 210H is available in a pelleted form (210HP) and with surface treatment (210HS). It has a surface area range of 6.0 to 8.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| 210HSA | U.S. Zinc | 210HSA is an exceptionally small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the plastic, latex, and transparent rubber industries an...voir plus 210HSA is an exceptionally small particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a higher surface area and reactivity and is used by the plastic, latex, and transparent rubber industries and in applications where high reactivity is required. 210HSA is available with surface treatment (210HSA-S). It has a surface area range of 8 to 10 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40. voir moins | |
| 210L | U.S. Zinc | 210L is a large particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a lower surface area and is used by the ceramics and paint industries. 210L is available in a pelleted form (210LP) and with ...voir plus 210L is a large particle French Process, in powder form, statistically measured zinc oxide formed from zinc metal. This grade has a lower surface area and is used by the ceramics and paint industries. 210L is available in a pelleted form (210LP) and with surface treatment (210LS). It has a surface area range of 3.0 to 5.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| A-6165 | Designer Molecules | A-6165 is a dark brown viscous liquid, additive with a conductive adhesive formulation. This is most commonly used as an additive in combination with metal fillers to further decrease volume resistivity in electrically conductive adhesive applications. | |
| A-675-100% | Designer Molecules | A-675-100% is a Bis(Glyceryl Dimethacrylate) Pyromellitate liquid additive. This product is most commonly used as an additive in adhesive applications. The four methacrylate groups and two carboxylic groups per molecule allow bonding to a variety surfaces...voir plus A-675-100% is a Bis(Glyceryl Dimethacrylate) Pyromellitate liquid additive. This product is most commonly used as an additive in adhesive applications. The four methacrylate groups and two carboxylic groups per molecule allow bonding to a variety surfaces. voir moins | |
| Agrol® 2.0 | BioBased Technologies | Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 2.0 - 4.0 contains 99% bio-based content (ASTM...voir plus Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 2.0 - 4.0 contains 99% bio-based content (ASTM D6866). voir moins | |
| Agrol® 3.0 AO | BioBased Technologies | Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 3.0 AO contains 97% bio-based content (ASTM D6...voir plus Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 3.0 AO contains 97% bio-based content (ASTM D6866). voir moins | |
| Agrol® 3.6 | BioBased Technologies | Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 2.0 - 4.0 contains 99% bio-based content (ASTM...voir plus Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 2.0 - 4.0 contains 99% bio-based content (ASTM D6866). voir moins | |
| Agrol® 4.0 | BioBased Technologies | Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 2.0 - 4.0 contains 99% bio-based content (ASTM...voir plus Agrol® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Products. Agrol® 2.0 - 4.0 contains 99% bio-based content (ASTM D6866). voir moins | |
| Agrol Diamond® | BioBased Technologies | Agrol Diamond® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Diamond® contains 86% bio-based content (...voir plus Agrol Diamond® is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Diamond® contains 86% bio-based content (ASTM D6866) and 70% primary hydroxyl groups. voir moins | |
| Agrol Platinum™ | BioBased Technologies | Agrol Platinum™ is a liquid-mannich polyols derived from a highly reactive cashew nutshell liquid, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Platinum™ conta...voir plus Agrol Platinum™ is a liquid-mannich polyols derived from a highly reactive cashew nutshell liquid, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Platinum™ contains 80.8% bio-based content (ASTM D6866) and Three functional primary hydroxyl groups containing polyol. voir moins | |
| Agrol Prime™ A-110 | BioBased Technologies | Agrol Prime™ is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Prime™ A-110 contains 1,000 molecular weigh...voir plus Agrol Prime™ is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Prime™ A-110 contains 1,000 molecular weight polyol and 67% primary hydroxyl groups. voir moins | |
| Agrol Prime™ A-56 | BioBased Technologies | Agrol Prime™ is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Prime™ A-56 contains 2,000 molecular weight...voir plus Agrol Prime™ is a soy-based polyols derived from purified soybean oil, and is suitable for all polyurethane applications. Made from an annually renewable feedstock, it is a USDA Certified Biobased Product. Agrol Prime™ A-56 contains 2,000 molecular weight polyol and 67% primary hydroxyl groups. voir moins | |
| AZO66 | U.S. Zinc | AZO66 is an exceptionally pure French Process, in powder form, statistically measured zinc oxide formed from zinc metal. AZO66 provides greater color and is vastly efficient in white or light colored goods. This grade is used in the zinc chemical, paint/c...voir plus AZO66 is an exceptionally pure French Process, in powder form, statistically measured zinc oxide formed from zinc metal. AZO66 provides greater color and is vastly efficient in white or light colored goods. This grade is used in the zinc chemical, paint/coating, ceramic, oil additive industries and in those applications where great purity is dire. Grade AZO66 is available in a pelleted form (AZO66P), in a treated pelleted form (AZO66PT), and with surface treatment (AZO66T). AZO66 has a surface area range of 4.0 to 6.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| AZO66L | U.S. Zinc | AZO66L is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemical, paint, and coating industries and in those applications which stem from greater than norma...voir plus AZO66L is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the zinc chemical, paint, and coating industries and in those applications which stem from greater than normal high purity particles. Grade AZO66L is available in a pelleted form (AZO66LP) and with the surface treatment (AZO66LT). AZO66L has a surface area range of 3.0 to 5.0 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 50 to 85. voir moins | |
| AZO66XL | U.S. Zinc | AZO66XL is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the electronic, ceramic, paint, and coating industries and in those applications which stem from greater tha...voir plus AZO66XL is an exceptionally pure French Process, a large particle, statistically measured zinc oxide formed from zinc metal. This grade is used by the electronic, ceramic, paint, and coating industries and in those applications which stem from greater than normal high purity particles. AZO66XL has a surface area range of 2.5 to 3.5 m2 /g, a specific gravity of 5.6, and an apparent density (in powder form) of 20 to 40 and (in pellet form) of 15 to 30. voir moins | |
| AZO77H | U.S. Zinc | AZO77H is an exceptionally pure powder, small particle size French Process, statistically measured zinc oxide formed from zinc metal. It is used for the manufacture of various chemicals, in the plastic, paint, latex, and coating industries and in those ap...voir plus AZO77H is an exceptionally pure powder, small particle size French Process, statistically measured zinc oxide formed from zinc metal. It is used for the manufacture of various chemicals, in the plastic, paint, latex, and coating industries and in those applications where high purity and reactivity is required. Grade AZO77H is available with surface treatment (AZO77HT). It has a surface area range of 6.0 to 8.5 m2 /g, a specific gravity of 5.6, and an apparent density of 20 to 40 (lbs. /cu. Ft.). voir moins | |
| AZO77HSA | U.S. Zinc | AZO77HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. AZO77HSA was explicitly developed to have the highest viscosity, reactivity, purity, and fineness. This grade is used...voir plus AZO77HSA is an exceptionally small particle size French Process in powder form, statistically measured zinc oxide formed from zinc metal. AZO77HSA was explicitly developed to have the highest viscosity, reactivity, purity, and fineness. This grade is used in can sealants, latex compounds, zinc chemicals, plastics, paint/coating, and in the food can liner coating industry where the particularly fine particles freely convert certain accessible soluble into white sulfide, thus avoiding discoloration of food from sulfides of tin or iron. AZO77HSA is available with surface treatment (AZO77HSA-T), has a surface area range of 8.0 to 10.0 m2 /g, a specific gravity of 5.6, and an apparent density of 20 to 40 (lbs. /cu. Ft.). voir moins | |
| BLACK PEARLS® 4040 | Cabot Corporation - Additives | BLACK PEARLS® 4040 is a specialty carbon black for long-term ultraviolet and weatherability protection, good surface smoothness and dispersion performance. This product is well suited for use in a range of film and sheet applications, such as mulch and si...voir plus BLACK PEARLS® 4040 is a specialty carbon black for long-term ultraviolet and weatherability protection, good surface smoothness and dispersion performance. This product is well suited for use in a range of film and sheet applications, such as mulch and silage film, irrigation pipe and tape, and general purpose film and sheet. voir moins | |
| BMI-1500 | Designer Molecules | BMI-1500 is a viscous amber liquid form bismaleimide oligomer. This product exhibits good adhesion to a variety of substrates. BMI-1500 is most commonly used in adhesives as an additive or base resin, for high temperature applications. | |
| BMI-1700 | Designer Molecules | BMI-1700 is a viscous amber liquid form bismaleimide oligomer. This product exhibits good adhesion to a variety of substrates. BMI-1700 is most commonly used in adhesives as an additive or base resin, for high temperature applications. | |
| BMI-3000 | Designer Molecules | BMI-3000 is a light yellow powder form bismaleimide oligomer. This product exhibits excellent flexibility and forms very tough, hydrophobic polyimides. BMI-3000 is most commonly used in adhesives as an additive to increase flexibility, hydrophobicity, and...voir plus BMI-3000 is a light yellow powder form bismaleimide oligomer. This product exhibits excellent flexibility and forms very tough, hydrophobic polyimides. BMI-3000 is most commonly used in adhesives as an additive to increase flexibility, hydrophobicity, and thixotropy. voir moins | |
| BMI-3000 GEL | Designer Molecules | BMI-3000 GEL is a red amber gel form bismaleimide oligomer. This product exhibits excellent flexibility and forms very tough, hydrophobic polyimides. BMI-3000 GEL is most commonly used in adhesives as an additive to increase flexibility, hydrophobicity, a...voir plus BMI-3000 GEL is a red amber gel form bismaleimide oligomer. This product exhibits excellent flexibility and forms very tough, hydrophobic polyimides. BMI-3000 GEL is most commonly used in adhesives as an additive to increase flexibility, hydrophobicity, and thixotropy. voir moins | |
| BMI-5000 | Designer Molecules | BMI-5000 is a light yellow powder form bismaleimide oligomer. This product can be processed in a resin system as a solid or dissolved in a solvent. BMI-5000 is a most commonly used in base resin applications. | |
| BMI-5000 50% Toluene | Designer Molecules | BMI-5000 50% Toluene is a dark brown liquid form bismaleimide oligomer. This product can be processed in a resin system as a solid or dissolved in a solvent. BMI-5000 50% Toluene is a most commonly used in base resin applications. | |
| CAB-O-SIL® EH5 | Cabot Corporation - Additives | CAB-O-SIL® EH5 is a very high surface fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and ...voir plus CAB-O-SIL® EH5 is a very high surface fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and hyprophilic surface chemistry. This product is well suited for use in adhesives and sealants, coatings, and printing inks. voir moins | |
| CAB-O-SIL® H5 | Cabot Corporation - Additives | CAB-O-SIL® H5 is a high surface area fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and h...voir plus CAB-O-SIL® H5 is a high surface area fumed silica that can be used to provide thickening, thixotropic, and anti-settling behavior in liquid systems. It is characterized by high purity, aggregated structure, submicron particle size, low bulk density, and hyprophilic surface chemistry. It is also used for building viscosity in non-polar to medium polarity systems. This product is well suited for use in adhesives, coatings, composites, cosmetics, food, pharmaceuticals, powder coatings, sealants, and silicone rubber systems. voir moins | |
| CAB-O-SIL® LM150 | Cabot Corporation - Additives | CAB-O-SIL® LM150 is a low surface area fumed silica that imparts a moderate increase in viscosity, and reinforcement in liquid and polymer systems. It provides balance of dispersability, thixotropy, and reinforcement. This product is well suited for use f...voir plus CAB-O-SIL® LM150 is a low surface area fumed silica that imparts a moderate increase in viscosity, and reinforcement in liquid and polymer systems. It provides balance of dispersability, thixotropy, and reinforcement. This product is well suited for use for thixotropy in silicone sealants and for reinforcement in silicone rubbers. voir moins | |
| CAB-O-SIL® M-5 | Cabot Corporation - Additives | CAB-O-SIL® M-5 is a untreated medium surface fumed silica that provides thickening, thixotrophic, and anti-settling behavior in liquid systems. It is most efficient in non-polar to medium polarity systems, and provides increases in hardness, tensile stren...voir plus CAB-O-SIL® M-5 is a untreated medium surface fumed silica that provides thickening, thixotrophic, and anti-settling behavior in liquid systems. It is most efficient in non-polar to medium polarity systems, and provides increases in hardness, tensile strength and elongation. It can be used for reinforcement of silicone and organic rubbers. This product is well suited for use in coatings, adhesives, and other liquid systems. voir moins | |
| CAB-O-SIL® TS530 | Cabot Corporation - Additives | CAB-O-SIL® TS530 is a high-purity silica that has been treated with hexamethyldisilazane to render the silica hydrophobic. It offers good rheological control, sag resistance, anti-settling, and improved dispersion. This product is well suited for use in m...voir plus CAB-O-SIL® TS530 is a high-purity silica that has been treated with hexamethyldisilazane to render the silica hydrophobic. It offers good rheological control, sag resistance, anti-settling, and improved dispersion. This product is well suited for use in medium-to-high polarity inks, coatings, and adhesive applications. voir moins | |
| CAB-O-SIL® TS610 | Cabot Corporation - Additives | CAB-O-SIL® TS610 is a low surface area fumed silica that has been surface modified with dimethyldichlorosilane. As a thickener, this product is well suited for use in non-polar to medium polarity inks, coatings, and adhesives. It is also highly effective ...voir plus CAB-O-SIL® TS610 is a low surface area fumed silica that has been surface modified with dimethyldichlorosilane. As a thickener, this product is well suited for use in non-polar to medium polarity inks, coatings, and adhesives. It is also highly effective as free-flow additive for moisture-sensitive powder systems. voir moins | |
| CAB-O-SIL® TS622 | Cabot Corporation - Additives | CAB-O-SIL® TS622 is a medium surface area fumed silica that has been surface modified with dimethyldichlorosilane. This product is specially designed for use as a reinforcing agent for RTV-1 silicone sealants, where it provides faster wet-in or incorporat...voir plus CAB-O-SIL® TS622 is a medium surface area fumed silica that has been surface modified with dimethyldichlorosilane. This product is specially designed for use as a reinforcing agent for RTV-1 silicone sealants, where it provides faster wet-in or incorporation, better dispersion, and good sealant surface smoothness and appearance. voir moins | |
| CAB-O-SIL® TS720 | Cabot Corporation - Additives | CAB-O-SIL® TS720 is a medium surface area fumed silica which has been surface modified with polydimethylsiloxane. It provides thickening efficiency, sag resistance or high film build, anti-settling of pigments and fillers, shear-thinning rheological behav...voir plus CAB-O-SIL® TS720 is a medium surface area fumed silica which has been surface modified with polydimethylsiloxane. It provides thickening efficiency, sag resistance or high film build, anti-settling of pigments and fillers, shear-thinning rheological behavior, and stable rheological performance over time. This product is well suited for rheology control in adhesives, composites, and coatings. voir moins | |
| CAB-O-SPERSE® 1030K | Cabot Corporation - Additives | CAB-O-SPERSE® 1030K is an aqueous fumed silica dispersion featuring low viscosity and high solids loading. Performance benefits of this product include good rheological control,anti-blocking, anti-corrosion, adhesion promotion, and surface treatment prope...voir plus CAB-O-SPERSE® 1030K is an aqueous fumed silica dispersion featuring low viscosity and high solids loading. Performance benefits of this product include good rheological control,anti-blocking, anti-corrosion, adhesion promotion, and surface treatment properties. This product is well suited for use in coatings, adhesives, and metal and optical glass polish applications. voir moins | |
| CS-697 | Designer Molecules | CS-697 is a colorless liquid polyglycidyl ether cyclosiloxane monomer. This product features multifunctional, low viscosity, low epoxy equivalent weight, colorless, thermal stability, non-yellowing (UV exposure), and low chloride. CS-697 is most commonly ...voir plus CS-697 is a colorless liquid polyglycidyl ether cyclosiloxane monomer. This product features multifunctional, low viscosity, low epoxy equivalent weight, colorless, thermal stability, non-yellowing (UV exposure), and low chloride. CS-697 is most commonly used to formulate adhesives in organic resins applications. This resin is very compatible with most organic resins. voir moins | |
| CS-783 | Designer Molecules | CS-783 is a yellow liquid methacrylated epoxy. This product features dual cure mechanisms, low chloride, multifunctional, low viscosity, and UV curable. CS-783 is most commonly used in adhesion promoting applications. | |
| CUMAR® 105 | Neville Chemical Company | CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne ...voir plus CUMAR® 105 is an aromatic flaked resin that promotes wetting of pigments and fillers, improves resistance to acids and alkalis, maintains thermal stability and enables leafing characteristics for metallic pigments. It is used in high solids solvent-borne and epoxy based coatings, IV ink modifiers, adhesives and sealants. voir moins | |
| EC-1074 | Designer Molecules | EC-1074 is an amber glassy solid tetra-phenol epoxy. This product highlights low modulus, hydrophobic, thermal stability, hydrolytically resistant thermosets. EC-1074 is most commonly used as an epoxy curative in film and pre-applied adhesive composition...voir plus EC-1074 is an amber glassy solid tetra-phenol epoxy. This product highlights low modulus, hydrophobic, thermal stability, hydrolytically resistant thermosets. EC-1074 is most commonly used as an epoxy curative in film and pre-applied adhesive composition applications. voir moins | |
| EC-234 | Designer Molecules | EC-234 is a light yellow, liquid phenyl ester epoxy curative hybrid. This product has the ability to cure with both epoxy resin through the phenyl ester or in a free radical resin system through the acrylate. EC-234 is most commonly used as an adhesive o...voir plus EC-234 is a light yellow, liquid phenyl ester epoxy curative hybrid. This product has the ability to cure with both epoxy resin through the phenyl ester or in a free radical resin system through the acrylate. EC-234 is most commonly used as an adhesive or coating in a multitude of applications. voir moins | |
| EC-298 | Designer Molecules | EC-298 is a clear light yellow, liquid difunctional phenyl ester epoxy. This product does not interfere with free-radical cure and is therefore well suited for use in epoxy/(meth)acrylate hybrid thermoset compositions. EC-298 is most commonly used as an e...voir plus EC-298 is a clear light yellow, liquid difunctional phenyl ester epoxy. This product does not interfere with free-radical cure and is therefore well suited for use in epoxy/(meth)acrylate hybrid thermoset compositions. EC-298 is most commonly used as an epoxy curative in applications where toughness is required. voir moins | |
| EC-326 | Designer Molecules | EC-326 is a white to light yellow solid acetate/proprionate epoxy. This product has low melting curative properties, is soluble in most epoxy monomers, and low moisture uptake. EC-326 is most commonly used to improve toughness, hydrophobicity, and hydroly...voir plus EC-326 is a white to light yellow solid acetate/proprionate epoxy. This product has low melting curative properties, is soluble in most epoxy monomers, and low moisture uptake. EC-326 is most commonly used to improve toughness, hydrophobicity, and hydrolytic stability in adhesive applications. voir moins | |
| EC-392 | Designer Molecules | EC-392 is an amber liquid phenyl ester epoxy. This product highlights dual cure mechanism, high cross-link density, and thermal stability. EC-392 is most commonly used in liquid adhesives and paste applications. | |
| EC-861 | Designer Molecules | EC-861 is a yellow liquid phenyl acetate epoxy curative. This product highlights low modulus, hydrophobic, thermal stability, and hydrolytically resistant thermosets. EC-861 is most commonly used in applications where high levels of toughness and flexibil...voir plus EC-861 is a yellow liquid phenyl acetate epoxy curative. This product highlights low modulus, hydrophobic, thermal stability, and hydrolytically resistant thermosets. EC-861 is most commonly used in applications where high levels of toughness and flexibility are needed. voir moins | |
| ECAT-243 | Designer Molecules | ECAT-243 is a yellow microcrystalline solid imidazole epoxy catalyst. This product features good solubility in most epoxy monomers and excellent latency characteristics. ECAT-243 is most commonly used in epoxy homocure and epoxy curative applications. | |
| ECAT-259 | Designer Molecules | ECAT-259 is a yellow powder imidazole epoxy. This product features good solubility in most epoxy monomers, excellent latency characteristics, can be used as a catalyst or curative, and tunable cures. ECAT-259 is most commonly used in catalyst and epoxy c...voir plus ECAT-259 is a yellow powder imidazole epoxy. This product features good solubility in most epoxy monomers, excellent latency characteristics, can be used as a catalyst or curative, and tunable cures. ECAT-259 is most commonly used in catalyst and epoxy curative, applications. voir moins | |
| ECAT-353 | Designer Molecules | ECAT-353 is a besige powder imidazole epoxy catalyst. This product features good solubility in most epoxy monomers, excellent latency characteristics, can be used as a catalyst or curative, and tunable cures. ECAT-353 is most commonly used in catalyst and...voir plus ECAT-353 is a besige powder imidazole epoxy catalyst. This product features good solubility in most epoxy monomers, excellent latency characteristics, can be used as a catalyst or curative, and tunable cures. ECAT-353 is most commonly used in catalyst and epoxy curative applications. voir moins | |
| ECAT-434 | Designer Molecules | ECAT-434 is a yellow solid imidazole epoxy catalyst. This product features good solubility in most epoxy monomers, excellent latency characteristics, can be used as a catalyst or curative, and tunable cures. ECAT-434 is most commonly used in catalyst and ...voir plus ECAT-434 is a yellow solid imidazole epoxy catalyst. This product features good solubility in most epoxy monomers, excellent latency characteristics, can be used as a catalyst or curative, and tunable cures. ECAT-434 is most commonly used in catalyst and epoxy curative applications. voir moins | |
| Flytac 102-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...voir plus Flytac 102-100 is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR. This product has a colour gardener (in 50% Toluene) of 4 max., an acid value of 20mg KOH/g max., and a softening point (R&B) of 97-100℃. voir moins | |
| FLYTAC 103-85 | Guangzhou Flying Dragon Chemical Ltd. | A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS,...voir plus A slight yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol, it has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. voir moins | |
| Flytac 103-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for thi...voir plus Flytac 103-E is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Uses for this product include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It an also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. Flytac 103-E has a softening point (R&B) of 82-90°C min., an acid value of 3-8mg KOH/g max., and a colour gardener (in 50% Toluene) of 8 max. voir moins | |
| Flytac 104 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used...voir plus Flytac 104 is a pale, thermoplastic, acidic resin made by hydrogenating rosin. Due to this treatment, it s highly resistant to oxidation, discoloration, and to changes in solubility characteristics when it is exposed to air and sunlight. It is mainly used as raw material for the manufacture of a number of products including bookbinding, caulking, paint and coatings, personal care and cosmetics, pressure sensitive adhesives, rubber and plastic modification, solvent-borne adhesives, tapes and labels, waterborne adhesives, and wax modification. This product has an abietic acid of 2.0% max., a softening point (R&B) of 76°C min., and a dehydroabietic acid of 8.0% max. voir moins | |
| Flytac 105-L | Guangzhou Flying Dragon Chemical Ltd. | Flytac105-L is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, waterborne adhesives, non-wovens, packaging, tapes and labels, as well as in wax depilatories. In...voir plus Flytac105-L is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, waterborne adhesives, non-wovens, packaging, tapes and labels, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-oxidizing, color-stable, highly tacky liquid resin. Flytac105-L has a softening point (R&B) of 85°C, an acid value of 9mg KOH/g max., and an ash content of 0.2% max. voir moins | |
| Flytac 106-100 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 106-100 is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesiv...voir plus Flytac 106-100 is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesive formulations, it contributes improved resistance to oxidation, greater heat stability, better retention of color, and greater retention of tack-imparting properties than ordinary rosin ester resins. Flytac 106-100 has a color gardener of 8~10, a specific gravity (25°C/25°C) of 1.060~1.090, and a softening point (R&B) of 95-102°C min. voir moins | |
| Flytac 106-100L | Guangzhou Flying Dragon Chemical Ltd. | Flytac 106-100L is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesi...voir plus Flytac 106-100L is a medium hard, pale, thermoplastic resin designed primarily as a tackifying resin for various types of polymer- and elastomer-based adhesives. It is a pentaerythritol ester of a rosin that has been stabilized by hydrogenation. In adhesive formulations, it contributes improved resistance to oxidation, greater heat stability, better retention of color, and greater retention of tack-imparting properties than ordinary rosin ester resins. This product has a color gardener of 4~6, a softening point (R&B) of 95-102°C, and a specific gravity (25°C/25°C) of 1.060~1.090. voir moins | |
| Flytac 107 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 107 is made of derivatives of gum rosin obtained by chemical treatment to reduce the Abietic Acid content. It is used as a tackifier for pressure sensitive adhesive, in the manufacture of SBR and other synthetic rubbers, as well as in important com...voir plus Flytac 107 is made of derivatives of gum rosin obtained by chemical treatment to reduce the Abietic Acid content. It is used as a tackifier for pressure sensitive adhesive, in the manufacture of SBR and other synthetic rubbers, as well as in important component for making potassium soaps. This product has a dehydrated acid content of 52.0% min., an unsaponifiable material of 10.0% max., and an abietic acid of 1% max. voir moins | |
| Flytac 111-101 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 111-101 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly st...voir plus Flytac 111-101 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly stabilized rosins commercially available, and is especially indicated as the tackifier in solvent adhesives and hot-melt applied coatings and adhesives that must excel in these properties. Flytac 111-101 has a tetrahydro resin acid of 10.0% min., an abietic acid of 2.0% max., and a dehydroabietic acid of 10.0% max. voir moins | |
| Flytac 111-301 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 111-301 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly st...voir plus Flytac 111-301 is refined from High-Hydrogenated rosin that is eliminated foreign matter and the coloring radical. It is a thermoplastic, acidic resin produced by hydrogenating rosin to an exceptionally high degree. It is one of the palest, most highly stabilized rosins commercially available, and is especially indicated as the tackifier in solvent adhesives and hot-melt applied coatings and adhesives that must excel in these properties. Flytac 111-301 has an abietic acid of 0-0.1% max., a softening point (R&B) of 78°C, and a tetrahydro resin acid level of 30.0-40.0%. voir moins | |
| Flytac 114-125 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-125 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...voir plus Flytac 114-125 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. This product offers color stability, is resistant to yellowing, and has good heat resistance and adhesion. Flytac 114-125 has a color (Gardner Grade) of 5 max., an acid value of 30mg KOH/g max., and a softening point (R&B) of 125 ± 2°C min. voir moins | |
| Flytac 114-130 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-130 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...voir plus Flytac 114-130 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. It offers color stability, resistant to yellowing, good heat resistance and adhesion. Flytac 114-130 has a softening point (R&B) of 130 ± 2°C min., an acid value of 30mg KOH/g max., and a color (Gardener Grade) of 5 max. voir moins | |
| Flytac 114-135 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 114-135 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; impro...voir plus Flytac 114-135 is a slightly yellow transparent solid, which is adduct of gum rosin and maleic adhydride through the eaterification by glycerol or pentaerythritol. It is used in paint and coating industries widely, for production of phenolic paints; improve hardness of paint films, gloss and rubbing property for Polyesters, Nitro and PU paints. It offers color stability, resistant to yellowing, good heat resistance and adhesion. Flytac 114-135 has an acid value of 30mg KOH/g max., a color (Gardner Grade) of 5 max., and a softening point (R&B) of 135 ± 2°C min. voir moins | |
| Flytac 115 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 115 is a specially designed highly stable 50% water-borne polymeric type tackifier dispersion with 23 degree (rolling & ball) softening point. It is a highly stabilized rosin ester dispersion designed to provide superior performance in adhesives pr...voir plus Flytac 115 is a specially designed highly stable 50% water-borne polymeric type tackifier dispersion with 23 degree (rolling & ball) softening point. It is a highly stabilized rosin ester dispersion designed to provide superior performance in adhesives properties, and is compatible with anionic & nonionic types of latexes. It adheres to a wide range of substrates. This product has a viscosity ((Brookifield 2#, 60rpm, 25°C,cps) PH(25°C)) of 150 max, a particle size (AVG) of 0.25μm, and a density (25°C) of 1.02g/ml. voir moins | |
| Flytac 116-110 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-110 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is deal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 190 ± 10mg K...voir plus Flytac 116-110 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is deal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 190 ± 10mg KOH/g, a softening point (R&B) of 110± 5°C, and a color gardner (50% Benzene solution) of 5 max. voir moins | |
| Flytac 116-130 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-130 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideally used for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 180...voir plus Flytac 116-130 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideally used for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 180 ± 10mg KOH/g, a softening point (R&B) of 130 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. voir moins | |
| Flytac 116-150 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-150 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 170 ± 10mg ...voir plus Flytac 116-150 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, and coatings. This product has an acid value of 170 ± 10mg KOH/g, a softening point (R&B) of 150 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. voir moins | |
| Flytac 116-160 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 116-160 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 200 ± 10mg ...voir plus Flytac 116-160 is a rosin derivative modified by unsaturated acid and partially esterified with multi-alcohol. It is ideal for alcohol soluble intaglio printing inks, varnish and water-base inks, coatings etc. This product has an acid value of 200 ± 10mg KOH/g, a softening point (R&B) of 160 ± 5°C, and a color gardner (50% Benzene solution) of 8 max. voir moins | |
| Flytac 117-115 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-115 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-form...voir plus Flytac 117-115 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-115 has a softening point (R&B) of 110-120°C min., a dissoluble matter in hot water amount of 0.20, and an acid number of 145mg KOH/g min. voir moins | |
| Flytac 117-140 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-140 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-form...voir plus Flytac 117-140 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-140 has a softening point (R&B) of 135-145°C min., an acid number of 145mg KOH/g min., and a dissoluble matter in alcohol of 0.03% max. voir moins | |
| Flytac 117-95 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 117-95 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-formi...voir plus Flytac 117-95 is a polymerized rosin that is processed with the new advanced Sulphuric acid and Chloride Zinc method. It has many excellent properties including high softening point, anti-oxidation, non-crystallizing and good compatibility with film-forming agent. The typical uses for this product include ink, adhesive, paint, varnish, soldering flux, synthetic resin, etc. Flytac 117-95 has an acid number of 150mg KOH/g, a dissoluble matter in alcohol of 0.03% max., and a softening point (R&B) of 90-100°C min. voir moins | |
| FLYTAC 120-100W | Guangzhou Flying Dragon Chemical Ltd. | A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granu...voir plus A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granules, SBS and SIS base hot melt and pressure sensitive adhesives, EVA based hot melt adhesives for quality of packing, booking and cigarettes adhesives, hot melt paints and sealants and water or solvent bases adhesives. voir moins | |
| FLYTAC 120-90W | Guangzhou Flying Dragon Chemical Ltd. | A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granu...voir plus A granular, water white modified gum rosin polyols esters made from special refined gum rosin by series advanced processes of partial hydrogenation, esterification and stabilization. Applications include ot melt adhesive for white EVA glue sticks or granules, SBS and SIS base hot melt and pressure sensitive adhesives, EVA based hot melt adhesives for quality of packing, booking and cigarettes adhesives, hot melt paints and sealants and water or solvent bases adhesives. voir moins | |
| Flytac 188-C5 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C5 is a kind of thermal plasticizing resin produced by C5, by-products of petroleum cracking, through pretreatment, polymerization and distillation. The major usages are tackifier for pressure sensitive adhesive, because of its well balance PSA...voir plus Flytac 188-C5 is a kind of thermal plasticizing resin produced by C5, by-products of petroleum cracking, through pretreatment, polymerization and distillation. The major usages are tackifier for pressure sensitive adhesive, because of its well balance PSA properties such as trackness, adhesive strength and cohesive strength. It can also be used in the production of paints, adhesives and in rubber industries. Flytac 188-C5 has an average molecular weight of 1000-2600, a melt viscosity (CPS at 200°C) of 300 max., and a softening point (R&B) of 95-105°C. voir moins | |
| Flytac 188-C5/C9 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C5/C9 is a copolymerization hydrocarbon petroleum resin, whose materials are C5 fraction and C9 fraction. It is a new product for the market, and has the good characters of C5 hydrocarbon resin and C9 hydrocarbon resin. It is an important raw m...voir plus Flytac 188-C5/C9 is a copolymerization hydrocarbon petroleum resin, whose materials are C5 fraction and C9 fraction. It is a new product for the market, and has the good characters of C5 hydrocarbon resin and C9 hydrocarbon resin. It is an important raw material for the product of paints, adhesives, and in rubber industries. Flytac 188-C5/C9 has an ash content of 0.1% max., an acid value of 0.3mg KOH/g max., and a softening point (B&R) of 90~120°C max. voir moins | |
| Flytac 188-C9 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-C9 hydrocarbon petroleum resin is a kind of resin produced by C9 fraction, by products of petroleum cracking, through pretreatment,polymerization and distillation. It isn‘t a high polymer but a low polymer, with the molecular weight between 300...voir plus Flytac 188-C9 hydrocarbon petroleum resin is a kind of resin produced by C9 fraction, by products of petroleum cracking, through pretreatment,polymerization and distillation. It isn‘t a high polymer but a low polymer, with the molecular weight between 300-3000. It is an important raw material for the production of paints, adhesives and rubber industries. Flytac 188-C9 has a softening point (B&R) of 90-140°C, an acid value of 0.5mg KOH/g max., and an ash amount of 0.1% max. voir moins | |
| Flytac 188-HC5 | Guangzhou Flying Dragon Chemical Ltd. | Flytac 188-HC5 hydrocarbon resin is a low molecular weight fully hydrogenated, water-white, inert, thermoplastic resin derived from petrochemical feedstocks. This resin is especially designed as tackifier in hot-melt adhesives requiring excellent color re...voir plus Flytac 188-HC5 hydrocarbon resin is a low molecular weight fully hydrogenated, water-white, inert, thermoplastic resin derived from petrochemical feedstocks. This resin is especially designed as tackifier in hot-melt adhesives requiring excellent color retention upon aging. It is an important raw material for the production of paints, adhesives and rubber industries. Flytac 188-HC5 has a softening point (B&R) of 95-105°Cg, an acid value of 0.5mg KOH/g max., and an ash amount of 0.02% max. voir moins | |
| Flytac102-100F | Guangzhou Flying Dragon Chemical Ltd. | Flytac102-100F is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Ty...voir plus Flytac102-100F is a slightly yellow transparent solid, which is made from Gum Rosin through esaterification with Pentaerythritol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, and excellent polymer compatibility. Typical uses include EVA base hot melt glue sticks, bookbindings, Pressure-sensitive adhesive based on SIS or SBS Adhesive, emulsion and paints based on NR and CR.This product has a melt viscosity (CPS at 150°C) of 850-1300, a softening point (R&B) of 97-103°C, and a specific gravity (25°C/25°C) of 1.060~1.090. voir moins | |
| Flytac103-90 | Guangzhou Flying Dragon Chemical Ltd. | Flytac103-90 is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses...voir plus Flytac103-90 is a slightly yellow transparent solid, which is made from Gum Rosin through esterification with Glycerol. It has the properties of high viscosity, low VOC, excellent heat and aging stability, excellent polymer compatibility etc. Typical uses include EVA, SBS, SIS and other hot melt adhesives due to its stability and excellent polymer compatibility. It can also be used in construction adhesives, rubber compounding, sealants, coatings and other applications. This product has a colour gardener (in 50% Toleune) of 3 max., an acid value of 10mg KOH/g max., and a softening point (R&B) of 87-92°C min. voir moins | |
| Flytac105-E | Guangzhou Flying Dragon Chemical Ltd. | Flytac105-E is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-ox...voir plus Flytac105-E is the glycerol ester of hydrogenated rosin. It has found wide acceptance in chewing gum, hot-melt, pressure-sensitive, and laminating adhesives, as well as in wax depilatories. In general, it finds use where there is a need for a pale, non-oxidizing, color-stable, highly tacky liquid resin. This product is ideally used for wax modification, waterborne adhesives, tapes and labels, solventborne adhesives, rubber and plastic modification, and paint and coatings. Flytac105-E has a softening point (R&B) of 78-88°C min., a specific gravity (25°C/25°C) of 1.060~1.090, and an ash content of 0.1% max. voir moins | |
| KTR-100 | Suparna Chemicals Ltd. | KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-100 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-100 has a softening point of 95 to 105 °C, in butyl acetate of 75 to 95 at 25 °C (cps), and a hydroxyl value of 170 to 200. voir moins | |
| KTR-118 | Suparna Chemicals Ltd. | KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-118 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-118 has a softening point of 105 to 115 °C, in butyl acetate of 100 to 120 at 25 °C (cps), and a hydroxyl value of 180 to 210. voir moins | |
| KTR-123 | Suparna Chemicals Ltd. | KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries...voir plus KTR-123 is a ketonic resin that has the appearance of white prills. It is neutral, light in color, and inert to saponification. It displays good pigment-wetting properties, and increases yield of coating systems. It is suitable for all types of industries, including nitrocellulose paints where it improves polishing characteristic and adhesion. In printing inks, it enhances adhesion, imparts gloss, improves drying properties, and increases solids content, where it is used in maleic resins, alkyd resins, nitro cellulose, and polyvinyl butyral. KTRs are also used in isocyanate based adhesive systems, as well as radiation cured adhesives and in water clear systems. KTR-123 has a softening point of 105 to 115 °C, in butyl acetate of 110 to 140 at 25 °C (cps), and a hydroxyl value of 200 to 230. voir moins | |
| LX®-1035 Resin | Neville Chemical Company | LX®-1035 Resin is a flaked resin that improves cohesive strength and promotes heat resistance of adhesives. In addition it can contribute to rapid solvent release and faster drying of litho inks. It has applications in the adhesives and sealants industry ...voir plus LX®-1035 Resin is a flaked resin that improves cohesive strength and promotes heat resistance of adhesives. In addition it can contribute to rapid solvent release and faster drying of litho inks. It has applications in the adhesives and sealants industry as well as in certain coatings related to the automobile industry. voir moins | |
| LX®-1200 | Neville Chemical Company | LX®-1200 is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, improves tack and bond strength in adhesives and enhances leafing and brilliance in metallic paints and inks. It is applied to mastics, constructi...voir plus LX®-1200 is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, improves tack and bond strength in adhesives and enhances leafing and brilliance in metallic paints and inks. It is applied to mastics, construction and flooring adhesives, high solids solvent-borne alkyd based coatings, litho printing inks and aluminum paint. voir moins | |
| LX®-1200, 130 | Neville Chemical Company | LX®-1200, 130 is an inert thermoplastic hydrocarbon resin flake. This product is applied to mastics, construction and flooring adhesives, high solids solvent-borne alkyd based coatings, litho printing inks, metallic litho printing inks and aluminum paint. | |
| LX®-2161 Resin | Neville Chemical Company | LX®-2161 Resin is an inert thermoplastic hydrocarbon resin of amber flakes that enhances the wetting of pigments and fillers, improves tack and bond strength in adhesives and are soluble in aliphatic solvents and vegetable oils. They can be applied to lit...voir plus LX®-2161 Resin is an inert thermoplastic hydrocarbon resin of amber flakes that enhances the wetting of pigments and fillers, improves tack and bond strength in adhesives and are soluble in aliphatic solvents and vegetable oils. They can be applied to litho printing inks and high solids solvent-borne alkyd based coatings in addition to mastics, construction and flooring adhesives. voir moins | |
| LX®-238 Resin | Neville Chemical Company | LX®-238 Resin is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, is soluble in aromatic and aliphatic solvents/oils and has applications for use in high solids solvent-borne alkyd based coatings and concret...voir plus LX®-238 Resin is an inert thermoplastic hydrocarbon resin. This product promotes wetting of pigments and fillers, is soluble in aromatic and aliphatic solvents/oils and has applications for use in high solids solvent-borne alkyd based coatings and concrete cure compounds. voir moins | |
| MM-204 | Designer Molecules | MM-204 is a light tan liquid mono-functional acrylate monomer. This product features low viscosity, hydrolytically resistant, high glass transition temperature, diluent for thermoset resins, low cure shrinkage, and high Tg. MM-204 is most commonly used as...voir plus MM-204 is a light tan liquid mono-functional acrylate monomer. This product features low viscosity, hydrolytically resistant, high glass transition temperature, diluent for thermoset resins, low cure shrinkage, and high Tg. MM-204 is most commonly used as a reactive diluent for UV or peroxide cured resins in coating or adhesive applications. voir moins | |
| MM-211 | Designer Molecules | MM-211 is a light yellow powder terminated carboxylic acid. This product features flexible aliphatic backbone, maleimide and carboxylic acid functional groups, and adhesion promoter. MM-211 is most commonly used in synthetic resins and adhesion promoting ...voir plus MM-211 is a light yellow powder terminated carboxylic acid. This product features flexible aliphatic backbone, maleimide and carboxylic acid functional groups, and adhesion promoter. MM-211 is most commonly used in synthetic resins and adhesion promoting applications. voir moins | |
| MM-220 | Designer Molecules | MM-220 is a light yellow liquid mono-acrylate monomer. This product features low weight loss on cure, helps reduce cure shrinkage, and low viscosity. MM-220 is most commonly used as a reactive diluent for UV or peroxide cured resins, coatings and adhesive...voir plus MM-220 is a light yellow liquid mono-acrylate monomer. This product features low weight loss on cure, helps reduce cure shrinkage, and low viscosity. MM-220 is most commonly used as a reactive diluent for UV or peroxide cured resins, coatings and adhesive applications. voir moins | |
| MM-281 | Designer Molecules | MM-281 is a white to off white solid carboxylic acid. It is a useful intermediate for the synthesis of ester and amide linked thermoset monomers. This product features flexible aliphatic backbone, maleimide and carboxylic acid functional groups, and adhes...voir plus MM-281 is a white to off white solid carboxylic acid. It is a useful intermediate for the synthesis of ester and amide linked thermoset monomers. This product features flexible aliphatic backbone, maleimide and carboxylic acid functional groups, and adhesion promoter. MM-281 is most commonly used in resins and adhesion promoter applications. voir moins | |
| MM-290 | Designer Molecules | MM-290 is a light tan liquid acrylate monomer. This product features lower weight loss on cure than Isobornyl Acrylate (IBOA), mild pleasant odor, and hydrolytic resistance. MM-290 is a most commonly used in hydrolytic resistance applications. | |
| MM-304 | Designer Molecules | MM-304 is a colorless liquid methacrylate monomer. This product features lower weight loss on cure than Isobornyl methacrylate (IBOMA), mild pleasant odor, hydrolytic resistance, and very low color. MM-304 is most commonly used in hydrolytic resistance ap...voir plus MM-304 is a colorless liquid methacrylate monomer. This product features lower weight loss on cure than Isobornyl methacrylate (IBOMA), mild pleasant odor, hydrolytic resistance, and very low color. MM-304 is most commonly used in hydrolytic resistance applications. voir moins | |
| NEVCHEM® 100 | Neville Chemical Company | NEVCHEM® 100 is a thermoplastic hydrocarbon resin that improves track and bond strength in adhesive and caulks, promote wetting of pigments and fillers, provide leafing characteristics for metallic pigments and enable good thermal stability. They are use...voir plus NEVCHEM® 100 is a thermoplastic hydrocarbon resin that improves track and bond strength in adhesive and caulks, promote wetting of pigments and fillers, provide leafing characteristics for metallic pigments and enable good thermal stability. They are used in hot melt and construction adhesives, sealants and caulks, high solids solvent-borne and alkyd based coatings and litho printing inks. voir moins | |
| NEVCHEM® 110 | Neville Chemical Company | NEVCHEM® 110 is a thermoplastic hydrocarbon resin that promotes tack and bond strength in adhesive and caulks, enhances wetting and pigments of fillers, provide leafing characteristics for metallic pigments and give thermal stability. They are applied to ...voir plus NEVCHEM® 110 is a thermoplastic hydrocarbon resin that promotes tack and bond strength in adhesive and caulks, enhances wetting and pigments of fillers, provide leafing characteristics for metallic pigments and give thermal stability. They are applied to hot melt and construction adhesives, sealants and caulks, high solids solvent-borne and alkyd based coatings and be used in asphalt modification. voir moins |
