| FAST SCARLET BHXL | Zhejiang Baihe Chemical Holding Group Company | FAST SCARLET BHXL is a calcium salt 2B pigment with high transparency and gloss. Due to its good resistance to solvents, it is especially recommended for solvent based printing ink applications. This product has an oil absorption of 45-55 ml/100g and a pH...展开 FAST SCARLET BHXL is a calcium salt 2B pigment with high transparency and gloss. Due to its good resistance to solvents, it is especially recommended for solvent based printing ink applications. This product has an oil absorption of 45-55 ml/100g and a pH value of 7.5-8.5. It is often used in PA inks, NC inks, UV inks, and PP inks. 收起 | |
| FAST SCARLET GN | Zhejiang Baihe Chemical Holding Group Company | FAST SCARLET GN is a bright yellow shaded red barium 2B pigment. This product has an oil absorption of 35-45 ml/100g and a pH value of 7-8. It is suitable for use in offset inks and PVC. | |
| FAST SCARLET GS | Zhejiang Baihe Chemical Holding Group Company | FAST SCARLET GS is a strontium salt 2B pigment. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is suitable for use in industrial paint, powder coatings, water based inks, and PVC. | |
| FAST SCARLET WI | Zhejiang Baihe Chemical Holding Group Company | FAST SCARLET WI is a bright yellow shaded red barium 2B pigment. It exhibits good dispersion in both water and solvent based liquid inks. This product has an oil absorption of 35-45 ml/100g and a pH value of 7-8. It is recommended for water based inks, PA...展开 FAST SCARLET WI is a bright yellow shaded red barium 2B pigment. It exhibits good dispersion in both water and solvent based liquid inks. This product has an oil absorption of 35-45 ml/100g and a pH value of 7-8. It is recommended for water based inks, PA, and PP inks. 收起 | |
| FAST SCARLET WI-03 | Zhejiang Baihe Chemical Holding Group Company | FAST SCARLET WI-03 is a strontium salt 2B pigment with good dispersion in both water and solvent based liquid inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for water based inks, powder coating, and PA ...展开 FAST SCARLET WI-03 is a strontium salt 2B pigment with good dispersion in both water and solvent based liquid inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for water based inks, powder coating, and PA inks. 收起 | |
| FLUBE CA 140 | DKSH | FLUBE CA 140 is a calcium salt of polymer of naphthalenesulphonic acids condensed with formaldehyde. | Request Sample |
| FLUBE CA 140 F | DKSH | FLUBE CA 140 F is a calcium salt of polymer of naphthalenesulphonic acids condensed with formaldehyde. | Request Sample |
| FLUBE CA 40 F | DKSH | FLUBE CA 40 F is a calcium salt of polymer of naphthalenesulphonic acids condensed with formaldehyde. | Request Sample |
| FLUBE CA-40 | DKSH | FLUBE CA-40 is a calcium salt of polymer of naphthalenesulphonic acids condensed with formaldehyde. | Request Sample |
| FLUBE CR 100 F | DKSH | FLUBE CR 100 F is a sodium salt of polymer of naphthalene-sulphonic acids condensed with formaldehyde. | Request Sample |
| FLUBE OS 139 F | DKSH | FLUBE OS 139 F is a sodium salt of polymer of naphthalene-sulphonic acids condensed with formaldehyde. | Request Sample |
| FLUBE OS-39 | DKSH | FLUBE OS-39 is a sodium salt of polymer of naphthalenesulphonic acids condensed with formaldehyde. | Request Sample |
| GAP 1E | DKSH | GAP 1E is a leafing aluminum pigment in paste. It has irregular flakes of medium particle size. It is a solvent: Mineral spirit. GAP Line are versatile aluminum pastes and powders available in different particle sizes for leafing and non-leafing, ideal fo...展开 GAP 1E is a leafing aluminum pigment in paste. It has irregular flakes of medium particle size. It is a solvent: Mineral spirit. GAP Line are versatile aluminum pastes and powders available in different particle sizes for leafing and non-leafing, ideal for industrial applications. Its main applicaitons are aluminium leafing and non-leafing for low end (hammer effect and protective) solvent-born. This Product is available in Asia Pacific and Europe (only UK, Germany and Italy). 收起 | Request Sample |
| Gi-PW-F031 | DKSH | Gi-PW-F031 is few layers graphene powder. It presents an economic solution to increase the mechanical strengths with less dosage than current additive on polymer, resin and rubber composites applications. | Request Sample |
| GMA | DKSH | Glycidyl methacrylate (GMA) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy funct...展开 Glycidyl methacrylate (GMA) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy functionalization to polyolefins and other acrylate resins. Glycidyl methacrylate is produced by several companies worldwide, including Dow Chemical. This product is available in Europe and Asia. 收起 | Request Sample |
| GMA 97 | DKSH | Glycidyl methacrylate (GMA 97) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy fu...展开 Glycidyl methacrylate (GMA 97) is an ester of methacrylic acid and a common monomer used in the creation of epoxy resins. While typical home epoxies contain diglycidyl ether of bisphenol A (DGEBA), glycidyl methacrylate is instead used to provide epoxy functionalization to polyolefins and other acrylate resins. Glycidyl methacrylate is produced by several companies worldwide, including Dow Chemical. This product is available in Europe and Asia. 收起 | Request Sample |
| Graphene Nanoplatelets | DKSH | Graphene is an allotrope of carbon whose structure is a single planar sheet of sp2 bonded carbon atoms that are densely packed in a honeycomb crystal lattice. Graphene Nanoplatelets are reduced graphene layers.This product is available in Europe, Asia and...展开 Graphene is an allotrope of carbon whose structure is a single planar sheet of sp2 bonded carbon atoms that are densely packed in a honeycomb crystal lattice. Graphene Nanoplatelets are reduced graphene layers.This product is available in Europe, Asia and North America. 收起 | Request Sample |
| HANSA YELLOW 103 | Zhejiang Baihe Chemical Holding Group Company | HANSA YELLOW 103 is an aryl amide azo pigment with a green tint and good resistance properties. This product has an oil absorption of 25-35 ml/100g and a pH value of 6.5-7.5. It is recommended for water based decorative paints. industrial paints, and powd...展开 HANSA YELLOW 103 is an aryl amide azo pigment with a green tint and good resistance properties. This product has an oil absorption of 25-35 ml/100g and a pH value of 6.5-7.5. It is recommended for water based decorative paints. industrial paints, and powder coatings. 收起 | |
| HANSA YELLOW 133 | Zhejiang Baihe Chemical Holding Group Company | HANSA YELLOW 133 is an aryl amide yellow pigment with good weather resistance in strong shades. This product has an oil absorption of 25-35 ml/100g and a pH value of 6-7. It is recommended for water based decorative paints, industrial paints, and powder c...展开 HANSA YELLOW 133 is an aryl amide yellow pigment with good weather resistance in strong shades. This product has an oil absorption of 25-35 ml/100g and a pH value of 6-7. It is recommended for water based decorative paints, industrial paints, and powder coatings. 收起 | |
| HARDLEN 13LP | DKSH | HARDLEN 13LP is a resin grafted with Chlorine (CPO), which has good adhesion power to Polyolefins without any surface treatment. HARDLEN 13LP main characteristics are: excellent Adhesion Promoter to plastics without any surface treatment such as corona or...展开 HARDLEN 13LP is a resin grafted with Chlorine (CPO), which has good adhesion power to Polyolefins without any surface treatment. HARDLEN 13LP main characteristics are: excellent Adhesion Promoter to plastics without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN 13LP main applications is adhesive for Polyolefins, Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN 15LP | DKSH | HARDLEN 15LP is a resin grafted with Chlorine (CPO) which has good adhesion power to Polyolefins without any surfase treatment. HARDLEN 15LP main characteristics are: ecellent Adhesion Promoter without any surface treatment such as corona or flame. Availa...展开 HARDLEN 15LP is a resin grafted with Chlorine (CPO) which has good adhesion power to Polyolefins without any surfase treatment. HARDLEN 15LP main characteristics are: ecellent Adhesion Promoter without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN 15LP main applications are: gravure and printing ink, hot-stamping ink Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN CY1321P | DKSH | HARDLEN CY1321P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY1321P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolef...展开 HARDLEN CY1321P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY1321P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any C14surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN CY1321P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN CY2321P | DKSH | HARDLEN CY2321P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY2321P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolef...展开 HARDLEN CY2321P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY2321P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN CY2321P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN CY2329 | DKSH | HARDLEN CY2329 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY2329 main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefin...展开 HARDLEN CY2329 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY2329 main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. HARDLEN CY2329 main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN CY9122P | DKSH | HARDLEN CY9122P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY9122P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolef...展开 HARDLEN CY9122P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY9122P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN CY9122P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN CY9124P | DKSH | HARDLEN CY9124P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY9124P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolef...展开 HARDLEN CY9124P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN CY9124P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN CY9124P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN DX523P | DKSH | HARDLEN DX523P is a resin grafted with Chlorine which has good adhesion power to Polyolefins without any surfase treatment. HARDLEN DX523P main characteristics are: ecellent Adhesion Promoter to plastics without any surface treatment such as corona or fla...展开 HARDLEN DX523P is a resin grafted with Chlorine which has good adhesion power to Polyolefins without any surfase treatment. HARDLEN DX523P main characteristics are: ecellent Adhesion Promoter to plastics without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN DX523P main applications are: gravure printing ink, hot-stamping ink and UV ink to Polyolefins. Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN DX526P | DKSH | HARDLEN DX526P is a resin grafted with Chlorinewhich has good adhesion power to Polyolefins without any surfase treatment. HARDLEN DX526P main characteristics are: ecellent Adhesion Promoter to plastics without any surface treatment such as corona or flam...展开 HARDLEN DX526P is a resin grafted with Chlorinewhich has good adhesion power to Polyolefins without any surfase treatment. HARDLEN DX526P main characteristics are: ecellent Adhesion Promoter to plastics without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN DX526P main applications are: gravure printing ink, hot-stamping ink and UV ink to Polyolefins. Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN DX530P | DKSH | HARDLEN DX530P is a resin grafted with Chlorinewhich has good adhesion power to Polyolefins without any surfase treatment. HARDLEN DX530P main characteristics are: ecellent Adhesion Promoter to plastics without any surface treatment such as corona or flam...展开 HARDLEN DX530P is a resin grafted with Chlorinewhich has good adhesion power to Polyolefins without any surfase treatment. HARDLEN DX530P main characteristics are: ecellent Adhesion Promoter to plastics without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN DX530P main applications are: gravure printing ink, hot-stamping ink and UV ink to Polyolefins. Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN EH801J | DKSH | HARDLEN EH801J is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EH801J main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins...展开 HARDLEN EH801J is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EH801J main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins without any surface treatment such as corona or flame. HARDLEN EH801J main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN EW5250 | DKSH | HARDLEN EW5250 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EW5250 main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins...展开 HARDLEN EW5250 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EW5250 main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins without any surface treatment such as corona or flame. HARDLEN EW5250 main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN EW5515 | DKSH | HARDLEN EW5515 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EW5515 main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins...展开 HARDLEN EW5515 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EW5515 main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins without any surface treatment such as corona or flame. HARDLEN EW5515 main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN EZ2250 | DKSH | HARDLEN EZ2250 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EZ2250 main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins...展开 HARDLEN EZ2250 is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN EZ2250 main characteristics are: ecellent Adhesion Promoter to palstic and various polyolefins without any surface treatment such as corona or flame. HARDLEN EZ2250 main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN F-225P | DKSH | HARDLEN F-225P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN F-225P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefin...展开 HARDLEN F-225P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN F-225P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN F225P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN F2P | DKSH | HARDLEN F2P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN F2P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins with...展开 HARDLEN F2P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN F2P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN F2P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN F6P | DKSH | HARDLEN F6P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN F6P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins with...展开 HARDLEN F6P is a resin grafted with Chlorine and Maleic anhydride, which has good adhesion power to Polyolefins or CPO without any surfase treatment. HARDLEN F6P main characteristics are: ecellent Adhesion Promoter to plastics and various polyolefins without any surface treatment such as corona or flame. Available to choose Solvent base system (Aromatic or HAPS free). HARDLEN F6P main applications are: Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN NZ1004 | DKSH | HARDLEN NZ1004 is a chlorine free resin grafted with C Maleic anhydride, which has good adhesion power to Polyolefins or plastics without any surfase treatment. HARDLEN NZ1004 main characteristics are: ecellent Adhesion Promoter to Clorinated Polyolefins ...展开 HARDLEN NZ1004 is a chlorine free resin grafted with C Maleic anhydride, which has good adhesion power to Polyolefins or plastics without any surfase treatment. HARDLEN NZ1004 main characteristics are: ecellent Adhesion Promoter to Clorinated Polyolefins without any surface treatment such as corona or flame. HARDLEN NZ1004 main applications are: Vehicles for gravure printing ink, hot-stamping ink and UV ink to Polyolefins. Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| HARDLEN NZ1015 | DKSH | HARDLEN NZ1015 is a chlorine free resin grafted with C Maleic anhydride, which has good adhesion power to Polyolefins or plastics without any surfase treatment. HARDLEN NZ1015 main characteristics are: ecellent Adhesion Promoter to Clorinated Polyolefins ...展开 HARDLEN NZ1015 is a chlorine free resin grafted with C Maleic anhydride, which has good adhesion power to Polyolefins or plastics without any surfase treatment. HARDLEN NZ1015 main characteristics are: ecellent Adhesion Promoter to Clorinated Polyolefins without any surface treatment such as corona or flame. HARDLEN NZ1015 main applications are: Vehicles for gravure printing ink, hot-stamping ink and UV ink to Polyolefins. Primer (Pigmented or conductive) to PP-bumper, 1-coat paint to interior car Parts and wheel-cap paint. Binder for flocking. Lamination to PP/Printing-Paper. PP film/ PP film, Foils or Sheet etc. Heat-seal agent to PP Film/Sheet. Available in select countries. Please inquire for more details. 收起 | Request Sample |
| IAAC | DKSH | IAAC is used in solvent-based formulas of automotive, industrial and wood paints and thinner formulations. In paint formulas, IAAC is an excellent active solvent, of medium evaporation rate in most acrylic, cellulose (nitro, CAB), epoxy, polyester, polyur...展开 IAAC is used in solvent-based formulas of automotive, industrial and wood paints and thinner formulations. In paint formulas, IAAC is an excellent active solvent, of medium evaporation rate in most acrylic, cellulose (nitro, CAB), epoxy, polyester, polyurethane resins and hybrid systems. It reduces the evaporation rates of the systems, which allows a suitable balance of solvency and guarantees the presence of the active solvent during drying. It also acts as an aid in the elimination of blush, preventing the bleaching of paints after application in very wet environments. It finds use in original automotive, refinishing paints, lacquers and thinners, in combination with slower evaporation solvents, like butyl glycol acetate, ethyl glycol acetate and butyl glycol. IAAC has high electrical resistivity, acting as a conductivity regulator, which contributes toward improving the performance and deposition characteristics of solvent-based paints applied electrostatically. In formulas of paints for wood, IAAC provides a film with excellent leveling and sheen characteristics. Chemical name: Isopentyl Acetate, Acetic Amyl Ester. Molecular formula: CH3COO (CH2)2CH (CH3)2. This product is available in Europe, Asia and North America. 收起 | Request Sample |
| IONPURE | DKSH | IONPURE is a soluble glass containing anti-microbial metal ions. It maintains the transparency when added to PP, PVC, PC, ABS, PC. It exhibits a high heat resistance and high performance at low concentration. IONPURE is not discolored by compounding and w...展开 IONPURE is a soluble glass containing anti-microbial metal ions. It maintains the transparency when added to PP, PVC, PC, ABS, PC. It exhibits a high heat resistance and high performance at low concentration. IONPURE is not discolored by compounding and with age, as it can control the speed of releasing metal ions. It is suitable for use in flooring materials and wallpapers. 收起 | Request Sample |
| IPDA | DKSH | IPDA is a colorless or pale yellow transparent liquid with an amine-like odor at room temperature. It is a mixture of two stero-isomers of 3-aminomethyl-3,5,5-trimethylcyclohe-xylamine. IPDA is a cycloalifatic diamine with special structure and is used in...展开 IPDA is a colorless or pale yellow transparent liquid with an amine-like odor at room temperature. It is a mixture of two stero-isomers of 3-aminomethyl-3,5,5-trimethylcyclohe-xylamine. IPDA is a cycloalifatic diamine with special structure and is used in all typical reactions of this kind of amine functional chemicals. It is widely miscible with a full range of alifatic, aromatic and halogenated solvents of different polarity. Chemical description: 3-aminomethyl-3,5,5-trimethylcyclohexylamine. This product is available in Europe and Korea. 收起 | Request Sample |
| ITAMID B | DKSH | ITAMID B is a polyaminoamide resin of high viscosity at room temperature and which is used combined with liquid or solid epoxy resins to obtain products hardening even at room temperature and which is used in the anticorrosion paints, protective coatings ...展开 ITAMID B is a polyaminoamide resin of high viscosity at room temperature and which is used combined with liquid or solid epoxy resins to obtain products hardening even at room temperature and which is used in the anticorrosion paints, protective coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces. ITAMID B, which can also be used neat, is usually used in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. In solvent free systems ITAMID B is usually used in combination with liquid epoxy resins giving high adhesion properties. With an epoxy resin of an epoxy weight equivalent of about 190g/eq, ITAMID B is normally used in equal parts. This ratio can be varied, even widely, whilst bearing in mind that a greater percentage of polyamide resin increases flexibility but reduces resistance to chemicals. More frequently ITAMID B is combined with a solid epoxy resin in solvent systems whose pot-life changes with the percentage of solvent and temperature in addition to the type of epoxy resin used. For example, a formulation with 40% of solvents with an epoxy resin of epoxy equivalent weight 475 and a ratio of 65/35 epoxy to polyamide will exhibit a pot-life at room temperature of about two days. 收起 | Request Sample |
| ITAMID C | DKSH | ITAMID C is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C is used above all in the field of anticorrosion paints, protective coatings with high resi...展开 ITAMID C is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C is used above all in the field of anticorrosion paints, protective coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces. ITAMID C, can be dissolved readily in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. In solvent free systems, ITAMID C when used combined with liquid epoxy resins gives rise to products featuring high adhesion properties and which can be applied by spatula process or by spraying. When ITAMID C is used with an epoxy resin with an epoxy equivalent weight of around 190, the normal ratio used is 60 p.p. of epoxy to 40 p.p. of polyaminoamide. However, this ratio can be varied, even widely, whilst bearing in mind that a greater percentage of polyamine resin increases flexibility but reduces resistance to chemicals. In solvent systems ITAMID C is usually combined with a solid epoxy resin whose pot-life changes with the percentage of dryness and temperature in addition to the type of epoxy used. For example, a formulation at dryness 40% with an epoxy resin of epoxy weight equivalent 475 and a ratio of 75/25 epoxy to polyamine will exhibit a pot-life at room temperature of about two days. 收起 | Request Sample |
| ITAMID C/F | DKSH | ITAMID C/F is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C/F is used above all in the field of anticorrosion paints, protective coatings with high ...展开 ITAMID C/F is a medium viscosity polyaminoamide resin which is used combined with liquid or solid epoxy resins to obtain room temperature hardening products. ITAMID C/F is used above all in the field of anticorrosion paints, protective coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces. ITAMID C/F, can be dissolved readily in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. In solvent free systems, ITAMID C/F when used combined with liquid epoxy resins gives rise to products featuring high adhesion properties and which can be applied by spatula process or by spraying. When ITAMID C/F is used with an epoxy resin with an epoxy equivalent weight of around 190, the normal ratio used is 60 p.p. of epoxy to 40 p.p. of polyaminoamide. However, this ratio can be varied, even widely, whilst bearing in mind that a greater percentage of polyamine resin increases flexibility but reduces resistance to chemicals. In solvent systems ITAMID C/F is usually combined with a solid epoxy resin whose pot-life changes with the percentage of dryness and temperature in addition to the type of epoxy used. For example, a formulation at dryness 40% with an epoxy resin of epoxy weight equivalent 475 and a ratio of 75/25 epoxy to polyamine will exhibit a pot-life at room temperature of about two days. 收起 | Request Sample |
| ITAMID D | DKSH | ITAMID D is a rather fluid polyaminoamide resin which is used in combination with epoxy resins, mainly liquid ones, to obtain hardening products even at room temperature and which are used above all in the field of reactive adhesives, solvent free coating...展开 ITAMID D is a rather fluid polyaminoamide resin which is used in combination with epoxy resins, mainly liquid ones, to obtain hardening products even at room temperature and which are used above all in the field of reactive adhesives, solvent free coatings with high resistance to chemical agents in general and with excellent properties of toughness, flexibility and adhesion to the most different surfaces and good thermal resistance. ITAMID D, which is normally used neat, however dissolves readily in organic solvents such as alcohol, aromatic hydrocarbons, glycol ethers and their mixtures. The low viscosity of ITAMID D when used in combination with liquid epoxy resins gives rise to products which can be applied even by processes of spatula, spraying and pouring. When ITAMID D is used in combination with an epoxy resin with a epoxy equivalent weight of around 190, depending on the applications the ratio between epoxy and polyamine may vary between 65/35 and 75/25 with pot-lives varying between 110 and 130 minutes. It must however be keep in mind that a higher percentage of polyamine resin increases flexibility but reduces the resistance to chemical agents. 收起 | Request Sample |
| ITAMID FL 560 | DKSH | ITAMID FL 560 is a modified polyamide-imidazolinic hardner for epoxy resins. It can be used for primers or adhesion promoters. Phenol free, Bisphenol A free, High adhesion on wet concrete and Very good handling. | Request Sample |
| ITAMID FL 560S | DKSH | ITAMID FL 560S is a modified polyamide-imidazolinic hardner for epoxy resins. It can be used for primers or adhesion promoters. Phenol free, Bisphenol A free, High adhesion on wet concrete, Quick Shore D development also at low temperature and Very good h...展开 ITAMID FL 560S is a modified polyamide-imidazolinic hardner for epoxy resins. It can be used for primers or adhesion promoters. Phenol free, Bisphenol A free, High adhesion on wet concrete, Quick Shore D development also at low temperature and Very good handling. 收起 | Request Sample |
| ITAMID FL300 | DKSH | ITAMID FL300 is a liquid epoxy resin hardener made up of low viscosity polyaminoamide resin. ITAMID FL300 is to be found used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masses,...展开 ITAMID FL300 is a liquid epoxy resin hardener made up of low viscosity polyaminoamide resin. ITAMID FL300 is to be found used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masses, paints and floorings. Compared with traditional hardeners, ITAMID FL300 exhibits lower sensitivity to carbonatation and higher reactivity. Hardening times can be considerably reduced by including into the formulate either appropriate accelerator substances (e.g. 2-3% of tris(dimethylaminomethyl)phenol) or fastcure hardener like ITAMINE M150 or ITAMINE MB501. 收起 | Request Sample |
| ITAMID FL31 | DKSH | ITAMID FL31 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL31 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings...展开 ITAMID FL31 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL31 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings. Compared with traditional hardeners, ITAMID FL31 exhibits no sensitivity to carbonatation and higher reactivity. Hardening times can be considerably reduced by including into the formulate either appropriate accelerator substances (e.g. 2-3% of tris(dimethylaminomethyl)phenol) or fastcure hardener like ITAMINE M160 or ITAMINE MB501. 收起 | Request Sample |
| ITAMID FL32 | DKSH | ITAMID FL32 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL32 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings...展开 ITAMID FL32 is a liquid epoxy resin hardener made up of low viscosity, modifyed polyaminoamide-imidazoline resin. ITAMID FL32 is used in the formulation of epoxy mortars (for repair of concrete, etc.), in the formulation of adhesives, paints and floorings. Compared with traditional hardeners, ITAMID FL32 exhibits no sensitivity to carbonatation and higher reactivity. Hardening times can be considerably reduced by including into the formulate either appropriate accelerator substances (e.g. 2-3% of tris(dimethylaminomethyl)phenol) or fastcure hardener like ITAMINE M160 or ITAMINE MB501. 收起 | Request Sample |
| ITAMID FL328 | DKSH | ITAMID FL328 is a liquid epoxy resin hardener made up of low viscosity, modified polyaminoamide adduct. ITAMID FL328 allow the dispersion of epoxy resin in water. ITAMID FL328 is used in the formulation of epoxy mortars (for laying tiles, repair of concre...展开 ITAMID FL328 is a liquid epoxy resin hardener made up of low viscosity, modified polyaminoamide adduct. ITAMID FL328 allow the dispersion of epoxy resin in water. ITAMID FL328 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.) and primer. 收起 | Request Sample |
| ITAMID FL40/S | DKSH | ITAMID FL40/S is a liquid epoxy resin hardener made up of low viscosity polyaminoamide-imidazoline resin. ITAMID FL40/S is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masse...展开 ITAMID FL40/S is a liquid epoxy resin hardener made up of low viscosity polyaminoamide-imidazoline resin. ITAMID FL40/S is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, poured masses, paints and floorings. Compared with traditional hardeners, ITAMID FL40/S exhibits lower sensitivity to carbonatation and lower reactivity, i.e. it gives longer utilisation and hardening times. 收起 | Request Sample |
| ITAMID FL41W3 | DKSH | ITAMID FL41W3 is a liquid epoxy resin hardener made up of a modified, low viscosity polyaminoamide resin. ITAMID FL41W3 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, encapsulatio...展开 ITAMID FL41W3 is a liquid epoxy resin hardener made up of a modified, low viscosity polyaminoamide resin. ITAMID FL41W3 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, encapsulations and paints. Compared with traditional hardeners, ITAMID FL41W3 exhibits improved resistance to chemical agents and dilute inorganic acids, and pronounced capacity for reaction at low temperatures and in presence of water. 收起 | Request Sample |
| ITAMID FL520 | DKSH | ITAMID FL520, is a liquid epoxy resin modified polyaminoamide-imidazoline. With liquid epoxy resins can be used for primers or adhesion promoters in concrete substrate. It is a solvent free and it can be applied in wet substrate. The principle characteris...展开 ITAMID FL520, is a liquid epoxy resin modified polyaminoamide-imidazoline. With liquid epoxy resins can be used for primers or adhesion promoters in concrete substrate. It is a solvent free and it can be applied in wet substrate. The principle characteristics are: low viscosity, very good corrosion protection, good making propriety, good adhesion in wet substrate with high percentage of humidity and slight flexibility with high levels of mortar stability. 收起 | Request Sample |
| ITAMID FL520/S | DKSH | ITAMID FL520/S is a liquid epoxy resin modified polyaminoamide-imidazoline. With liquid epoxy resins can be used for primers or adhesion promoters in concrete substrate. It can be applied in wet substrate, in the formulation of adhesives, encapsulations a...展开 ITAMID FL520/S is a liquid epoxy resin modified polyaminoamide-imidazoline. With liquid epoxy resins can be used for primers or adhesion promoters in concrete substrate. It can be applied in wet substrate, in the formulation of adhesives, encapsulations and paints. The principle characteristics are: low viscosity, very good corrosion protection, good making propriety, good adhesion in wet substrate with high percentage of humidity, slight flexibility with high levels of mortar stability and good capacity for reaction at low temperatures and high percentage of humidity. 收起 | Request Sample |
| ITAMID FL540 | DKSH | ITAMID FL540, is a liquid epoxy resin hardener made up of a low viscosity, modified polyaminoamide adduct. ITAMID FL540 is used in the formulation of adhesives, epoxy mortars and paints even on wet surfaces and under water. | Request Sample |
| ITAMID FL550/S | DKSH | ITAMID FL550/S is a liquid epoxy resin modified polyaminoamide-imidazoline. With liquid epoxy resins can be used for primers or adhesion promoters in concrete substrate. It can be applied in wet substrate, in the formulation of adhesives, encapsulations a...展开 ITAMID FL550/S is a liquid epoxy resin modified polyaminoamide-imidazoline. With liquid epoxy resins can be used for primers or adhesion promoters in concrete substrate. It can be applied in wet substrate, in the formulation of adhesives, encapsulations and paints. The principle characteristics are: low viscosity, very good corrosion protection, good making propriety, good adhesion in wet substrate with high percentage of humidity, slight flexibility with high levels of mortar stability and good capacity for reaction at low temperatures and high percentage of humidity. 收起 | Request Sample |
| ITAMID M20P | DKSH | The ITAMID M20P is a solid polyamide resin excellent thermal stability which are mainly used in adhesives Fusion (Hot Melts). The ITAMID M20P is particularly useful for the formulation of inks “flex” and “rotogravure” where over membership, gloss and wate...展开 The ITAMID M20P is a solid polyamide resin excellent thermal stability which are mainly used in adhesives Fusion (Hot Melts). The ITAMID M20P is particularly useful for the formulation of inks “flex” and “rotogravure” where over membership, gloss and water resistance, are also required a higher resistance to ink “gel”, one of his quick recovery from the phase of “gel” and a resistance to “blocking”. The ITAMID M20P has an excellent solubility with ethyl alcohol, and is also cosolvent- soluble systems, typically mixtures of alcohols and aliphatic hydrocarbons and / or aromatic. The ITAMID M20P is compatible with most of the phenolic resins, maleic, that tonic, waxes and plasticizers monometric. The ITAMID M20P is generally incompatible with polyesters, vinyl resins and urea. 收起 | Request Sample |
| ITAMID M21P | DKSH | The ITAMID M21P is a solid polyamide resin excellent thermal stability which are mainly used in adhesives Fusion (Hot Melts). The ITAMID M21P is particularly useful for the formulation of inks “flex” and “rotogravure” where over membership, gloss and wate...展开 The ITAMID M21P is a solid polyamide resin excellent thermal stability which are mainly used in adhesives Fusion (Hot Melts). The ITAMID M21P is particularly useful for the formulation of inks “flex” and “rotogravure” where over membership, gloss and water resistance, are also required a higher resistance to ink “gel”, one of his quick recovery from the phase of “gel” and a resistance to “blocking”. The ITAMID M21P has an excellent solubility with ethyl alcohol, and is also cosolvent- soluble systems, typically mixtures of alcohols and aliphatic hydrocarbons and / or aromatic. The ITAMID M21P is compatible with most of the phenolic resins, maleic, that tonic, waxes and plasticizers monometric. The ITAMID M21P is generally incompatible with polyesters, vinyl resins and urea. 收起 | Request Sample |
| ITAMID M30P | DKSH | ITAMID M30P is a thermoplastic polyamide resin for use in flexographic or gravure lamination inks. The product shows excellent adhesion to many substrates (metal or polyolefin). The product has excellent flexibility and is particularly suitable for bondin...展开 ITAMID M30P is a thermoplastic polyamide resin for use in flexographic or gravure lamination inks. The product shows excellent adhesion to many substrates (metal or polyolefin). The product has excellent flexibility and is particularly suitable for bonding of PVC. 收起 | Request Sample |
| ITAMINE CA165 | DKSH | ITAMINE CA 165 is a low viscosity, phenol free, modified cicloalifatic polyamine hardener for solvent free systems or coatings. ITAMINE CA 165 cure fast and produce coatings and flooring with a good aesthetic appearance and high gloss, even at low cure te...展开 ITAMINE CA 165 is a low viscosity, phenol free, modified cicloalifatic polyamine hardener for solvent free systems or coatings. ITAMINE CA 165 cure fast and produce coatings and flooring with a good aesthetic appearance and high gloss, even at low cure temperatures. ITAMINE CA 165 has good resistance to water spotting and also features good blush resistance. 收起 | Request Sample |
| ITAMINE CA30 | DKSH | ITAMINE CA30 is a modified cycloaliphatic polyamine based hardener for Epoxy Resins which is particularly indicated for solvent free coatings, self levelling mortars and adhesives. Due to its low viscosity ITAMINE CA30 is additionally suitable for applica...展开 ITAMINE CA30 is a modified cycloaliphatic polyamine based hardener for Epoxy Resins which is particularly indicated for solvent free coatings, self levelling mortars and adhesives. Due to its low viscosity ITAMINE CA30 is additionally suitable for application systems of pouring, injection (concrete) and in high filled formulates (e.g. epoxy-tar systems): ABSENCE OF PHENOL AND AROMATIC AMINES, EXCELLENT FETURES OF STRENGTH AND RESISTANCE TO CHEMICALS, EXCELLENT SMOOTH FLOW (SELF-LEVELLING) and LOW VISCOSITY. 收起 | Request Sample |
| ITAMINE CA30LA | DKSH | ITAMINE CA30LA is a modified cycloaliphatic polyamine based hardener for Epoxy Resins which is particularly indicated for solvent free coatings, self levelling mortars and adhesives. Due to its low viscosity ITAMINE CA30LA is additionally suitable for app...展开 ITAMINE CA30LA is a modified cycloaliphatic polyamine based hardener for Epoxy Resins which is particularly indicated for solvent free coatings, self levelling mortars and adhesives. Due to its low viscosity ITAMINE CA30LA is additionally suitable for application systems of pouring, injection (concrete) and in high filled formulates (e.g. epoxy-tar systems). 收起 | Request Sample |
| ITAMINE CA51L | DKSH | ITAMINE CA51L is an Epoxy Resins curing agent based on cycloaliphatic amines, it is particularly indicated for room temperature, solvent free systems or coatings. The main properties of ITAMINE CA51L are the following: GOOD LEVELLING AND WETTING CAPACITY,...展开 ITAMINE CA51L is an Epoxy Resins curing agent based on cycloaliphatic amines, it is particularly indicated for room temperature, solvent free systems or coatings. The main properties of ITAMINE CA51L are the following: GOOD LEVELLING AND WETTING CAPACITY, REDUCED CARBONATATION, GOOD ADHESION EVEN ON WET SURFACES, COMPLETE AND RAPID HARDENING EVEN AT 5°C AND WIT H HIGH RELATIVE HUMIDITY (95%), STABLE COLOUR, HIGH GLOSS and GOOD MECHANICAL AND CHEMICAL RESISTANCE. 收起 | Request Sample |
| ITAMINE CA60 | DKSH | ITAMINE CA60 is an Epoxy Resins curing agent based on cycloaliphatic amine adduct, it is particularly indicated for room temperature, solvent free systems, glazes and food covering with low fatty content for example wine and fresh water tank. | Request Sample |
| ITAMINE CA70 | DKSH | ITAMINE CA70 is an Epoxy Resins curing agent based on cycloaliphatic amines. The main properties of ITAMINE CA70 are the following: GOOD LEVELLING AND WETTING CAPACITY, REDUCED CARBONATATION, GOOD ADHESION EVEN ON WET SURFACES, COMPLETE AND RAPID HARDENIN...展开 ITAMINE CA70 is an Epoxy Resins curing agent based on cycloaliphatic amines. The main properties of ITAMINE CA70 are the following: GOOD LEVELLING AND WETTING CAPACITY, REDUCED CARBONATATION, GOOD ADHESION EVEN ON WET SURFACES, COMPLETE AND RAPID HARDENING EVEN AT 5°C AND WIT H HIGH RELATIVE HUMIDITY (95%), STABLE COLOUR, HIGH GLOSS and GOOD MECHANICAL AND CHEMICAL RESISTANCE. ITAMINE CA70 is also indicated for food covering with low fatty content for example wine and fresh water tank. 收起 | Request Sample |
| ITAMINE CA80 | DKSH | ITAMINE CA80 is a modified cycloaliphatic polyamine based hardener for Epoxy Resins which is particularly indicated for solvent free coatings, self levelling mortars and adhesives. Due to its low viscosity ITAMINE CA80 is additionally suitable for applica...展开 ITAMINE CA80 is a modified cycloaliphatic polyamine based hardener for Epoxy Resins which is particularly indicated for solvent free coatings, self levelling mortars and adhesives. Due to its low viscosity ITAMINE CA80 is additionally suitable for application systems of pouring, injection (concrete) and in high filled formulates (e.g. epoxy-tar systems) The main properties of this hardener are the following: COMPLETE CURING EVEN AT LOW TEMPERATURE (0°C), ABSENCE OF PHENOL AND AROMATIC AMINES, EXCELLENT FETURES OF STRENGTH AND RESISTANCE TO CHEMICALS, EXCELLENT SMOOTH FLOW (SELF-LEVELLING) and LOW VISCOSITY. 收起 | Request Sample |
| ITAMINE FL43 | DKSH | ITAMINE FL43 is an liquid epoxy resin hardener made up of modified aliphatic polyamines. ITAMINE FL43 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, encapsulations and paints. Com...展开 ITAMINE FL43 is an liquid epoxy resin hardener made up of modified aliphatic polyamines. ITAMINE FL43 is used in the formulation of epoxy mortars (for laying tiles, repair of concrete, etc.), in the formulation of adhesives, encapsulations and paints. Compared with traditional hardeners, such as polyaminoamide resins, ITAMINE FL43 exhibits greater reactivity, resistance to chemical agents and dilute inorganic acids, and pronounced capacity for reaction at low temperatures. Finally, comparing the classical amine hardeners, which are normally classified as “corrosive” substances, ITAMINE FL43 exhibits lower hazard (it is actually classified only as an “irritating” substance). 收起 | Request Sample |
| Liquid Chlorine | Occidental Chemical Corp. (OxyChem) | Liquid Chlorine is chlorine gas which has been dried, chilled, pressurized, and converted into liquid. This product has a purity of 99.5 percent and a total chloromethanes weight of 175 ppm. Liquid Chlorine is used in various manufacturing applications. | |
| Liquid Chlorine (Pesticide) | Occidental Chemical Corp. (OxyChem) | Liquid Chlorine (Pesticide) is a green to yellow gas which has been turned into an amber liquid. This product has a purity of 99.5 percent and a chloroform weight of 75 ppm. Liquid Chlorine (Pesticide) is used in various manufacturing applications. | |
| Liquid Sodium Silicate Grade 20 Clear | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 20 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.39 and 1.397 and a viscosity of between 150 and 200. Liquid Sodium Silicate Grade 20 Clear is used...展开 Liquid Sodium Silicate Grade 20 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.39 and 1.397 and a viscosity of between 150 and 200. Liquid Sodium Silicate Grade 20 Clear is used in adhesives, paint, coatings, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 30 Clear | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 30 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.408 and 1.413 and a total solids weight percentage of between 37.1 and 38.1. Liquid Sodium Silicat...展开 Liquid Sodium Silicate Grade 30 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.408 and 1.413 and a total solids weight percentage of between 37.1 and 38.1. Liquid Sodium Silicate Grade 30 Clear is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 40 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 40 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.394 and 1.408 and a Silica weight percentage of between 28.74 and 29.74. Liquid Sodium Silicate Grade 40...展开 Liquid Sodium Silicate Grade 40 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.394 and 1.408 and a Silica weight percentage of between 28.74 and 29.74. Liquid Sodium Silicate Grade 40 is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 40 Clear | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 40 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.394 and 1.408 and a viscosity of between 165 and 245. Liquid Sodium Silicate Grade 40 Clear is use...展开 Liquid Sodium Silicate Grade 40 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.394 and 1.408 and a viscosity of between 165 and 245. Liquid Sodium Silicate Grade 40 Clear is used in paint, adhesives, coatings, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 40 Light | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 40 Light is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.39 and 1.397 and a viscosity of between 150 and 200. Liquid Sodium Silicate Grade 40 Light is used...展开 Liquid Sodium Silicate Grade 40 Light is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.39 and 1.397 and a viscosity of between 150 and 200. Liquid Sodium Silicate Grade 40 Light is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 42 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 42 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a weight ratio of between 3.17 and 3.27 and a viscosity of between 330 and 470. Liquid Sodium Silicate Grade 42 is used in paint, adhesi...展开 Liquid Sodium Silicate Grade 42 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a weight ratio of between 3.17 and 3.27 and a viscosity of between 330 and 470. Liquid Sodium Silicate Grade 42 is used in paint, adhesives, coatings, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 42 Heavy | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 42 Heavy is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.410 and 1.424 and a viscosity of between 550 and 990. Liquid Sodium Silicate Grade 40 Light is use...展开 Liquid Sodium Silicate Grade 42 Heavy is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.410 and 1.424 and a viscosity of between 550 and 990. Liquid Sodium Silicate Grade 40 Light is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 47 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 47 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a silica weight percentage of between 31.36 and 32.36 and a sodium monoxide weight percentage of between 10.92 and 11.52. Liquid Sodium ...展开 Liquid Sodium Silicate Grade 47 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a silica weight percentage of between 31.36 and 32.36 and a sodium monoxide weight percentage of between 10.92 and 11.52. Liquid Sodium Silicate Grade 47 is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 49FG | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 49FG is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a weight ratio of between 2.53 and 2.63 and a viscosity of between 550 and 715. Liquid Sodium Silicate Grade 49FG is used in paint, co...展开 Liquid Sodium Silicate Grade 49FG is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a weight ratio of between 2.53 and 2.63 and a viscosity of between 550 and 715. Liquid Sodium Silicate Grade 49FG is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 50 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 50 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a total solids weight percentage of between 43.27 and 44.87 and a viscosity of between 295 and 375. Liquid Sodium Silicate Grade 50 is u...展开 Liquid Sodium Silicate Grade 50 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a total solids weight percentage of between 43.27 and 44.87 and a viscosity of between 295 and 375. Liquid Sodium Silicate Grade 50 is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 50 Clear | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 50 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a turbidity of 15 NTU and a specific gravity of between 1.518 and 1.534. Liquid Sodium Silicate Grade 50 Clear is used in paint, c...展开 Liquid Sodium Silicate Grade 50 Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a turbidity of 15 NTU and a specific gravity of between 1.518 and 1.534. Liquid Sodium Silicate Grade 50 Clear is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade 52 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade 52 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a viscosity of between 1375 and 2200 and a specific gravity of between 1.551 and 1.568. Liquid Sodium Silicate Grade 52 is used in paint...展开 Liquid Sodium Silicate Grade 52 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a viscosity of between 1375 and 2200 and a specific gravity of between 1.551 and 1.568. Liquid Sodium Silicate Grade 52 is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade JW Clear | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade JW Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a turbidity of 10 NTU and a viscosity of between 53 and 73. Liquid Sodium Silicate Grade JW Clear is used in paint, coatings, adhe...展开 Liquid Sodium Silicate Grade JW Clear is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a turbidity of 10 NTU and a viscosity of between 53 and 73. Liquid Sodium Silicate Grade JW Clear is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade JW-25 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade JW-25 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a weight ratio of between 2.49 and 2.59 and a total solids weight percentage of between 36.55 and 38.15. Liquid Sodium Silicate Grade...展开 Liquid Sodium Silicate Grade JW-25 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a weight ratio of between 2.49 and 2.59 and a total solids weight percentage of between 36.55 and 38.15. Liquid Sodium Silicate Grade JW-25 is used in paint, coatings, adhesives, and sealants. 收起 | |
| Liquid Sodium Silicate Grade WD-43 | Occidental Chemical Corp. (OxyChem) | Liquid Sodium Silicate Grade WD-43 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.426 and 1.44 and a weight ratio of between 1.75 and 1.85. Liquid Sodium Silicate Grade WD-43 is used ...展开 Liquid Sodium Silicate Grade WD-43 is an aqueous liquid which contains sodium oxide and silicon dioxide. This product has a specific gravity of between 1.426 and 1.44 and a weight ratio of between 1.75 and 1.85. Liquid Sodium Silicate Grade WD-43 is used in paint, coatings, adhesives, and sealants. 收起 | |
| LITHOL RUBINE 188 | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE 188 is a calcium salt of monoazo lake red pigment with good overall performance. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for water based inks. | |
| LITHOL RUBINE 188A | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE 188A is a calcium salt of monoazo lake red pigment designed for water based inks. It exhibits high color strength, high gloss and transparency. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for ...展开 LITHOL RUBINE 188A is a calcium salt of monoazo lake red pigment designed for water based inks. It exhibits high color strength, high gloss and transparency. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for water based inks and NC inks. 收起 | |
| LITHOL RUBINE 2062 | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE 2062 is a calcium salt of monoazo lake red pigment with a bluish shade. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in offset inks. | |
| LITHOL RUBINE 298A | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE 298A is a calcium salt of monoazo lake red pigment. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in offset inks and PVC. | |
| LITHOL RUBINE BH-07 | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BH-07 is a red pigment with good performance. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for industrial paint and PU. | |
| LITHOL RUBINE BH-300 | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BH-300 is a calcium salt of monoazo lake red pigment with good overall performance in solvent based inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in toluene based inks, industrial...展开 LITHOL RUBINE BH-300 is a calcium salt of monoazo lake red pigment with good overall performance in solvent based inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in toluene based inks, industrial paint, offset inks, and PP inks. 收起 | |
| LITHOL RUBINE BH-300A | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BH-300A is a calcium salt of monoazo lake red pigment with good performance in solvent based inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for PA inks, PP inks, NC inks, and toluene based ...展开 LITHOL RUBINE BH-300A is a calcium salt of monoazo lake red pigment with good performance in solvent based inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for PA inks, PP inks, NC inks, and toluene based inks. 收起 | |
| LITHOL RUBINE BH-461 | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BH-461 is a calcium salt of monoazo lake red pigment. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in toluene based inks and offset inks. | |
| LITHOL RUBINE BH-468 | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BH-468 is a calcium salt of monoazo lake red pigment. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in toluene based inks and offset inks. | |
| LITHOL RUBINE BH-4BP | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BH-4BP is a calcium salt of monoazo lake red pigment with good dispersion and migration resistance. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for powder coatings, PVC, and industrial paint. | |
| LITHOL RUBINE BHA | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BHA is a calcium salt of monoazo lake red pigment with a yellow tint. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in offset inks, UV inks, and toluene based inks. | |
| LITHOL RUBINE BHB | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BHB is a calcium salt of monoazo lake red pigment with a yellow tint. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in NC inks, PP, and UV inks. | |
| LITHOL RUBINE BHD | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BHD is a calcium salt of monoazo lake red pigment with a yellow tint. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in offset inks, UV inks, and PVC. | |
| LITHOL RUBINE BHE | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BHE is a calcium salt of monoazo lake red pigment with good performance in offset inks. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for offset inks and UV inks. | |
| LITHOL RUBINE BHGL | Zhejiang Baihe Chemical Holding Group Company | LITHOL RUBINE BHGL is a calcium salt of monoazo lake red pigment with a bluish tint. It exhibits high transparency and gloss, and has good resistance to solvents. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended...展开 LITHOL RUBINE BHGL is a calcium salt of monoazo lake red pigment with a bluish tint. It exhibits high transparency and gloss, and has good resistance to solvents. This product has an oil absorption of 45-55 ml/100g and a pH value of 7-8. It is recommended for use in PA, NC, UV inks, PP and toluene-based inks. 收起 |
