| Calfax® 10L-45 | Pilot Chemical | Calfax® 10L-45 is a light amber, water soluble surface active agent that contains no halogenated solvents. It is an aqueous surfactant solution that is compatible with a broad range of high electrolyte solutions such as brine, bleach, caustic and inorgani...展开 Calfax® 10L-45 is a light amber, water soluble surface active agent that contains no halogenated solvents. It is an aqueous surfactant solution that is compatible with a broad range of high electrolyte solutions such as brine, bleach, caustic and inorganic acids. The high surface activity and the high electrolyte tolerance of Calfax® 10L-45 make it the surfactant of choice for the manufacture of latex emulsions for adhesives and foam rubber. These properties allow the user to operate the emulsification system under conditions that would not be usable with conventional surface active agents, permitting greater control over latex molecular weight and particle size. 收起 | |
| Calfax® 10LA-75 | Pilot Chemical | Calfax® 10LA-75 is a amber, viscous soluble surface active agent that contains no halogenated solvents. Calfax® 10LA-75 is compatible with a broad range of high electrolyte solutions, such as brine, bleach, caustic and inorganic acids. The linear side cha...展开 Calfax® 10LA-75 is a amber, viscous soluble surface active agent that contains no halogenated solvents. Calfax® 10LA-75 is compatible with a broad range of high electrolyte solutions, such as brine, bleach, caustic and inorganic acids. The linear side chain of Calfax® 10LA-75 promotes emulsification and solubility in organic solvents. It is recommended that Calfax® 10LA-75 be added to water, if a dilution is needed, as high viscosity occurs when water is added to the Calfax® 10LA-75. The high electrolyte tolerance and surface activity of Calfax® 10LA-75 make it the surfactant of choice for making latex emulsions for adhesives and foam rubber. 收起 | |
| Calfax® 16L-35 | Pilot Chemical | Calfax® 16L-35 is an aqueous solution of sodium hexadecyl diphenyl oxide disulfonate, which has a clear light amber appearance and contains no halogenated solvents. Calfax® 16L-35 offers superior solubility and stability in electrolyte solutions such as b...展开 Calfax® 16L-35 is an aqueous solution of sodium hexadecyl diphenyl oxide disulfonate, which has a clear light amber appearance and contains no halogenated solvents. Calfax® 16L-35 offers superior solubility and stability in electrolyte solutions such as brine, bleach, caustic and inorganic acids. The long, linear side chain promotes lower critical micelle concentration (CMC), higher surface tension and lower foam stability than the other Calfax® products. Calfax® 16L-35 offers substantially less foam than shorter chain disulfonates. It is an efficient emulsifier for ABS resins and styrene-butadiene latex, among others. 收起 | |
| Calfax® 6LA-70 | Pilot Chemical | Calfax® 6LA-70 is a clear amber liquid surface active agent that contains no halogenated solvents. It is compatible with a broad range of high electrolyte solutions, such as brine, bleach, caustic and inorganic acids. The linear side chain of Calfax® 6LA-...展开 Calfax® 6LA-70 is a clear amber liquid surface active agent that contains no halogenated solvents. It is compatible with a broad range of high electrolyte solutions, such as brine, bleach, caustic and inorganic acids. The linear side chain of Calfax® 6LA-70 promotes emulsification and solubility in organic solvents. This product is effective as a solubilizer, coupler and hydrotrope for use in acid and alkaline cleaners where conventional surfactants don't have enough solubility. It also finds application in glass cleaners, concentrated laundry detergents, kitchen and bath cleaners, pot and pan, hard surface cleaners and concrete cleaners. 收起 | |
| Calfax® DB-45 | Pilot Chemical | Calfax® DB-45 is a clear light amber aqueous solution of sodium dodecyl branched dipheny oxide disulfonate. It contains no halogenated solvents and is compatible with a broad range of acids, alkalis, chlorine and peroxide bleaches and builders such as sod...展开 Calfax® DB-45 is a clear light amber aqueous solution of sodium dodecyl branched dipheny oxide disulfonate. It contains no halogenated solvents and is compatible with a broad range of acids, alkalis, chlorine and peroxide bleaches and builders such as sodium carbonate and sodium metasilicate. The high surface activity and the high electrolyte tolerance of Calfax® DB-45 make it the surfactant of choice for the manufacture of latex emulsions for adhesives and foam rubber. These properties allow the user to operate the emulsification process under conditions that would not be usable with conventional surface active agents, permitting greater control over latex’s molecular weight and particle size. Calfax® DB-45 also aids in improving a latex emulsion’s thermal and mechanical stability. 收起 | |
| Enamel Grade Titanium Dioxide HTD-E | Hoten Chemical International Group | Enamel Grade Titanium Dioxide HTD-E is a white powder made from a sulfuric acid process. This product has a strong opacity making a thin, smooth and acid resistant coating used in enamel and coloring material. | |
| Epoxy Resin E-10 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin E-10 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow solid granular powder that has good mechanical and anti-corrosive properties. It can be used in paints and powder coatings. | |
| Epoxy Resin E-12 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin E-12 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow, solid granular powder that has good electrostatic spraying performance, chemical resistance, and anti-corrosive properties. It can be used in epoxy polye...展开 Epoxy Resin E-12 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow, solid granular powder that has good electrostatic spraying performance, chemical resistance, and anti-corrosive properties. It can be used in epoxy polyester powder coatings, or mixed with an amine curing agent for use in anti-corrosion and insulation coatings. 收起 | |
| Epoxy Resin E-14 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin E-14 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow, solid granular powder that has good electrostatic spraying performance, chemical resistance, and anti-corrosive properties. It can be used in top-grade e...展开 Epoxy Resin E-14 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow, solid granular powder that has good electrostatic spraying performance, chemical resistance, and anti-corrosive properties. It can be used in top-grade epoxy polyester powder coatings, electrophoretic paints, and anti-corrosion coatings. 收起 | |
| Epoxy Resin E-20 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin E-20 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow, solid granular powder that has good bending performance, chemical resistance, solvent resistance, and strong adhesion properties. It can be used in anti-...展开 Epoxy Resin E-20 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a light yellow, solid granular powder that has good bending performance, chemical resistance, solvent resistance, and strong adhesion properties. It can be used in anti-corrosion coatings, zinc powder primers, floor coatings, decorative coatings and varnishes. 收起 | |
| Epoxy Resin SF801 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin SF801 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent granular powder that is curable at room temperature or higher temperatures. It can be used in anti-corrosion coatings, electrophoretic paint, floor coatin...展开 Epoxy Resin SF801 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent granular powder that is curable at room temperature or higher temperatures. It can be used in anti-corrosion coatings, electrophoretic paint, floor coatings, decorative coatings, and powder coatings. It has an epoxy equivalent of 450-520 g/eq and a softening point of 65-75°C. 收起 | |
| Epoxy Resin SF801A | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin SF801A is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent granular powder that is curable at room temperature or higher temperatures. It can be used in anti-corrosion coatings, electrophoretic paint, floor coati...展开 Epoxy Resin SF801A is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent granular powder that is curable at room temperature or higher temperatures. It can be used in anti-corrosion coatings, electrophoretic paint, floor coatings, decorative coatings, and powder coatings. It has an epoxy equivalent of 530-570 g/eq and a softening point of 65-75°C. 收起 | |
| Epoxy Resin SF808 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin SF808 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good electrostatic spraying performance and plate leveling capacity. It can be used in top-grade epoxy polyester powder co...展开 Epoxy Resin SF808 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good electrostatic spraying performance and plate leveling capacity. It can be used in top-grade epoxy polyester powder coatings, electrophoretic paints, and anti-corrosion coatings. 收起 | |
| Epoxy Resin SF818 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin SF818 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good mechanical performance and electrostatic spraying performance. It can be used in electrophoretic paints, top-grade ep...展开 Epoxy Resin SF818 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good mechanical performance and electrostatic spraying performance. It can be used in electrophoretic paints, top-grade epoxy poleyster powder coatings, and anti-corrosion coatings. 收起 | |
| Epoxy Resin SF828 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin SF828 is a MMW solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good electrostatic spraying performance, chemical resistance, and high impact strength. It can be used in electrophoretic ...展开 Epoxy Resin SF828 is a MMW solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good electrostatic spraying performance, chemical resistance, and high impact strength. It can be used in electrophoretic paints, top-grade epoxy polyester powder coatings, and anti-corrosion coatings. 收起 | |
| Epoxy Resin SF838 | Anhui Shanfu New Material Technology Co., Ltd. | Epoxy Resin SF838 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good chemical resistance, electrostatic spraying performance, and anti-corrosive properties. It can be used in electrophor...展开 Epoxy Resin SF838 is a MMW-solid Bisphenol-A type epoxy resin. This product appears as a transparent, solid granular powder that has good chemical resistance, electrostatic spraying performance, and anti-corrosive properties. It can be used in electrophoretic paints and anti-corrosion coatings. 收起 | |
| HESS NCS-10 | Hess Pumice (NCS) Microfine Functional Fillers | HESS NCS-10 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resist...展开 HESS NCS-10 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resistance properties due to the hardness of the particles. 收起 | |
| HESS NCS-12 | Hess Pumice (NCS) Microfine Functional Fillers | HESS NCS-12 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resist...展开 HESS NCS-12 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resistance properties due to the hardness of the particles. 收起 | |
| HESS NCS-15 | Hess Pumice (NCS) Microfine Functional Fillers | HESS NCS-15 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resist...展开 HESS NCS-15 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resistance properties due to the hardness of the particles. 收起 | |
| HESS NCS-3 | Hess Pumice (NCS) Microfine Functional Fillers | HESS NCS-3 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resista...展开 HESS NCS-3 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resistance properties due to the hardness of the particles. 收起 | |
| HESS NCS-5 | Hess Pumice (NCS) Microfine Functional Fillers | HESS NCS-5 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resista...展开 HESS NCS-5 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resistance properties due to the hardness of the particles. 收起 | |
| HESS NCS-8 | Hess Pumice (NCS) Microfine Functional Fillers | HESS NCS-8 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resista...展开 HESS NCS-8 is a non-crystalline silica (NCS) made from pure, white pumice. It can be used as a functional filler and extender in paints and coatings. This product is inert, near white, has a pH of 7.2, and has outstanding scrub, burnish, and stain resistance properties due to the hardness of the particles. 收起 | |
| HTM-A Barium Sulphate Modified | Hoten Chemical International Group | HTM-A Barium Sulphate Modified is a function filler of nano-meterclass specifically created for electronic printing and writing ink. This product is noted for an efficient pigment dispersibility and to fully retain pigment grains around it, in turn creati...展开 HTM-A Barium Sulphate Modified is a function filler of nano-meterclass specifically created for electronic printing and writing ink. This product is noted for an efficient pigment dispersibility and to fully retain pigment grains around it, in turn creating a pure vivid color image. 收起 | |
| HTM-B Barium Sulphate Modified | Hoten Chemical International Group | HTM-B Barium Sulphate Modified is a function filler of nanometer-class developed for electronic printing and writing ink. This product is noted for an efficient pigment dispersibility and to fully retain pigment grains around it, in turn creating a pure v...展开 HTM-B Barium Sulphate Modified is a function filler of nanometer-class developed for electronic printing and writing ink. This product is noted for an efficient pigment dispersibility and to fully retain pigment grains around it, in turn creating a pure vivid color image. 收起 | |
| HTM-C Barium Sulphate Modified | Hoten Chemical International Group | HTM-C Barium Sulphate Modified is a function filler of nano-meterclass specifically created for electronic printing and writing ink. This product is noted for an efficient pigment dispersibility and to fully retain pigment grains around it, in turn creati...展开 HTM-C Barium Sulphate Modified is a function filler of nano-meterclass specifically created for electronic printing and writing ink. This product is noted for an efficient pigment dispersibility and to fully retain pigment grains around it, in turn creating a pure vivid color image. 收起 | |
| HTN-NO Barium Sulfate Natural | Hoten Chemical International Group | HTN-NO Barium Sulfate Natural is a natural function filler that can be used in paint and improve concentration of coatings. | |
| HTN-NP Barium Sulfate Natural | Hoten Chemical International Group | HTN-NP Barium Sulfate Natural is a natural filler than can be used to improve the concentration of coatings and reduce levels of resin and solvent in formulas for cost-cutting measures. | |
| HTN-NQ Barium Sulfate Natural | Hoten Chemical International Group | HTN-NQ Barium Sulfate Natural is a natural filler than can be used to improve the concentration of coatings and reduce levels of resin and solvent in formulas for cost-cutting measures. | |
| HTN-NR Barium Sulfate Natural | Hoten Chemical International Group | HTN-NR Barium Sulfate Natural is a natural filler than can be used to improve the concentration of coatings and reduce levels of resin and solvent in formulas for cost-cutting measures. | |
| HTN-NS Barium Sulfate Natural | Hoten Chemical International Group | HTN-NS Barium Sulfate Natural is a natural filler than can be used to improve the concentration of coatings and reduce levels of resin and solvent in formulas for cost-cutting measures. | |
| HTS-H Synthetic Barium Sulfate | Hoten Chemical International Group | HTS-H Synthetic Barium Sulfate is a chemically synthesized barium sulfate derived from the processing of barium salt and sodium sulfate. As a filler, it can be used to cut costs on resin, and has good light fastness, weathering resistance, and narrow dist...展开 HTS-H Synthetic Barium Sulfate is a chemically synthesized barium sulfate derived from the processing of barium salt and sodium sulfate. As a filler, it can be used to cut costs on resin, and has good light fastness, weathering resistance, and narrow distribution of grain sizes. This product is used in several coating applications. 收起 | |
| HTS-L Synthetic Barium Sulfate | Hoten Chemical International Group | HTS-L Synthetic Barium Sulfate is a chemically synthesized barium sulfate product derived from pure barium salt and sodium sulfate. As a filler, it can be used to cut costs on resin, and has good light fastness, weathering resistance, and narrow distribut...展开 HTS-L Synthetic Barium Sulfate is a chemically synthesized barium sulfate product derived from pure barium salt and sodium sulfate. As a filler, it can be used to cut costs on resin, and has good light fastness, weathering resistance, and narrow distribution of grain sizes. This product is used in several coating applications. 收起 | |
| HTS-M Synthetic Barium Sulfate | Hoten Chemical International Group | HTS-M Synthetic Barium Sulfate is a chemically synthesized barium sulfate product derived from pure barium salt and sodium sulfate. As a filler, it can be used to cut costs on resin, and has good light fastness, weathering resistance, and narrow distribut...展开 HTS-M Synthetic Barium Sulfate is a chemically synthesized barium sulfate product derived from pure barium salt and sodium sulfate. As a filler, it can be used to cut costs on resin, and has good light fastness, weathering resistance, and narrow distribution of grain sizes. This product is used in several coating applications. 收起 | |
| Masurf® UV-350 | Pilot Chemical | Masurf® UV-350 is an Ultraviolet Light Absorber for non-polar, hydrocarbon solvent systems, designed to impart UV protection to fabrics and hard surfaces. Utilizing proven and accepted benzotriazole UV absorber chemistry, this product is easy to use and h...展开 Masurf® UV-350 is an Ultraviolet Light Absorber for non-polar, hydrocarbon solvent systems, designed to impart UV protection to fabrics and hard surfaces. Utilizing proven and accepted benzotriazole UV absorber chemistry, this product is easy to use and highly efficient, because it is applied from a solution. Masurf® UV-350 is readily dissolvable in hydrocarbon solvents which provides a uniform coverage compared to other UV absorbers that form unstable, large particle size dispersions and yield non-uniform surface coverage. Unlike aqueous based UV absorbers, this product is not water soluble, so it will not readily wash off exterior surfaces. 收起 | |
| Nitrocellulose Chips | Hengshui New Eastern Chemical Industry Co,. Ltd. | Nitrocellulose chips are a white flaky or powdery fiber. This product has a low moisture rate and is used to formulate high brightness paints and coatings. This product is well suited for use in fast-drying automobile lacquers, printing inks, coatings, an...展开 Nitrocellulose chips are a white flaky or powdery fiber. This product has a low moisture rate and is used to formulate high brightness paints and coatings. This product is well suited for use in fast-drying automobile lacquers, printing inks, coatings, and damp-proofing cellophane paper and adhesives. 收起 | |
| Nitrocellulose Cotton | Hengshui New Eastern Chemical Industry Co,. Ltd. | Nitrocellulose cotton is a white floc and chips fiber made from refined cotton and nitric acid. It can be liquified in acetonet, ethyl acetate, camphor ethanol liquid. This product is well suited for producing any color celluloid, nitryl lacquers, wood fi...展开 Nitrocellulose cotton is a white floc and chips fiber made from refined cotton and nitric acid. It can be liquified in acetonet, ethyl acetate, camphor ethanol liquid. This product is well suited for producing any color celluloid, nitryl lacquers, wood finishes, and fast-printing inks. 收起 | |
| Nitrocellulose Solution H Type | Hengshui New Eastern Chemical Industry Co,. Ltd. | Nitrocellulose solution H type is a slightly sticky yellowish liquid made from high nitrogen content nitrocellulose. It has good miscibility and can be mixed with alkyd, maleic resin, and acrylic resin. It is quick drying and forms a hard durable film. Th...展开 Nitrocellulose solution H type is a slightly sticky yellowish liquid made from high nitrogen content nitrocellulose. It has good miscibility and can be mixed with alkyd, maleic resin, and acrylic resin. It is quick drying and forms a hard durable film. This product is well suited for use in lacquers for wood and plastic. 收起 | |
| Nitrocellulose solution L type | Hengshui New Eastern Chemical Industry Co,. Ltd. | Nitrocellulose solution L type is a slightly sticky yellowish liquid made from low nitrogen content nitrocellulose. It has good miscibility and is alcohol soluble. It is quick drying and forms a hard durable film. This product is well suited for use in la...展开 Nitrocellulose solution L type is a slightly sticky yellowish liquid made from low nitrogen content nitrocellulose. It has good miscibility and is alcohol soluble. It is quick drying and forms a hard durable film. This product is well suited for use in lacquers for wood and plastic. 收起 | |
| ORGASOL® 1002 D NAT 1 | Arkema 阿科玛 | ORGASOL® 1002 D NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-6 powder reduces the coefficient of friction a...展开 ORGASOL® 1002 D NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-6 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent born or solvent-free technology with reduced impact on rheology. High melting point temperature, above 210°C. The average diameter of 20µm. 收起 | |
| ORGASOL® 1002 ES5 NAT 1 | Arkema 阿科玛 | ORGASOL® 1002 ES5 NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-6 powder reduces the coefficient of friction...展开 ORGASOL® 1002 ES5 NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-6 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption make it suitable as well in waterborne, solvent born or solvent-free technology with reduced impact on rheology. High melting point temperature, above 210°C. The average diameter of 50µm. 收起 | |
| ORGASOL® 2001 EXD NAT 1 | Arkema 阿科玛 | ORGASOL® 2001 EXD NAT 1 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction...展开 ORGASOL® 2001 EXD NAT 1 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 10µm. 收起 | |
| ORGASOL® 2001 UD NAT 1 | Arkema 阿科玛 | ORGASOL® 2001 UD NAT 1 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction ...展开 ORGASOL® 2001 UD NAT 1 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 5µm. 收起 | |
| ORGASOL® 2001 UD NAT 2 | Arkema 阿科玛 | ORGASOL® 2001 UD NAT 2 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction ...展开 ORGASOL® 2001 UD NAT 2 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 5µm. Compliant with FDA regulations (FDA 177-1500 and FDA 175-300). 收起 | |
| ORGASOL® 2002 D NAT 1 | Arkema 阿科玛 | ORGASOL® 2002 D NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction ...展开 ORGASOL® 2002 D NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption in waterborne, solvent born, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 20µm. 收起 | |
| ORGASOL® 2002 ES3 NAT 3 | Arkema 阿科玛 | ORGASOL® 2002 ES3 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of frictio...展开 ORGASOL® 2002 ES3 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 30µm. 收起 | |
| ORGASOL® 2002 ES4 NAT 3 | Arkema 阿科玛 | ORGASOL® 2002 ES4 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of frictio...展开 ORGASOL® 2002 ES4 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 40µm. 收起 | |
| ORGASOL® 2002 ES5 NAT 3 | Arkema 阿科玛 | ORGASOL® 2002 ES5 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of frictio...展开 ORGASOL® 2002 ES5 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 50µm. 收起 | |
| ORGASOL® 2002 ES6 NAT 3 | Arkema 阿科玛 | ORGASOL® 2002 ES6 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of frictio...展开 ORGASOL® 2002 ES6 NAT 3 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology melting temperature is 177. The average rate diameter of 60µm. 收起 | |
| ORGASOL® 2002 EXD NAT 1 | Arkema 阿科玛 | ORGASOL® 2002 EXD NAT 1 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction...展开 ORGASOL® 2002 EXD NAT 1 is used as a matting agent (from satin to deep matt) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. This polyamide-12 powder reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 177°C. The average diameter of 10µm. Compliant with FDA regulations (FDA 177-1500 and FDA 175-300). 收起 | |
| ORGASOL® 3501 EXD NAT 1 | Arkema 阿科玛 | ORGASOL® 3501 EXD NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. The porosity of this copolyamide-6/12 powder grade permits ...展开 ORGASOL® 3501 EXD NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. The porosity of this copolyamide-6/12 powder grade permits absorption exceeds of solvent in the ink-receptive layer for the transfer paper market. It reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 142°C. The average diameter of 10µm. 收起 | |
| ORGASOL® 3502 D NAT 1 | Arkema 阿科玛 | ORGASOL® 3502 D NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. The porosity of this copolyamide-6/12 powder grade permits ab...展开 ORGASOL® 3502 D NAT 1 is used as a matting agent (from satin to deep matte) in all kinds of coatings, varnishes, or ink in addition to improving abrasion, scratch, scrub and burnish resistance. The porosity of this copolyamide-6/12 powder grade permits absorption exceeds of solvent in the ink-receptive layer for the transfer paper market. It reduces the coefficient of friction and provides haptic properties (from soft touch/smooth to textured), flexibility, and blocking resistance. The low oil absorption makes it suitable as well in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 142°C. The average diameter of 20µm. 收起 | |
| RILSAN® D30 NAT | Arkema 阿科玛 | RILSAN® D30 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it sui...展开 RILSAN® D30 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it suitable in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 186°C. The average diameter of 21-27µm. 收起 | |
| RILSAN® D40 NAT | Arkema 阿科玛 | RILSAN® D40 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it sui...展开 RILSAN® D40 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it suitable in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 186°C. The average diameter of 27-31µm. 收起 | |
| RILSAN® D50 NAT | Arkema 阿科玛 | RILSAN® D50 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it su...展开 RILSAN® D50 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it suitable in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 186°C. The average diameter of 40-46µm. 收起 | |
| RILSAN® D60 NAT | Arkema 阿科玛 | RILSAN® D60 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it sui...展开 RILSAN® D60 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it suitable in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 186°C. The average diameter of 43-55µm. 收起 | |
| RILSAN® D80 NAT | Arkema 阿科玛 | RILSAN® D80 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it su...展开 RILSAN® D80 NAT is a 100% bio-based polyamide 11 used to texture all kinds of coatings, varnishes, or ink in addition to improving abrasion and scratch resistance. This polyamide-11 powder provides anti-slip properties. The low oil absorption makes it suitable in waterborne, solvent-borne, or solvent-free technology with reduced impact on rheology. The melting point temperature is 186°C. The average diameter of 95-105µm. 收起 | |
| Titanium Dioxide Anatase | Hoten Chemical International Group | Titanium Dioxide Anatase is a white powder derived from titanium concentrates and sulfuric acid. This anatase titanium dioxide pigment can provide whiteness, gloss, and high intensity in paints, coatings, and printing inks. | |
| Titanium Dioxide Rutile for Paint Industry HTD-R100 | Hoten Chemical International Group | Titanium Dioxide Rutile for Paint Industry HTD-R100 is a white powder derived from titanium concentrates and sulfuric acid. This rutile titanium dioxide pigment surface is treated by inorganic alumina and silicon to provide whiteness, gloss, high tinting ...展开 Titanium Dioxide Rutile for Paint Industry HTD-R100 is a white powder derived from titanium concentrates and sulfuric acid. This rutile titanium dioxide pigment surface is treated by inorganic alumina and silicon to provide whiteness, gloss, high tinting strength, durability and dispersion properties to coating, paint, and printing inks. 收起 | |
| Titanium Dioxide Rutile HTD-R100 | Hoten Chemical International Group | Titanium Dioxide Rutile HTD-R100 is a white powder derived from titanium concentrates and sulfuric acid. This rutile titanium dioxide pigment surface is treated by inorganic alumina and silicon to provide whiteness, gloss, high tinting strength, durabilit...展开 Titanium Dioxide Rutile HTD-R100 is a white powder derived from titanium concentrates and sulfuric acid. This rutile titanium dioxide pigment surface is treated by inorganic alumina and silicon to provide whiteness, gloss, high tinting strength, durability and dispersion properties to coating, paint, and printing ink. 收起 |
