Do The Bump!
Paid Content by Protomold
Nobody’s Faster In The Short Run.®
A bump-off is a small undercut in a part design that can be safely removed from a straight-pull mold without the use of side actions. It works like the snaps on the wind flap of a parka or the snaps on a western style shirt—push to close, pull to open. If you look very closely at the two parts of a snap, you will see that there is slight deformation of the material when the snap is opened or closed. The choice of material and design of the snap’s components allows that deformation to take place without damage or significant wear to the mating parts. This is exactly what happens during the ejection of a part with a bump-off feature.
In the case of a plastic part in an aluminum mold, any deformation that takes place at ejection will be entirely in the plastic part, not in the mold. A number of factors determine the ability of a part to be “bumped-off” without damage. These include the shape of the undercut itself, the resin used to form the part, the geometry of the area surrounding the undercut, and the design of the mold.
Figures 1 and 2 address the shape of the undercut feature. In order to be successfully bumped-off, the leading edge of an undercut must provide a “ramp” or radius like that in Figure 1 rather than a hook or sharp edge as shown in Figure 2. If other factors are correct, during ejection the ramp-shaped lip inside the cylinder in Figure 1 can ride up over the edge of the groove in the mold that formed it, much as a car rides over a speed bump. Conversely, the hook in Figure 2 will remain lodged in the groove that formed it and either prevent ejection entirely or be torn off when the part is ejected.
Resin choice is critical to the success of a bump-off. Depending on the shape of the part, the resin will need to stretch and/or bend during ejection and then return to its original shape and size. A resin like TPE or unfilled polyethylene is flexible enough to bump off. Glass-filled nylon, on the other hand, is very rigid and is not likely to work very well.
Finally, we consider the shape of the part and the molding technique. If Figure 1 is, for example, a snap-on cap for a bottle, Figure 3 shows cross sections representing different ways in which that cap could be made. Figure 3.1 and 3.2 show ways in which the part could be molded as a rib. In this approach, both the outside and inside of the cap are formed by the B-side mold half; the A-side is simply a flat surface that forms the bottom of the upturned cap. Figure 3.3 shows the part as it would be produced by core-cavity molding, the outside formed by the A-side and the inside by the B-side mold halves.
The approach shown in Figure 4 is problematic because during ejection the bump will have to squeeze out through the thinner rib section below it. This requires that the resin be compressed during ejection, and few resins other than low durometer TPEs or TPUs are that compressible. A better approach is shown in Figure 5. Here the raised ring is replaced by an inward bend in the vertical wall of the part. Instead of being compressed, the wall of the part can be “snaked out” during ejection, requiring only that it bend and stretch. This is easier for most resins to do than to compress. You can see an example of this bump-off in our new Protomold Torus complex feature sample. (To request a Torus, click the banner in this Design Tip.)
A third approach is shown in Figure 6. Here the part is formed between a cavity in the A-side mold half and a core in the B-side. After cooling, the mold opens, leaving the part on the core. With nothing pressing against the outside of the part, the part wall is free to stretch as it is ejected off the B-side core, releasing the part with the inside ring intact.
If you have questions about the feasibility of bump-offs for small undercuts in your part design, Proto Labs customer service engineers are here to help and can be reached at 877-479-3680.
Minimize downtime with Prospector’s essential processing data & tools
Access an injection molding troubleshooter, compare up to 5 materials side by side, and even view typical properties to help fill in missing product data points. All this right from the shop floor since Prospector is mobile-friendly. Instantly use advanced data and tools to minimize downtime – subscribe now!
Click to learn more
The views, opinions and technical analyses presented here are those of the author or advertiser, and are not necessarily those of ULProspector.com or UL Solutions. The appearance of this content in the UL Prospector Knowledge Center does not constitute an endorsement by UL Solutions or its affiliates.
All content is subject to copyright and may not be reproduced without prior authorization from UL Solutions or the content author.
The content has been made available for informational and educational purposes only. While the editors of this site may verify the accuracy of its content from time to time, we assume no responsibility for errors made by the author, editorial staff or any other contributor.
UL Solutions does not make any representations or warranties with respect to the accuracy, applicability, fitness or completeness of the content. UL Solutions does not warrant the performance, effectiveness or applicability of sites listed or linked to in any content.